Oxygen flux influence on the morphological, structural and optical properties of Zn1−xMgxO thin films grown by plasma-assisted molecular beam epitaxy

The Zn_1−xMg_xO thin films were grown on Al₂O₃ substrate with various O₂ flow rates by plasma-assisted molecular beam epitaxy (P-MBE). The growth conditions were optimized by the characterizations of morphology, structural and optical properties. The Mg content of the Zn_1−xMg_xO thin film increases monotonously with decreasing the oxygen flux. X-ray diffractometer (XRD) measurements show that all the thin films are preferred (0 0 2) orientated. By transmittance and absorption measurements, it was found that the band gap of the film decreases gradually with increasing oxygen flow rate. The surface morphology dependent on the oxygen flow rate was also studied by field emission scanning electron microscopy (FE-SEM). The surface roughness became significant with increasing oxygen flow rate, and the nanostructures were formed at the larger flow rate. The relationship between the morphology and the oxygen flow rate of Zn_1−xMg_xO films was discussed.     

Structural, optical and electrical properties of Zn1−xCdxO thin films prepared by PLD

Ternary polycrystalline Zn_1−xCd_xO semiconductor films with cadmium content x ranging from 0 to 0.23 were obtained on quartz substrate by pulse laser deposited (PLD) technique. X-ray diffraction measurement revealed that all the films were single phase of wurtzite structure grown on c-axis orientation with its c-axis lattice constant increasing as the Cd content x increasing. Atomic force microscopy observation revealed that the grain size of Zn_1−xCd_xO films decreases continuously as the Cd content x increases. Both photoluminescence and optical measurements showed that the band gap decreases from 3.27 to 2.78 eV with increasing the Cd content x. The increase in Cd content x also leads to the broadening of the emission peak. The resistivity of Zn_1−xCd_xO films decreases evidently for higher values of Cd content x. The shift of PL emission to visible light as well as the decrease of resistivity makes the Zn_1−xCd_xO films potential candidate for optoelectronic device.     

Properties of MgxZn1−xO thin films sputtered in different gases

Mg_xZn_1−xO alloy films were prepared on sapphire substrates using Ar and N₂ as the sputtering gases. The effect of the sputtering gas on the structural, optical and electrical properties of the Mg_xZn_1−xO films was studied. By using N₂ as the sputtering gas, the Mg_xZn_1−xO film shows p-type conductivity and the band gap is larger than that employing Ar as the sputtering gas. The reason for this phenomenon is thought to be related to the reaction between N-O or N-Zn, and the N-doping.     

Growth of cubic MgxZn1−xO alloy films by electron beam evaporation

We report the growth of cubic Mg_xZn_1−xO alloy thin films on quartz by electron beam evaporation. It can be found that all the samples have sharp absorption edges by the absorption measurements. X-ray diffraction measurements indicate the Mg_xZn_1−xO films are cubic phase with preferred orientation along the (1 1 1) direction. Energy dispersive spectrometry (EDS) demonstrates that the Mg concentration in Mg_xZn_1−xO films is much higher than the ceramic target used, and the composition can be tuned in a small scope by varying the substrate temperature and the beam electric current. The reasons of this phenomenon are also discussed.     

Effect of substrate temperature on the morphology, structural and optical properties of Zn1−xCoxO thin films

Zn_1−xCo_xO thin films with c-axis preferred orientation were deposited on sapphire (0 0 0 1) by pulsed laser deposition (PLD) technique at different substrate temperatures in an oxygen-deficient ambient. The effect of substrate temperature on the microstructure, morphology and the optical properties of the Zn_1−xCo_xO thin films was studied by means of X-ray diffraction (XRD), atomic force microscopy (AFM), UV-visible-NIR spectrophotometer, fluorescence spectrophotometer. The results showed that the crystallization of the films was promoted as substrate temperature rose. The structure of the samples was not distorted by the Co incorporating into ZnO lattice. The surface roughness of all samples decreased as substrate temperature increased. The Co concentration in the film was higher than in the target. Emission peak near band edge emission of ZnO from the PL spectra of the all samples was quenched because the dopant complexes acted as non-radiative centers. While three emission bands located at 409 nm (3.03 eV), 496 nm (2.5 eV) and 513 nm (2.4 eV) were, respectively, observed from the PL spectra of the four samples. The three emission bands were in relation to Zn interstitials, Zn vacancies and the complex of V_O and Zn_i (V_OZn_i). The quantity of the Zn interstitials maintained invariable basically, while the quantity of the V_OZn_i slightly decreased as substrate temperature increased.     

The optical properties of CdxZn1−xS thin films on glass substrate prepared by spray pyrolysis method

A series of Cd_xZn_1−xS thin films have been deposited on glass substrates using spray pyrolysis technique. The crystallinity and microstructure of Cd_xZn_1−xS thin films have been investigated by X-ray diffraction (XRD). Based on the results of Hall measurements, the films obtained were an n-type semiconductor. The X-ray data analysis of Cd_xZn_1−xS thin films showed that the grain size of the Cd_xZn_1−xS increased with increase in Cd composition. It is observed that the band gap increases as the Cd composition decreases. The results also showed a blue shift of absorption edge of optical transmission spectra is increases as Zn ratio increases. The effects of Cd composition on the structural and optical properties of Cd_xZn_1−xS thin films were related to their grain size, stress and carrier concentration.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.     

Electric-field-induced energy spectra and dispersions of ZnO/MgxZn1−xO MQWs

The energy spectra and dispersion relations of carriers in the presence of an electric field applied along the growth direction in ZnO/Mg_xZn_1−xO multiple quantum wells (MQW) are calculated using the asymptotic transfer method (ATM) on the basis of the quasistationary state approximation. The energy spectra of the carriers induce some quasi-bound levels under electric fields. The dispersion relations for the energy of the ground state and lower excitation states still have parabolic shapes for both the electrons and the heavy holes in the presence of a moderate electric field. Our results also reveal that the number of energy levels increases with increasing number of ZnO quantum wells and that the energies increase with both increasing Mg composition x and electric field strength.     

Characterization and properties of ZnO1−xSx alloy films fabricated by radio-frequency magnetron sputtering

A series of ZnO_1−xS_x alloy films (0 ≤ x ≤ 1) were grown on quartz substrates by radio-frequency (rf) magnetron sputtering of ZnS ceramic target, using oxygen and argon as working gas. X-ray diffraction measurement shows that the ZnO_1−xS_x films have wurtzite structure with (0 0 2) preferential orientation in O-rich side (0 ≤ x ≤ 0.23) and zinc blende structure with (1 1 1) preferential orientation in S-rich side (0.77 ≤ x ≤ 1). However, when the S content is in the range of 0.23 < x < 0.77, the ZnO_1−xS_x film consists of two phases of wurtzite and zinc blende or amorphous ZnO_1−xS_x phase. The band gap energy of the films shows non-linear dependence on the S content, with an optical bowing parameter of about 2.9 eV. The photoluminescence (PL) measurement reveals that the PL spectrum of the wurtzite ZnO_1−xS_x is dominated by visible band and its PL intensity and intensity ratio of UV to visible band decrease greatly compared with undoped ZnO. All as-grown ZnO_1−xS_x films behave insulating, but show n-type conductivity for w-ZnO_1−xS_x and maintain insulating properties for β-ZnO_1−xS_x after annealed. Mechanisms of effects of S on optical and electrical properties of the ZnO_1−xS_x alloy are discussed in the present work.     

Annealing effect on the structural and optical properties of a Cd1−xZnxS thin film for photovoltaic applications

Herein is a report of a study on a Cd_1−xZn_xS thin film grown on an ITO substrate using a chemical bath deposition technique. The as-deposited films were annealed in air at 400 °C for 30 min. The composition, surface morphology and structural properties of the as-deposited and annealed Cd_1−xZn_xS thin films were studied using EDX, SEM and X-ray diffraction techniques. The annealed films have been observed to possess a crystalline nature with a hexagonal structure. The optical absorption spectra were recorded within the range of 350-800 nm. The band gap of the as-deposited thin films varied from 2.46 to 2.62 eV, whereas in the annealed film these varied from 2.42 to 2.59 eV. The decreased band gap of the films after annealing was due to the improved crystalline nature of the material.     

The optical properties of MgxZnl-xO thin films

Mg_xZn_1-xO thin films have been prepared on silicon substrates by radio frequency magnetron sputtering at 60℃. The thin films have hexagonal wurtzite single-phase structure and a preferred orientation with the c-axis perpendicular to the substrates. The refractive indices of Mg_xZn_1-xO films are studied at room temperature by spectroscopic ellipsometry over the wavelength range of 400--760\,nm at the incident angle of 70℃. Both absorption coefficients and optical band gaps of Mg_xZn_1-xO films are determined by the transmittance spectra. While Mg content is increasing, the absorption edges of Mg_xZn_1-xO films shift to higher energies and band gaps linearly increase from 3.24.eV at x=0 to 3.90\,eV at x=0.30. These results provide important information for the design and modelling of ZnO/ Mg_xZn_1-xO heterostructure optoelectronic devices.     

The effect of growth ambient on the structural and optical properties of MgxZn1−xO thin films

Mg_xZn_1−xO (x = 0.0-0.20) thin films have been deposited by sol-gel technique on glass substrates and the effect of growth ambient (air and oxygen) on the structural, and optical properties have been investigated. The films synthesized in both ambient have hexagonal wurtzite structure. The c-axis lattice constant decreases linearly with the Mg content (x) up to x = 0.05, and 0.10 respectively for air- and oxygen-treated films, above which up to x = 0.20, the values vary irregularly with x. The change in the optical band gap values and the ultraviolet (UV) peak positions of Mg_xZn_1−xO films show the similar change with x. These results suggest that the formation of solid solution and thus the structural and optical properties of Mg_xZn_1−xO thin films are affected by the growth ambient.     

Cu(In,Ga)Se2 superstrate-type solar cells with Zn1−xMgxO buffer layers

Superstrate-type Cu(In,Ga)Se₂ (CIGS) thin film solar cells were fabricated using Zn_1−xMg_xO buffer layers. Due to the diffusion of Cd into CIGS during the growth of the CIGS layer, the conventional buffer material of CdS is not suitable. ZnO is a good candidate because of higher thermal tolerance but the conduction band offset (CBO) of ZnO/CIGS is not appropriate. In this study, the Zn_1−xMg_xO buffer layers were used to fulfill both the requirements. The superstrate-type solar cells with a soda-lime glass/In₂O₃:Sn/Zn_1−xMg_xO/CIGS/Au structure were fabricated with different band gap energies of the Zn_1−xMg_xO layer. The CIGS layers [Ga/(In + Ga)∼0.25] were deposited by co-evaporation method. The substrate temperature during the CIGS deposition of 450 °C did not cause the intermixing of the Zn_1−xMg_xO and CIGS layers. The conversion efficiency of the cell with Zn_1−xMg_xO was higher than that with ZnO due to the improvement of open-circuit voltage and shunt resistance. The results well corresponded to the behavior of the adjustment of CBO, demonstrating that the usefulness of the Zn_1−xMg_xO layer for the CBO control in the superstrate-type CIGS solar cells.     

Zn$lt;sub$gt;1-$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;Mg$lt;sub$gt;$lt;i$gt;x$lt;/i$gt;$lt;/sub$gt;O薄膜的光致发光特性研究

采用脉冲激光沉积方法在单晶Si（100）衬底上制备出c轴取向的Zn_1-xMg_xO单晶薄膜,通过荧光光谱仪研究了薄膜的光致发光特性.实验结果表明,Mg含量增加,Zn_1-xMg_xO单晶薄膜的紫外发光峰蓝移,发光峰强度减弱,缺陷发光强度增强.同时发现,由于Mg的掺杂,引入了一些束缚能较大的局域束缚态.对于氧气氛下制备的样品,实验发现紫外峰和绿光带发光峰同时增强,但是R值减小,紫外峰红移.对绿光发光机理研究发现,绿光发光带主要与锌空位、氧间隙（O_i）或锌位氧（O_Zn）等缺陷有关,它是由多个缺陷发光峰组成,各缺陷发光峰强度相对变化导致了绿光发光带的整体移动. 关键词： 1-xMg_xO薄膜')" href="#">Zn_1-xMg_xO薄膜 光致发光 脉冲激光沉积     

制备工艺对Zn1-xMgxO薄膜结构及光学性能的影响

采用脉冲激光沉积（PLD）方法在单晶Si（100）衬底上沿c轴方向生长单晶Zn_1-xMg_xO薄膜,通过X射线衍射（XRD）、原子力显微镜（AFM）、扫描电镜（SEM）和荧光光谱（PL）研究了膜厚、Mg含量、退火温度及氧气氛等制备工艺对Zn_1-xMg_xO薄膜的结构、形貌和光学性质的影响.实验结果表明,Mg含量x≤0.15时, Zn_{关键词： 1-x}Mg_xO薄膜')" href="#">Zn_1-xMg_xO薄膜 制备工艺 结构 光学性质     

Structural,optical, FTIR and photoluminescence properties of Zn0.96−xCo0.04CuxO (x=0.03, 0.04 and 0.05) nanopowders

Un-hydrogenated and hydrogenated Cu, Co co-doped ZnO (Zn_0.96−xCo_0.04Cu_xO, x=0.03, 0.04 and 0.05) nanopowders have been synthesized by co-precipitation method. The synthesized samples have been characterized by powder X-ray diffraction, energy dispersive X-ray spectra, UV–Visible spectrophotometer and Fourier transform infrared spectroscopy. The calculated average crystalline size increases from 37.3 to 50.6 nm for un-hydrogenated samples from x=0.03 to 0.05 and it changes from 29.4 to 34.9 nm for hydrogenated samples. The change in lattice parameters, micro-strain, a small shift of X-ray diffraction peaks towards lower angles and reduction in energy gap reveal the substitution of Cu²⁺ ions into Zn–Co–O lattice. The hydrogenation effect reduces the particle size and induces the more uniform distribution of particles than the un-hydrogenated samples which is confirmed by SEM micrographs. Photoluminescence spectra of Zn_0.96−xCo_0.04Cu_xO system shows that red shift in near band edge ultraviolet emission from 393 to 403 nm with suppressing intensity and a blue shift in green band emission from 537 to 529 nm with enhancing intensity confirms the substitution of Cu into the Zn–Co–O lattice.     

Influence of Mg content on optical properties of exciton confinement in wurtzite ZnO/MgxZn1−xO coupled quantum dots

Based on the framework of effective-mass approximation and variational approach, optical properties of exciton are investigated theoretically in ZnO/Mg_xZn_1−xO vertically coupled quantum dots (QDs), with considering the three-dimensional confinement of electron and hole pair and the strong built-in electric field effects. The exciton binding energy, the emission wavelength and the oscillator strength as functions of the structural parameters (the dot height, the barrier thickness between the coupled wurtzite ZnO QDs and Mg content x in the barrier layers) is calculated in detail. The results elucidate that Mg content have a significant influence on the exciton state and optical properties of ZnO coupled QDs. When Mg content x increases, the strong built-in electric field increases and leads to the redshift of the effective band gap of the Mg_xZn_1−xO layer. These theoretical results are useful for design and application of some important photoelectronic devices constructed by using ZnO strained QDs.     

Photoluminescence and excitation spectra of Cu(AlxGa1−x)S2 films grown by vapor phase epitaxy

Chalcopyrite Cu(Al_xGa_1−x)S₂ alloy films were successfully grown on GaP substrates by vapor phase epitaxy using metallic chlorides (CuCl, GaCl₃ and AlCl₃) and H₂S as source materials. Photoluminescence (PL) spectra of these films taken under a low excitation density using a super high pressure Hg lamp exhibited broad emissions in the orange region. Photoluminescence excitation (PLE) measurements revealed that these broad emissions are effectively excited at the photon energies of A- and the BC-exciton energies. Under the high excitation density using the pulsed XeCl laser, these alloy films showed the exciton related emissions composed of biexciton recombination, exciton-exciton and exciton-carrier scatterings. The influence of the compositional fluctuation was observed on the increase of the full-width at half maximum (FWHM) for the exciton related emission with increase in composition of x.     

Study on the electronic structure and optical properties of different Al constituent Ga1−xAlxAs

Using quantum mechanics GASTEP software package based on the first principle density function theory, the electronic structure and optical properties of Ga_1−xAl_xAs at different Al constituent are calculated. Result shows that with the increase of Al constituent, the band gap of Ga_1−xAl_xAs increases and varies from direct band gap to indirect band gap; the absorption band edge and the absorption peak move to high-energy side; the static reflectivity decreases. With the increasing of the incident photon energy, Ga_1−xAl_xAs shows metal reflective properties in certain energy range. With the increasing of Al constituent, static dielectric constant decreases and the intersection of dielectric function and the x-axis move towards high-energy side; the peak of energy loss function move to low-energy side and the peak value reduces.     

白宝石衬底上生长的MgxZn1-xO晶体薄膜的结构和光学性能

在白宝石（sapphire）衬底上低温外延生长出了Mg_xZn_1-xO晶体薄膜.x射线衍射（XRD）及能量色散x射线（EDX）分析表明，Mg_xZn_1-xO薄膜的晶体结构依赖于薄膜中Mg的组分x，随着Mg组分的增大，Mg_xZn_1-xO薄膜的结构从与ZnO晶体一致的六方结构转变为与MgO晶体一致的立方结构.对Mg_xZn_1-xO薄膜的紫外透 关键词： 电子束蒸发反应 xZn_1-xO晶体薄膜')" href="#">Mg_xZn_1-xO晶体薄膜 结构和光学性能