Synthesis of V O2(A) nanobelts by the transformation of V O2(B) under the hydrothermal treatment and its optical switching properties

V O₂(A) nanobelts had been successfully synthesized by the transformation of V O₂(B) using H₂O as the solvent under the hydrothermal approach at 280 °C for 48 h. Some parameters, such as the reaction temperature and time, had been briefly discussed to reveal the transition from V O₂(B) to V O₂(A). It was found that H₂O played a crucial role in the transition from V O₂(B) to V O₂(A). The phase transition of V O₂(A) nanobelts was at 162 °C. The optical switching properties of V O₂(A) were studied by the variable-temperature infrared spectra for the first time. In addition, V O₂(A) nanobelts were calcined at 700 °C for 2 h under a high purity Ar (99.999%) atmosphere to obtain V O₂(M) which exhibited a strong crystallographic transition at around 65 °C.     

Broadband infrared luminescence in Yb-doped Bi2O3–GeO2 glasses

The Yb-doped Bi₂O₃–GeO₂ glasses were prepared by the conventional melt quenching technique. Near-infrared (NIR) broadband emission was found at about 1024 nm, and 1330 nm (under 785 nm excitation), and the measured fluorescent lifetime was about several hundred microseconds. The emission intensity of Yb-doped Bi₂O₃–GeO₂ glasses increased with increasing of Yb dopant in our experiments. The NIR emission should be related to Yb³⁺ and lower valence Bi ions.     

Thermoluminescence and optically stimulated luminescence characteristics of Al2O3 doped with Tb

In the present work policrystals of α − Al₂O₃ doped with terbium were synthesized using the solvent evaporation method. The samples were prepared using Al(NO₃)₃·9H₂O and Tb(NO₃)₃·5H₂O reagents, with Tb concentrations between 1 and 5 mol% and thermally treated at high temperature above ∼1400 °C. X-ray diffraction measurements showed the α-phase formation of samples. TL glow curve presented an intense peak at ∼190 °C and two other with low intensity at 290 and 350 °C after gamma irradiation. The best doping concentration which presented high luminescence was the sample doped with 3 mol% of Tb. TL spectra and fluorescence measurements showed similar luminescence spectra with lines attribute to Tb³⁺ ions. A linear behavior to gamma dose between 1 and 20 Gy was observed in TL, using 190 °C peak as well as in OSL signal, this last carried out using 532 nm wavelength stimulation.     

氯化苯并咪唑镧的荧光光谱

对新合成的化合物氯化苯并咪唑镧HCl₄·[C₇H₆N₂(H₂O)₂]₂La及其LaCl₃·5H₂O的水溶液进行了三维荧光光谱测定,讨论了HCl₄·[C₇H₆N₂(H₂O)₂]₂La在不同波长的光激发下的荧光特性,荧光强度与浓度的关系及标题化合物的上转换荧光,即在540nm绿光的激发下可以获得紫外光(290nm)和近紫外光(360nm).     

Sono-assisted preparation of highly-efficient peroxidase-like Fe3O4 magnetic nanoparticles for catalytic removal of organic pollutants with H2O2

Fe₃O₄ magnetic nanoparticles (Fe₃O₄ MNPs) with much improved peroxidase-like activity were successfully prepared through an advanced reverse co-precipitation method under the assistance of ultrasound irradiation. The characterizations with XRD, BET and SEM indicated that the ultrasound irradiation in the preparation induced the production of Fe₃O₄ MNPs possessing smaller particle sizes (16.5 nm), greater BET surface area (82.5 m² g^?1) and much higher dispersibility in water. The particle sizes, BET surface area, chemical composition and then catalytic property of the Fe₃O₄ MNPs could be tailored by adjusting the initial concentration of ammonia water and the molar ratio of Fe²⁺/Fe³⁺ during the preparation process. The H₂O₂-activating ability of Fe₃O₄ MNPs was evaluated by using Rhodamine B (RhB) as a model compound of organic pollutants to be degraded. At pH 5.4 and temperature 40 °C, the sonochemically synthesized Fe₃O₄ MNPs were observed to be able to activate H₂O₂ and remove ca. 90% of RhB (0.02 mmol L^?1) in 60 min with a apparent rate constant of 0.034 min^?1 for the RhB degradation, being 12.6 folds of that (0.0027 min^?1) over the Fe₃O₄ MNPs prepared via a conventional reverse co-precipitation method. The mechanisms of the peroxidase-like catalysis with Fe₃O₄ MNPs were discussed to develop more efficient novel catalysts.     

Reductive Fluorescence Quenching of the Photoexcited Free Base <Emphasis Type="Italic">meso</Emphasis>-Tetrakis (Pentafluorophenyl) Porphyrin by Amines

Steady state and time resolved fluorescence quenching behaviors of meso-Tetrakis (pentafluorophenyl) porphyrin (H₂F₂₀TPP) in presence of different aliphatic and aromatic amines have been executed in homogeneous dichloromethane (DCM) solution. At room temperature in DCM, free base (H₂F₂₀TPP) shows fluorescence with two distinct peaks at 640 and 711 nm and natural lifetime τ _f = 9.8 ns which are very similar to that of meso-tetraphenyl porphyrin (TPP). Unlike TPP, addition of both aliphatic and aromatic amines to a solution containing H₂F₂₀TPP results in an efficient decrease in fluorescence intensity without altering the shape and peak position of fluorescence emission. Upon addition of amines there was no change in optical absorption spectra of H₂F₂₀TPP. The fluorescence quenching rate constants ranged from 1 × 10⁹ to 4 × 10⁹ s⁻¹, which are one order below to the diffusion control limit, and temperature dependent quenching rate constants yield the activation energies which are found to be order of 0.1 eV. Femto second transient absorption studies reveal the existence of amine cation radical and porphyrin anion radicals with very short decay time (15 ps). The fluorescence quenching reaction follows Stern–Volmer kinetics. Steady state and time-resolved data are interpreted within general kinetic scheme of Marcus semi-classical model which attributes bimolecular electron transfer process between amines and the lowest excited singlet state of H₂F₂₀TPP. Calculated internal reorganization energies are found to be in between 0.04 and 0.22 ev. Variation of electron transfer rate as function of free energy change (∆G⁰) points the ET reactions in the present systems are in Marcus normal region. This is the first example of reductive fluorescence quenching of free base neutral porphyrins in homogeneous organic solvent ever known.     

Synthesis and optical properties of Ce-doped Y3Mg2AlSi2O12 phosphors

Y_3−xMg₂AlSi₂O₁₂:Ce_x³⁺ (x=0.015, 0.03 and 0.06) phosphors possessing garnet crystal structure were synthesized by the sol–gel combustion technique. The samples were characterized by application of powder X-ray diffraction (XRD), photoluminescence (PL) spectroscopy, thermal quenching (TQ) and scanning electron microscopy (SEM). Moreover, luminous efficacies (LE), color points and quantum efficiencies (QE) were calculated. Optical properties were studied as a function of Ce³⁺ concentration and annealing temperature. XRD analysis revealed that sintering of polycrystalline Y₃Mg₂AlSi₂O₁₂:Ce³⁺ powders at 1550 °C results in nearly single-phase garnet materials. Phosphors showed broad emission band in the range of 500–750 nm and had the maximum intensity at 600 nm, which results in strongly red-shifted phosphors compared with conventional YAG:Ce phosphors emitting at 560 nm. However, strong concentration quenching has also been observed, probably due to increased Stokes shift.     

Search for new transparent conductors: Effect of Ge doping on the conductivity of Ga2O3, In2O3 and Ga1.4In0.6O3

Only a small amount (≤3.5 mol%) of Ge can be doped in Ga₂O₃, Ga_1.4In_0.6O₃ and In₂O₃ by means of solid state reactions at 1400 °C. All these samples are optically transparent in the visible range, but Ge-doped Ga₂O₃ and Ga_1.4In_0.6O₃ are insulating. Only Ge-doped In₂O₃ exhibits a significant decrease in resistivity, the resistivity decreasing further on thermal quenching and H₂ reduction. The resistivity of 2.7% Ge-doped In₂O₃ after H₂ reduction shows a metallic behavior, and a resistivity of ～1 mΩ cm at room temperature, comparable to that of Sn-doped In₂O₃.     

Oxygen sensing by fluorescence quenching of [Cu(btmgp)I]

A fluorescence study of acetonitrile solutions of bis(tetramethylguanidine)propane, copper(I)-iodide and [Cu(btmgp)I] was performed and the chemical reaction of the latter species with O₂ was investigated at room temperature. The actual quenching process via O₂ gassing was studied and an exponential dependence of the fluorescence intensity with respect to the complex concentration was observed.Furthermore the survey was deepened on time resolved fluorescence properties of solved [Cu(btmgp)I] in a wider concentration range. The applicability of this complex for O₂ sensing inside a microreactor system was proven by confocal fluorescence measurements. It was shown that the investigated system can be used for oxygen sensing in the copper concentration range from 10⁻² to 10⁻⁹ mol/l.     

NO Fluorescence Sensing by Europium Tetracyclines Complexes in the Presence of H2O2

The effect on the fluorescence of the europium:tetracycline (Eu:Tc), europium:oxytetracycline (Eu:OxyTc) and europium:chlortetracycline (Eu:ClTc) complexes in approximately 2:1 ratio of nitric oxide (NO), peroxynitrite (ONOO^?), hydrogen peroxide (H₂O₂) and superoxide (O₂ ^·?) was assessed at three ROS/RNS concentrations levels, 30 °C and pH 6.00, 7.00 and 8.00. Except for the NO, an enhancement of fluorescence intensity was observed at pH 7.00 for all the europium tetracyclines complexes—the high enhancement was observed for H₂O₂. The quenching of the fluorescence of the Tc complexes, without and with the presence of other ROS/RNS species, provoked by NO constituted the bases for an analytical strategy for NO detection. The quantification capability was evaluated in a NO donor and in a standard solution. Good quantification results were obtained with the Eu:Tc (3:1) and Eu:OxyTc (4:1) complexes in the presence of H₂O₂ 200 μM with a detection limit of about 3 μM (Eu:OxyTc).     

Dispersion behavior and thermal conductivity characteristics of Al2O3–H2O nanofluids

Nanofluid is a kind of new engineering material consisting of solid nanoparticles with sizes typically of 1–100 nm suspended in base fluids. In this study, Al₂O₃–H₂O nanofluids were synthesized, their dispersion behaviors and thermal conductivity in water were investigated under different pH values and different sodium dodecylbenzenesulfonate (SDBS) concentration. The sedimentation kinetics was determined by examining the absorbency of particle in solution. The zeta potential and particle size of the particles were measured and the Derjaguin–Landau–Verwey–Overbeek (DLVO) theory was used to calculate attractive and repulsive potentials. The thermal conductivity was measured by a hot disk thermal constants analyser. The results showed that the stability and thermal conductivity enhancements of Al₂O₃–H₂O nanofluids are highly dependent on pH values and different SDBS dispersant concentration of nano-suspensions, with an optimal pH value and SDBS concentration for the best dispersion behavior and the highest thermal conductivity. The absolute value of zeta potential and the absorbency of nano-Al₂O₃ suspensions with SDBS dispersant are higher at pH 8.0. The calculated DLVO interparticle interaction potentials verified the experimental results of the pH effect on the stability behavior. The Al₂O₃–H₂O nanofluids with an ounce of Al₂O₃ have noticeably higher thermal conductivity than the base fluid without nanoparticles, for Al₂O₃ nanoparticles at a weight fraction of 0.0015 (0.15 wt%), thermal conductivity was enhanced by up to 10.1%.     

Fluorophotometric Determination of Hydrogen Peroxide with Fluorescin in the Presence of Cobalt (II) and Reaction Against Other Reactive Oxygen Species

A fluorophotometric method for the determination of hydrogen peroxide (H₂O₂) using fluorescin was developed. This method was based on the oxidative reaction of fluorescin, a colorless, non-fluorescent lactoid fluorescein, by H₂O₂ to give highly fluorescein fluorescence emission. In the determination of H₂O₂, the calibration curve exhibited linearity over the H₂O₂ concentration range of 1.5–310 ng mL⁻¹ at an emission wavelength of 525 nm with an excitation of 500 nm and with relative standard deviations (n = 6) of 2.51%, 2.48%, and 1.31% for 3.1 ng mL⁻¹, 30.8 ng mL⁻¹, and for 308 ng mL⁻¹ of H₂O₂, respectively. The detection limit for H₂O₂ was 1.9 ng mL⁻¹ six blank determinations was performed (ρ = 6). This proposed method was applied to detection of other reactive oxygen species and nitrogen species (ROS/RNS) such as singlet oxygen (¹O₂), hydroxyl radical (^•OH), peroxynitrite (ONOO⁻) etc., and it was possible to detect them with a high sensitivity. In addition, this proposed method was applied to the recovery tests of H₂O₂ in calf serum, human saliva, rain water, and wheat noodles; the results were satisfactory.     

Spectroscopic characteristics of Tm3+ in Tm and Tm,Nd, Yb:Sc2O3 ceramic

The spectroscopic investigation of Tm³⁺ or (Nd, Yb, Tm)-doped Sc₂O₃ transparent ceramics, as laser-active media for visible and IR emission, was performed. The spectra are dominated by Tm³⁺ ions in sites of C₂ symmetry and an energy level scheme and other spectral parameters were determined. The strong concentration quenching of ³H₄ level emission in Tm:Sc₂O₃ at 300 K is discussed by considering the resonant cross-relaxation (³H₄→³F₄)?(³H₆→³F₄) process and multipolar interactions of various orders. The main energy-transfer processes leading to the blue upconversion emission from the ¹G₄ Tm³⁺ level in (Tm, Nd, Yb):Sc₂O₃ ceramic, under pulsed pumping at 808.3 nm were evidenced.     

Synthesis and characterization of V3O7⋅H2O nanobelts

V ₃O₇?H₂O nanobelts were prepared by a hydrothermal method at 190 ^°C using V ₂O₅?nH₂O gel and H₂C₂O₄?2H₂O as starting agents. The nanobelts obtained have diameters ranging from 40 to 70 nm with lengths of up to several micrometers. Their morphology and structure have been characterized by XRD, SEM, TEM and IR spectroscopy. The effect of the annealing temperature on the morphology of the resulting product has been investigated. XRD and SEM showed that thermal annealing of the V ₃O₇?H₂O sample in air led to the collapse of the V ₃O₇?H₂O nanobelt structure and the convert into V ₂O₅ nanobelts. For the first time V ₂O₅ nanobelts with an ultrahigh aspect-ratio have been obtained in air. Furthermore, electrical conductivity and static magnetic susceptibility measurements have been carried out.     

The influence of Eu3+ doping on photoluminescent properties of red emitting phosphor YInGe2O7:Eu3+ by microwave assisted and conventional sintering method

This paper describes an investigation of the crystalline morphology and photoluminescent properties of YInGe₂O₇ powders doped with different Eu³⁺ concentrations using microwave assisted sintering and conventional sintering. X-ray powder diffraction analysis confirmed the formation of monoclinic YInGe₂O₇ structure as YInGe₂O₇:Eu³⁺ powders were sintered at 1200 °C in microwave furnace for 1 h, and the raw material phase of Y₂O₃ was observed when Eu³⁺ concentration was below 30 mol%. Scanning electron microscopy showed microwave assisted sintering results in smaller particle size and more uniform grain size distribution. In the photoluminescent (PL) studies, the concentration quenching effect was observed under the excitation at 393 nm, but not under the excitation at CTS band. The ⁵D₀→⁷F₂ transition (620 nm), exhibits a non-exponential decay behavior as YInGe₂O₇:Eu³⁺ powders were sintered by microwave with the Eu³⁺ concentration higher than 50 mol%.     

Photoluminescence characteristics of ZnGa2O4 thin films prepared by chemical solution method

Zinc gallate (ZnGa₂O₄) thin film phosphors have been formed on ITO glass substrates by a chemical solution method with starting materials of zinc acetate dihydrate, gallium nitrate hydrate and 2-methoxiethanol as a solution. The thin films were firstly dried at 100 °C and fired at 500 °C for 30 min and then, annealed at 500 °C and 600 °C for 30 min under an annealing atmosphere of 3% H₂/Ar. XRD patterns of the thin film phosphors showed (311) and (220) peak indicating ZnGa₂O₄ crystalline phase in which all the (311) peaks of the film phosphors synthesized on ITO glass and soda-lime glass revealed high intensity with increasing annealing temperature from 500 °C to 600 °C. The ZnGa₂O₄ thin film phosphors represented marked change in AFM surface morphologies according to an annealing temperature under an annealing atmosphere (3% H2/Ar). The film phosphor, annealed at 600 °C, showed the embossed pattern with relatively regular spacing in AFM surface morphology. The ZnGa₂O₄ thin film phosphors formed on ITO glass, which were annealed at different temperatures and showed distinctive spectra with peak wavelengths of 434 nm and 436 nm in the blue emission region.     

Photocatalytic properties of lanthanide tungstates Ln2W2O9 (Ln=La,Pr, Nd,Sm, and Gd)

Lanthanide tungstates, Ln₂W₂O₉ (Ln=La, Pr, Nd, Sm, and Gd), were prepared via the polymerized complex method at 1273 K for 2 h, and their photocatalytic activities for hydrogen and oxygen evolution were investigated. Pt-loaded Gd₂W₂O₉ exhibited activity for H₂ evolution from an aqueous methanol solution under light irradiation (λ>300 nm). The remaining Ln₂W₂O₉ were inactive for H₂ evolution due to the influence of the Ln elements and their crystal structures. All Ln₂W₂O₉ were inactive for O₂ evolution from an aqueous AgNO₃ solution due to the lack of O₂ evolution sites on the surface.     

SrAl_2B_2O_7:Dy~(3+)材料的制备及其发光性能

采用高温固相法制备了SrAl2B2O7:Dy3+发光材料.在350nm紫外光激发下,测得SrAl2B2O7:Dy3+材料的发射光谱为一个多峰宽谱,主峰分别为480,573和678nm;分别和Dy3+的4F9/2→6H15/2,4F9/2→6H13/2,4F9/2→6H11/2的跃迁发射相对应;监测573nm的发射峰,得到材料的激发光谱为一个多峰宽谱,主峰分别为295,325,350,365,400nm.研究了Dy3+掺杂浓度对SrAl2B2O7:Dy3+材料发射光谱的影响,随着Dy3+掺杂浓度的增大,SrAl2B2O7:Dy3+材料的Iy/Ib逐渐增大,根据Judd-Ofelt理论解释了其原因.随着Dy3+掺杂浓度的增大,Dy3+的4F9/2→6H13/2跃迁产生的573nm发射峰强度先增大,在4%时达到最大值,之后减小,其自身的浓度猝灭机理为电偶极-电偶极相互作用.不同的电荷补偿剂Li+,Na+,K+的引入均使发光强度得到提高,尤其以Li+最佳,发光强度提高了大约33%.     

Synthesis and luminescence properties of green phosphors Ca6Sr4(Si2O7)3Cl2:Eu2+ for white light emitting diodes

Divalent europium-activated chlorosilicate Ca₆Sr₄(Si₂O₇)₃Cl₂:Eu²⁺ phosphors were synthesized by a conventional solid-state reaction under reductive atmosphere. These phosphors can be efficiently excited by UV–visible light from 320 to 420 nm, which matches that of a near UV-emitting InGaN chip. Under the 360 nm excitation, Ca₆Sr_3.97(Si₂O₇)₃Cl₂:0.03Eu²⁺ phosphor shows a strong and broad emission centering at 515 nm, which is attributed to the 5d→4f transition of Eu²⁺ ion. The mechanism of concentration quenching was determined to be the dipole–dipole interaction and the critical energy-transfer distance of Eu²⁺ was calculated as 3.31 nm. The CIE chromaticity coordinates of Ca₆Sr_3.96(Si₂O₇)₃Cl₂:0.03Eu²⁺ phosphor are (0.127, 0.770) according to the emission spectrum. It can be expected that Ca₆Sr₄(Si₂O₇)₃Cl₂:Eu²⁺ phosphor is a promising candidate as the green component for near-ultraviolet InGaN-based white LED.     

Synthesis and luminescence properties of a broad-band red phosphor Ca3Si2O7:Eu2+ for warm white light-emitting diodes

Single-phase broad-band red-emitting Ca₃Si₂O₇:Eu²⁺ phosphors, with photoluminescence features that qualify them as candidates for white light-emitting diodes applications, were successfully synthesized via a modified solid-state reaction method that employed H₃BO₃ as a flux. The phosphors produced have an intense broad red emission band, with a peak at 603 nm, a full width at half maximum of 110 nm, and color coordinates of (0.550, 0.438). Concentration quenching occurred at 0.01 mol Eu²⁺. The discussion of the results shows that Eu²⁺ ions should be accommodated at the Ca-sites of the lattice, dipole–dipole interactions should predominantly govern the energy transfer mechanism among them, and the critical distance between them is ～31 Å.