不同改性剂对聚丙烯/碳酸钙复合材料性能的影响

以马来酸酐(MAH)、聚丙烯蜡(PPW)为主要原料,采用原位固相接枝改性法制得PP/CaCO3-MAH-PPW复合材料,并与添加相容剂聚丙烯接枝马来酸酐(PP-g-MAH)所制得的PP/PP-g-MAH/CaCO3复合材料进行比较。结果表明,CaCO3良好的分散性及其与PP基体适宜的界面粘接是复合材料具有较好韧性的关键因素。与PP/PP-g-MAH/CaCO3复合材料相比,PP/CaCO3-MAH-PPW复合材料表现出更佳的冲击、弯曲和加工性能,当m(PP)∶m(CaCO3)=100∶20时,材料缺口冲击强度达到最大值,是基体树脂的1.19倍。     

PP-g-(MAH/St)和PP-g-MAH对聚丙烯/木粉复合材料性能的影响

在转矩流变仪中用熔融接枝法制备马来酸酐(MAH)和苯乙烯(St)接枝聚丙烯（PP）-PP-g-(MAH/St)和PP-g-MAH,将其作为聚丙烯/木粉复合材料的相容剂。 FTIR证实MAH和St单体与PP发生接枝反应。 用SEM和DSC等手段考察两种相容剂对PP/木粉复合材料微观形貌和结晶性能的影响,探索了各种PP/木粉复合材料加工和力学性能不同的内在原因。 SEM显示,PP-g-(MAH/St)改性木粉比PP-g-MAH改性木粉在PP基体中分散性更佳,木粉与PP的界面更加模糊,相容性进一步改善。 DSC结果表明,PP-g-(MAH/St)改性体系可增强木粉对PP的异相成核作用,提高结晶温度和结晶度。 复合材料的加工和力学性能测试结果表明,PP-g-(MAH/St)改性效果明显优于PP-g-MAH。 复合材料的熔体质量流动速率随相容剂用量的增加而逐步下降,PP-g-(MAH/St)改性体系拉伸强度和弯曲强度却逐步上升,并在相容剂用量为4.8 g/100 g PP时达到极值。 此时其拉伸强度达40.62 MPa,分别是未改性体系和PP-g-MAH改性体系的1.29和1.17倍;其弯曲强度达45.72 MPa,分别是未改性体系和PP-g-MAH改性体系的1.23和1.59倍;而无缺口冲击强度却在相容剂用量为3.6 g/100 g PP时达到极值13.35 kJ/m2,分别是未改性体系和PP-g-MAH改性体系的1.62倍和1.42倍。     

聚丙烯表面光氧化的XPS研究

利用X射线光电子能谱(XPS)研究了光氧老化的聚丙烯(PP)表面的化学结构和组成变化。结果表明:(1)在受光氧老化的PP表面上形成了C-O、C=O及O-C=O官能团;(2)低分子抗氧剂在PP表面发生富集;(3)表面Ols/Cls强度比率可以较好地与冲击强度保留率相关联。     

纳米CaCO_3/相容剂/PP中的界面相互作用研究

采用不同相容剂(PP-g-MAH、POE-g-MAH和EVA-g-MAH)制备了不同界面相互作用的纳米CaCO3(CC)/相容剂/PP体系,研究了相容剂/PP和相容剂/CC界面相互作用对PP/CC的结晶形态、结晶行为、熔融特性和力学性能的影响.观察到PP/CC界面相互作用提高PP结晶温度和PP/CC的模量和冲击强度,但降低了屈服强度.相容剂/CC界面相互作用进一步提高了PP/CC的结晶温度.PP/相容剂界面相互作用取决于PP与相容剂相容性.PP/PP-g-MAH相容性高有利于提高PP/CC的异相成核作用和PP/CC屈服强度和模量,但降低冲击强度.PP/POE-g-MAH部分相容对相容剂/CC界面的异相成核作用、PP/CC屈服强度和模量影响不大,可明显提高冲击强度.但PP/EVA-g-MAH不相容导致PP/CC冲击强度明显降低.     

双梳型共聚物在莠去津颗粒表面吸附的X射线光电子能谱分析

采用X射线光电子能谱(XPS)研究了双梳型共聚物吸附于莠去津颗粒样品表面的电子状态,计算了吸附厚度.结果表明:吸附后,莠去津颗粒界面的N 1s和Cl 2p谱峰强度明显减弱,Cl 2s几乎消失,而C 1s和O1s谱峰强度则明显增强,这主要是双梳型共聚物中C和O的贡献,且吸附后能在莠去津颗粒界面形成良好的吸附保护膜,其厚度...     

超支化聚乙烯亚胺接枝二氧化硅的制备及在聚丙烯改性中的应用

首先利用3-缩水甘油氧基丙基三甲氧基硅烷(简称GPS)作为偶联剂,对纳米SiO2进行表面改性,获得表面含有环氧基的SiO2纳米粒子(SiO2-GPS).利用这些环氧基与超支化聚乙烯亚胺(HPEI)分子中的氨基进行反应,得到SiO2接枝超支化聚乙烯亚胺的纳米粒子(SiO2-GPS-g-HPEI).然后利用SiO2-GPS-g-HPEI与聚丙烯(PP)和PP接枝的马来酸酐(PP-g-MAH)共混、模压,制备PP/SiO2-GPS-g-HPEI/PP-g-MAH复合材料.红外光谱测试和热失重分析(TGA)测试结果表明,SiO2纳米粒子表面依次接枝了GPS和HPEI;扫描电子显微镜(SEM)的测试结果显示,SiO2-GPS-g-HPEI在聚丙烯基体中分散良好,其材料的冲击断裂为韧性断裂;复合材料共混时,扭矩的增加证明了共混物中分散相(SiO2-GPS-g-HPEI)与基体(PP/PP-g-MAH)界面之间存在一定的相互作用.少量SiO2-GPS-g-HPEI加入PP/PP-g-MAH中,冲击强度可增加96.3%,拉伸强度也有较大的提高.     

聚丙烯/硫酸钡复合体系的界面相互作用与流变性质和结晶行为的关系

制备了一系列具有不同界面状态的聚丙烯 (PP) 硫酸钡 (BaSO4)复合体 .PP BaSO4的界面分别用硅烷、硬脂酸、马来酸酐接枝聚丙烯 (PP g MAH)改性 .研究表明 ,填充体系的熔体粘度和熔体弹性均高于基体 .以硅烷和PP g MAH进行界面改性后 ,PP BaSO4的界面相互作用加强 ,导致复合体系中的熔体粘度和熔体弹性进一步提高 ,同时BaSO4对PP的成核活性提高 .填料用硬脂酸处理后 ,硬脂酸能够在填料粒子表面上形成一个包覆层 ,使粒子与PP的亲和性改善 .同时该包覆层具有润滑作用 ,使得复合体系的熔体粘度和熔体弹性下降 ,并使得该体系中BaSO4的成核活性低于硅烷和处理的体系 .本文探讨了由复合体系的熔体粘度定量比较填充复合体系中聚合物 填料界面相互作用的方法 ,讨论了界面改性对复合体系流变性质和结晶行为影响的机理     

氧化铝薄膜表面羰基钼物种的可逆再生

 通过Mo(CO)6的热分解制备了Al2O3薄膜负载的金属钼模型催化剂,并采用热脱附谱(TDS)和X射线光电子能谱(XPS)原位研究了CO在金属态Mo/Al2O3模型催化剂表面的化学吸附. 结果表明,在低温下CO可与Al2O3表面的金属钼纳米粒子发生多重配位形成类似于羰基钼的物种. CO在Mo/Al2O3模型催化剂表面的吸附导致Mo 3d XPS峰向高结合能方向位移,所生成的羰基钼物种表现为TDS谱中在240 K处有脱附峰. 负载的金属钼模型表面与体相金属钼的化学性质完全不同,表现出明显的粒子尺寸效应.     

PP—g—（GMA—co—St）对PA6—PC共混合的反应增容作用

用红外、扫描电镜、熔体流动速率和力学性能等测试方法,研究了甲基丙烯酸缩水甘油酯（GMA）和苯乙烯（St）多单体熔融接枝聚丙烯PP－g-(GMA-co-St)对PA6－PC共混合的反应增容作用。研究结果表明,在熔融共混过程中,PP－g-(GMA-co-St)中的环氧基与PA6的端氨基及PC的端羟基原位生成的接枝共聚物就有效地降低了共混物相间的界面张力,明显提高了共混物相界面的粘着力。少量的PP－g-(GMA-co-St)就能使PA6和PC的相容性得到显著改善。当PP－g-(GMA-co-St)的质量分数为10％时,共混物分散相的相区尺寸细化到0．2μm,其力学性能也有较大提高。PA6／PC／PP－g-(GMA-co-St)共混物的力学性能均衡,达到了弹性体增韧体系难以达到的效果。即使PP－g-(GMA-co-St)组分含量为20％时,共混物仍能保持较好的力学性能,特别是在共混物地韧性得以提高的同时,其强度和伸长率也提高。     

羟基不饱和脂肪酸改性纳米碳酸钙对聚丙烯微观形态和流变性能的影响

采用羟基不饱和脂肪酸,通过固相法对硬脂酸改性的工业纳米碳酸钙CCR进行表面改性制备了R-CCR,红外光谱(FTIR)显示改性剂已结合在碳酸钙表面.通过熔融共混法制备了聚丙烯(PP)/乙丙橡胶(EPDM)/纳米碳酸钙二元和三元复合材料.并利用扫描电子显微镜(SEM)和透射电子显微镜(TEM)观察复合材料的微观形态,发现R-CCR的加入,使PP复合材料的拉伸断面出现明显的拉丝状结构和大面积的屈服变形,与PP/EPDM/CCR相比,PP/EPDM/R-CCR冲击断面的空穴明显增加并细化,R-CCR在PP基体中分散均匀,且界面模糊,与基体的相容性明显优于CCR.复合材料流变行为的研究表明R-CCR的加入,体系储存模量G′和损耗模量G″随频率的增加而增加,对损耗因子和复数粘度的影响不大;但PP/EPDM/R-CCR复合材料的表观粘度,明显低于PP/EPDM/CCR和纯PP,同时,剪切速率的增加可有效降低体系的表观粘度.力学性能表明,R-CCR对PP同时起到增韧和增强的效果.且R-CCR和EPDM对PP具有协同增韧的效果.在保持聚丙烯的模量和强度基本不变的前提下,大幅度的改善聚丙烯的韧性,同时加工性能保持不变.     

Effects of different compatibilizing agents on the interfacial adhesion properties of polypropylene/magnesium oxysulfate whisker composites

The effects of maleic anhydride-grafted polypropylene(PP-g-MAH) and maleic anhydride-grafted polyolefin elastomer(POE-g-MAH) on interfacial adhesion properties of the polypropylene/magnesium oxysulfate whiskers(PP/MOSw) composites were investigated via mechanical, thermal, ATR-FTIR and rheological tests. Although significant increases in yield strength and Young's modulus were observed in PP-g-MAH treated composites, a sharp decline in these properties was observed in POE-g-MAH treated composites. ATR-FTIR results indicated that esterification occurred between the hydroxyl groups of MOSw and the carbonyls of anhydrides of both compatibilizers but POE-g-MAH was still incompatible with the PP matrix, as verified by the presence of shoulder peaks in DTG curves and numerous voids in SEM micrographs. On the other hand, PP-g-MAH was highly compatible with the PP matrix, as evidenced by the peaks in DTG curves and vague interfaces with wrapped melts on the surface of MOSw. Rheological behaviors also confirmed that introducing PP-g-MAH resulted in a transition from liquid-like to solid-like, which was attributed to the stronger interfacial adhesion between MOSw and the PP matrix. POE-g-MAH treated composites, in contrast to PP-g-MAH, maintained liquidlike rheological behaviors as typical molten polymers. There is likely a MOSw network formed in the PP/15PP-gMAH/15 MOSw composite as suggested by the significant deviation of G′ versus G″ plots and the two crossover frequencies observed in plots of tan? versus frequency.     

PP-g-MAH对聚丙烯/滑石粉复合材料的性能影响

研究了两种马来酸酐接枝聚丙烯（PP-g-MAH）在不同含量时对聚丙烯（PP）/滑石粉复合材料的力学性能、雾化性能和线性膨胀系数的影响.结果表明,接枝物的加入能提高复合材料的拉伸性能、冲击性能和弯曲性能,但随着含量的增加拉伸强度、冲击强度和弯曲强度及弯曲模量有所降低.在含量相同时,接枝物1对冷凝组份的影响更小.复合材料的线性膨胀系数随接枝物含量的增加先减小后增加.     

增容剂对聚对苯二甲酸乙二酯/聚丙烯共混体系结构流变学的影响

采用马来酸酐接枝聚丙烯(PP-g-MAH)对聚丙烯/聚对苯二甲酸乙二酯(PP/PET)共混体系进行增容,研究了增容前后复合体系的相形态和流变行为的变化.结果表明,共混体系中当PP组分为分散相时,增容剂能够显著减小PP液滴尺寸,使其形状松弛时间减小,变形与破裂的剪切敏感性降低;当共混体系两组分配比处于临界相反转点周围时,增容剂则会导致其内部部分双连续与“海-岛”结构共存的复杂相形态消失,低频区模量频率依赖性的增加表明体系内部界面结合程度的增加;而当共混体系中的PET组分为分散相时,增容剂的引入对体系结构流变学影响较小,表明增容效果不大.     

可膨胀石墨阻燃体系在聚丙烯中的作用

采用可膨胀石墨(EG)为主阻燃剂,包裹红磷(MRP)为阻燃协效剂制备阻燃聚丙烯(PP)。在mEG∶mMRP≥2时,阻燃效果最佳。阻燃剂(FR)含量达到30%后,阻燃效果大幅度提高,氧指数大于28。采用热失重和流变学方法分析了炭层质量,探讨了在mEG∶mMRP≥2时,阻燃效率最高的原因。相容剂马来酸酐接枝聚丙烯(PP-g-MAH)能够改善阻燃剂和聚丙烯之间的相容性,提高粘结力,改善炭层质量,提高材料的氧指数,PP-g-MAH用量为30%时,材料的氧指数达到31.4。     

Preparation and crystallization behaviour of PP/PP-g-MAH/Org-MMT nanocomposite

The melt-direct intercalation method was employed to prepare polypropylene (PP)/maleic anhydride grafted polypropylene (PP-g-MAH)/organic-montmorillonite (Org-MMT), X-ray diffractometer was used to investigate the intercalation effect and crystallite size in composites and TEM micrograph to observe the dispersion of Org-MMT interlayers in polypropylene. The results showed that by introducing maleated polypropylene in PP/Org-MMT composite, macromolecule segments had intercalated into interlayer space of Org-MMT. As a result, Org-MMT interlayers were dispersed evenly in polypropylene and PP/PP-g-MAH/Org-MMT nanocomposite was synthesized. The crystallite size of nanocomposite perpendicular to the crystalline plane such as (0 4 0), (1 3 0), (1 1 1), (0 4 1) is smaller than that of pristine PP, which indicated that the crystallite size of PP in nanocomposite can be diminished by adding PP-g-MAH and Org-MMT in PP. Moreover, the nonisothermal crystallization kinetics of PP and PP/PP-g-MAH/Org-MMT nanocomposite was investigated by differential scanning calorimetry (DSC) with various cooling rates. The Avrami analysis modified by Jeziorny, Ozawa method and a method developed by Liu were employed to describe the nonisothermal crystallization process of these samples. The difference in the exponent n between PP and nanocomposite, indicated that nonisothermal kinetic crystallization corresponded to tridimensional growth with heterogeneous nucleation. The values of half-time, Z_c, F(T) and K(T) showed that the crystallization rate of composites was faster than that of PP at a given cooling rate.     

Mechanism of adhesion promotion between aluminium sheet and polypropylene with maleic anhydride‐grafted polypropylene by γ‐aminopropyltriethoxy silane

The effect of concentration of γ‐aminopropyltriethoxy (γ‐APS) solution on shear strength of adhesive bonding between aluminium sheet and polypropylene (PP) with addition of a certain amount of maleic anhydride‐grafted polypropylene (PP‐g‐MAH) has been investigated. It is shown that the lap shear strength is promoted obviously with pre‐treatment of aluminium sheet by γ‐APS. The maximum strength is obtained at a concentration of 3% γ‐APS solution. With further high concentration of γ‐APS, the lap shear strength decreases. The examination of the separated surfaces by X‐ray photoelectron spectroscopy (XPS) shows that (C?O)₂? O? Al and C(?O)? O? Al are formed for adhesive bonding between PP with the addition of 20 wt% PP‐g‐MAH and aluminium sheet without pre‐treatment by γ‐APS, and that the area ratio of C related to oxygen on the separated aluminium side is 33.28%, which is obviously higher than 14% on the polymer side. As for adhesive bonding between PP with the addition of 20% PP‐g‐MAH and 3% γ‐APS pre‐treated aluminium sheet, C(?O)? N? C(?O) and C(?O)? NH are formed. The area ratio of C related to oxygen on the separated polymer side increases to 24.99%. It is proposed that γ‐APS pre‐treatment improves the distribution and shape of PP‐g‐MAH chains in the region adsorbed on the substrate and the region adjacent to this region. The chemical interactions at the interface are also proposed. Copyright © 2008 John Wiley & Sons, Ltd.     

Atomic force microscopy study on blend morphology and clay dispersion in polyamide‐6/polypropylene/organoclay systems

The phase structure and clay dispersion in polyamide‐6(PA6)/polypropylene(PP)/organoclay (70/30/4) systems with and without an additional 5 parts of maleated polypropylene (MAH‐g‐PP) as a compatibilizer were studied with atomic force microscopy (AFM). AFM scans were taken from the polished surface of specimens that were chemically and physically etched with formic acid and argon ion bombardment, respectively. The latter technique proved to be very sensitive to the blend morphology, as PP was far more resistant to ion bombardment than PA6. In the absence of the MAH‐g‐PP compatibilizer, the organoclay is located in the PA6 phase; this finding is in line with transmission electron microscopic results. Further, the PP is coarsely dispersed in PA6 and the adhesion between PA6 and PP is poor. The addition of MAH‐g‐PP resulted in a markedly finer PP dispersion and good interfacial bonding between PA6 and PP. In this blend, the organoclay was likely dispersed in the PA6‐grafted PP phase. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43:1198–1204, 2005     

低乙烯含量共聚聚丙烯链结构和相结构与应力应变行为的关系

研究了两种典型的低温抗冲共聚聚丙烯(ICPP)的应力应变行为及温度依赖性,其低温应力应变行为揭示ICPP具有优异的低温抗冲性能和综合力学性能的结构本质.从初始弹性模量、屈服应力及断裂伸长随温度变化所显示的变化规律进一步确认了两种ICPP的序列结构特征和相结构特征.断裂伸长变化显示了乙丙橡胶相的增韧作用,屈服应力变化显示了分散相对基质结合紧密程度的影响,弹性模量则与基质的结晶状况和结晶形态有着比较密切的关系,同时也与乙丙橡胶相和聚丙烯基质的玻璃化转变温度密切相关.