Validation of a direct non-destructive quantitative analysis of amiodarone hydrochloride in Angoron formulations using FT-Raman spectroscopy

Raman spectroscopy was applied for the direct non-destructive analysis of amiodarone hydrochloride (ADH), the active ingredient of the liquid formulation Angoron^®. The FT-Raman spectra were obtained through the un-broken as-received ampoules of Angoron^®. Using the most intense vibration of the active pharmaceutical ingredient (API) at 1568 cm⁻¹, a calibration model, based on solutions with known concentrations, was developed. The model was applied to the Raman spectra recorded from three as-purchased commercial formulations of Angoron^® having nominal strength of 50 mg ml⁻¹ ADH. The average value of the API in these samples was found to be 48.56 ± 0.64 mg ml⁻¹ while the detection limit of the proposed technique was found to be 2.11 mg ml⁻¹. The results were compared to those obtained from the application of HPLC using the methodology described in the European Pharmacopoeia and found to be in excellent agreement. The proposed analytical methodology was also validated by evaluating the linearity of the calibration line as well as its accuracy and precision. The main advantage of Raman spectroscopy over HPLC method during routine analysis is that it is considerably faster and no solvent consuming. Furthermore, Raman spectroscopy is non-destructive for the sample. However, the detection limit for Raman spectroscopy is much higher than the corresponding for the HPLC methodology.     

The effect of spatial confinement of Nafion in porous membranes on macroscopic properties of the membrane

Polyelectrolytes were incorporated into porous reinforcing materials to study the properties of ionomers in confined spaces and to determine the effect of the porous material on the behaviour of the membranes. Nafion^® was imbibed into porous polypropylene (Celgard^®), ultra-high-molecular weight polyethylene (Daramic^®), and polytetrafluoroethylene (PTFE) films. Through the use of reinforcing materials, it is possible to prepare membranes that are thinner, but stronger than pure ionomer membranes. Thin reinforced membranes have advantages such as lower areal resistance (as low as 0.14 Ω cm² for 57 μm CG3501 + Nafion^® compared to 0.34 Ω cm² for 89 μm cast Nafion^®) and lower dimensional changes due to swelling (as low as a 4% change in length and width for WDM + Nafion^® compared to 13% for cast Nafion^®). Using reinforcing materials results in a reduction in important membrane properties compared to bulk Nafion^®, such as proton conductivity (as low as 0.016 S cm⁻¹ for CG3401 + Nafion^® compared to 0.076 S cm⁻¹ for cast Nafion^®), effective proton mobility (as low as 3.2 × 10⁻⁴ cm² V⁻¹ s⁻¹ CG3401 + Nafion^® compared to 7.6 × 10⁻⁴ cm² V⁻¹ s⁻¹ for cast Nafion^®), and water vapour permeance (as low as 0.036 g h⁻¹ Pa⁻¹ m⁻² for WDM + Nafion^® compared to 0.056 g h⁻¹ Pa⁻¹ m⁻² for cast Nafion^®). By normalizing the membrane properties with respect to ionomer content, it was possible to examine the properties of the Nafion^® inside the pores of the membranes. The proton conductivity (as low as 0.032 S cm⁻¹ for CG3401 + Nafion^®), effective proton mobility (as low as 3.6 × 10⁻⁴ cm² V⁻¹ s⁻¹ for CG3401 + Nafion^®), and water vapour permeability (as low as 2.7 × 10⁻⁶ g h⁻¹ Pa⁻¹ m⁻¹ for PTFE MP 0.1 + Nafion^®) of the ionomer in the membrane are also diminished compared to bulk Nafion^® due to decreased connectivity of the ionomer and a restriction in macromolecular motions caused by the pore walls. A series of porous materials with increasing pore were also examined. As the pore size of the PTFE MP materials increased from 0.1 μm to 10 μm, the proton conductivity (0.022 S cm⁻¹ to 0.041 S cm⁻¹), effective proton mobility ((4.1 to 5.6) × 10⁻⁴ cm² V⁻¹ s⁻¹), and water vapour permeability ((2.4 to 4.3) × 10⁻⁶ g h⁻¹ Pa⁻¹ m⁻¹) of the reinforced membranes improved with increasing pore size and the properties of the ionomer inside the membranes approached the value of bulk Nafion^®.     

Evaluation of diffusive gradients in thin-films using a Diphonix resin for monitoring dissolved uranium in natural waters

Commercially available Diphonix^® resin (TrisKem International) was evaluated as a receiving phase for use with the diffusive gradients in thin-films (DGT) passive sampler for measuring uranium. This resin has a high partition coefficient for actinides and is used in the nuclear industry. Other resins used as receiving phases with DGT for measuring uranium have been prone to saturation and significant chemical interferences. The performance of the device was evaluated in the laboratory and in field trials. In laboratory experiments uptake of uranium (all 100% efficiency) by the resin was unaffected by varying pH (4–9), ionic strength (0.01–1.00 M, as NaNO₃) and varying aqueous concentrations of Ca²⁺ (100–500 mg L⁻¹) and HCO₃⁻ (100–500 mg L⁻¹). Due to the high partition coefficient of Diphonex^®, several elution techniques for uranium were evaluated. The optimal eluent mixture was 1 M NaOH/1 M H₂O₂, eluting 90% of the uranium from the resin. Uptake of uranium was linear (R² = 0.99) over time (5 days) in laboratory experiments using artificial freshwater showing no saturation effects of the resin. In field deployments (River Lambourn, UK) the devices quantitatively accumulated uranium for up to 7 days. In both studies uptake of uranium matched that theoretically predicted for the DGT. Similar experiments in seawater did not follow the DGT theoretical uptake and the Diphonix^® appeared to be capacity limited and also affected by matrix interferences. Isotopes of uranium (U²³⁵/U²³⁸) were measured in both environments with a precision and accuracy of 1.6–2.2% and 1.2–1.4%, respectively. This initial study shows the potential of using Diphonix^®-DGT for monitoring of uranium in the aquatic environment.     

Calibration and use of the Chemcatcher passive sampler for monitoring organotin compounds in water

An integrative passive sampler (Chemcatcher^®) consisting of a 47 mm C₁₈ Empore™ disk as the receiving phase overlaid with a thin cellulose acetate diffusion membrane was developed and calibrated for the measurement of time-weighted average water concentrations of organotin compounds [monobutyltin (MBT), dibutyltin (DBT), tributlytin (TBT) and triphenyltin (TPhT)] in water. The effect of water temperature and turbulence on the uptake rate of these analytes was evaluated in the laboratory using a flow-through tank. Uptake was linear over a 14-day period being in the range: MBT (3-23 mL day⁻¹), DBT (40-200 mL day⁻¹), TBT (30-200 mL day⁻¹) and TPhT (30-190 mL day⁻¹) for all the different conditions tested. These sampling rates were high enough to permit the use of the Chemcatcher^® to monitor levels of organotin compounds typically found in polluted aquatic environments. Using gas chromatography (GC) with either ICP-MS or flame photometric detection, limits of detection for the device (14-day deployment) for the different organotin compounds in water were in the range of 0.2-7.5 ng L⁻¹, and once accumulated in the receiving phase the compounds were stable over prolonged periods. Due to anisotropic exchange kinetics, performance reference compounds could not be used with this passive sampling system to compensate for changes in sampling rate due to variations in water temperature, turbulence and biofouling of the surface of the diffusion membrane during field deployments. The performance of the Chemcatcher^® was evaluated alongside spot water sampling in Alicante Habour, Spain which is known to contain elevated levels of organotin compounds. The samplers provided time-weighted average concentrations of the bioavailable fractions of the tin compounds where environmental concentrations fluctuated markedly in time.     

A highly sensitive amperometric sensor for oxygen based on iron(II) tetrasulfonated phthalocyanine and iron(III) tetra-(N-methyl-pyridyl)-porphyrin multilayers

The development of a highly sensitive sensor for oxygen is proposed using a glassy carbon (GC) electrode modified with alternated layers of iron(II) tetrasulfonated phthalocyanine (FeTsPc) and iron(III) tetra-(N-methyl-pyridyl)-porphyrin (FeT4MPyP). The modified electrode showed excellent catalytic activity for the oxygen reduction. The reduction potential of the oxygen was shifted about 330 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare GC electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves 4 electrons with a heterogenous rate constant (k_obs) of 3 × 10⁵ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.4 mg L⁻¹, with a sensitivity of 4.12 μA L mg⁻¹ (or 20.65 μA cm⁻² L mg⁻¹) and a detection limit of 0.06 mg L⁻¹ were obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation (R.S.D.) was 2.0% for 10 measurements of a solution of 6.4 mg L⁻¹ oxygen. The sensor was applied to determine oxygen in pond and tap water samples showing to be a promising tool for this purpose.     

Electrospun nanofiber based colorimetric probe for rapid detection of Fe in water

An imidazole derivative, 2-(2′-pyridyl)imidazole (PIMH), was developed as a colorimetric probe for the qualitative analysis of Fe²⁺ in aqueous solution. PIMH was then used to post-functionalize poly(vinylbenzyl chloride) (PVBC) nanofibers after electrospinning so as to afford a solid state colorimetric probe. Upon treatment with Fe²⁺ the probe displayed a distinctive color change both in liquid and solid platforms. The linear dynamic range for the colorimetric determination of Fe²⁺ was 0.0988–3.5 μg mL⁻¹. The ligand showed a high chromogenic selectivity for Fe²⁺ over other cations with a detection limit of 0.102 μg mL⁻¹ in solution (lower than the WHO drinking water guideline limit of 2 mg L⁻¹), and 2 μg mL⁻¹ in the solid state. The concentration of Fe²⁺ in a certified reference material (Iron, Ferrous, 1072) was found to be 2.39 ± 0.01 mg L⁻¹, which was comparable with the certified value of 2.44 ± 0.12 mg L⁻¹. Application of the probe to real samples spiked with Fe²⁺ achieved recoveries of over 97% confirming accuracy of the method and its potential for on-site monitoring.     

Tetradecyl(trihexyl)phosphonium chloride ionic liquid single-drop microextraction for electrothermal atomic absorption spectrometric determination of lead in water samples

A highly efficient single-drop microextraction (SDME) procedure using a low-cost room temperature ionic liquid (RTIL), i.e., tetradecyl(trihexyl)phosphonium chloride (CYPHOS^® IL 101), for Pb determination at trace levels in real water samples was developed. Lead was chelated with 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (5-Br-PADAP) reagent and extracted into a 4 μL microdrop of CYPHOS^® IL 101. The RTIL drop was directly injected into the graphite furnace of the electrothermal atomic absorption spectrometer (ETAAS). Under optimal microextraction conditions, a preconcentration factor of 32 was achieved with only 1.5 mL of sample resulting in a phase-volume ratio of 375. The limit of detection (LOD) obtained was 3.2 ng L⁻¹ and the relative standard deviation (RSD) for 10 replicates at 0.5 μg L⁻¹ Pb²⁺ concentration level was 4.9%, calculated at peak heights. The calibration graph was linear from concentration levels near the detection limits up to at least 4.5 μg L⁻¹ with a correlation coefficient of 0.9996. The accuracy of the methodology was evaluated by analysis of a certified reference material (CRM). The method was successfully applied to the determination of Pb in tap, mineral, well and river water samples.     

Biosensors for determination of glucose with glucose oxidase immobilized on an eggshell membrane

A glucose biosensor using an enzyme-immobilized eggshell membrane and oxygen electrode for glucose determination has been fabricated. Glucose oxidase was covalently immobilized on an eggshell membrane with glutaraldehyde as a cross-linking agent. The glucose biosensor was fabricated by positioning the enzyme-immobilized eggshell membrane on the surface of a dissolved oxygen sensor. The detection scheme was based on the depletion of dissolved oxygen content upon exposure to glucose solution and the decrease in the oxygen level was monitored and related to the glucose concentration. The effect of glutaraldehyde concentration, pH, phosphate buffer concentration and temperature on the response of the glucose biosensor has been studied in detail. Common matrix interferents such as ethanol, d-fructose, citric acid, sodium benzoate, sucrose and l-ascorbic acid did not give significant interference. The resulting sensor exhibited a fast response (100 s), high sensitivity (8.3409 mg L⁻¹ oxygen depletion/mmol L⁻¹ glucose) and good storage stability (85.2% of its initial sensitivity after 4 months). The linear response is 1.0×10⁻⁵ to 1.3×10⁻³ mol L⁻¹ glucose. The glucose content in real samples such as commercial glucose injection preparations and wines was determined, and the results were comparable to the values obtained from a commercial glucose assay kit based on a spectrophotometric method.     

Determination of oxytetracycline in milk samples by polymer inclusion membrane separation coupled to high performance liquid chromatography

The determination of oxytetracycline in milk samples using a polymer inclusion membrane concept with high performance liquid chromatography (HPLC) was studied. The membranes developed are composed by cellulose acetate as polymer base, Cyanex 923 as carrier and o-nitrophenyl octyl ether as plasticizer. In the optimal conditions, the method exhibits good linearity in the range 0.03–0.20 mg L⁻¹ with a limit of detection and quantification of 8.2 and 27.3 μg L⁻¹ respectively. The method was successfully applied to the analysis of milk samples with high selectivity.     

Improvement of the analysis of the biochemical oxygen demand (BOD) of Mediterranean seawater by seeding control

Biochemical oxygen demand (BOD) is a useful parameter for assessing the biodegradability of dissolved organic matter in water. At the same time, this parameter is used to evaluate the efficiency with which certain processes remove biodegradable natural organic matter (NOM). However, the values of BOD in seawater are very low (around 2 mg O₂ L⁻¹) and the methods used for its analysis are poorly developed. The increasing attention given to seawater desalination in the Mediterranean environment, and related phenomena such as reverse osmosis membrane biofouling, have stimulated interest in seawater BOD close to the Spanish coast. In this study the BOD analysis protocol was refined by introduction of a new step in which a critical quantity of autochthonous microorganisms, measured as adenosine triphosphate, is added. For the samples analyzed, this improvement allowed us to obtain reliable and replicable BOD measurements, standardized with solutions of glucose-glutamic acid and acetate. After 7 days of analysis duration, more than 80% of ultimate BOD is achieved, which in the case of easily biodegradable compounds represents nearly a 60% of the theoretical oxygen demand. BOD₇ obtained from the Mediterranean Sea found to be 2.0 ± 0.3 mg O₂ L⁻¹ but this value decreased with seawater storage time due to the rapid consumption of labile compounds. No significant differences were found between two samples points located on the Spanish coast, since their organic matter content was similar. Finally, the determination of seawater BOD without the use of inoculum may lead to an underestimation of BOD.     

Dissolved oxygen amperometric sensor based on layer-by-layer assembly using host-guest supramolecular interactions

The development of a simple, efficient and sensitive sensor for dissolved oxygen is proposed using the host-guest binding of a supramolecular complex at a host surface by combining a self-assembled monolayer (SAM) of mono-(6-deoxy-6-mercapto)-β-cyclodextrin (βCDSH), iron (III) tetra-(N-methyl-4-pyridyl)-porphyrin (FeTMPyP) and cyclodextrin-functionalized gold nanoparticles (CDAuNP). The supramolecular modified electrode showed excellent catalytic activity for oxygen reduction. The reduction potential of oxygen was shifted about 200 mV toward less negative values with this modified electrode, presenting a peak current much higher than those observed on a bare gold electrode. Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the oxygen reduction reaction involves probably 4-electrons with a rate constant (k_obs) of 7 × 10⁴ mol⁻¹ L s⁻¹. A linear response range from 0.2 up to 6.5 mg L⁻¹, with a sensitivity of 5.5 μA L mg⁻¹ (or 77.5 μA cm⁻² L mg⁻¹) and a detection limit of 0.02 mg L⁻¹ was obtained with this sensor. The repeatability of the proposed sensor, evaluated in terms of relative standard deviation was 3.0% for 10 measurements of a solution of 6.5 mg L⁻¹ oxygen.     

Evaluation of steviol and its glycosides in Stevia rebaudiana leaves and commercial sweetener by ultra-high-performance liquid chromatography-mass spectrometry

Stevia rebaudiana leaves contain non-cariogenic and non-caloric sweeteners (steviol-glycosides) whose consumption could exert beneficial effects on human health. Steviol-glycosides are considered safe; nonetheless, studies on animals highlighted adverse effects attributed to the aglycone steviol. The aim of the present study was to develop and validate two different ultra-high-performance liquid chromatography methods with electrospray ionization mass spectrometry (UHPLC-MS) to evaluate steviol-glycosides or steviol in Stevia leaves and commercial sweetener (Truvia^®). Steviol-glycosides identity was preliminarily established by UV spectra comparison, molecular ion and product ions evaluation, while routine analyses were carried out in single ion reaction (SIR) monitoring their negative chloride adducts. Samples were sequentially extracted by methanol, cleaned-up by SPE cartridge and the analytes separated by UHPLC HSS C₁₈ column (150 mm × 2.1 mm I.D., 1.8 μm). The use of CH₂Cl₂ added to the mobile phase as source of Cl⁻ enhance sensitivity. The LLOD for stevioside, rebaudioside A, steviolbioside and steviol was 15, 50, 10 and 1 ng ml⁻¹, respectively. Assay validation demonstrated good performances in terms of accuracy (89–103%), precision (<4.3%), repeatability (<5.7%) and linearity (40–180 mg/g). Stevioside (5.8 ± 1.3%), rebaudioside A (1.8 ± 1.2%) and rebaudioside C (1.3 ± 1.4%) were the most abundant steviol-glycosides found in samples of Stevia (n = 10) from southern Italy. Rebaudioside A was the main steviol-glycosides found in Truvia^® (0.84 ± 0.03%). The amounts of steviol-glycosides obtained by the UHPLC-MS method matched those given by the traditional LC-NH₂-UV method. Steviol was found in all the leaves extract (2.7–13.2 mg kg⁻¹) but was not detected in Truvia^® (<1 μg kg⁻¹). The proposed UHPLC-MS methods can be applied for the routine quality control of Stevia leaves and their commercial preparations.     

Enhanced response of microbial fuel cell using sulfonated poly ether ether ketone membrane as a biochemical oxygen demand sensor

The present study is focused on the development of single chamber microbial fuel cell (SCMFC) using sulfonated poly ether ether ketone (SPEEK) membrane to determine the biochemical oxygen demand (BOD) matter present in artificial wastewater (AW). The biosensor produces a good linear relationship with the BOD concentration up to 650 ppm when using artificial wastewater. This sensing range was 62.5% higher than that of Nafion^®. The most serious problem in using MFC as a BOD sensor is the oxygen diffusion into the anode compartment, which consumes electrons in the anode compartment, thereby reducing the coulomb yield and reducing the electrical signal from the MFC. SPEEK exhibited one order lesser oxygen permeability than Nafion^®, resulting in low internal resistance and substrate loss, thus improving the sensing range of BOD. The system was further improved by making a double membrane electrode assembly (MEA) with an increased electrode surface area which provide high surface area for electrically active bacteria.     

A new BOD estimation method employing a double-mediator system by ferricyanide and menadione using the eukaryote Saccharomyces cerevisiae

A new biochemical oxygen demand (BOD) sensing method employing a double-mediator (DM) system coupled with ferricyanide and a lipophilic mediator, menadione and the eukaryote Saccharomyces cerevisiae has been developed. In this study, a stirred micro-batch-type microbial sensor with a 560 μL volume and a two-electrode system was used. The chronamperometric response of this sensor had a linear response between 1 μM and 10 mM hexacyanoferrate(II) (r² = 0.9995, 14 points, n = 3, average of relative standard deviation and R.S.D._av = 1.3%). Next, the optimum conditions for BOD estimation by the DM system (BOD_DM) were investigated and the findings revealed that the concentration of ethanol, used to dissolve menadione, influenced the sensor response and a relationship between the sensor output and glucose glutamic acid concentration was obtained over a range of 6.6-220 mg O₂ L⁻¹ (five points, n = 3, R.S.D._av 6.6%) when using a reaction mixture incubated for 15 min. Subsequently, the characterization of this sensor was studied. The sensor responses to 14 pure organic substances were compared with the conventional BOD₅ method and other biosensor methods. Similar results with the BOD biosensor system using Trichosporon cutaneum were obtained. In addition, the influence of chloride ion, artificial seawater and heavy metal ions on the sensor response was investigated. A slight influence of 20.0 g L⁻¹ chloride ion and artificial seawater (18.4 g L⁻¹ Cl⁻) was observed. Thus, the possibility of BOD determination for seawater was suggested in this study. In addition, no influence of the heavy metal ions (1.0 mg L⁻¹ Fe³⁺, Cu²⁺, Mn²⁺, Cr³⁺ and Zn²⁺) was observed. Real sample measurements using both river water and seawater were performed and compared with those obtained from the BOD₅ method. Finally, stable responses were obtained for 14 days when the yeast suspension was stored at 4 °C (response reduction, 93%; R.S.D. for 6 testing days, 9.1%).     

A highly selective molecularly imprinted electrochemiluminescence sensor for ultra-trace beryllium detection

A new molecularly imprinted electrochemiluminescence (ECL) sensor was proposed for highly sensitive and selective determination of ultratrace Be²⁺ determination. The complex of Be²⁺ with 4-(2-pyridylazo)-resorcinol (PAR) was chosen as the template molecule for the molecularly imprinted polymer (MIP). In this assay, the complex molecule could be eluted from the MIP, and the cavities formed could then selectively recognize the complex molecules. The cavities formed could also work as the tunnel for the transfer of probe molecules to produce sound responsive signal. The determination was based on the intensity of the signal, which was proportional to the concentrations of the complex molecule in the sample solution, and the Be²⁺ concentration could then be determined indirectly. The results showed that in the range of 7 × 10⁻¹¹ mol L⁻¹ to 8.0 × 10⁻⁹ mol L⁻¹, the ECL intensity had a linear relationship with the Be²⁺ concentrations, with the limit of detection of 2.35 × 10⁻¹¹ mol L⁻¹. This method was successfully used to detect Be²⁺ in real water samples.     

Effluent treatment using electrochemically bleached seawater-oxidative degradation of pollutants

Use of seawater electrolytically enriched with hypochlorite and the in situ generation of hypochlorite on the high seas, stand a good chance for disinfection and decrease of bio and non-biodegradable organics in effluent before discharged into estuaries and deep oceans. Enriched seawater effectively decreased the biological oxygen demand measured over 5 days (BOD) and chemical oxygen demand (COD) levels of semi-treated wastewater. The oxidative degradation of Brilliant Blue, a triaryl industrial dye by hypochlorite and electrolytically enriched seawater are compared at pH 6.5. Both had similar magnitude second-order rate constants (21±1 M⁻¹ s⁻¹) and procedure is feasible. Increase in acid concentration enhanced the reaction rate. With 1:1 and 1:100 molar ratios of dye to hypochlorite, the COD=140 mg L⁻¹ of 1.0×10⁻³ M dye reduced to 100 and 30 mg L⁻¹ respectively.     

Catalytic activity of iron hexacyanoosmate(II) towards hydrogen peroxide and nicotinamide adenine dinucleotide and its use in amperometric biosensors

Hydrogen peroxide and nicotinamide adenine dinucleotide (NADH) may be determined amperometrically using screen-printed electrodes chemically modified with iron(III) hexacyanoosmate(II) (Osmium purple) in flow injection analysis (FIA). The determination is based on the exploitation of catalytic currents resulting from the oxidation/reduction of the modifier. The performance of the sensor was characterized and optimized by controlling several operational parameters (applied potential, pH and flow rate of the phosphate buffer). Comparison has been made with analogous complexes of ruthenium (Ruthenium purple) and iron (Prussian blue). Taking into account the sensitivity and stability of corresponding sensors, the best results were obtained with the use of Osmium purple. The sensor exhibited a linear increase of the amperometric signal with the concentration of hydrogen peroxide in the range of 0.1-100 mg L⁻¹ with a detection limit (evaluated as 3σ) of 0.024 mg L⁻¹ with a R.S.D. 1.5% for 10 mg L⁻¹ H₂O₂ under optimized flow rate of 0.4 mL min⁻¹ in 0.1 M phosphate buffer carrier (pH 6) and a working potential of +0.15 V versus Ag/AgCl. Afterwards, a biological recognition element - either glucose oxidase or ethanol dehydrogenase - was incorporated to achieve a sensor facilitating the determination of glucose or ethanol, respectively. The glucose sensor gave linearity between current and concentration in the range from 1 to 250 mg L⁻¹ with a R.S.D. 2.4% for 100 mg L⁻¹ glucose, detection limit 0.02 mg L⁻¹ (3σ) and retained its original activity after 3 weeks when stored at 6 °C. Optimal parameters in the determination of ethanol were selected as: applied potential +0.45 V versus Ag/AgCl, flow rate 0.2 mL min⁻¹ in 0.1 M phosphate buffer carrier (pH 7). Different structural designs of the ethanol sensor were tested and linearity obtained was up to 1000 mg L⁻¹ with a maximum R.S.D. of 5.1%. Applications in food analysis were also examined.     

Biomimetic sensor based on MnMn complex as manganese peroxidase mimetic for determination of rutin

A novel biomimetic sensor for rutin determination based on a dinuclear complex [Mn^IIIMn^II(Ldtb)(μ-OAc)₂]BPh₄ containing an unsymmetrical dinucleating ligand, 2-[N,N-bis(2-pyridylmethyl)-aminomethyl]-6-[N-(3,5-di-tert-butyl-2-oxidoben-zyl)-N-(2-pyridylamino)aminomethyl]-4-methylphenol (H₂Ldtb), as a manganese peroxidase mimetic was developed. Several parameters were investigated to evaluate the performance of the biomimetic sensor obtained after the incorporation of the dinuclear complex in a carbon paste. The best performance was obtained in 75:15:10% (w/w/w) of the graphite powder:Nujol:Mn^IIIMn^II complex, 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0) and 4.0 × 10⁻⁵ mol L⁻¹ hydrogen peroxide. The response of the sensor towards rutin concentration was linear using square wave voltammetry in the range of 9.99 × 10⁻⁷ to 6.54 × 10⁻⁵ mol L⁻¹ (r = 0.9998) with a detection limit of 1.75 × 10⁻⁷ mol L⁻¹. The recovery study performed with pharmaceuticals ranged from 96.6% to 103.2% and the relative standard deviation was 1.85% for a solution containing 1.0 × 10⁻³ mol L⁻¹ rutin (n = 6). The lifetime of this biomimetic sensor was 200 days (at least 750 determinations). The results obtained for rutin in pharmaceuticals using the biomimetic sensor and those obtained with the official method are in agreement at the 95% confidence level.     

Sequential injection methodology for carbon speciation in bathing waters

A sequential injection method (SIA) for carbon speciation in inland bathing waters was developed comprising, in a single manifold, the determination of dissolved inorganic carbon (DIC), free dissolved carbon dioxide (CO₂), total carbon (TC), dissolved organic carbon and alkalinity. The determination of DIC, CO₂ and TC was based on colour change of bromothymol blue (660 nm) after CO₂ diffusion through a hydrophobic membrane placed in a gas diffusion unit (GDU). For the DIC determination, an in-line acidification prior to the GDU was performed and, for the TC determination, an in-line UV photo-oxidation of the sample prior to GDU ensured the conversion of all carbon forms into CO₂. Dissolved organic carbon (DOC) was determined by subtracting the obtained DIC value from the TC obtained value. The determination of alkalinity was based on the spectrophotometric measurement of bromocresol green colour change (611 nm) after reaction with acetic acid. The developed SIA method enabled the determination of DIC (0.24–3.5 mg C L⁻¹), CO₂ (1.0–10 mg C L⁻¹), TC (0.50–4.0 mg C L⁻¹) and alkalinity (1.2–4.7 mg C L⁻¹ and 4.7–19 mg C L⁻¹) with limits of detection of: 9.5 μg C L⁻¹, 20 μg C L⁻¹, 0.21 mg C L⁻¹, 0.32 mg C L⁻¹, respectively. The SIA system was effectively applied to inland bathing waters and the results showed good agreement with reference procedures.     

A novel high selective and sensitive metronidazole voltammetric sensor based on a molecularly imprinted polymer-carbon paste electrode

The design and construction of a highly selective voltammetric sensor for metronidazole by using a molecularly imprinted polymer (MIP) as recognition element were introduced. A metronidazole selective MIP and a nonimprinted polymer (NIP) were synthesized and then incorporated in the carbon paste electrodes (CPEs). The sensor was applied for metronidazole determination using cathodic stripping voltammetric method. The MIP-CP electrode showed very high recognition ability in comparison to NIP-CPE. Some parameters affecting the sensor response were optimized and then the calibration curve was plotted. Two dynamic linear ranges of 5.64 × 10⁻⁵ to 2.63 × 10⁻³ mg L⁻¹ and 2.63 × 10⁻³ to 7.69 × 10⁻² mg L⁻¹ were obtained. The detection limit of the sensor was calculated as 3.59 × 10⁻⁵ mg L⁻¹. This sensor was used successfully for metronidazole determination in biological fluids.