Preparation and properties of Nafion/hollow silica spheres composite membranes

In present work, hollow silica spheres (HSS)/Nafion^® composite membranes were prepared by solution casting. The thermal properties, water retention, swelling behavior and proton conductivity of the composite membranes were explored. It was found that HSS dispersed well at micrometer scale in the obtained composite membranes by SEM and TEM observation. Thermal properties of composite membranes were improved than that of recast Nafion^® membrane. Compared with the recast Nafion^® membrane, the composite membranes showed higher water uptake and lower swelling degree at the temperature range from 40 to 100 °C. At the same HSS loading, the smaller the diameter of HSS in composite membranes, the more the water uptake, however, the swelling degree of composite membranes was increased. The proton conductivity of the composite membrane with 3–5 wt.% HSS (120 and 250 nm) increased distinctively at above 60 °C, reached the optimal value at 100 °C, and decreased slowly when the temperature exceeded 100 °C.     

Synthesis of fluoro-containing sulfonated poly(phthalazinone ether ketone ketone)s and their properties as PEM in PEMFC and DMFC

A series of sulfonated poly(ether ketone ketone)s (SPPFEKKs) containing both of phthalazinone and hexafluoroisopropylidene moieties were synthesized by direct nucleophilic polycondensation reaction from 4-(4-hydroxyphenyl)-1(2H)-phthalazinone (DHPZ), 4,4-hexafluoroisopropylidene-diphenol (BPAF), 1,4-bi(4-fluorobenzoyl) benzene (DFKK) and 1,4-bi(3-sodium sulfonate-4-fluorobenzoyl) benzene (SDFKK). The obtained SPPFEKKs had high molecular weight with inherent viscosity ranged from 1.29 to 1.53 dL/g and their chemical structure was characterized by FT-IR and ¹H NMR. The ionic membranes of SPPFEKKs showed high proton conductivity, for instance, SPPFEKK-120 (DS = 1.20) demonstrated 1.0 × 10⁻¹ S/cm proton conductivity at 95 °C, which was very close to that of Nafion^®117. All the SPPFEKK membranes exhibited methanol permeability lower than 2.76 × 10⁻⁷ cm²/s, which was much lower than that of Nafion^®117 (2.38 × 10⁻⁶ cm²/s). These copolymers also showed excellent thermal stability and good solubility in aprotic polar organic solvents. The ionic membranes of SPPFEKK demonstrated tensile strength varied from 57 to 69 MPa depending on their DS.     

A composite thin film optical sensor for dissolved oxygen in contaminated aqueous environments

A robust optical composite thin film dissolved oxygen sensor was fabricated by ionically trapping the dye ruthenium(II) tris(4,7-diphenyl-1,10-phenanthroline) dichloride in a blended fluoropolymer matrix consisting of Nafion^® and Aflas^®. Strong phosphorescence, which was strongly quenched by dissolved oxygen (DO), was observed when the sensor was immersed in water. The sensor was robust, optically transparent, with good mechanical properties. Fast response, of a few seconds, coupled with sensitivity of about 0.1 mg L⁻¹ (DO) over the range 0-30 mg L⁻¹ and resistance to leaching, were also exhibited by this system. The Stern-Volmer (SV) plot exhibited slight downward turning at all oxygen concentrations. A linear plot was obtained when the SV equation was modified to account for the varying sensitivity of dye molecules in the matrix to the quencher. Good long term stability was observed.     

Zirconium meta-sulfonphenyl phosphonic acid-incorporated Nafion membranes for reduction of methanol permeability

Zirconium meta-sulfonphenyl phosphonic acid (Zr-msPPA)/Nafion^® composite membranes were prepared to reduce methanol permeability of the Nafion^® 117 membrane in direct methanol fuel cell (DMFC) applications. Zr-msPPA crystalline nano proton conductors were synthesized inside the membranes via the reaction of zirconium chloride octahydrate and meta-sulfonphenyl phosphonic acid that had been soaked prior. Synthesis of the Zr-msPPA in the membranes was identified from a series of chemical and physical structure characterizations using FTIR, NMR, EDS, and XRD spectroscopy. The thermal stability of the composite membranes was enhanced by addition of the Zr-msPPA, with considerable reduction in methanol permeability with increasing Zr-msPPA content, as the Zr-msPPA nano conductors acted as crystalline barriers to methanol permeation. The ion conductivity also decreased with increasing Zr-msPPA content, but its effect was not as strong as with methanol permeation given the innate, high conductivity of Zr-msPPA.     

A study of linear versus angled rigid rod polymers for proton conducting membranes using sulfonated polyimides

Linear and angled monomers were incorporated into the main chain of a polyimide in order to investigate the effect of kinked versus linear polymers on membrane properties such as water uptake and proton conductivity. Polymers prepared using linear 4,4′-sulfonyldianiline, SPI1, and using angled 3,4′-sulfonyldianiline, SPI2, were cast into membranes possessing ion exchange capacities that varied from 0.79 to 2.75 meq g⁻¹. Membranes are thermally stable up to 300 °C under air. Proton conductivity of both membranes increases with temperature to values of 0.1-0.2 S cm⁻¹. The conductivity of angled, SPI2 membranes is greater than those prepared from SPI1 for a given IEC but water uptakes are lower. These differences are attributed to increased entanglements of the angled polymers, which limits the degree of swelling and increases the proton concentration. These results may be important in the design of proton conducting membranes from other rigid polyarylenes.     

Composite Nafion membrane embedded with hybrid nanofillers for promoting direct methanol fuel cell performance

A special type of hybrid nano-particles was incorporated into the Nafion^® matrix to form a composite membrane. These nano-particles possessed a core–shell structure consisting of silica core (<10 nm) and a densely grafted oligomeric ionmer layer, which was synthesized via atom transfer radical polymerization (ATRP) on the particles’ surface. Besides considerable improvement in the proton conductivity of the membrane, the presence of these hybrid nano-particles in the Nafion^® matrix also repressed its methanol permeability by almost four times. The composite membrane also demonstrated superior performance when tested in a single cell membrane-electrolyte assembly (MEA) under direct methanol fuel cell (DMFC) operating condition. It was found that the composite membrane enabled a power density output that was 1.5 times greater than that of pristine Nafion^®.     

Validation of a direct non-destructive quantitative analysis of amiodarone hydrochloride in Angoron formulations using FT-Raman spectroscopy

Raman spectroscopy was applied for the direct non-destructive analysis of amiodarone hydrochloride (ADH), the active ingredient of the liquid formulation Angoron^®. The FT-Raman spectra were obtained through the un-broken as-received ampoules of Angoron^®. Using the most intense vibration of the active pharmaceutical ingredient (API) at 1568 cm⁻¹, a calibration model, based on solutions with known concentrations, was developed. The model was applied to the Raman spectra recorded from three as-purchased commercial formulations of Angoron^® having nominal strength of 50 mg ml⁻¹ ADH. The average value of the API in these samples was found to be 48.56 ± 0.64 mg ml⁻¹ while the detection limit of the proposed technique was found to be 2.11 mg ml⁻¹. The results were compared to those obtained from the application of HPLC using the methodology described in the European Pharmacopoeia and found to be in excellent agreement. The proposed analytical methodology was also validated by evaluating the linearity of the calibration line as well as its accuracy and precision. The main advantage of Raman spectroscopy over HPLC method during routine analysis is that it is considerably faster and no solvent consuming. Furthermore, Raman spectroscopy is non-destructive for the sample. However, the detection limit for Raman spectroscopy is much higher than the corresponding for the HPLC methodology.     

Fluorinated polyoxadiazole for high-temperature polymer electrolyte membrane fuel cells

For the first time a fluorinated polyoxadiazole doped with phosphoric acid as a proton-conducting membrane for operation at temperatures above 100 °C and low humidities for fuel cells has been reported. Fluorinated polyoxadiazole with remarkable chemical stability was synthesized. No changes in the molecular weight (about 200,000 g mol⁻¹) can be observed when the polymer is exposed for 19 days to mixtures of sulfuric acid and oleum. Protonated membranes with low doping level (0.34 mol of phosphoric acid per polyoxadiazole unit, 11.6 wt.% H₃PO₄) had proton conductivity at 120 °C and RH = 100% in the order of magnitude of 10⁻² S cm⁻¹. When experiments are conducted at lower external humidity, proton conductivity values drop an order of magnitude. However still a high value of proton conductivity (6 × 10⁻³ S cm⁻¹) was obtained at 150 °C and with relative humidity of 1%. In an effort to increase polymer doping, nanocomposite with sulfonated silica containing oligomeric fluorinated-based oxadiazole segments has also been prepared. With the addition of functionalized silica not only doping level but also water uptake increased. For the nanocomposite membranes prepared with the functionalized silica higher proton conductivity in all range of temperature up to 120 °C and RH = 100% (in the order of magnitude of 10⁻³ S cm⁻¹) was observed when compared to the plain membrane (in the order of magnitude of 10⁻⁵ S cm⁻¹).     

Synthesis of novel crosslinked sulfonated poly(ether sulfone)s using bisazide and their properties for fuel cell application

Novel crosslinked sulfonated poly(ether sulfone)s (PESs) were prepared by thermal irradiation of the allyl-terminated telechelic sulfone polymers using a bisazide. The sulfonated polymers in different comonomer compositions were fully characterized by ¹H NMR, and the crosslinked structure was also verified by FT-IR spectroscopic analyses. Having both the uniform distribution of the hydrophilic conductive sites and controlled hydrophobic nature by minimized crosslinking over the rigid rod poly(ether sulfone) backbone, the crosslinked polymer membrane (PES-60) offered excellent proton conductivity of 0.79 S cm⁻¹ at 100 °C together with hydrolytic and oxidative stability. In addition, only 17% of methanol permeability of the Nafion^® was observed for the crosslinked PES-60.     

Calibration and use of the Chemcatcher passive sampler for monitoring organotin compounds in water

An integrative passive sampler (Chemcatcher^®) consisting of a 47 mm C₁₈ Empore™ disk as the receiving phase overlaid with a thin cellulose acetate diffusion membrane was developed and calibrated for the measurement of time-weighted average water concentrations of organotin compounds [monobutyltin (MBT), dibutyltin (DBT), tributlytin (TBT) and triphenyltin (TPhT)] in water. The effect of water temperature and turbulence on the uptake rate of these analytes was evaluated in the laboratory using a flow-through tank. Uptake was linear over a 14-day period being in the range: MBT (3-23 mL day⁻¹), DBT (40-200 mL day⁻¹), TBT (30-200 mL day⁻¹) and TPhT (30-190 mL day⁻¹) for all the different conditions tested. These sampling rates were high enough to permit the use of the Chemcatcher^® to monitor levels of organotin compounds typically found in polluted aquatic environments. Using gas chromatography (GC) with either ICP-MS or flame photometric detection, limits of detection for the device (14-day deployment) for the different organotin compounds in water were in the range of 0.2-7.5 ng L⁻¹, and once accumulated in the receiving phase the compounds were stable over prolonged periods. Due to anisotropic exchange kinetics, performance reference compounds could not be used with this passive sampling system to compensate for changes in sampling rate due to variations in water temperature, turbulence and biofouling of the surface of the diffusion membrane during field deployments. The performance of the Chemcatcher^® was evaluated alongside spot water sampling in Alicante Habour, Spain which is known to contain elevated levels of organotin compounds. The samplers provided time-weighted average concentrations of the bioavailable fractions of the tin compounds where environmental concentrations fluctuated markedly in time.     

High efficiency direct methanol fuel cell based on poly(styrenesulfonic) acid (PSSA)-poly(vinylidene fluoride) (PVDF) composite membranes

semi-Interpenetrating polymer network (sIPN) composite membranes consisting of poly(styrenesuflonic) acid (PSSA) and poly(vinylidene fluoride) (PVDF) have been prepared and evaluated as proton exchange membrane electrolytes in direct methanol fuel cells (DMFCs). The membranes fabricated were evaluated in terms of their proton conductivity, methanol permeability, and their performance characteristics in direct methanol fuel cells (DMFCs). PSSA-PVDF membranes demonstrated decreased methanol crossover during operation of direct methanol fuel cells compared to state-of-art Nafion^®-H membranes, yielding improved efficiency. PSSA-PVDF membranes have been demonstrated to operate efficiently in 1 in. × 1 in. and 2 in. × 2 in. direct methanol fuel cells. Fuel cells operating with PSSA-PVDF membranes were observed to have dramatically lower crossover rates compared to Nafion^® 117 systems. Greater than 95% reduction in crossover was observed in some cases. These properties of PSSA-PVDF membranes resulted in improved fuel performance and fuel cell efficiencies for direct methanol fuel cells. It was also observed that the PSSA-PVDF membranes behave quite differently compared with Nafion^®-based systems in terms water management characteristics at the cathode. The best performance with the new membranes was observed with very low oxygen or air flow rates at the cathode which is in contrast to Nafion^®-based systems, which generally require higher flow rates due to excessive water accumulation at the cathode, resulting in flooding.     

Vibrational and thermal characterization of Nafion membranes substituted by alkaline earth cations

The vibrational spectra of Nafion^® membranes with alkaline earth cations as counterions have been obtained by photoacoustic infrared spectroscopy (PAS-IR) and Fourier transform Raman spectroscopy (FT-Raman). The symmetrical stretching band of the sulfonate group (∼1060 cm⁻¹) decreases with increasing atomic mass of the countercation, excepting for Mg²⁺, in both techniques. The thermal behavior of Nafion membranes by means of differential scanning calorimetry (DSC) curves showed a dependence on the water content and a similar profile between Nafion-Mg²⁺ and -Ca²⁺, and between Nafion-Sr²⁺ and -Ba²⁺, for the first scanning curve. An ageing effect was also observed on Nafion by DSC curves. High-resolution thermogravimetry (TG) curves under nitrogen atmosphere showed similar decomposition profiles. It was determined from TG curves that there is a decreasing water content with increasing ionic radius of cation, and the thermal stability increasing from Nafion-Mg²⁺ to -Ba²⁺.     

Enhanced response of microbial fuel cell using sulfonated poly ether ether ketone membrane as a biochemical oxygen demand sensor

The present study is focused on the development of single chamber microbial fuel cell (SCMFC) using sulfonated poly ether ether ketone (SPEEK) membrane to determine the biochemical oxygen demand (BOD) matter present in artificial wastewater (AW). The biosensor produces a good linear relationship with the BOD concentration up to 650 ppm when using artificial wastewater. This sensing range was 62.5% higher than that of Nafion^®. The most serious problem in using MFC as a BOD sensor is the oxygen diffusion into the anode compartment, which consumes electrons in the anode compartment, thereby reducing the coulomb yield and reducing the electrical signal from the MFC. SPEEK exhibited one order lesser oxygen permeability than Nafion^®, resulting in low internal resistance and substrate loss, thus improving the sensing range of BOD. The system was further improved by making a double membrane electrode assembly (MEA) with an increased electrode surface area which provide high surface area for electrically active bacteria.     

Synthesis and characterization of fluorinated ionomer p-perfluoro-[1-(2-sulfonic)ethoxy]ethylated polyacrylonitrile-styrene

Fluorinated ionomer p-perfluoro[1-(2-sulfonic)ethoxy]ethylated polyacrylonitrile-styrene (SFAS) (5) was synthesized via electron transfer reaction between polyacrylonitrile-styrene (AS) (1) and perfluoro-di[2-(2-fluorosulfonyl)ethoxy]propionyl peroxide (FAP) (2) and followed by alkali hydrolysis and acidification of p-perfluoro[1-(2-fluorosulfonyl)ethoxy]ethylated polyacrylonitrile-styrene (3). The microstructure of ionomer 5 was well characterized by FTIR and ¹⁹F NMR. Its desulfonation occurred above 197 °C was found by TGA, the degree of substitution (DS) and ion exchange capacity (IEC) determined by titration were well controlled through changing the molar ratio of 2:1. The proton exchange membranes made of ionomer 5 have water uptake from 13.4 to 135.3% and conductivity up to 10⁻² S cm⁻¹ at 25 °C.     

Evaluation of steviol and its glycosides in Stevia rebaudiana leaves and commercial sweetener by ultra-high-performance liquid chromatography-mass spectrometry

Stevia rebaudiana leaves contain non-cariogenic and non-caloric sweeteners (steviol-glycosides) whose consumption could exert beneficial effects on human health. Steviol-glycosides are considered safe; nonetheless, studies on animals highlighted adverse effects attributed to the aglycone steviol. The aim of the present study was to develop and validate two different ultra-high-performance liquid chromatography methods with electrospray ionization mass spectrometry (UHPLC-MS) to evaluate steviol-glycosides or steviol in Stevia leaves and commercial sweetener (Truvia^®). Steviol-glycosides identity was preliminarily established by UV spectra comparison, molecular ion and product ions evaluation, while routine analyses were carried out in single ion reaction (SIR) monitoring their negative chloride adducts. Samples were sequentially extracted by methanol, cleaned-up by SPE cartridge and the analytes separated by UHPLC HSS C₁₈ column (150 mm × 2.1 mm I.D., 1.8 μm). The use of CH₂Cl₂ added to the mobile phase as source of Cl⁻ enhance sensitivity. The LLOD for stevioside, rebaudioside A, steviolbioside and steviol was 15, 50, 10 and 1 ng ml⁻¹, respectively. Assay validation demonstrated good performances in terms of accuracy (89–103%), precision (<4.3%), repeatability (<5.7%) and linearity (40–180 mg/g). Stevioside (5.8 ± 1.3%), rebaudioside A (1.8 ± 1.2%) and rebaudioside C (1.3 ± 1.4%) were the most abundant steviol-glycosides found in samples of Stevia (n = 10) from southern Italy. Rebaudioside A was the main steviol-glycosides found in Truvia^® (0.84 ± 0.03%). The amounts of steviol-glycosides obtained by the UHPLC-MS method matched those given by the traditional LC-NH₂-UV method. Steviol was found in all the leaves extract (2.7–13.2 mg kg⁻¹) but was not detected in Truvia^® (<1 μg kg⁻¹). The proposed UHPLC-MS methods can be applied for the routine quality control of Stevia leaves and their commercial preparations.     

Synthesis and properties of novel sulfonated polyimides containing phthalazinone moieties for PEMFC

A novel sulfonated diamine, 1,2-dihydro-2-(3-sulfonic-4-aminophenyl)-4-[4-(3-sulfonic-4-aminophenoxy)-phenyl]-phthalazin-1-one(S-DHPZDA), was successfully synthesized and two series of six-membered sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), S-DHPZDA, and nonsulfonated diamines DHPZDA or 4,4′-diaminodiphenyl ether (ODA). The chemical structure of the S-DHPZDA and the SPIs were characterized by ¹H NMR and FT-IR. Tough, brownish and transparent membranes were cast from SPIs’ solution in NMP. The water uptake, swelling ratio, chemical and thermal stability, hydrolytic and oxidative stability as well as proton conductivity of these new polymers were investigated systematically. Compared with Nafions, the obtained SPI membranes have onset decomposed temperatures of these two series SPIs were above 318 °C and decomposed temperature of main chain were 565 °C and excellent dimension stabilities on similar IECs. Introduction of phthalazinone moieties had improved the copolyimides’ solubility in polar aprotic organic solvents like m-cresol, NMP, DMSO, DMF etc. The SPIs had high proton conductivity (σ) in the order of magnitude of 10⁻³ to 10⁻² S cm⁻¹ depending on the degree of sulfonation (DS) of the polymers.     

Synthesis and characterization of novel sulfonated naphthalenic polyimides as proton conductive membrane for DMFC applications

To prepare proton conductive membrane for direct methanol fuel cells (DMFC), a novel sulfonated aromatic diamine monomer, 1,4-bis(4-amino-2-sulfonic acid-phenoxy)-benzene (DSBAPB) was synthesized and characterized by ¹H NMR and FT-IR. Then a series of sulfonated polyimides (SPIs) were prepared from DSBAPB with 1,4,5,8-naphthalene tetracarboxylic dianhydride (NTDA) and a non-sulfonated diamine, 4,4′-oxydianiline (ODA) via one-step high-temperature polymerization method. The sulfonation degree of the SPIs can be controlled by changing the mole ratio of sulfonated monomer to non-sulfonated monomer. The obtained SPI membranes exhibit desirable proton conductivity ranged from 7.9 × 10⁻³ to 7.2 × 10⁻² S cm⁻¹ and low methanol permeability of less than 2.85 × 10⁻⁷ cm² s⁻¹. Furthermore, the hydrolysis stability of the obtained SPIs is better than the BDSA based SPIs caused by the flexible structure.     

Electrochemical behavior of hexafluoroniobate, heptafluorotungstate, and oxotetrafluorovanadate anions in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide room temperature ionic liquid

Electrochemical behavior of hexafluoroniobate (Nb(V)F₆⁻), heptafluorotungstate (W(VI)F₇⁻), and oxotetrafluorovanadate (V(V)OF₄⁻) anions has been investigated in N-butyl-N-methylpyrrolidinium bis(trifluoromethylsulfonyl)amide (BMPyrTFSA) ionic liquid at 298 K by means of cyclic voltammetry and chronoamperometry. Cyclic voltammograms at a Pt electrode showed that Nb(V)F₆⁻ anion is reduced to Nb(IV)F₆²⁻ by a one-electron reversible reaction. Electrochemical reductions of W(VI)F₇⁻ and V(V)OF₄⁻ anions at a Pt electrode are quasi-reversible and irreversible reactions, respectively, according to cyclic voltammetry. The diffusion coefficients of Nb(V)F₆⁻, W(VI)F₇⁻ and V(V)OF₄⁻ determined by chronoamperometry are 1.34 × 10⁻⁷, 7.45 × 10⁻⁸ and 2.49 × 10⁻⁷ cm² s⁻¹, respectively. The Stokes radii of Nb(V)F₆⁻, W(VI)F₇⁻, and V(V)OF₄⁻ in BMPyrTFSA have been calculated to be 0.23, 0.38, and 0.12 nm, from the diffusion coefficients and viscosities obtained.     

Synthesis of proton conductive inorganic–organic hybrid membranes from organoalkoxysilane and hydroxyalkylphosphonic acid

Proton conductive inorganic–organic hybrid membranes were synthesized from 3-glycidyloxypropyltrimethoxysiane (GPTMS), phenyltriethoxysilane (PhTES) and hydroxyalkylphosphonic acid. Two kinds of hydroxyalkylphosphonic acids, 1-hydroxyethane-1,1-diphosphonic acid (HEDPA) and hydroxyethanephosphonic acid (HEPA), were incorporated into the membranes as functional molecules for proton conduction. FT-IR and Raman studies revealed the presence of phosphonic acid groups in the hybrid membranes. ¹³C and ²⁹Si NMR confirmed that a three-dimensional siloxane network was formed in the prepared hybrid membrane by hydrolysis and condensation reactions. DTA-TG analysis showed that these membranes were thermally stable up to 200 °C. The HEDPA-based system was found to have higher proton conductivities than the HEPA-based one. The proton conductivities of the hybrid membranes increased with the phosphonic acid content and temperature up to 130 °C. The conductivities of the HEDPA/GPTMS/PhTES membranes = 1/1.6/0.4 were 1.0 × 10⁻¹ and 4.5 × 10⁻⁴ S cm⁻¹ at 100% relative humidity and non-humidified conditions, respectively, at 130 °C.     

An amperometric method for the detection of amitrole, glyphosate and its aminomethyl-phosphonic acid metabolite in environmental waters using passive samplers

The herbicides amitrole and glyphosate, and its metabolite aminomethyl-phosphonic acid (AMPA), in water samples have been directly analysed by high-performance liquid chromatography using an electrochemical (EC) detector. Limits of detection of 0.3 μg mL⁻¹ for glyphosate, 0.05 μg mL⁻¹ for AMPA and 0.03 μg mL⁻¹ for amitrole were comparable to those obtained by other authors using EC and also by liquid chromatography coupled to mass spectrometry, but the latter method requires derivatisation and pre-concentration of the sample whereas EC methods show similar sensitivity without the need of any derivatisation. The method was specifically designed to analyse extracts from passive samplers used for monitoring of polar herbicide residues in waters. To this purpose, three types of Empore^® disks were tested for their ability to adsorb and desorb these ionic, polar analytes. A procedure for their extraction from the membranes and reducing the interferences from other substances present in natural waters (i.e. humic acids) is described. The method is simple, does not require sophisticated equipment and is valid for the analysis and monitoring of herbicides residues using passive samplers.