An experimental investigation of the combined effects of surface curvature and streamwise pressure gradients both in laminar and turbulent flows

Flow and heat transfer characteristics over flat, concave and convex surfaces have been investigated in a low speed wind tunnel in the presence of adverse and favourable pressure gradients (k), for a range of –3.6 × 10^–6 ≤ k ≤ +3.6 × 10^–6. The laminar near zero pressure gradient flow, with an initial momentum thickness Reynolds number of 200, showed that concave wall boundary layer was thinner and heat transfer coefficients were almost 2 fold of flat plate values. Whereas for the same flow condition, thicker boundary layer and 35% less heat transfer coefficients of the convex wall were recorded with an earlier transition. Accelerating laminar flows caused also thinner boundary layers and an augmentation in heat transfer values by 28%, 35% and 16% for the flat, concave and convex walls at k = 3.6 × 10^–6. On the other hand decelerating laminar flows increased the boundary layer thickness and reduced Stanton numbers by 31%, 26% and 22% on the flat surface, concave and convex walls respectively. Turbulent flow measurements at k = 0, with an initial momentum thickness Reynolds number of 1100, resulted in 30% higher and 25% lower Stanton numbers on concave and convex walls, comparing to flat plate values. Moreover the accelerating turbulent flow of k = 0.6 × 10^–6 brought about 29%, 30% and 24% higher Stanton numbers for the flat, concave and convex walls and the decelerating turbulent flow of k = –0.6 × 10^–6 caused St to decrease up to 27%, 25% and 29% for the same surfaces respectively comparing to zero pressure gradient values. An empirical equation was also developed and successfully applied, for the estimation of Stanton number under the influence of pressure gradients, with an accuracy of better than 4%.     

Turbulent heat-transfer characteristics along the heated convex wall of a rectangular cross-sectional return bend

The turbulent heat-transfer characteristics along the heated convex wall of a return bend which has rectangular cross section with large ratio have been examined for various clearances of the duct in detail. The experiments are performed under condition that the convex wall is heated at uniform heat flux while the concave wall is insulated. Water as a working fluid is utilized. Using four kinds of clearances of 15, 40, 60 and 80 mm, the Reynolds number in the turbulent range is varied from 8×10³ to 8×10⁴ with Prandtl number ranging from 6.5 to 8.5. In consequence, it is found that both the local and the mean heat-transfer rates are always smaller than those for straight parallel plates or for the straight duct. It is also found that the local heat-transfer characteristics in the outlet region of the return bend are more sensitively influenced by the variation of duct clearance than those in the inlet region.     

Experimental investigation on turbulent flow in a square-sectioned 90-degree bend

The development of steady, turbulent flow in a 90° section of a curved square duct was studied at a Reynolds number of 4 × 10⁴ by hot-wire anemometer. The curved duct has a cross-section measuring 80 × 80 mm and a curvature radius ratio of 4 and is connected with a long, straight duct at its both ends. The longitudinal and lateral components of mean and fluctuating velocities, and the Reynolds stresses were measured by the method of rotating a probe with an inclined hot-wire. The velocity fields of the primary and secondary flows, and the Reynolds stress distributions in the cross-section were illustrated in the form of contour map. The development of the primary flow was found to be connected with a strong pressure gradient near the outer and inner wall and a secondary flow induced in the cross-section of the bend by a pressure difference between the outer and inner wall and a centrifugal force acting on the fluid; the fluid is accelerated near the inner wall and decelerated near the outer wall between the bend angle ϕ ≅ 0° and ϕ ≅ 30°, but an increase and decrease of the fluid velocity are reversed between ϕ ≅ 30° and ϕ ≅ 90°. The fluctuating velocity correlations, i.e. the Reynolds stresses follow a complicated progress according to the complex development of the primary flow. The results obtained can be available to verify various types of turbulence models and to develop new models. Received: 10 May 1999/Accepted: 15 March 2000     

Experimental investigation on turbulent flow in a circular-sectioned 90-degree bend

 The steady, turbulent flow in a circular-sectioned 90° bend with smooth walls has been investigated experimentally. The bend had a curvature radius ratio of 4.0 with long, straight upstream and downstream pipes. The longitudinal, circumferential and radial components of mean and fluctuating velocities, and the Reynolds stresses in the pipe cross section at several longitudinal stations were obtained with the technique of rotating a probe with an inclined hot wire at a Reynolds number of 6×10⁴. The velocity fields of the primary and secondary flows, and the Reynolds stress distributions in the cross section were illustrated. Moreover, other characteristics of the bend flow, such as deviation of the primary flow and intensity of the secondary flow, were presented. Simultaneously, discussions were given on the transition of phenomena in the longitudinal direction and the structures of turbulence in the 90° bend. Received: 21 April 1997/Accepted: 14 November 1997     

Heat transfer and flow around a circular cylinder with tripping-wires

An experimental study was conducted on the heat transfer under the condition of constant heat flux and the flow around a circular cylinder with tripping-wires, which were affixed at ± 65° from the forward stagnation point on the cylinder surface. The testing fluid was air and the Reynolds number Red, based on the cylinder diameter, ranged from 1.2 × 10⁴ to 5.2×10⁴. Especially investigated are the interactions between the heat transfer and the flow in the critical flow state, in relation to the static pressure distribution along the cylinder surface and the mean and turbulent fluctuating velocities in the wake. It is found that the heat transfer from the cylinder to the cross flow is in very close connection with the width of near wake.     

Experimental investigation on turbulent flow through a circular-sectioned 180° bend

The steady, developing turbulent flow in a circular-sectioned 180° bend has been investigated. The bend had a radius of 104 mm and a curvature radius ratio of 4.0 with long, straight upstream and downstream pipes. Measurements of the longitudinal, radial and circumferential components of mean velocity, and corresponding components of the Reynolds stress were obtained with a hot wire anemometer at a Reynolds number of 6×10⁴ and at various longitudinal stations. The velocity fields of the primary and secondary flows and the Reynolds stresses were illustrated in the form of contour map or vector diagram. Moreover, the mean quantities characterizing the bend flow, i.e., the deflection of the primary flow in the cross section, the intensity of the secondary flow and the turbulence energy, were shown in a graphic form against the longitudinal distances. In the section upstream from a bend angle of about 60°, both the flows through the 180° and the 90° bend are closely similar in their behavior. In the section from the bend angle of 90°, the high-velocity regions, however, occur near the upper and lower walls as a result of strong secondary flow and the turbulence with high level emerges in the central region of the bend. Just behind the bend exit, an additional pair of vortices appears in the outer part of the cross section owing to the transverse pressure difference. In the downstream tangent, the flow returns slowly to the proper flow in a straight pipe, but it needs a longer distance for recovery than in the 90° bend. Received: 23 April 1998/Accepted: 24 April 1999     

Heat transfer and flow temperature measurements in a rotating triangular channel with various rib arrangements

In the present study, the regionally-averaged heat transfer coefficients and flow temperature distributions were measured in an equilateral triangular channel with three different rib arrangements (α = 45, 90 and 135°). To measure regionally-averaged heat transfer coefficients in the channel, two rows of copper blocks and a single heater were installed on two ribbed walls. The fluid temperature distributions were obtained using a thermocouple-array. The rotation number ranged from 0.0 to 0.1 with a fixed Reynolds number of 10,000. For the 90° ribs, the heat transfer coefficients on the pressure side surface were increased significantly with rotation, while the suction side surface had lower heat transfer coefficients than the stationary channel. For the angled ribs, rib-induced secondary flow dominated the heat transfer characteristics and high heat transfer rates were observed on the regions near the inner wall for the 45° angled ribs and near the leading edge for the 135° angled ribs.     

Heat transfer performance comparison of steam and air in gas turbine cooling channels with different rib angles

Using steam as working fluid to replace compressed air is a promising cooling technology for internal cooling passages of blades and vanes. The local heat transfer characteristics and the thermal performance of steam flow in wide aspect ratio channels (W/H = 2) with different angled ribs on two opposite walls have been experimentally investigated in this paper. The averaged Nusselt number ratios and the friction factor ratios of steam and air in four ribbed channels were also measured under the same test conditions for comparison. The Reynolds number range is 6,000–70,000. The rib angles are 90°, 60°, 45°, and 30°, respectively. The rib height to hydraulic diameter ratio is 0.047. The pitch-to-rib height ratio is 10. The results show that the Nusselt number ratios of steam are 1.19–1.32 times greater than those of air over the range of Reynolds numbers studied. For wide aspect ratio channels using steam as the coolant, the 60° angled ribs has the best heat transfer performance and is recommended for cooling design.     

Experimental study on heat transfer of thermally developing and developed, turbulent, horizontal pipe flow of dilute air-solids suspensions

Heat transfer characteristics of a turbulent, dilute air-solids suspension flow in thermally developing/developed regions were experimentally studied, using a uniformly heated, horizontal 54.5 mm-ID pipe and 43-μm-diameter glass beads. The local heat transfer was measured at 27 locations from the inlet to 120-dia downstream of the heated section over a range of Reynolds numbers 3×10⁴−1.2×10⁵ and solids loading ratio 0–3, and the fully developed profiles of air velocity/temperature and particle mass flux were measured at a location 140-dia downstream of the heated section using specially designed probes, inserted into the suspension flow. The effects of the Reynolds number, solids loading ratio, and azimuthal/longitudinal locations on the heat transfer characteristics and their interactions are discussed through comparison of the present results with the data obtained by other investigators. Received on 14 October 1996     

Numerical simulation of fluid flow and heat transfer characteristics in channel with V corrugated plates

A detailed numerical study is carried out to investigate fluid flow and heat transfer characteristics in a channel with heated V corrugated upper and lower plates. The parameters studied include the Reynolds number (Re = 2,000–5,500), angles of V corrugated plates (θ = 20°, 40°, 60°), and constant heat fluxs (q″ = 580, 830, 1,090 W/m²). Numerical results have been validated using the experimented data reported by Naphon, and a good agreement has been found. The angles of V corrugated plates (θ) and the Reynolds number are demonstrated to significantly affect the fluid flow and the heat transfer rate. Increasing the angles of V corrugated plates can make the heat transfer performance become better. The increasing Reynolds number leads to a more complex fluid flow and heat transfer rate. The numerical calculations with a non-equilibrium wall function have a better accuracy than with a standard wall function for solving high Reynolds numbers or complex flow problems.     

Combined radiation and natural convection in a rectangular cavity with a transparent wall and containing a non-participating fluid

This paper describes a numerical method for the study of combined natural convection and radiation in a rectangular, two-dimensional cavity containing a non-participating (i.e. transparent) fluid. One wall of the cavity is isothermal, being heated either by solar radiation or independently. The opposite wall is partially transparent, permitting radiation exchanges between the cavity and its surroundings and/or the Sun; that wall also exchanges heat by convection from its external surface to the surroundings. The other two walls are adiabatic: convection and radiation there are balanced, so that there is no heat transfer through those walls. The equations of motion and energy are solved by finite difference methods. Coupled to these equations are the radiative flux boundary conditions which are used to determine the temperature distribution along the non-isothermal walls. A two-band radiation model has been employed. Results are presented for a square cavity with a vertical hot wall at 150 °C, the ambient at 20 °C and 10⁴ ? Ra ? 3 × 10⁵, in the absence of direct insolation. The effects on the flow and heat transfer in the cavity of radiation and external convection have been examined. More extensive results will be presented in subsequent papers.     

Experimental investigation of mixed convection in a rectangular duct with a heated plate in the middle of cross section

The flow and heat transfer in an inclined and horizontal rectangular duct with a heated plate longitudinally mounted in the middle of cross section was experimentally investigated. The heated plate and rectangular duct were both made of highly conductive materials, and the heated plate was subjected to a uniform heat flux. The heat transfer processes through the test section were under various operating conditions: Pr ≈ 0.7, inclination angle ϕ = −60° to +60°, Reynolds number Re = 334–1,911, Grashof number Gr = 5.26 × 10²–5.78 × 10⁶. The experimental results showed that the average Nusselt number in the entrance region was 1.6–2 times as large as that in the fully developed region. The average Nusselt numbers and pressure drops increased with the Reynolds number. The average Nusselt numbers and pressure drops decreased with an increase in the inclination angle from −60° to +60° when the Reynolds number was less than 1,500. But when the Reynolds number increased to over about 1,800, the heat transfer coefficients and pressure drops were independent of inclination angles.     

Experimental study of convective heat transfer from a rotating finned tube in transverse air flow

 The convective heat transfer from fins to air has been evaluated using rotating annular fins subjected to an air flow parallel to the fins. The fin cooling is studied using infrared thermography. The thermal balance in a fin during its cooling process allows us to obtain the heat transfer coefficient from the temperature time evolution of the fin. Moreover, Particle Image Velocimetry allows us to obtain the flow field in the mid-plane between two fins. The influence of the fin spacing on the convective heat transfer is studied for various velocities of the superposed air flow and various fin rotational speeds. These tests were carried out for air flow Reynolds numbers (based on the shaft diameter and the velocity of the superposed air flow) between 2550 and 18200 and rotational Reynolds numbers (based on the shaft diameter and the peripheral speed) between 800 and 2.9 × 10⁴, for different fin spacings. Received: 14 May 1999/Accepted: 8 October 1999     

Experimental and numerical study on laminar natural convection in a cavity heated from bottom due to an inclined fin

Natural convection heat transfer in an inclined fin attached square enclosure is studied both experimentally and numerically. Bottom wall of enclosure has higher temperature than that of top wall while vertical walls are adiabatic. Inclined fin has also adiabatic boundary conditions. Numerical solutions have been done by writing a computer code in Fortran platform and results are compared with Fluent commercial code and experimental method. Governing parameters are Rayleigh numbers (8.10⁵ ≤ Ra ≤ 4 × 10⁶) and inclination angle (30° ≤ and ≤ 120°). The temperature measurements are done by using thermocouples distributed uniformly at the wall of the enclosure. Remarkably good agreement is obtained between the predicted results and experimental data. A correlation is also developed including all effective parameters on heat transfer and fluid flow. It was observed that heat transfer can be controlled by attaching an inclined fin onto wall.     

Effect of streamwise spacing on periodic and random unsteadiness in a bundle of short cylinders confined in a channel

While flow across long tube bundles is considered classical data, pin-fin arrays made up of short tubes have become a growing topic of interest for use in cooling gas turbine airfoils. Data from the literature indicate that decreasing streamwise spacing increases heat transfer in pin-fin arrays; however, the specific mechanism that causes increased heat transfer coefficients remains unknown. The present work makes use of time-resolved PIV to quantify the effects of streamwise spacing on the turbulent near wake throughout various pin-fin array spacings. Specifically, proper orthogonal decomposition was used to separate the (quasi-) periodic motion from vortex shedding and the random motion from turbulent eddies. Reynolds number flow conditions of 3.0?×?10³ and 2.0?×?10⁴, based on pin-fin diameter and velocity at the minimum flow area, were considered. Streamwise spacing was varied from 3.46 pin diameters to 1.73 pin diameters while the pin-fin height-to-diameter ratio was unity and the spanwise spacing was held constant at two diameters. Results indicated that (quasi-) periodic motions were attenuated at closer streamwise spacings while the level of random motions was not strongly dependent on pin-fin spacing. This trend was observed at both Reynolds number conditions considered. Because closer spacings exhibit higher heat transfer levels, the present results imply that periodic motions may not contribute to heat transfer, although further experimentation is required.     

Experimental study on the pressure drop and heat transfer characteristics of tubes with internal wave-like longitudinal fins

Experiments were performed to determine the heat transfer and pressure drop characteristics in the entrance and fully developed regions of tubes with internal wave-like longitudinal fins. The test tube has a double-pipe structure, with the inner tube as an insertion. The wave-like fins are in the annulus and span its full width. Experiments were conducted for two cases: one with the inner tube blocked (no air flowing through it) and the other with the inner tube unblocked. The outer tube was electrically heated. Local and average heat transfer coefficients and friction factors were measured. The friction factor and Nusselt number correlations in the fully developed region were obtained in the Reynolds number range of 9×10² to 3.5×10³. It has been found that the wave-like fins enhance heat transfer significantly with the blocked case being superior. In addition, the in-tube heat transfer process is characterized by an earlier transition from laminar to turbulent flow and Reynolds number-dependent thermal entrance length. Received on 12 May 1998     

Numerical modelling of confined flow past a cylinder of square cross-section at various orientations

Results are presented for the unsteady, two-dimensional flow and heat transfer due to a square obstruction of diameter d located asymmetrically between the parallel sliding walls of a channel with length-to-height ratio W/H = 6·44. Analysis is based on the numerical solution of spatially and temporally second-order accurate finite difference approximations of the transport equations expressed in curvilinear co-ordinates. Laminar, constant property flow is assumed for obstruction configurations in which the blockage ratio is d/H = 0·192, the nearest-wall distances are g/d = 0·2, 0·5 and 1, the orientation angles are α=0°, 10° and 20° and the Reynolds numbers are Re=100, 500, and 1000. Preparatory testing of the numerical procedure was performed for a variety of documented flows to verify its physiconumerical accuracy and obtain estimates of the residual grid-dependent uncertainties in the variables calculated. Heat transfer, drag and lift coefficients and Strouhal numbers for the present flow were finally calculated to within 4%–7% of their grid-dependent values using non-uniformly spaced grids consisting of (x=99, y=55) nodes. Above a critical value of the Reynolds number, which depends on the geometrical parameters, the flow is characterized by alternate vortex shedding from the obstruction top and bottom surfaces. Streamline, vorticity and particle streakline plots provide qualitative impressions of the unsteady vortical flow. Especially noteworthy are the extremes in the lift coefficient which ranges from large positive values for an obstruction with g/d=0·2 and α=10° to negative values for one with g/d=0·5 and α=0°. Both the drag and lift coefficients as well as the Strouhal number exhibit non-monotonic variations with respect to the parameters explored. Asymmetries in the obstruction location and orientation account for relatively large vortex-induced periodic variations in heat transfer, especially along the wall nearest the obstruction. Notable differences are also predicted for the heat transfer coefficients of the individual obstruction surfaces as a function of the orientation angle.     

Natural convection in partially cooled tilted cavities

Two-dimensional numerical simulations of laminar natural convection in a partially cooled, differentially heated inclined cavities are performed. One of the cavity walls is entirely heated to a uniformly high temperature (heat source) while the opposite wall is partially cooled to a lower temperature (heat sink). The remaining walls are adiabatic. The tilt angle of the cavity is varied from 0° (heated from left) to −90° (heated from top). The fast false implicit transient scheme (FITS) algorithm, developed earlier by the same authors, is modified to solve the derived variables vorticity-streamfunction formulation. The effects of aspect ratio (AR), sink–source ratio and tilt angle on the average Nusselt number are examined through a parametric study; solutions are obtained for two Grashof numbers, 10⁵ and 10⁷. Flow patterns and isotherms are used to investigate the heat transfer and fluid flow mechanisms inside the cavity. © 1998 John Wiley & Sons, Ltd.     

Heat transfer from a surface fitted with rectangular blocks at different orientation angle

 An experimental investigation was carried out to study the enhancement of the heat transfer from a heated flat plate fitted with rectangular blocks of 1 × 2 × 2 cm³ dimensions in a channel flow as a function of Reynolds number (Re_h), spacing (S _y ) of blocks in the flow direction, and the block orientation angle (α) with respect to the main flow direction. The experiments were performed in a channel of 18 cm width and 10 cm height, with air as the working fluid. For fixed S _x =3.81 cm, which is the space between the blocks in transverse to the flow direction, the experimental ranges of the parameters were S _y =3.33–4.33 cm, α=0–45°, Re_h=7625–31550 based on the hydraulic diameter and the average velocity at the beginning of the test section in the channel. Correlations for Nusselt number were developed, and the ratios of heat transfer with blocks to those with no blocks were given. The results indicated that the heat transfer could be enhanced or reduced depending on the spacing between blocks, and the block orientation angle. The maximum heat transfer rate was obtained at the orientation angle of 45°. Received on 13 December 2000 / Published online: 29 November 2001     

Flow and heat/mass transfer in a wavy duct with various corrugation angles in two dimensional flow regimes

In this study, two dimensional heat/mass transfer characteristics and flow features were investigated in a rectangular wavy duct with various corrugation angles. The test duct had a width of 7.3 mm and a large aspect ratio of 7.3 to simulate two dimensional characteristics. The corrugation angles used were 100°, 115°, 130°, and 145°. Numerical analysis using the commercial code FLUENT, was used to analyze the flow features. In addition, the oil-lamp black method was used for flow visualization. Local heat/mass transfer coefficients on the corrugated walls were measured using a naphthalene sublimation technique. The Reynolds number, based on the duct hydraulic diameter, was varied from 700 to 5,000. The experimental results and numerical analysis showed interesting and detailed features in the wavy duct. Main flow impinged on upstream of a pressure wall, and the flow greatly enhanced heat/mass transfer. On a suction wall, however, flow separation and reattachment dominantly affected the heat/mass transfer characteristics on the wall. As the corrugation angle decreased (it means the duct has more sharp turn), the region of flow stagnation at the front part of the pressure wall became wider. Also, the position of flow reattachment on the suction wall moved upstream as the corrugation angle decreased. A high heat transfer rate appeared at the front part of the pressure wall due to main-flow impingement, and at the front part of the suction wall due to flow reattachment. The high heat/mass transfer region by the main-flow impingement and the circulation flow induced at a valley between the pressure and suction walls changed with the corrugation angle and the Reynolds number. As the corrugation angle decreased, the flow in the wavy duct changed to transition to turbulent flow earlier.