Permeability and conductivity of red blood cell templated polyelectrolyte capsules coated with supplementary layers

The permeability of ions and small polar molecules through polyelectrolyte multilayer capsules templated on red blood cells was studied by means of confocal microscopy and electrorotation. Capsules were obtained by removing the cell after polyelectrolyte multilayer formation by means of NaOCl treatment. This procedure results in cross-linking of poly(allylamine hydrochloride) (PAH) molecules and destroying poly(styrene sulfonate) (PSS) within the multilayer. Capsules are obtained being remarkably different from layer-by-layer (LbL) capsules. These capsules are rather permeable for low as well as for high molecular weight species. However, upon adsorption of extra polyelectrolyte layers the permeability decreased remarkably. The assembly of six supplementary layers of PAH and PSS rendered the capsule almost impermeable for fluorescein. Resealing by supplementary layers is a potential means for filling and release control. By means of electrorotation measurements, it was shown that the capsule walls obtained isolating properties in electrolyte solutions. Conclusions are drawn concerning the mechanism of permeability through cell templated polyelectrolyte multilayer capsules.     

Multivalent ion/polyelectrolyte exchange processes in exponentially growing multilayers

We show, in this paper that multivalent ferrocyanide anions can penetrate into exponentially growing (PGA/PAH)n multilayer films whatever the nature of the last deposited layer. These ions are not able to diffuse out of the film when it is brought in contact with a pure buffer solution. However, the contact of this film with a poly(allylamine) (PAH) or a poly(L-glutamic acid) (PGA) solution leads to the release of ferrocyanide ions from the multilayer. It is shown that the release of ferrocyanide anions, when the film is in contact with a PGA solution, is due to the diffusion of the PGA chains into the film so that an exchange between ferrocyanide ions and PGA chains takes place inside the film. On the other hand, PAH chains do not diffuse into PGA/PAH multilayers. When the film is then brought in contact with a PAH solution, the PAH chains from the solution are expected to strongly interact with the ferrocyanide ions and thus induce a diffusion mechanism of the multivalent anions out of the film, the film/solution interface playing the role of a sink for these ions. This work thus shows that interactions between multivalent ions and exponentially growing films are much more complex than expected at first sight and that polyelectrolyte multilayers must be seen as dynamic entities in which diffusion and exchange processes can take place.     

Assembly of poly(N-isopropylacrylamide)-co-acrylic acid microgel thin films on polyelectrolyte multilayers: Effects of polyelectrolyte layer thickness, surface charge, and microgel solution pH

Temperature- and pH-sensitive poly(N-isopropylacrylamide)?Cco-acrylic acid (pNIPAm-co-AAc) microgels were deposited on glass substrates coated with polyelectrolyte multilayers composed of the polycation poly(allylamine hydrochloride) (PAH) and the polyanion poly(sodium 4-styrenesulfonate) (PSS). The microgel density and structure of the resultant films were investigated as a function of: (1) the number of PAH/PSS layers (layer thickness); (2) the charge on the outer layer of the polyelectrolyte multilayer film; and (3) the pH of microgel deposition solution. The resultant films were studied by differential interference contrast optical microscopy, atomic force microscopy, and scanning electron microscopy. It was found that the coverage of the microgels on the surface was a complex function of the pH of the deposition solution, the charge on the outer layer of the polyelectrolyte thin film and the PAH/PSS layer thickness; although it appears that microgel charge plays the biggest role in determining the resultant surface coverage.     

Enhanced Salt Tolerance of Polyurethane Based Multilayer Films

In our previous study, polyurethane (PU) based multilayer films assembled with weak polyelectrolytes exhibited controllable loading and release properties, but would be decomposed in high salt solution. Herein, a strong polyelectrolyte, poly(styrene sulfonic acid) sodium (PSS), was introduced to fabricate multilayer films. The salt tolerance of the film was investigated by evaluating the loading and release profiles towards model drug in salt solution with different concentrations. Results showed that the release behavior of the film, as well as its loading capacity, can be tuned by varying the salt concentrations. And the film showed a good salt tolerance that can remain integrity even after 6 cycles of drug loading and release in 600 mmol·L^?1 NaCl solution. It showed that the salt tolerance of PU based films can be greatly improved through assembling with strong polyelectrolyte.     

Correlation of antithrombogenicity and heat treatment for layer-by-layer self-assembled polyelectrolyte films

Antithrombogenic films with high durability were fabricated in a wet process. Antithrombogenicity was achieved with polyelectrolyte multilayer thin film prepared from poly(vinyl alcohol)-poly(acrylic acid) (PVA-PAA) blends, deposited in alternate layers with poly(allylamine hydrochloride) (PAH). Film durability, assessed by abrasion resistance and water resistance, was enhanced by forming cross-links via amide bonds induced by heat treatment of the film. The film was found to be resistant to protein adsorption, as measured by the amount of fibrinogen adsorbed from an aqueous solution. The antithrombogenic efficacy was assessed in ex vivo experiments by the ability of stainless steel mesh, coated with the polyelectrolyte and inserted into a pig blood vessel, to inhibit thrombus formation. Mesh coated with the polyelectrolyte did not reduce blood flow over a period of 15 min, whereas with uncoated mesh blood flow stopped within 6 min because of blood vessel blockage by thrombus formation.     

Room-temperature imprinting poly(acrylic acid)/poly(allylamine hydrochloride) multilayer films by using polymer molds

Layer-by-layer assembled polyelectrolyte multilayer films of poly(acrylic acid) (PAA)/poly(allylamine hydrochloride) (PAH) have been successfully patterned by room-temperature imprinting using a Norland Optical Adhesives (NOA 63) polymer mold. The proper amount of water in the PAA/PAH multilayer film can decrease the viscosity of the film and facilitate the imprinting. Many factors, such as imprinting pressure, length of imprinting time, and the structure and size of the patterns in the polymer mold, can produce an influence on the final imprinted pattern structures on multilayer films. A high imprinting pressure of 100 bar and elongated imprinting time of several hours is needed to achieve a patterned PAA/PAH multilayer film with a feature size of several tens of micrometers. With a twice imprinting, grid structures can be successfully produced when a NOA 63 mold having line structures is used. Room-temperature imprinting by using polymer NOA 63 mold provides a facile way to fabricate layered polymeric films with various kinds of pattern structures.     

Polymer-Based Superhydrophobic Coating Fabricated from Polyelectrolyte Multilayers of Poly(allylamine hydrochloride) and Poly(acrylic acid)

Superhydrophobic films mainly based on poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) polyelectrolyte multilayer have been deposited onto cleaned glass substrate by a layer-by-layer dip coating method. 3 bilayers of the PAH and PAA was directly coated onto the substrate as an underlying layer for subsequent coating. Desired surface roughness on the polyelectrolyte bilayers was created by etching the bilayers in hydrochloric acid solution so as to create the open pore having suitable size at the surface. Then, nanoparticles such as SiO₂ and TiO₂ of various sizes were deposited onto the etched polyelectrolyte bilayers. Finally, the surfaces were further modified with semifluorinated silane followed by cross-linking at 180 °C for 2 h to obtain desirable surface morphological features. The effect of etching time and addition of nanoparticles on surface morphology was investigated using an atomic force microscope (AFM). Wetting ability of the prepared film was determined by measuring water droplet contact angle using a goniometer. Adhesion between the superhydrophobic films and the substrate was evaluated by using a standard tape test method (D3359). The adhesion was improved by reducing the organic content in the films.     

Fabrication of Covalently Linked PAH/PVS Layer-by-layer Assembled Multilayers via a Post-photochemical Cross-linking Strategy

A post-photochemical cross-linking strategy was successfully demonstrated to enhance the stability of polyelectrolyte poly(allylamine hydrochloride)(PAH)/poly(vinylsulfonic acid sodium salt)(PVS) multilayers. Conventional polyelectrolyte multilayers of PAH/PVS are usually fabricated through electrostatic layer-by-layer(LbL) assembly, resulting in poor stability, especially in basic solutions, which leads to the urgent demand for converting weak electrostatic interactions into covalent bonds to enhance the stability of the multilayers. This stability problem has been ultimately addressed by post-infiltrating a photosensitive cross-linking agent, 4,4'-diazostilbene-2,2'- disulfonic acid disodium salt(DAS), into the LbL assembled films to initiate the photochemical reaction to cross-link the multilayers. The obviously improved stability of the photo-cross-linked multilayers was demonstrated through experiments with basic solution treatments. Compared to the complete decomposition of uncross-linked multilayers in basic solution, over 74.4% of the covalently cross-linked multilayers were retained under the same conditions, even after a longer duration of basic solution treatment.     

Facile method for the fabrication of robust polyelectrolyte multilayers by post-photo-cross-linking of azido groups

In this letter, we have developed a facile method to enhance the stability of polyelectrolyte multilayers. We fabricate conventional polyelectrolyte multilayers of PAH/PAA through electrostatic layer-by-layer (LbL) assembly and then postinfiltrate photosensitive cross-linking agent 4,4'-diazostilbene-2,2'-disulfonic acid disodium salt into the LbL films. After cross-linking by UV irradiation, the stability of the photo-cross-linked multilayer is highly improved as evidenced by the lack of dissolution under ultrasonication in saturated SDS aqueous solutions for 10 min. Moreover, by taking advantage of the different stability of the LbL film before and after UV irradiation, a patterned surface can be achieved.     

Dynamics of counterions in polyelectrolyte multilayers studied by electro-optics

The electro-optical behavior of a multilayer constructed via layer-by-layer deposition of poly(sodium 4-styrenesulfonate) (PSS) and poly(allylamine hydrochloride) (PAH) onto ellipsoidal β-FeOOH particles is examined using electric light scattering method. For fully charged polymers (at pH 4.5), the electro-optical effect is found to increase with polyelectrolyte layer number, showing a tendency to saturation in the linear growth regime. The effect is greater and of lower frequency of relaxation for the films ending with PAH in comparison to those with top PSS layer. Evidence is given that polarization of “condensed” counterions along the chains of the last-adsorbed polymer is mainly responsible for the observed electro-optical behavior of the polyelectrolyte multilayer. Although incorporation of “condensed” small ions into the film bulk seems probable for the PSS/PAH multilayer, their participation in the electro-optical effect is found negligible. The structural changes in the PSS/PAH multilayer due to the PAH deprotonation at pH 7.5 and the corresponding changes in the electro-optical effect confirm the key role of the last-adsorbed polymer for the behavior of the entire PSS/PAH film.     

Assembly of multilayer films from polyelectrolytes containing weak and strong acid moieties

Multilayer films were assembled from a copolymer containing both weakly and strongly charged pendant groups, poly(4-styrenesulfonic acid-co-maleic acid) (PSSMA), deposited in alternation with poly(allylamine hydrochloride) (PAH). The strongly charged groups (styrene sulfonate, SS) are expected to form electrostatic linkages (to enhance film stability), while the weakly charged groups (maleic acid, MA) can alter multilayer film properties because they are responsive to external pH changes. In this study, we varied several assembly conditions such as pH, SS/MA ratio in PSSMA, and the ionic strength of the polyelectrolyte solutions. The multilayer films were also treated by immersion into pH 2 and 11 solutions after assembly. Quartz crystal microgravimetry and UV-visible spectrophotometry showed that the thickness of PSSMA/PAH multilayers decreases with increasing assembly pH regardless of whether salt was present in the polyelectrolyte solutions. When no salt was added, the multilayers are thinner, smoother, and grow less regularly. Atomic force microscopy images indicate that the presence of salt in polyelectrolyte solutions results in rougher surface morphologies, and this effect is especially significant in multilayers assembled at pH 2 and pH 11. When both polyelectrolytes are adsorbed at conditions where they are highly charged, salt was necessary to promote regular multilayer growth. Fourier transform infrared spectroscopy studies show that the carboxylic acids in the multilayers are essentially ionized when assembled from different pHs in 0.5 M sodium chloride solutions, whereas some carboxylic acids remain protonated in the multilayers assembled from solutions with no added salt. This resulted in different pH stability regimes when the multilayers were exposed to different pH solutions, post assembly.     

Polyelectrolyte blend multilayer films: surface morphology, wettability, and protein adsorption characteristics

We report the influence of polyelectrolyte (PE) multilayer films prepared from poly(styrene sulfonate)-poly(acrylic acid) (PSS-PAA) blends, deposited in alternation with poly(allylamine hydrochloride) (PAH), on film wettability and the adsorption behavior of the protein immunoglobulin G (IgG). Variations in the chemical composition of the PAH/(PSS-PAA) multilayer films, controlled by the PSS/PAA blend ratio in the dipping solutions, were used to systematically control film thickness, surface morphology, surface wettability, and IgG adsorption. Spectroscopic ellipsometry measurements indicate that increasing the PSS content in the blend solutions results in a systematic decrease in film thickness. Increasing the PSS content in the blend solutions also leads to a reduction in film surface roughness (as measured by atomic force microscopy), with a corresponding increase in surface hydrophobicity. Advancing contact angles (theta) range from 7 degrees for PAH/PAA films through to 53 degrees for PAH/PSS films. X-ray photoelectron spectroscopy measurements indicate that the increase in film hydrophobicity is due to an increase in PSS concentration at the film surface. In addition, the influence of added electrolyte in the PE solutions was investigated. Adsorption from PE solutions containing added salt favors PSS adsorption and results in more hydrophobic films. The amount of IgG adsorbed on the multilayer films systematically increased on films assembled from blends with increasing PSS content, suggesting strong interactions between PSS in the multilayer films and IgG. Hence, multilayer films prepared from blended PE solutions can be used to tune film thickness and composition, as well as wetting and protein adsorption characteristics.     

Interactions between multivalent ions and exponentially growing multilayers: dissolution and exchange processes

The interactions between multivalent ions (small ions or polyelectrolytes) and two exponentially growing polyelectrolyte multilayers, namely, (HA-PLL)(n)() and (HA-PAH)(n)() films, are investigated (HA = hyaluronic acid, PLL = poly-l-lysine, PAH = poly(allylamine)). Ferrocyanide and ferricyanide ions are used as small ion probes. The most striking finding is that, even though these two ions differ only by one charge unit, the ferrocyanide ions induce a partial dissolution of both multilayers whereas these films remain stable in the presence of ferricyanide ions. The dissolution process of (HA-PLL)(n)() films is more rapid than that of (HA-PAH)(n)() films, indicating a stronger interaction between HA and PAH compared to HA and PLL. This is confirmed by polyelectrolyte exchange experiments: when an (HA-PLL)(n)() multilayer film is put into contact with a PAH solution, PLL is quantitatively exchanged with the PAH chains and transformed into an HA-PAH film, whereas an (HA-PAH)(n)() multilayer remains stable in the presence of a PLL solution.     

Nonlithographic micro- and nanopatterning of TiO2 using polymer stamped molecular templates

The polymer-on-polymer stamping technique was used to template patterned TiO2 onto polymer thin films. Polystyrene-b-polyvinyl pyridine diblock copolymer (PS-b-PVP) was stamped on a layer-by-layer assembled thin film of poly(allylamine hydrochloride) and poly(acrylic acid). After rinsing the surface with a good solvent for the block copolymer, an adsorbed PS-b-PVP monolayer remained on the polyelectrolyte film, resulting in a pattern of alternating hydrophobic and carboxylic acid containing hydrophilic regions. The surface was used as a template for the selective deposition of TiO2 on the multilayer surface, using an acid-catalyzed hydrolysis of(NH4)2TiF6. Using this novel approach, we have successfully demonstrated the patterning of TiO2 film on a polyelectrolyte multilayer. Finally, nanoscale features consisting of 200 nm lines alternating with a 350 nm period was accomplished. This paper represents the first such attempt to create an all-polymer nonlithographic template for the directed deposition of TiO2 or related metal oxides; this technique, which utilizes the versatile polyelectrolyte multilayer process, enables the construction of complex polymer-inorganic microstructures suitable for electrooptical and photonic applications.     

Controllable exploding microcapsules as drug carriers

Controllable exploding polyelectrolyte microcapsules were developed by layer-by-layer assembly of poly(allylamine hydrochloride) (PAH) and poly(sodium 4-styrenesulfonate) (PSS) on a dextran microgel core containing a cleavable disulfide bond fabricated via click chemistry. The microcapsules can explode upon the injection of DTT with an explosive release of the drug.     

Modulation of the functions of osteoblast-like cells on poly(allylamine hydrochloride) and poly(acrylic acid) multilayer films

Deposition of layer-by-layer polyelectrolyte multilayer (PEM) films has been a widely applied surface modification technique to improve the biocompatibility of biomaterials. The objective of this study was to investigate the impact of the deposition of poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) multilayer films on adhesion, growth and differentiation of osteoblasts-like MG63 cells. PAH and PAA were deposited sequentially onto tissue culture polystyrene at either pH 2.0 or pH 6.5 with 4-21 layers. While the MG63 cells attached poorly on the PAH/PAA multilayer films deposited at pH 2.0, while the cells adhered to the PEM films deposited at pH 6.5, depending on layer numbers. Cell adhesion, proliferation and osteogenic activities (alkaline phosphatase activity, expression of osteogenic marker genes and mineralization) were highest on the 4-layer PAH/PAA film and decreased with increasing layer numbers. On the other hand, the behavior of MG63 cells did not show any difference on the adjacent even and odd layers, except PEM4 and PEM5, i.e. the surface charges of the PAH/PAA multilayer films with over ten layers seem indifferent to osteoblastic functions. The results in this study suggested that the mechanical properties of PEM films may play a critical role in modulating the behavior of osteoblasts, providing guidance for application of PEM films to osteopaedic implants.     

Surface interactions during polyelectrolyte multilayer build-up. 2. The effect of ionic strength on the structure of preformed multilayers

Interactions between surfaces bearing multilayer films of poly(allylamine hydrochloride) (PAH) and poly(styrenesulfonate sodium salt) (PSS) were investigated across a range of aqueous KBr solutions. Three layer films (PAH/PSS/PAH) were preassembled on mica surfaces, and the resulting interactions were measured with the interferometric surface force apparatus (SFA). Increasing the ionic strength of the medium resulted in a progressive swelling of the multilayer films. Interactions in solutions containing more than 10(-3) M KBr were dominated by a long-ranged steric repulsion originating from compression of polyelectrolyte segments extending into solution. In 10(-1) M KBr, repeated measurements at the same contact position showed a considerable reduction of the range and the strength of the steric force, indicating a flattening of the film during initial approach. Furthermore, this flattening was irreversible on the time scale of the experiments, and measurements performed up to 72 h after the initial compression showed no signs of relaxation. These studies aid in understanding the dominant interactions between polyelectrolyte multilayers, including polyelectrolyte films deposited on colloidal particles, which is important for the preparation of colloidally stable nanoengineered particles.     

pH-sensitive bipolar ion-permselective ultrathin films

pH-Sensitive bipolar ion-permselective films of polyelectrolyte multilayers were prepared by layer-by-layer (LbL) assembly and photo-cross-linking of benzophenone-modified poly(acrylic acid) (PAA-BP) and poly(allylamine hydrochloride) (PAH-BP). The multilayer structure and ionizable group composition was finely tuned by changing the pH of the dipping solution. This structure and composition was in turn "preserved" by photo-cross-linking, forming highly stable membrane films. Since PAA-BP and PAH-BP are weak polyelectrolytes, it is possible to control the number of unbound, un-ionized -COOH or -NH2 groups in the multilayer by changing the pH. Moreover, the pH of the deposited film also plays an important role in determining selective latter permselectivity. For example, PAA-BP/PAH-BP multilayers deposited from two pH conditions, pH = 3 (PAA-BP) and pH = 6 (PAH-BP), showed pH-switchable permselectivity for both cationic (pH = 10) and anionic (pH = 3) probe molecules in a single film. The system offers advantages in film stability and introducing reversible selective ion permeability over previous multilayer film and cross-linking methods.     

Creating effective refractive index gradients within polyelectrolyte multilayer films: molecularly assembled rugate filters

We demonstrate the use of aqueous-based layer-by-layer (LbL) processing and in situ nanoreactor chemistry for creating polyelectrolyte multilayer (PEM) nanocomposites in which the concentration of a nanoparticle species is modulated throughout the depth of the film in a complex way. Using the in situ growth of silver nanoparticles to selectively increase the refractive index of precisely defined regions of the PEM film, we have produced a digitized rugate filter, a special type of dielectric mirror possessing many thin layers that approximate a continuous, periodic refractive index profile. The design of the digital rugate from an initial smooth index profile was aided by a computer, and construction of the device was accomplished entirely by automated means. Poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) bilayer regions within the film supported subsequent nanoreactor chemistry and created the high refractive index regions of the film, while PAH and poly(styrenesulfonate) (PSS) bilayer regions remained unmodified and served as the low index regions. Spectroscopic results obtained from the assembled device confirm the presence of a reflection band that grows in amplitude with increasing silver incorporation, reaching a peak reflectance of 75% after five silver loading and exchange cycles. The rugate structure suppresses reflection sidebands, features common to Bragg reflectors and simpler dielectric mirror designs. Cross-sectional TEM reveals nanoscale control of the size and location of silver-containing domains within the PEM film. The ability of this method to control the placement of nanoparticles within PEMs enables the inexpensive, easy production of conformable optical coatings with tunable properties. In addition, these nanocomposite films may have applications in a number of other fields where precise control of effective gradients in physical properties throughout thin films has been shown to affect the overall performance in a desirable way.     

Sustained release control via photo-cross-linking of polyelectrolyte layer-by-layer hollow capsules

We describe the formation and permeability of polyelectrolyte multilayer hollow-shell capsules by photo-cross-linking and controlled-release (fluorescence) studies. The hollow shells were prepared by alternate layer-by-layer (LbL) adsorption of photo-cross-linkable benzophenone modified poly(allylamine hydrochloride) and poly(sodium 4-styrenesulfonate) on polystyrene particles, followed by removing the core with tetrahydrofuran. Zeta potential measurements, fourier transform infrared spectroscopy, and transmission electron microscopy were used to verify the LbL process integrity. A model drug, rhodamine B (RB), was successfully loaded into the polyelectrolyte hollow capsules. The release kinetics of RB was investigated using fluorescence spectroscopy. The permeability of RB through the hollow shells was effectively controlled based on UV irradiation time. It was shown that the release of RB molecules can be controlled by the degree of cross-linking induced in the multilayer.