Role of the TiO6 octahedra on the ferroelectric and piezoelectric behaviour of the poled PbMg1/3Nb2/3O3-xPbTiO3 (PMN-PT) single crystal and textured ceramic

Field cooling (FC) poled/unpoled PMN-29%PT single crystal and room temperature (RT) poled/unpoled PMN-34.5%PT textured ceramic were investigated between ∼0 and 300 °C by thermal expansion, dielectric and Raman spectroscopy. New phase transitions are evidenced at 40, 91 and 180 °C in the case of FC PMN-29%PT as well as at 70 and 200 °C for RT PMN-34.5%PT and their order is discussed. The physical properties of the textured ceramics are rather similar to the ones observed for the single crystals that make them low-cost alternative for a wide range of applications. However, the temperatures and character of the phase transitions strongly depend on the kind of the poling conditions. Temperature dependences of the Raman line parameters show that the NbO₆ octahedra remain stable during temperature increase, while TiO₆ ones evolve quasi-continuously. The step transitions of the Pb²⁺ ion sublattice are evidenced. This suggests that the TiO₆ and Pb²⁺ sublattices are especially coupled. The role of the TiO₆ clusters on the structural phase transitions and dielectric properties of the PbMg_1/3Nb_2/3O₃-xPbTiO₃ (PMN-PT) system is discussed. The presence of the Raman modes above the maximum dielectric permittivity reveals that the local symmetry is lower than the cubic one (Pm3m). The decrease of the Raman line intensities vs. temperature indicates precisely the continuous evolution of the local symmetry towards the cubic one. The temperature evolution of the Rayleigh wing parameters appears sensitive to the phase transitions’ presence.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

A comparative study of dielectric and Raman spectroscopy of Pb(Y b1/2Ta1/2)O3 and Pb(Y b1/2Nb1/2)O3

A comparative study of the properties of two highly ordered lead based complex perovskites Pb(Y b_1/2Ta_1/2)O₃ and Pb(Y b_1/2Nb_1/2)O₃ has been carried out through x-ray diffraction, dielectric and Raman scattering measurements. These two compounds differ significantly in their structure, dielectric response and phonon vibration although the ionic radii and valencies are same for Ta and Nb. The room temperature x-ray diffraction pattern and Raman spectra show that the symmetry of lead ytterbium tantalate is lower than that of lead ytterbium niobate. The Raman spectra of Pb(Y b_1/2Ta_1/2)O₃ also indicates the presence of local distortion in the lattice which may be one of the factors responsible for the existence of a secondary transition.     

Detailed infrared spectroscopic study of thermal transitions in new hybrid [(CH3)2CHNH3]4Cd3Cl10 crystal

Phase transitions of tetra(isopropylammonium)decachlorotricadmate(II) [(CH₃)₂CHNH₃]₄Cd₃Cl₁₀ crystal have been studied by infrared, far infrared and Raman measurements in wide temperature range, between 11 K and 388 K. The temperature changes of wavenumber, center of gravity, width and intensity of the bands were analyzed to clarify cationic and anionic contributions to the phase transitions mechanism. The results of investigation showed earlier by differential scanning calorimetry (DSC), thermal expansion and dielectric measurements clearly confirmed the sequence of phase transitions at T₁=353 K, T₂=294 K and T₃=260 K. The current results derived from DSC and infrared measurements revealed additional phase transition at T₄=120 K.     

Relationship between phase structure and electrical properties of (K0.5Na0.5)NbO3-LiTaO3 lead-free ceramics

Lead-free piezoelectric ceramics of (1−x)K_0.5Na_0.5NbO₃-xLiTaO₃ (KNN-LT) system have been investigated in this work. X-ray diffraction, Raman spectra measurements, DSC (Differential Scanning Calorimetric), and dielectric constant versus temperature provide direct evidence that the phase transition temperature between tetragonal and orthorhombic shift to lower temperature with the increasing of LT content. The KNN-0.05LT ceramics exhibit the highest high-field d₃₃ up to 220 pm/V. At the same time, we also investigated the relationship between phase structure and electric properties, showing that the orthorhombic phase presents better piezoelectric temperature stabilities than the tetragonal phase. The result may provide a new way for KNN-based lead-free ceramics.     

Dielectric and impedance measurements on (1−x)Ba(Fe1/2Ta1/2)O3-xBa(Zn1/3Ta2/3)O3 ceramics

In this work, ((1−x)Ba(Fe_1/2Ta_1/2)O₃-xBa(Zn_1/3Ta_2/3)O₃), ((1−x)BFT-xBZT) ceramics with x = 0.00–0.12 were synthesized by the solid–state reaction method. X-ray diffraction data revealed that both the powders and ceramics were of a pure-phase cubic perovskite structure. All ceramics showed large dielectric constants. For the x = 0.12 sample, a very high dielectric constant (>20,600) was observed. A lowering in the dielectric loss compared to pure BFT ceramics was observed with the BZT addition. The impedance measurements indicated that BZT has a strong effect on the bulk grain and grain boundary resistance of BFT ceramics. These results are in agreement with the measured dielectric properties. Based on dielectric and impedance results, (1−x)BFT-xBZT ceramics could be of great interest for high performance dielectric materials applications due their giant dielectric constant behavior.     

Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Evolution from relaxor-like dielectric to ferroelectric in Ba[(Fe0.5Nb0.5)1−xTix]O3 solid solutions

Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ (x=0.2,0.4,0.6,0.8,0.85,0.9 and 0.95) solid solutions were synthesized by a standard solid-state reaction technique. X-ray diffraction at room temperature and dielectric characteristics over a broad temperature and frequency range were evaluated systematically. The structure of Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ solid solutions changed from cubic to tetragonal with increasing x. A Debye-like dielectric relaxation following the Arrhenius law similar to that in Ba(Fe_0.5Nb_0.5)O₃ was observed at lower temperature in the composition range 0.2≤x≤0.8, while the relaxor ferroelectric, diffused ferroelectric and normal ferroelectric behavior were observed for x=0.85,0.9 and 0.95, respectively. The process of the evolution of relaxor-like dielectric to ferroelectric suggested the changing from dilute polar micro-domains to polar micro-domains, polar micro/macro-domains and then polar macro-domains in the present ceramics.     

Structural and dielectric properties in the (Ba1−xCax)(Ti0.95Zr0.05)O3 ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.95Zr_0.05)O₃ (x = 0.05-0.40) (BCZT) ceramics were prepared by solid-state reaction technique. XRD results show that the samples in the composition range of 0.05 ≤ x ≤ 0.25 exhibit pure perovskite structures and undergo a polymorphic phase transitions from orthorhombic to tetragonal phase around room temperature. The biphasic structures are detected at x ≥ 0.30 and the dielectric peaks become broad and dielectric constants decrease with increasing Ca content. Ca replacement at Ba site leads to diffuseness, whereas Ca occupancy at Ti site leads to decrease of the T_c.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Structural and electrical behavior of Pb(Mg1/4Cd1/4Mo1/2)O3 ceramics

Preliminary X-ray structural analysis of polycrystalline Pb(Mg_1/4Cd_1/4Mo_1/2)O₃ ceramics, prepared by a solid-state reaction technique, provides single-phase orthorhombic structure at room temperature. Detailed dielectric studies of the material as a function of temperature reveal a sharp phase transition at temperature T_c=49°C obeying Curie-Weiss behavior. Scanning electron microscope (SEM) studies of the sample show the uniform distribution of grains in the samples. A dielectric anomaly and ferroelectric phase transition observed at 49°C was supported by polarization studies. The activation energy of the sample was calculated from the dielectric data. The variation of dc resistivity with temperature suggests that the compound behaves as a negative temperature coefficient resistor (NTCR).     

Phase transformation in (0.90−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3-0.10PbZrO3 piezoelectric ceramic: X-ray diffraction and Raman investigation

Piezoelectric ceramics with compositions of (0.90−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃-0.10PbZrO₃, x=0.28, 0.31, 0.34, 0.37, 0.40 and 0.43, were prepared using the conventional columbite precursor method, and their structural phase transformation and piezoelectric behaviors near the morphotropic phase boundary (MPB) have been systematically investigated as a function of PbTiO₃ content. X-ray diffraction (XRD) results demonstrate that the structure of the ceramics experiences a gradual transition process from rhombohedral phase to tetragonal phase with the increasing of PbTiO₃ content, and that compositions with x=0.34-0.40 lie in the MPB region of this ternary system. A Raman spectra investigation of the ceramic samples testified to the transformation process of rhombohedral phase to tetragonal phase by comparing the relative intensities of tetragonal E(2TO₁) mode and rhombohedral phase R_h mode. The structure information was also correlated to the parabola change of the piezoelectric constant; the maximum piezoelectric constants were obtained near the MPB region.     

Magnetic ordering and instability investigation of multiferroic Pb(Fe2/3W1/3)O3 ceramics by microwave dielectric spectroscopy

The microwave dielectric and magnetic properties of Pb(Fe_2/3W_1/3)O₃ multiferroic ceramics were investigated. A dielectric dispersion occurring in the frequency range 100 MHz-3 GHz and in a broad temperature range showed itself to be a powerful tool to detect magnetostrictive effects. The experimental results revealed the following remarkable features: the temperature dependence of f_R (characteristic frequency) and the dielectric strength Δε (characteristic of the dispersion) enabled us to identify not only the para-ferroelectric (T_C≈180 K) but also the para-antiferromagnetic (T_N≈340 K) phase transitions, while magnetic measurements revealed the para-antiferromagnetic ordering and a weak superexchange interaction (T_N2∼15 K). Additionally, both characterizations confirmed the existence of structural or magnetic instabilities around 250 K.     

Electromechanical properties and dielectric behavior of (Bi1/2Na1/2)(1−1.5x)BixTiO3 lead-free piezoelectric ceramics

Bismuth doped bismuth sodium titanate ceramics [(Bi_1/2Na_1/2)_(1−1.5x)Bi_xTiO₃, x=0 to 0.06] were prepared, and the resulting effects on the microstructure and dielectric properties were examined. All of the Bi-doped ceramics exhibited a single phase of perovskite structure with rhombohedral symmetry. The poling leakage current was significantly reduced by the doping of Bi, facilitating the poling process of the ceramics. The doping with Bi enhances the piezoelectric properties and increases the dielectric constant and the dielectric loss of the ceramics. At 2 mol% Bi-doping level, the ceramics exhibit a large remanent polarization of 47 μC/cm² and a relatively low coercive field of 71 kV/cm, while their d₃₃ and k_p reach a maximum value of 95 pC/N and 21%, respectively.     

Investigation on optical transmission spectra of (1−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 single crystals

The optical transmission spectra from 0.3 to 11 μm of relaxor ferroelectric single crystals (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN-xPT) were systematically studied at room temperature in this paper. The crystal is transparent between 0.45 and 5.5 μm and becomes completely absorbing around 0.4 μm in near UV region and 10 μm in infrared region. But the wavelength cutoff in near UV is much sharper than the long wavelength cutoff. As compared with other configurations, tetragonal single crystals possess the optimal transmission properties. The optical transmittance in the wavelength region from 0.45 to 5.5 μm is about 70%. The results show that tetragonal PMN-xPT single crystals are promising for a wide range of optical applications. Some discussions about the oxygen-octahedra structure that determines the basic energy level of the crystals are also presented on the optical properties of PMN-xPT single crystals.     

Phase diagrams and dielectric response of epitaxial (BaxSr1−x)TiO3 ultrathin films: A first-principles study

A method based on first-principles calculations was used to construct temperature versus misfit strain phase diagrams for epitaxial (Ba_xSr_1−x)TiO₃ ultrathin films over the entire composition range from x=0 to x=1. The predicated phase diagrams show “topologies” that are similar to those calculated by Shirokov et al. (Phy. Rev. B. 79 (2009) 144118), but with quantitative differences that are examined and explained. The dependence of the dielectric permittivity on the misfit strain and the film composition at room temperature are also investigated and compared with available theoretical predications and experimental measurements.     

Dielectric and piezoelectric properties of lead-free (Na0.5K0.5)NbO3-SrTiO3 ceramics

In this article, we report successful preparation of dense [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ (x=0.005-0.100) ceramics by ordinary sintering in air. The dependence of phase structure on doping content of SrO and TiO₂ has been determined by the X-ray diffraction technique. It was found that the crystal structure changed from orthorhombic to tetragonal at x≈0.040. Dielectric study revealed that the dielectric relaxor behavior was induced by doping of SrO and TiO₂ into (Na_0.5K_0.5)NbO₃. The samples in the composition range from x=0.005 to 0.020 exhibited excellent electrical properties, piezoelectric constant of electromechanical planar and thickness coupling coefficients of k_p=26.6-32.5% and k_t=39.8-43.8%. The results show that the [(Na_0.5K_0.5)_1−xSr_x](Nb_1−xTi_x)O₃ ceramics are one of the promising lead-free materials for electromechanical transducer applications.     

Interrelation of antiferrodistortive and ferroelectric phase transitions in Sr1−xAxTiO3 (A=Ba, Pb)

A dielectric and ultrasonic velocity study of antiferrodistortive and ferroelectric phase transitions in Sr_1−xA_xTiO₃ (A=Ba, Pb) is reported. It is shown that both phase transitions co-exist at x<0.03 but at the higher concentration the ferroelectric phase transition entirely suppresses the antiferrodistortive phase transition. The experimentally obtained phase diagrams are discussed in the framework of the Landau phenomenological theory.     

Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Phase formation and dielectric phase transition in Ba1−xCaxTi0.6Zr0.4O3 solid solutions

Perovskite types Ba_1−xCa_xTi_0.6Zr_0.4O₃ (with x=0.0-0.5) ceramics have been prepared through solid state reaction route. The room temperature XRD study suggests the compositions with x=0.0 and x=0.1 have single phase cubic symmetry. With further increase in Ca content, solid solution breaks and an orthorhombic CaTiO₃ like phase is developed. The dielectric study on single phase compositions (x=0.0 and 0.1) reveals that the materials are of relaxor type and undergo a diffuse type ferroelectric phase transition. In the Ca containing composition higher transition temperature is observed than the pure BaTi_0.6Zr_0.4O₃ materials. In the paraelectric region (above T_c) lower diffusivity is observed in the Ca containing composition. The strength of relaxation is calculated and found to be more in Ca containing material than that of pure BaTi_0.6Zr_0.4O₃ composition.