Morphologically controlled preparation of CuO nanostructures under ultrasound irradiation and their evaluation as pseudocapacitor materials

Various morphologies of copper oxide (CuO) nanostructures have been synthesized by controlling the reaction parameters in a sonochemical assisted method without using any templates or surfactants. The effect of reaction parameters including molar ratio of the reactants, reaction temperature, ultrasound exposure time, and annealing temperature on the composition and morphology of the product(s) has been investigated. The prepared samples have been characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDAX), and thermogravimetric analysis (TGA). It has been found that Cu₂(OH)₃NO₃ nanoplatelets are achieved in mild conditions which can be then converted to various morphologies of CuO nanostructures by either using high concentrations of OH⁻ (formation of nanorods), prolonging sonication irradiation (nanoparticles), or thermal treatment (nanospheres). Application of the prepared CuO nanostructures was evaluated as supercapacitive material in 1 M Na₂SO₄ solution using cyclic voltammetry (CV) in different potential scan rates ranging from 5 to 100 mV s⁻¹. The specific capacitance has been calculated using CV curves. It has been found that the pseudocapacitor performance of CuO can be tuned via employing morphologically controlled samples. Accordingly, the prolonged sonicated sample (nanoparticles) showed the high specific capacitance of 158 F.g⁻¹.     

Preparation and characterization of slice-like Cu2(OH)3NO3 superhydrophobic structure on copper foil

Superhydrophobic structure was prepared on copper foil via a facile solution-immersion method. Thus slice-like Cu₂(OH)₃NO₃ crystal was prepared on the surface of the copper foil by sequential immersing in an aqueous solution of sodium hydroxide and cupric nitrate. And the superhydrophobic structure was obtained by modifying the slice-like Cu₂(OH)₃NO₃ crystal with 1H,1H,2H,2H-perfluorodecyltriethoxysilane (FAS-17). The morphologies, chemical compositions and states, and hydrophobicity of the surface-modifying films on the copper foil substrates were analyzed by means of scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and water contact angle measurement. Moreover, the thermal stability of the slice-like structure was also evaluated using thermogravimetric analysis (TGA). It was found that roughening of the copper foil surface helped to increase the hydrophobicity to some extent, but no superhydrophobicity was obtained unless the slice-like Cu₂(OH)₃NO₃ crystal formed on the Cu substrate was modified with 1H,1H,2H,2H-perfluorodecyltriethoxysilane. Besides, the superhydrophobicity of the FAS-17-modified slice-like Cu₂(OH)₃NO₃ structure was closely related to the surface morphology. And this hydrophobic structure retained good superhydrophobic stability at elevated temperature and in long-term storage as well, which should be critical to the application of Cu-matrix materials in engineering.     

Ultrasound assisted synthesis of {[Cu2(BDC)2(dabco)].2DMF.2H2O} nanostructures in the presence of modulator; new precursor to prepare nano copper oxides

As a new precursor to prepare nano copper oxide, nanostructures of porous metal organic framework (MOF) {[Cu₂(BDC)₂(dabco)].2DMF.2H₂O} (1) have been synthesized in the presence of acetic acid as a modulator via sonochemical method. Different concentrations of metal ion, organic linkers, modulator reagent and also different sonication times were held to improve the quality of nanostructures. Ultrasound irradiation helps nucleation step of the oriented attachment of modulation method and nanoparticles with a few nanorods has been prepared. As prepared MOF was calcinated at 500 °C to prepare nano CuO and Cu₂O. Compound 1, CuO and Cu₂O nanostructures were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray powder diffraction (XRD).     

Magnetoresistivity and microstructure of YBa2Cu3Oy prepared using planetary ball milling

We have studied the microstructure and the magnetoresistivity of polycrystalline YBa₂Cu₃O_y (YBCO or Y-123 for brevity) embedded with nanoparticles of Y-deficient YBCO, generated by the planetary ball milling technique. Bulk samples were synthesized from a precursor YBCO powder, which was prepared from commercial high purity Y₂O₃, Ba₂CO₃ and CuO via a one-step annealing process in air at 950 °C. After planetary ball milling of the precursor, the powder was uniaxially pressed and subsequently annealed at 950 °C in air. Phase analysis by X-ray diffraction (XRD), granular structure examination by scanning electron microscopy (SEM), microstructure investigation by transmission electron microscopy (TEM) coupled with energy dispersive X-ray spectroscopy (EDXS) were carried out. TEM analyses show that nanoparticles of Y-deficient YBCO, generated by ball milling, are embedded in the superconducting matrix. Electrical resistance as a function of temperature, ρ(T), revealed that the zero resistance temperature, T_co, is 84.5 and 90 K for the milled and unmilled samples respectively. The milled ceramics exhibit a large magnetoresistance in weak magnetic fields at liquid nitrogen temperature. This attractive effect is of high significance as it makes these materials promising candidates for practical application in magnetic field sensor devices.     

Self-assembled 3D La(OH)3 and La2O3 nanostructures: Fast microwave synthesis and characterization

Self-assembled three-dimensional (3D) urchin-like and flower-like La(OH)₃ nanostructures were successfully prepared for the first time via a facile and fast microwave-assisted solution-phase chemical method in 15 min. The obtained products were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). The SEM results reveal that the urchin-like and flower-like La(OH)₃ nanostructures are ca. 3 μm and 6 μm in diameter, respectively. The urchin-like La(OH)₃ nanostructures are constructed by nanorods with diameters of about 300 nm and lengths of about 500 nm. The flower-like La(OH)₃ nanostructures are built from nanopetals about 100 nm thick. The effects of reaction time, microwave power, amount of tetraethyl ammonium bromide (TEAB), and surfactants on the preparation were systematically investigated. The possible formation mechanism of the 3D La(OH)₃ nanostructures was preliminarily discussed. Urchin-like and flower-like La₂O₃ nanostructures were obtained after calcining the La(OH)₃ nanostructures at 800 °C for 4 h. Urchin-like and flower-like La₂O₃:Eu³⁺ nanostructures were also prepared and their photoluminescence (PL) properties were investigated.     

Fabrication and characterization of CuO-core/TiO2-shell one-dimensional nanostructures

We have fabricated CuO-core/TiO₂-shell one-dimensional nanostructures by coating the CuO nanowires with MOCVD-TiO₂. The structure of the core/shell nanowires has been investigated by using scanning electron microscopy, transmission electron microscopy, and X-ray diffraction analysis techniques. The CuO-cores and the TiO₂-shells of the as-synthesized nanowires have been found to have crystalline monoclinic CuO and crystalline tetragonal anatase TiO₂ structures, respectively. The CuO-core/TiO₂-shell nanowires are winding and has rougher surface, whereas the CuO nanowires are straight and have smoother surface.Influence of the substrate temperature and the growth time on the structure such as the morphology, size, and crystallographic orientation of CuO nanowires synthesized by thermal oxidation of Cu foils have also been investigated. All the nanowires have only the CuO phase synthesized at 600 °C, whereas those synthesized at 400 °C have both CuO and Cu₂O phases. The highest density of CuO nanowires with long thin straight morphologies can be obtained at 600 °C. In addition, the growth mechanism of the CuO nanowires has been discussed.     

Synthesis and characterization of nanostructured Li2MnO3 from nanostructured MnOOH precursors

Li₂MnO₃ with different nanostructures was synthesized through a solid-state reaction. MnOOH nanorods and nanowires prepared via the hydrothermal method were used as precursors, respectively, to react with Li(OH)·H₂O to prepare nanostructured Li₂MnO₃ in the temperature range from 500 to 800 °C. The samples were characterized by XRD, TEM, ESR and FTIR results. Based on the experimental results, the dehydration-oxidation-combination (DOC) formation mechanism of Li₂MnO₃ was proposed.     

Field emission from patterned SnO2 nanostructures

A simple and reliable method has been developed for synthesizing finely patterned tin dioxide (SnO₂) nanostructure arrays on silicon substrates. A patterned Au catalyst film was prepared on the silicon wafer by radio frequency (RF) magnetron sputtering and photolithographic patterning processes. The patterned SnO₂ nanostructures arrays, a unit area is of ∼500 μm × 200 μm, were synthesized via vapor phase transport method. The surface morphology and composition of the as-synthesized SnO₂ nanostructures were characterized by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The mechanism of formation of SnO₂ nanostructures was also discussed. The measurement of field emission (FE) revealed that the as-synthesized SnO₂ nanorods, nanowires and nanoparticles arrays have a lower turn-on field of 2.6, 3.2 and 3.9 V/μm, respectively, at the current density of 0.1 μA/cm². This approach must have a wide variety of applications such as fabrications of micro-optical components and micropatterned oxide thin films used in FE-based flat panel displays, sensor arrays and so on.     

Synthesis and CO2 capture property of high aspect-ratio Li2ZrO3 nanotubes arrays

High aspect-ratio Li₂ZrO₃ nanotubes were prepared by hydrothermal method using ZrO₂ nanotubes layers as templates. Characterizations of SEM, XRD, TEM and CO₂ adsorption were performed. The results showed that tetragonal Li₂ZrO₃ nanotubes arrays containing a little monoclinic ZrO₂ can be obtained using this simple method. The mean diameter of the nanotubes is approximately 150 nm and the corresponding specific surface area is 57.9 m² g⁻¹. Moreover, the obtained Li₂ZrO₃ nanotubes were thermally analyzed under a CO₂ flow to evaluate their CO₂ capture property. It was found that the as-prepared Li₂ZrO₃ nanotubes arrays would be an effective acceptor for CO₂ at high temperature.     

Nanoporous ZnO nanostructures for photocatalytic degradation of organic pollutants

ZnO porous bamboo-leave-like nanorods and nanoporous networks were prepared by thermal conversion from Zn₂CO₃(OH)₂?H₂O bamboo-leave-like nanorods, Zn(OH)₂ nanoparticle networks and Zn(OH)₂ long nanostrand networks, respectively. Among them, the ZnO nanoporous networks prepared from Zn(OH)₂ nanostrands had the highest surface area of 78.57 m²/g and presented the best photocatalytic decomposition of organics. The morphologies of the Zn(OH)₂ nanostructures significantly depended on the solvent used for the precursors of aminoethanol and Zn(NO₃)₂ and then determined the corresponding structures and properties of the final ZnO nanostructures. The ethanol/water mixture solvent dramatically increased the stability of Zn(OH)₂ nanostrands. This is very beneficial for the collection and application of Zn(OH)₂ nanostrands.     

Structural and magnetic studies of CuO-TeO2 and CuO-TeO2-B2O3 glasses

The glass systems xCuO ^. (1- x)TeO₂ and xCuO ^. (1- x)[75TeO₂ ^. 25B₂O₃] with 0 < x ? 50 mol% were investigated by means of X-ray diffraction, electron paramagnetic resonance (EPR) and a.c. magnetic susceptibility ( ) measurements, the principal aim of the investigation being the study of the structural modifications in the tellurite glasses introduced by the addition of boron oxide. In the case of first glass system, i.e. without B₂O₃, EPR spectra of Cu²⁺ ions undergo changes with the increasing concentration of CuO. At very low concentrations, spectra are due to isolated Cu²⁺ ions in axially distorted octahedral sites. The EPR signal for samples with 3 ? x ? 20 mol% can be explained as being the superposition of two EPR absorptions, one showing the hyperfine structure typical for isolated Cu²⁺ ions and the other consisting of a symmetric line typical for clustered ions. The broadening of the absorption band is due to dipolar as well exchange interaction. The susceptibility data show that for x > 20 mol%, the Cu²⁺ ions are predominantly clustered and are coupled through antiferromagnetic exchange interaction. A comparative study of amorphous X-ray diffraction pattern of the glasses indicates a structural modification in the TeO₂ network with increasing CuO concentration; the effect is quite visible in the samples with CuO concentrations higher than 20 mole percent. Measurements of density corroborate the conclusions drawn from the X-ray diffraction. Additionally, we show that our data validates a model in which CuO rich regions are surrounded by a buffer boundary which separates them from the tellurite glassy network; effect of introducing B₂O₃ can be best described as breaking these regions into smaller size regions. Received 23 October 2000 and Received in final form 1st February 2001     

Micro-patterns of Au@SiO2 core-shell nanoparticles formed by electrostatic interactions

In this paper, silica-coated Au nanoparticles (Au@SiO₂) were prepared by the technique of vortex mixing. Subsequently, these monodisperse Au@SiO₂ nanoparticles were functionalized by the silane reagents 3-aminopropyltriethoxysilane (APS) and 3-mercaptopropyltriethoxysilane (MPTS) respectively. Then, these NH₂-terminated and SO₃²⁻-terminated Au@SiO₂ nanoparticles were respectively assembled onto the substrates, which have been patterned with different self-assembly monolayers (SAMs), to form close-packed two-dimensional Au@SiO₂ nanoparticle arrays by electrostatic interactions. The morphologies and the optical properties of Au@SiO₂ nanoparticles with different silica-shell thicknesses were characterized by TEM and UV-vis. The compositions and zeta potentials of the functionalized Au@SiO₂ nanoparticles were examined by X-ray photoelectron spectroscopy (XPS) and dynamic light scattering (DLS). The morphologies of the patterns formed on different templates were characterized by atomic force microscopy (AFM).     

Size and Shape Effects of Near-Infrared Light-Activatable Cu2(OH)PO4 Nanostructures on Phototherapeutic Destruction of Drug-Resistant Hypoxia Tumors

Development of simple, robust, and noninvasive therapeutic approaches to treat cancers and improve survival rates is a grand challenge in clinical biomedicine. In particular, the sizes and shape of the nanomaterials play a vital role in dictating their biodistribution and clearance pathways. It remains elusive how the size and shape of a nanomaterial affect its therapeutic efficacy in cancer diagnosis and treatments. To tackle the above problem, the effects of size and shape of Cu₂(OH)PO₄ nanostructures (nanosheets and quantum dots) on the photodynamic therapy (PDT) in destroying malignant drug-resistant lung tumors and on combating the tumor hypoxia problem are investigated and compared. The photocatalytic mechanism of Cu₂(OH)PO₄ nanostructures mainly involves the generation of reactive oxygen species (ROS), such as hydroxyl radical (^·OH) and singlet oxygen (¹O₂). Under an oxygen deprivation condition, Cu₂(OH)PO₄ nanosheets still can generate OH radicals to kill cancer cells upon near-infrared (NIR) light irradiation. Overall, in vitro and in vivo experiments show that Cu₂(OH)PO₄ nanosheets can overcome tumor hypoxia problems and effectively mediate dual modal PDT and photothermal therapeutic (PTT) effects on destruction of NCI-H23 lung tumors in mice using ultralow doses (350 mW cm⁻²) of NIR (915 nm) light.     

Electrostatic assembly of Cu2O nanoparticles on DNA templates

In this paper, a method for highly ordered assembly of cuprous oxide (Cu₂O) nanoparticles (NPs) by DNA templates was reported. Cetyltrimethylammonium bromide (CTAB)-capped Cu₂O NPs were adsorbed onto well-aligned λ-DNA chains to form necklace-like one-dimensional (1D) nanostructures. UV-vis, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) were used to characterize the nanostructure. The Cu₂O nanostructures fabricated with the method are both highly ordered and quite straight.     

Nanocrystalline oxide (Y2O3, Dy2O3, ZrO2, NiO) coatings on BaTiO3 submicron particles by precipitation

Nanocoatings (5–20 nm) of different compounds on fine BaTiO₃ particles were obtained by means of precipitation processes. Homogeneous and smooth shells of Y(OH)CO₃ and Dy(OH)CO₃ were grown from nitrate solutions in the presence of urea. An irregular coating consisting of zirconia nanoparticles was produced from zirconyl nitrate solution using ammonia as a precipitating agent after adsorption of a polymeric polyelectrolyte on the BaTiO₃ surface. Composite particles with a peculiar morphology were obtained by inducing heterogeneous nucleation and growth of Ni(OH)₂ lamellae on the BaTiO₃ surface. The different shells can be transformed in a nanocrystalline coating of the corresponding oxide (Y₂O₃, Dy₂O₃, ZrO₂, NiO) by calcination at moderate temperatures (400–700 °C). The overall results indicate that precipitation from solution represents a versatile process to grow a second-phase layer on the surface of BaTiO₃ particles. This approach can be used as an alternative to mechanical wet mixing for controlled doping of ferroelectric materials and for the fabrication of composite materials with specific geometry of the two-phase assembly.     

Pyridine-thermal synthesis and high catalytic activity of CeO2/CuO/CNT nanocomposites

Carbon nanotubes (CNTs) were controllably coated with the uninterrupted CuO and CeO₂ composite nanoparticles by a facile pyridine-thermal method and the high catalytic performance for CO oxidation was also found. The obtained nanocomposites were characterized by transmission electron microscopy, scanning electron microscopy, X-ray diffraction as well as X-ray photoelectron spectroscopy. It is found that the CuO/CeO₂ composite nanoparticles are distributed uniformly on the surface of CNTs and the shell of CeO₂/CuO/CNT nanocomposites is made of nanoparticles with a diameter of 30-60 nm. The possible formation mechanism is suggest as follows: the surface of CNTs is modified by the pyridine due to the π-π conjugate role so that the alkaline of pyridine attached on the CNT surface is more enhanced as compared to the one in the bulk solvent, and thus, these pyridines accept the proton from the water molecular preferentially, which result in the formation of the OH⁻ ions around the surface of CNTs. Subsequently, the metal ions such as Ce³⁺ and Cu²⁺ in situ react with the OH⁻ ions and the resultant nanoparticles deposit on the surface of CNTs, and finally the CeO₂/CuO/CNT nanocomposites are obtained. The T₅₀ depicting the catalytic activity for CO oxidation over CeO₂/CuO/CNT nanocomposites can reach ∼113 °C, which is much lower than that of CeO₂/CNT or CuO/CNT nanocomposites or CNTs.     

Effect of post heat treatment on microstructure and photocatalytic activities of TiO2 nanoribbons

Low-dimensional TiO₂ nanoribbons were synthesized by a simple one-step hydrothermal method. The TiO₂ nanoribbons were calcined over the temperature range 200-800 °C in order to enhance their photocatalytic properties by altering their crystal phase and increasing crystallization. Effects of hydrothermal temperature, calcinated temperature and calcination time on the formation of nanostructures have been observed and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The (BET) specific surface area of the samples which with different post treatments were determined by N₂ absorption-desorption experiment. In addition, photocatalytic activities of the nanoribbons were evaluated by photodegradation of organic dyes methyl orange under the radiation of UV light. The results reveal that the post-treatments have great effects on the microstructures and the photocatalytic activities of TiO₂ nanoribbons.     

Controlled synthesis of BaWO4 hierarchical nanostructures by exploiting oriented attachment in the solution of H2O and C2H5OH

Shape-controlled synthesis of BaWO₄ hierarchical nanostructures has been successfully achieved by exploiting oriented attachment in a mixture of water and ethanol. A controlled change in the volume ratio of C₂H₅OH and H₂O or the concentration of initial reagents has resulted in the synthesis of products of various morphologies, such as shuttle-like, ellipsoid-like, and flower-like ones. The obtained products are characterized by field emission scanning electron microscopy, high-resolution transmission electron microscopy, X-ray powder diffraction, and Fourier transform infrared spectroscopy. The altered nucleation and growth rates of primary particles that assembled to the final hierarchical nanostructures through oriented attachment are the main cause of the evolution of their morphologies. The room-temperature photoluminescent intensities of the products strongly depend on their morphology.     

La0.67Ca0.33MnO3薄膜皮秒光电效应

在1064 nm波长脉冲激光（脉宽25 ps）的照射下，钙钛矿氧化物薄膜La0.67Ca0.33MnO3/SrTiO3具有超快光电效应，对激光脉冲显示ps量级的响应时间，上升沿响应时间300 ps，半高宽700 ps，同时，对激光能量的响应灵敏度为500 mV/mJ。     

Study on reaction mechanism of YBa2Cu3O7-x film by TFA-MOD process

This paper systematically investigates the intermediate phases of YBa2Cu3O7-x (YBCO) film prepared by metalorganic deposition method using trifluoroacetates (TFA-MOD). According to x-ray diffraction and Raman analyses, the precursor film decomposed in a mixture of BaF2, Y2O3 and CuO after the pyrolysis process. Then these intermediate phases converted into tetragonal YBa2Cu3O6.5 at about 725°C. The influence of water vapour pressure on the YBa2Cu3O7-x film growth on LaAlO3 single-crystal substrates was also studied. The films prepared at low water vapour pressures (40-140 hPa) showed poor electrical performance due to the a-axis grain structure and impurity phases. However, the films prepared at 190 hPa exhibited the highest critical temperature of 90 K and the highest Jc of 3.8 MA/cm2, which was attributed to the formation of a purer YBCO phase and stronger biaxial texture.