Cu在Zr掺杂CeO_2(111)表面吸附特性的第一性原理研究北大核心CSCD

采用第一原理计算方法,计算并分析了Cu在Zr掺杂的CeO2(111)表面吸附的吸附能及所形成的Cu/Ce0.75Zr0.25O2(111)界面体系的吸附结构和电子结构.结果表明:1)Cu在Ce0.75Zr0.25O2(111)表面上邻近Zr原子的次层O的顶位吸附最强;2)Zr的掺杂增强了Cu与CeO2衬底的作用;3)Cu的吸附在Ce0.75Zr0.25O2(111)表面的O2p-Ce4f态之间引入了新的间隙态,这些间隙态主要来自于Cu3d与衬底O2p的杂化作用,这是Cu与Ce0.75Zr0.25O2有较强作用的主要原因;4)吸附的Cu被Ce0.75Zr0.25O2氧化为Cuδ+,并伴随着表面Ce4+→Ce3+的转化,该反应可以总结为:Cu/Ce4+→Cuδ+/Ce3+.     

Au在Zr掺杂的CeO2(110)面吸附的第一性原理研究

采用基于广义梯度近似的投影缀加平面波(projector augmented wave)雁势和具有三维周期性边界条件的超晶胞模型,用第一性原理方法,计算并分析了Au在CeO2(110)和Zr掺杂的CeO2(110) 面的吸附能,吸附结构和电子结构等特征.从而得出Zr掺杂对Au/ CeO2(110)吸附体系的影响.结果表明:Zr的掺杂增大了Au在CeO2(110) 面的吸附能,并改变了最强吸附位置,且导致了吸附体系中衬底结构较大的变化;Zr的掺杂使吸附体系引入了更为复杂的间隙态,使得Zr掺杂的吸附体系有更好的催化活性;Zr的掺杂使吸附原子Au的氧化程度加强,由无掺杂吸附体系中Au得到电子变为Zr掺杂吸附体系中的Au失去电子.以上结果有助于人们更清楚地了解三元催化剂中Zr掺杂的影响以及贵金属Au与CeO2-ZrO2混合氧化物的协同作用机理.     

Cu/CeO2(110)界面特性的第一性原理研究

Cu-CeO₂体系因其特殊的催化能力而在固体氧化物燃料电池和水煤气转化反应等多个催化领域有重要应用. 采用基于密度泛函理论的第一性原理方法, 在原子和电子层面上系统地研究了单个Cu原子及Cu小团簇在CeO₂(110)面上的吸附构型, 价键特性和电子结构, 结果表明: 1) 单个Cu原子的最稳定吸附位是两个表面O的桥位; 2) Cu团簇的稳定吸附构型为扭曲的四面体结构; 3) Cu原子及Cu团簇的吸附在CeO₂(110)面的gap区域引入了间隙态, 这些间隙态主要来自于Cu及其近邻的O和表层还原形成的Ce³⁺, 间隙态的出现表明Cu的吸附增强了CeO₂(110)表面的活性; 4) 吸附的单个Cu原子及Cu团簇分别被CeO₂(110)面表层的Ce⁴⁺离子氧化形成了Cu^δ+和Cu₄^δ+, 并伴随着Ce³⁺离子的形成, 这个反应可归结为Cu_x/Ce⁴⁺→Cu_x^δ+/Ce³⁺; 5) Cu团簇的吸附比Cu单原子的吸附引入了更多的Ce³⁺离子, 进而形成了更多的Cu^δ+-Ce³⁺催化活性中心. 结合已报道的Cu/CeO₂(111)界面特性, 更加全面地探明了Cu与CeO₂(111)和(110)两个较稳定低指数表面的协同作用特性, 较为系统地揭示了Cu增强CeO₂催化特性的原因及Cu与CeO₂协同作用的内在机理. 关键词： 2')" href="#">Cu/CeO₂ U')" href="#">DFT+U 吸附 电子结构     

Pd与CeO2(111)面的相互作用的第一性原理研究

采用基于广义梯度近似的投影缀加平面波(projector augmented wave) 赝势和具有三维周期性边界条件的超晶胞模型,用第一性原理计算方法,计算并分析了Pd在CeO2(111)面上不同覆盖度时的吸附能,价键结构和局域电子结构. 考虑了单层Pd和1/4单层Pd两种覆盖度吸附的情况. 结果表明:1)在单层吸附时,Pd的最佳吸附位置是O的顶位偏向Ce的桥位;在1/4单层吸附时,Pd最易在O的桥位偏向次层O的顶位吸附.2) 单层覆盖度吸附时,吸附原子Pd之间的作用较强;1/4单层覆盖度吸附时,同层吸附的Pd之间的几乎没有相互作用. 同时在低覆盖度吸附时,Pd和CeO2衬底的相互作用较高覆盖度时强.3) Pd的吸附只对其近邻的衬底原子结构有明显影响.4) Pd在CeO2衬底上吸附后,Pd和CeO2衬底的活性增强,并可能在Pd与CeO2界面处形成活性中心. 以上结果有助于人们对三元催化剂中Pd与CeO2的协同作用机理的理解.     

Pt/Ce4O8团簇催化活性的第一性原理研究

基于密度泛函理论的第一性原理计算程序包VASP(Vienna ab-initio Simulation Package), 采用投影缀加平面波(Projector augmented wave, PAW)方法和具有三维周期性边界条件的超原胞模型, 对Pt在Ce4O8团簇上的吸附特性进行了研究. 结果表明Pt在Ce4O8团簇上的吸附作用很强，其吸附能大于Pt在CeO2晶体表面的吸附能. 所得吸附构型可分为三类：单键类, 双键类和多键类. 对其中最稳定吸附构型的电子结构分析表明：Pt的吸附诱导出了间隙态. 该态距离费米能级很近，使Pt/Ce4O8团簇活性很强. Pt与Ce4O8团簇发生了部分电荷转移, 从而使其中的一个Ce4+还原为Ce3+. 这些结果有助于理解在纳米尺度范围内Pt与CeO2的协同作用.     

烧绿石型富氧相Ce_2Zr_2O_8与缺氧相Nd_2Zr_2O_7的振动光谱及XPS对比研究

采用石墨还原法成功制备了富氧相Ce2Zr2O8,选用缺氧相Nd2Zr2O7替代其前驱体CeZrO3.5+δ进行结构对比分析,利用X射线衍射(XRD)、拉曼光谱(Raman)、红外光谱(IR)及X射线光电子能谱(XPS)对样品体、表晶体结构进行表征。XRD结果表明,Ce2Zr2O8相具有典型烧绿石结构特征,表征Ce/Zr阳离子有序排列的超结构峰非常明显,但其Zr—O配位体由前驱体中的[ZrO6]八面体转变为[ZrO8]立方体,[ZrO8]配位体形成大大降低了Ce2Zr2O8的结构稳定性。Raman和IR结果表明,Ce2Zr2O8相的振动光谱谱带比其前驱体替代物Nd2Zr2O7显著增多,说明氧离子的富集导致Ce2Zr2O8相中某些振动简并峰消除简并,该结果进一步证实了其结构对称性较前驱体更低。XPS结果表明,Ce2Zr2O8相表面Ce(Ⅳ)特征峰(916.3eV)非常明显,没有Ce(Ⅲ)特征峰(885eV)出现,说明该相前驱体中的Ce3+已被完全氧化成Ce4+;Ce2Zr2O8相中Zr(3d)结合能与萤石相Gd1.2U0.8Zr2O7+y接近证实其表面形成了与体相一致的[ZrO8]配体;O(1s)低位结合能升高表明Ce2Zr2O8体相氧种介于晶格氧和吸附氧之间,高位氧峰出现说明其表面含有吸附氧,吸附氧与Ce2Zr2O8体相结合强度介于CeO2和Nd2Zr2O7之间。     

CO选择性氧化用Cu_1Zr_1Ce_9O_δ催化剂的红外光谱研究

采用共沉淀法制备了Cu1Zr1Ce9Oδ催化剂,用于富氢气体中CO的选择性氧化反应,利用原位漫反射红外光谱技术考察了Cu1Zr1Ce9Oδ催化剂表面上的吸附物种和反应中间产物。研究发现,H2,O2和CO物种竞争吸附于Cu1Zr1Ce9Oδ表面相同的吸附位上。氢气预处理会引起Cu1Zr1Ce9Oδ催化剂上Cu+物种的深度还原,降低了CO的吸附量。氧气预处理为催化剂提供了较多的活性氧物种,同时抑制了Cu+物种的深度还原。氦气预处理仅起到净化催化剂表面的作用。180℃时Cu1Zr1Ce9Oδ催化剂在2938.7和2843.8cm-1处出现桥式和双齿型甲酸根物种的红外吸收峰。Cu1Zr1Ce9Oδ催化剂上活性较高的氧阴离子在常温下即可将催化剂表面上吸附的CO氧化成表面碳酸根。甲酸根和碳酸根物种占据Cu1Zr1Ce9Oδ催化剂的吸附中心,导致催化剂活性降低。300℃下用氦气吹扫Cu1Zr1Ce9Oδ催化剂表面,双齿型的甲酸根物种分解生成碳酸根物种,碳酸根物种再继续分解生成CO2,释放出催化剂表面的吸附位,恢复了Cu1Zr1Ce9Oδ催化剂的活性。     

Rh在CeO_2(111)表面吸附的第一性原理研究

采用基于广义梯度近似的投影缀加平面波(Projector augmented wave)赝势和具有三维周期性边界条件的超晶胞模型,用第一原理计算方法,计算并分析了Rh在CeO_2(111)表面吸附所形成的Rh/CeO_2(111)界面体系的吸附能,价键结构和局域电子结构.考虑了Rh在不同吸附位置的吸附情况.结果表明:1)Rh在CeO_2(111)面有较大的吸附能,表明Rh与CeO_2(111)面有较强的相互作用,而且Rh在位于表面O的三度位,且位于次层氧的顶位的吸附最强;2)Rh的4d态同衬底O的2p态有明显的杂化作用,这是Rh同CeO_2较强作用的主要原因;3)Rh被CeO_2(主要是Rh的次近邻的Ce)氧化为Rh~(3+),并伴随着Ce~(4+)→Ce~(3+)反应的发生.     

C、N、O掺杂CuBr和CuCl的电子结构和磁性的第一性原理研究

本文基于密度泛函理论(DFT)结合广义梯度近似(GGA),采用第一性原理的平面波赝势方法,探究非磁性sp元素(C、N和O)掺杂卤化物(Cu Cl和Cu Br)是否能诱导产生半金属铁磁性.通过计算体系总能量、能带、态密度和分态密度,分析了非磁性元素掺杂卤化物体系的电子结构和磁性;通过对材料加压,给出了体系铁磁性随压强变化的趋势并作了分析.最后计算显示,O和N掺杂能诱导Cu Cl产生稳定的半金属铁磁性,随着压强的增大Cu Cl0.75N0.25和Cu Cl0.75O0.25的铁磁性减弱最终发生磁相变由铁磁态(FM)转变为非铁磁态(NM).     

SrS:Ce3+薄膜蓝色交流电致发光及其特性的研究

本文采用了SnO2/Y2O3/ZnS/SrS:Ce3+/ZnS/Y2O3/Al这种多层结构制备了SrS:Ce3+薄膜器件,并得到了较亮的蓝色交流电致发光。在5KHz正弦交流电压的激发下,该器件的最大亮度为100cd/m2左右。讨论了衬底温度与薄膜结晶完整性的关系,认为衬底温度在300—400℃之间有利于获得良好的结晶状态。本文还对SrS:Ce3+薄膜的光谱特性进行了讨论,比较了CeF3和CeCl3分别掺杂时,SrS薄膜的发光特性发现CeCl3掺杂较CeF3掺杂好。同时还看到,SrS:Ce3+薄膜的ACEL亮度和效率较ZnS:Ce3+薄膜要高,认为可能的原因是SrS基质提供了一种适合Ce3+激发的环境。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.