Rotation planar extraction and rotation planar chromatography of oak (Quercus robur L.) bark

The versatile novel instrument for rotation planar extraction and rotation planar chromatography was exploited for the investigation of oak bark (Quercus robur L.). The same instrument enabled extraction of the bark, analytical proof of (+)-catechin directly in the crude extract and also its fractionation. Additionally, epimeric flavan-3-ols, (+)-catechin and (-)-epicatechin were separated by analytical ultra-micro rotation planar chromatography on cellulose plates with pure water as developing solvent. A comparison of the extraction of oak bark with 80% aqueous methanol by rotation planar extraction and medium pressure solid-liquid extraction was carried out and both techniques were shown to be suitable for the efficient extraction of oak bark. The raw extracts and fractions on thin-layer chromatography showed many compounds that possessed antioxidant activity after spraying with 1,1-diphenyl-2-picrylhydrazyl. Rotation planar fractionation of 840 mg of crude oak bark extract on silica gel gave 6.7 mg of pure (+)-catechin in one run.     

Effect of the pre-treatment of the samples on the natural substances extraction from Helianthus annuus L. using supercritical carbon dioxide

The extraction of bioactive compounds from sunflowers (Helianthus annuus L.) with supercritical carbon dioxide has been studied. The samples were treated in four different ways and the effects of two factors (pressure and temperature) were investigated at 100, 500 bar and 35, 50 °C. The best yields were obtained using a high temperature and a high pressure (50 °C and 500 bar). The dry samples produced better extraction yields than the moist samples. The bioactivities of the extracts were compared for the samples treated in different ways. The best activity profiles were obtained for the moist samples extracted at 35 °C and 500 bar.     

Determination of catechins and catechin gallates in biological fluids by HPLC with coulometric array detection and solid phase extraction

Tea polyphenols are well known for their beneficial health effects that involve their anti-carcinogenic, anti-mutagenic, anti-pathogenic and anti-oxidative properties. The main polyphenols of green tea are favan-3-ols (catechins) and their corresponding gallate compounds, which constitute about one-third of the dry weight of tea leaves. Their main ingredients are (+)-catechin (C), (−)-epicatechin (EC), (−)-gallocatechin (GC), (−)-epigallocatechin (EGC), (−)-catechin gallate (CG), (−)-epicatechin gallate (ECG), (−)-gallocatechin gallate (GCG) and (−)-epigallocatechin gallate (EGCG). Each has slightly different biological properties. We have developed a method to simultaneously analyze all these compounds in plasma and urine. The samples were first incubated with β-d-glucuronidase and sulfatase to release the catechin residues from their corresponding conjugates for subsequent extraction by selective solid phase column, Waters Oasis HLB extraction cartridges. The extracted molecules were resolved by reversed phase HPLC and monitored by coulometric chemical detection on a CoulArray detector. All eight catechin compounds were analyzed in a single chromatogram within 25 min. For plasma and urine analyses, good linearity (>0.9950) was validated in the range 10-2000 and 10-5000 ng/ml, respectively. The coefficients of variance (CV) were less than 5%. Absolute recovery was greater than 85% and detection limit was 5 ng/ml. The chromatogram exhibited minimal interference as a result of the highly selective solid phase extraction and CoulArray detection.     

Subcritical water extraction of organic matter from sedimentary rocks

Subcritical water extraction of organic matter containing sedimentary rocks at 300 °C and 1500 psi produces extracts comparable to conventional solvent extraction. Subcritical water extraction of previously solvent extracted samples confirms that high molecular weight organic matter (kerogen) degradation is not occurring and that only low molecular weight organic matter (free compounds) are being accessed in analogy to solvent extraction procedures. The sedimentary rocks chosen for extraction span the classic geochemical organic matter types. A type I organic matter-containing sedimentary rock produces n-alkanes and isoprenoidal hydrocarbons at 300 °C and 1500 psi that indicate an algal source for the organic matter. Extraction of a rock containing type II organic matter at the same temperature and pressure produces aliphatic hydrocarbons but also aromatic compounds reflecting the increased contributions from terrestrial organic matter in this sample. A type III organic matter-containing sample produces a range of non-polar and polar compounds including polycyclic aromatic hydrocarbons and oxygenated aromatic compounds at 300 °C and 1500 psi reflecting a dominantly terrestrial origin for the organic materials. Although extraction at 300 °C and 1500 psi produces extracts that are comparable to solvent extraction, lower temperature steps display differences related to organic solubility. The type I organic matter produces no products below 300 °C and 1500 psi, reflecting its dominantly aliphatic character, while type II and type III organic matter contribute some polar components to the lower temperature steps, reflecting the chemical heterogeneity of their organic inventory. The separation of polar and non-polar organic compounds by using different temperatures provides the potential for selective extraction that may obviate the need for subsequent preparative chromatography steps. Our results indicate that subcritical water extraction can act as a suitable replacement for conventional solvent extraction of sedimentary rocks, but can also be used for any organic matter containing mineral matrix, including soils and recent sediments, and has the added benefit of tailored extraction for analytes of specific polarities.     

The extraction and speciation of arsenic in rice flour by HPLC-ICP-MS

Several solvent mixtures and techniques for the extraction of arsenic (As) species from rice flour samples prior to their analysis by HPLC-ICP-MS were investigated. Microwave-assisted extraction using water at 80 °C for 30 min provided the highest extraction efficiency. Total recoveries of extracted As species were in good agreement with the total As concentrations determined by ICP-MS after microwave-assisted acid digestion of the samples. Arsenite [As(III)], arsenate [As(V)] and dimethylarsinic acid (DMAA) were the main species detected in rice flour samples.     

Pressurized liquid extraction followed by gas chromatography with atomic emission detection for the determination of fenbutatin oxide in soil samples

A novel method for the determination of the miticide bis[tris(2-methyl-2-phenylpropyl)tin] oxide, also known as fenbutatin oxide (FBTO), in agricultural soils is presented. Pressurized liquid extraction (PLE) followed by analyte derivatization and extraction into isooctane was the used sample preparation approach. Selective determination was achieved by gas chromatography with atomic emission detection (GC-AED). Influence of different parameters on the performance of the extraction process is thoroughly discussed; moreover, some relevant aspects related to derivatization, determination and quantification steps are also presented. As regards PLE, the type of solvent and the temperature were the most relevant variables. Under optimized conditions, acetone, without any acidic modifier, was employed as extractant at 80 °C. Cells were pressurized at 1500 psi, and 2 static cycles of 1 min each were applied. Acetone extracts (ca. 25 mL) were concentrated to 1 mL, derivatized with sodium tetraethyl borate (NaBEt₄) and the FBTO derivative, resulting from cleavage of the Sn-O-Sn bond followed by ethylation of the hydroxyl fragments, extracted into isooctane and determined by GC-AED. Under final working conditions, the proposed method provided recoveries from 76 to 99% for spiked soil samples, a limit of quantification of 2 ng g⁻¹ and an acceptable precision. Analysis of samples from vineyards sprayed with FBTO, confirmed the persistence of the miticide in soil for more than 1 year after being applied.     

Densitometric determination of (+)-catechin and (−)-epicatechin by 4-dimethylaminocinnamaldehyde reagent

We report the optimization of a sensitive, selective and robust derivatization method using 4-dimethylaminocinnamaldehyde (DMACA) for densitometric determination of (+)-catechin and (−)-epicatechin. The separation of these compounds was achieved by thin-layer chromatography (TLC) on cellulose plates developed with water. With DMACA in HCl, both compounds gave blue bands, while under the same conditions, vanillin produced a fast fading red coloration of bands. Quantitation at 655 nm showed that for both compounds the calibration curve was linear from 2 to 12 ng and polynomial from 2 to 30 ng, and the repeatability of chromatography of 20 ng was 3.5% (RSD, n = 6). The visible limit of detection of both standards was 1 ng, but the densitometric limit of detection was lower (0.2 ng). The optimized DMACA reagent is superior to the more frequently used vanillin reagent and is applicable also for determination of mixtures containing other catechins ((−)-catechin, (−)-epicatechin gallate, (−)-epigallocatechin gallate, procyanidin A2, procyanidin B1 and procyanidin B2).     

Pressurized liquid extraction of isoflavones from soybeans

Isoflavone derivatives from freeze-dried soybeans were extracted by pressurized liquid extraction (PLE) and determined by reverse-phase high performance liquid chromatography (HPLC) with both photo diode array and mass spectrometry (MS) detection. Both real and spiked samples were used in the development of the method.Several extraction solvents (methanol (MeOH) and ethanol (EtOH), 30-80% in water and water), temperatures (60-200 °C), pressures (100-200 atm), as well as the sample size (0.5-0.05 g) and cycle length (5-10 min) were studied for the optimization of the extraction protocol. The optimized extraction conditions for quantitative recoveries were: 0.1 g of sample, 100 °C, three (7 min) static extraction cycles and ethanol 70% as extracting solvent. The stability of the isoflavones during the PLE was also determined. Under PLE conditions, degradation of malonyl glucoside forms of the isoflavones takes place using temperatures higher than 100 °C whereas degradation of glucosides takes place above 150 °C. Using the optimized protocol, isoflavones can be extracted from freeze-dried soybeans without degradation.     

Pressurized liquid extraction and anticholinesterase activity-based thin-layer chromatography with bioautography of Amaryllidaceae alkaloids

Modern extraction technique-pressurized liquid extraction (PLE) was optimised for extraction of lycorine and galanthamine (Amaryllidaceae alkaloids) from Narcissus jonquilla ‘Pipit’. Crude extracts were purified on Oasis MCX cartridges, and the alkaloids eluted with 80-100% recoveries using methanol-10% ammonia solution (3:1, v/v). Quantitative results were obtained by both HPTLC-densitometry on silica gel plates and RP-HPLC with diode array (DAD) on XTerra C₁₈ stationary phase. Both methods were fully validated in terms of specificity, precision (including intra- and inter-day measurements), LOD and LOQ values, correlation of UV spectra and linearity of calibration curves. The methods were also well correlated each other with correlation coefficients (r) 0.98823 and 0.99081, respectively, for the mean values of galanthamine and lycorine.Among the investigated solvents methanol and 1% tartaric acid methanolic solution at default conditions (120 °C, p = 60 bar, time: 10 min, one static cycle) permit the highest yields of the total sum of the alkaloids, whereas for toluene the lowest amounts were measured. Lycorine to galanthamine mean ratios were dependant on the type of solvent used, and in toluene galanthamine and related alkaloids were preferably extracted.In temperature experiments for galanthamine, the levels of this compound increased from the temperature of 20 till 150 °C in the investigated solvent systems, then decreased with slight increase from the temperature of 175 to 200 °C in 1% tartaric acid methanolic solution. When lycorine was analysed, similar trends were observed, however the maximum of the concentration was measured at a temperature about 125 °C. The ratios of the mean values of these two compounds differed in temperature-dependant experiments in both solvent systems.Further more, two TLC with bioautography approaches were used in screening for anticholinesterese properties of the extracts. No qualitative differences were found among the different solvent extracts, and AChE inhibition was correlated with galanthamine and related compounds.In conclusion, optimised PLE was much more effective than previously applied hot-solvent extraction, microwave-assisted extraction (MAE) or ultrasound-assisted extraction (USAE).     

Solid phase microextraction using new sol–gel hybrid polydimethylsiloxane-2-hydroxymethyl-18-crown-6-coated fiber for determination of organophosphorous pesticides

A new sol–gel hybrid coating, polydimethylsiloxane–2-hydroxymethyl-18-crown-6 (PDMS–2OHMe18C6) was prepared in-house for use in solid phase microextraction (SPME). The three compositions produced were assessed for its extraction efficiency towards three selected organophosphorus pesticides (OPPs) based on peak area extracted obtained from gas chromatography with electron capture detection. All three compositions showed superior extraction efficiencies compared to commercial 100 μm PDMS fiber. The composition showing best extraction performance was used to obtain optimized SPME conditions: 75 °C extraction temperature, 10 min extraction time, 120 rpm stirring rate, desorption time 5 min, desorption temperature 250 °C and 1.5% (w/v) of NaCl salt addition. The method detection limits (S/N = 3) of the OPPs with the new sol–gel hybrid material ranged from 4.5 to 4.8 ng g⁻¹, which is well below the maximum residue limit set by Codex Alimentarius Commission and European Commission. Percentage recovery of OPPs from strawberry, green apple and grape samples with the new hybrid sol–gel SPME material ranged from 65 to 125% with good precision of the method (%RSD) ranging from 0.3 to 7.4%.     

Extraction of fatty acids from grape seed by superheated hexane

Superheated hexane extraction has been tested for obtaining fatty acids from grape seed and compared with conventional Soxhlet and hot hexane extractions. Seeds from grape residues from a winery were dried for 46 h at 105 °C, milled and sieved by particle size (d < 0.42 mm, 0.42 < d < 0.84 mm and d > 0.84 mm). An optimization study of influential variables on superheated hexane extraction (namely extraction time, temperature, pression, particle size and sample amount) was carried out by a multivariate approach. All the extracts were concentrated in a rotary evaporator and dried by adding 1 g of Na₂SO₄. Then, 2 ml of the dried extract were subjected to reaction with 1 ml of a 0.5 M solution of sodium methylate in methanol to obtain fatty acid methyl esters (FAMEs). After derivatization, FAMEs were quantified by GC-FID. The results show that the optimal conditions for superheated hexane extraction are: time extraction, 10 min; temperature, 80 °C; pressure, 40 bar; particle size, d < 0.42 mm; amount of sample, 0.4 g. Under these conditions, around 84% of the fatty acids (out of the amount obtained by Soxhlet extraction) is extracted. Comparison with Soxhlet and hot hexane extractions showed that the percentages of FAMEs are similar in all the extracts and they agree with the data in the bibliography.     

Extraction and analysis of trace amounts of cyclonite (RDX) and its nitroso-metabolites in animal liver tissue using gas chromatography with electron capture detection (GC-ECD)

An efficient extraction and cleanup technique, and an instrumental detection method suitable for determination of trace amounts of hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) and its nitroso-metabolites in animal liver tissue were developed and validated in this paper. The method includes the extraction of explosives from liver tissue samples using accelerated solvent extraction (ASE) followed by cleanup using florisil and styrene-divinyl benzene (SDB) cartridges to remove interfering naturally endogenous compounds. The instrumental analysis was conducted using a capillary column gas chromatograph coupled with an electron capture detector (GC-ECD). High recoveries (58.9-106.8%) of RDX, hexahydro-1-nitroso-3,5-dinitro-1,3,5-triazine (MNX), hexahydro-1,3-dinitroso-5-nitro-1,3,5-triazine (DNX), and hexahydro-1,3,5-trinitroso-1,3,5-triazine (TNX) were achieved at all concentrations studied. RDX, MNX, and TNX gave higher recoveries than DNX at all three tested concentrations (50, 250, 1250 ng/g). Overall recoveries of RDX, MNX, DNX, and TNX from 1 g beef liver samples containing 50, 250, and 1250 ng/g were 80.1, 82.8, 68.9, and 80.4%, respectively. The optimal injection port temperature range was 160-170 °C for analysis of RDX and its nitroso-metabolites. Higher or lower temperatures than 160-170 °C decreased signal amplitudes. RDX was unstable in the liver extraction matrix; as much as 50% of RDX was degraded 10 days after extraction if keeping the liver sample extracts at room temperature. Degradation of RDX to MNX, DNX, or TNX was not detected during the sample storage, extraction, or instrument analysis processes. Other optimized extraction and GC conditions are also discussed.     

Long-term performance of poly(vinyl chloride) cables, Part 2: Migration of plasticizer

Cable samples with plasticized poly(vinyl chloride) insulations were aged in air at temperatures between 80 and 155 °C. The concentrations of the plasticizer (di-(2-ethylhexyl) phthalate, DEHP) in the insulations of the aged cables were determined by extraction of samples in tetrahydrofuran followed by analysis of the extract by liquid chromatography. The plasticizer concentration data for different ageing times were analysed by numerical methods, fitting Fick's second law with a concentration-dependent diffusivity. The analysis showed that the transport of the plasticizer to the surrounding air phase was controlled by diffusion at 120 and 155 °C with an activation energy of 89 kJ mol⁻¹. The evaporation of the plasticizer from the outer boundary was rate controlling at lower temperatures (≤100 °C). The rate of evaporation was initially constant and independent of the plasticizer concentration at both 80 and 100 °C. The activation energy for the initial DEHP loss rate from PVC at these temperatures was the same as that obtained for evaporation of pure DEHP on a glass plate at 60-100 °C measured by thermogravimetry, 98 ± 2 kJ mol⁻¹. Furthermore, the evaporation rate of pure DEHP on a glass plate was also of the same order of magnitude as the rate of plasticizer loss from the cable insulation. Extrapolation of the plasticizer loss rate data (from the cable at 80 °C and from pure liquid DEHP at temperatures between 60 and 100 °C) to 25 °C predicted a maximum loss of plasticizer of 1% over 25 years. This is in accordance with earlier presented data and with the data presented in this report.     

Speciation analysis of antimony in marine biota by HPLC-(UV)-HG-AFS: Extraction procedures and stability of antimony species

Speciation analysis of antimony in marine biota is not well documented, and no specific extraction procedure of antimony species from algae and mollusk samples can be found in the literature. This work presents a suitable methodology for the speciation of antimony in marine biota (algae and mollusk samples). The extraction efficiency of total antimony and the stability of Sb(III), Sb(V) and trimethylantimony(V) in different extraction media (water at 25 and 90 °C, methanol, EDTA and citric acid) were evaluated by analyzing the algae Macrosystis integrifolia (0.55 ± 0.04 μg Sb g⁻¹) and the mollusk Mytilus edulis (0.23 ± 0.01 μg Sb g⁻¹). The speciation analysis was performed by anion exchange liquid chromatography (post-column photo-oxidation) and hydride generation atomic fluorescence spectrometry as detection system (HPLC-(UV)-HG-AFS). Results demonstrated that, based on the extraction yield and the stability, EDTA proved to be the best extracting solution for the speciation analysis of antimony in these matrices. The selected procedure was applied to antimony speciation in different algae samples collected from the Chilean coast. Only the inorganic Sb(V) and Sb(III) species were detected in the extracts. In all analyzed algae the sum of total antimony extracted (determined in the extracts after digestion) and the antimony present in the residue was in good agreement with the total antimony concentration determined by HG-AFS. However, in some extracts the sum of antimony species detected was lower than the total extracted, revealing the presence of unknown antimony species, possibly retained on the column or not detected by HPLC-(UV)-HG-AFS. Further work must be carried out to elucidate the identity of these unknown species of antimony.     

Antioxidant activity of grape skin aqueous extracts from pressurized hot water extraction combined with electron paramagnetic resonance spectroscopy

Pressurized hot water extraction (PHWE) was employed to prepare extracts from dried grape skin of two wine grape varieties (St. Laurent and Alibernet) at various temperatures (from 40 up to 120 °C) and amounts of sample (0.5, 1.0 and 1.5 g). To assess the antioxidant activity of the extracts, electron paramagnetic resonance (EPR) spectroscopy was applied involving DPPH and ABTS⁺ assays. Other extract characteristics including HPLC profile of anthocyanins and total phenolic compound content were obtained as well. PHWE has also been compared with earlier results of extractions of the same grape skin samples with compressed methanol and compressed ethanol under the conditions of pressurized fluid extraction (PFE). From this comparison, PHWE emerges as the more benign and efficient extraction method to recover valuable phenolic antioxidants from grape skins for the prospective use in functional food supplements.     

Importance of control of enzymatic degradation for determination of bisphenol A from fruits and vegetables

The purpose of this study was to develop an analytical method for determination of bisphenol A (BPA) from fruits and vegetables. The present method developed for extraction of BPA from samples was based on solid-phase extraction (SPE) method and solvent extraction. Recovery results in the samples spiked with a 10 ng/ml BPA [no detection (<1 ng/g) to 77%] were lower than those in the samples with a 50 ng/ml BPA (26-96%). The fact that the low recovery results were caused by BPA degradation by enzymes is found. These problems were proved by the pH (pH ≤3) and the heating treatment (at ≥80 °C for 5 min). However, because the heating treatment at temperatures of ≥80 °C for 5 min is more difficult and time-consuming method than the pH control, we suggest that the pH control is useful to prevent BPA degradation. Good recovery results (82-101%) were obtained from all fruit and vegetable samples after pH treatment (pH ≤3). Effective elimination of impurities and a good detection limit (1 ng/g) were obtained with a method involving two SPE cartridges (OASIS HLB and Sep-Pak Florisil cartridge).     

Effect of surface fluorination on the electrochemical behavior of petroleum cokes for lithium ion battery

Surface structure change and electrochemical behavior of fluorinated petroleum coke samples (petroleum cokes: petroleum coke and those heat-treated at 1860 °C, 2300 °C and 2800 °C, abbreviated to PC, PC1860, PC2300 and PC2800, respectively) have been investigated. Surface oxygen of petroleum coke was decreased by the fluorination using elemental fluorine. Raman and EPR spectroscopies revealed that surface fluorination increased surface disorder and lattice defects. ¹⁹F NMR spectrum suggests that distribution of fluorine atoms in PC fluorinated 300 °C was similar to that in graphite fluoride with covalent CF bonds. Surface areas of fluorinated petroleum cokes were nearly the same as those of non-fluorinated ones or only slightly increased by fluorination, except PC fluorinated at 300 °C. It is noted that first coulombic efficiencies of PC2300 and PC2800 were highly increased to 80-84% by the fluorination at 300 °C. These values of 80-84% were 12-18% higher than those of non-fluorinated PC2300 and PC2800.     

Investigation on Ochratoxin A stability using different extraction techniques

The stability of Ochratoxin A during its extraction using different extraction techniques has been evaluated. Microwave-assisted extraction and pressurised liquid extraction, in addition to two other reference methods of extraction, i.e. ultrasound-assisted and magnetic stirring-assisted extraction, were evaluated. The effect of extraction temperature using the cited techniques was checked.The results show that Ochratoxin A can be extracted using microwave-assisted extraction at temperatures up to 150 °C without degradation. Pressurised liquid extraction can be used at temperatures up to 100 °C, for extraction times of less than 30 min. Further, both ultrasound-assisted extraction and magnetic stirring extraction can be applied at temperatures up to 65 °C.High-performance liquid chromatography combined with fluorescence detection using a Chromolith RP-18e column at a flow rate of 5 mL min⁻¹ was used to quantify the Ochratoxin A. The retention time for the Ochratoxin A was 1.3 min. The limits of detection (LOD) and of quantification (LOQ) were 0.03 and 0.10 μg L⁻¹, respectively.     

Determination of water soluble trace metals in airborne particulate matter using a dynamic extraction procedure with on-line inductively coupled plasma optical emission spectrometric detection

A novel continuous-flow system for the dynamic extraction of water soluble metal fractions in airborne particulate matter (APM) with subsequent inductively coupled plasma optical emission spectrometric (ICP-OES) analysis of derived extracts is presented. The fully automated extraction system with on-line multi-element detection offers enhanced sensitivity when compared to batch-wise counterparts; additionally it provides information about the extraction process. With the developed procedure detection limits in the order of 1.5 (Ba) to 8.0 (Ni) ng extractable mass per investigated sample could be achieved, which translates to method detection limits for soluble metal concentrations in APM ranging from 0.2 ng m⁻³ (Ba) to 0.9 ng m⁻³ (Fe). Reproducibility of analysis was determined by replicate measurement (n = 6) of an APM sample with an aerodynamic diameter ≤10 μm (PM10), derived results varied between 3.5% (Mn) and 12.1% (Ni) relative standard deviation. Method validation was accomplished by comparison of extracted soluble and remaining non-soluble fractions with the total metal contents of the investigated PM10 samples, showing an excellent mass balance for all elements. Application of the developed procedure for the analysis of water soluble metal fractions in PM10 samples (n = 16) from Linz (Austria) indicated a high variability of extractable fractions ranging from 11.7 ± 7.2% (Fe) to 48.8 ± 15.4% (Mn) of the total metal contents.     

Validated hydrophilic interaction LC-MS/MS method for simultaneous quantification of dacarbazine and 5-amino-4-imidazole-carboxamide in human plasma

A hydrophilic interaction high performance liquid chromatography-tandem mass spectrometric method has been developed and validated for simultaneous quantification of dacarbazine (DTIC) and its terminal metabolite, 5-amino-4-imidazole-carboxamide (AIC) in human plasma. The plasma samples are first extracted by a C8 + SCX mixed-mode 96-well plate to extend the extraction stability of DTIC and AIC. The extracted residues are further cleaned by a primary and secondary amine (PSA) adsorbent for minimization of matrix effect. Analyses are done on an Amide-80 HPLC column coupled to a tandem mass spectrometer fitted with an atmospheric pressure turbo ion spray ionization interface in the positive-ion mode. Both DTIC and AIC have reproducible retention times on the Amide-80 HPLC column. This type of column not only has an excellent column life (over 4000 injections), but also has zero carryover effect. The injection volume should be limited at 10 μL or less to avoid the peak splitting. The validated concentration ranges are from 0.5 to 500 ng/mL for DTIC and from 2.0 to 500 ng/mL for AIC. The validated method has been successfully applied to determine the pharmacokinetic profiles for human patients receiving DTIC infusions.