Preparation,structure, and property of polyoxymethylene/carbon nanotubes thermal conducive composites

Polyoxymethylene (POM)/multiwalled carbon nanotubes (MWNTs) nanocomposites were prepared through a simple solution‐evaporation method assisted by ultrasonic irradiation. To enhance the dispersion of MWNTs in POM, MWNTs were chemically functionalized with PEG‐substituted amine (MWNT‐g‐PEG), which exhibited strong affinity with POM due to their similar molecular structure. The thermal conductivity and the mechanical properties of the composites were investigated, which showed that the thermal conductive properties of POM were improved remarkably in the presence of MWNTs, whereas reduced by using MWNT‐g‐PEG due to the heat transport barrier of the grafted‐PEG‐substituted amine chain. A nonlinear increase of the thermal conductivity was observed with increasing MWNTs content, and the Maxwell‐Eucken model and the Agari model were used for theoretical evaluation. The relatively high effective length factor of the composite predicted with mixture equation indicated that there were few entangles of MWNTs for the samples of MWNT‐g‐PEG in the composites. The mechanical strength of the composites can be improved remarkably by using suitable content of such functionalized MWNTs, and with the increase of the aliphatic chain length of PEG‐substituted amine, the toughness of the composites can be enhanced. Transmission electron microscope result indicated that MWNT‐g‐PEG exhibited strong affinity with POM and a good dispersion of MWNTs was achieved in POM matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 905–912, 2010     

Enhancement in solubility and conductivity of polyaniline with lignosulfonate modified carbon nanotube

An organic solvent soluble and high electrical conductivity, for example, 55.43 S/cm, polyaniline (PANI), was synthesized by a novel method. In this two steps process, a noncovalent approach was initially developed by functionalization of multiwalled carbon nanotubes (MWNTs) using calcium lignosulfonate (LsCa) via self‐assembly to result MWNTs‐LsCa. Then, the MWNT‐LsCa was employed as a template to lead anilinium monomers directly aligned on the surface to start the polymerization of PANI. The noncovalent modification of MWNTs avoided their agglomeration effectively to allow them doped in PANI at the molecular level. The obtained novel PANI/MWNTs‐LsCa presented excellent solubility and high conductivity. The recorded scanning electron microscopy photographs revealed that the MWNTs‐LsCa was wrapped with PANI chains that caused the crystal orientation improvement. In this article, a related scheme on resulting in the high conductivity of PANI/MWNTs‐LsCa was showed and described. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2036–2046, 2009     

聚3-辛基噻吩/MWNTs复合材料的导电性能研究

采用在氯仿溶液中超声共混, 制备聚3-辛基噻吩(P3OT)和多壁碳纳米管(MWNTs)复合材料. 当MWNTs掺杂量为3%时复合材料的电导率为1.43 S•m－1, 达到纯MWNTs的电导率水平. 用FTIR光谱, TG, UV-Vis光谱, XPS和FESEM进行研究分析, 认为MWNTs的离域电子与P3OT主链上的π电子之间形成π-π共轭, 增加了P3OT主链的有效共轭度, 被掺杂的P3OT具有很高的电导率, 提高了复合材料的导电性能. MWNTs与被掺杂的P3OT组成相对独立的导体单元, 对复合材料的导电网络形成起着主要作用.     

Bulk polymerized polystyrene in the presence of multiwalled carbon nanotubes

The in situ bulk polymerization method was applied to synthesize composites of multiwalled carbon nanotubes (MWNTs) and polystyrene (PS) under ultrasonication to open π-bonds in the MWNTs. Morphology of the composite products was studied by both scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Thermal properties and molecular weight of the PS synthesized in the presence of the MWNTs were examined by thermogravimetric analysis (TGA) and gel permeation chromatography (GPC), respectively. The MWNTs were observed to play an important role as initiator consumers during the polymerization reaction. Electrical conductivity of a film-type sample of the PS/MWNT nanocomposite was found to increase with increased amount of MWNTs added, following the percolation theory.     

Changes During Storage of Electrically Conductive Blends Polyaniline–Poly(Ethylene‐co‐vinyl Acetate)

Abstract

The electrical conductivity behavior of polyaniline–poly(ethylene‐co‐vinyl acetate) (PANI–EVA) blends was variable and dynamic during their storage. It was shown that the apparent concentration of the intrinsically conductive polymer at which a conductivity jump of the blends occurs (Φ _c ) is not a constant value over time. The electrical conductivity of the films of low PANI content (below 2.5 wt.%) increased by several (ca. 5) orders of magnitude. It was found that the PANI phase undergoes a flocculation process subsequently resulting in the formation of conductive pathways and a continuous network. Besides, the shape of percolation curves was found to change during storage of the films. Decreased conductivity deviations were registered for blends of low PANI content (<2.5 wt.%), indicating that an improvement (or decreasing number of defects) of the conductive pathways took place within the bulk of the insulating EVA matrix. These results and observed phenomena are discussed by means of the interfacial model for electrically conductive polymer blends. They supported the dispersion/flocculation phase transition within similar composite materials. The phase separation and conductivity jump are attributed to the interfacial interactions between the polymeric constituents. It was shown that the microstructure of the blends consists of highly ordered PANI paths embedded in the insulating EVA matrix. Long fibrils of PANI and interconnected fractal‐like networks were observed. It was found that the sizes of the PANI domains also varied during storage of the films. Due to the spontaneous flocculation of the primary PANI particles, conductive pathways are formed at extremely low percolation threshold (Φ _c , loading level ca. 5 × 10^?3 wt. fraction). Thus, an important property of the conductive constituent, namely its solid‐state rearrangement, was proved. This PANI self‐organization is also interpreted according to the interfacial model of polymer composites. On the other hand, the competition between self‐organization of the complex of PANI with dodecylbenzenesulfonic acid and crystallization of EVA matrix has resulted in structural changes and formation of continuous conductive networks within the blends, responsible for their significantly increased conductivity.     

Grafting of polyaniline onto the surface of 4‐aminobenzoyl‐functionalized multiwalled carbon nanotube and its electrochemical properties

Polyaniline (PANi)‐grafted multiwalled carbon nanotube (MWNT) composite is prepared by a two‐step reaction sequence. MWNT is first functionalized with 4‐aminobenzoic acid in polyphosphoric acid/phosphorous pentoxide as a “direct” Friedel‐Crafts acylation reaction medium. The resultant 4‐aminobenzoyl‐functionalized MWNT is then treated with aniline using ammonium persulfate/aqueous hydrochloric acid to promote a chemical oxidative polymerization, leading to PANi‐grafted MWNT composite. The resultant composite is characterized by elemental analysis, Fourier‐transform infrared spectroscopy, wide‐angle X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, UV–vis absorption spectroscopy, fluorescence spectroscopy, cyclic voltammetry, and electrical conductivity measurement. The thermooxidative stability and electrical conductivity of PANi‐grafted MWNT composite are improved compared to those of PANi. Specifically, the electrical conductivity of PANi‐grafted MWNT is improved 10–900 times depending upon the level of doping. The capacitance of the composite is also greatly enhanced. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3103–3112, 2010     

磺化聚苯乙炔/多壁碳纳米管复合材料导电机理研究

将磺化聚苯乙炔(SPPA)与多壁碳纳米管(MWNT)超声共混制备得到SPPA/MWNT复合材料. 用四探针电阻率测试、场发射扫描电镜(FESEM)、XPS、UV-Vis、XRD等方法对复合材料导电机理进行研究. 结果表明, SPPA/MWNT的电导率发生两次突跃；掺杂剂MWNT具有低的临界阈值; 临界阈值附近, 复合材料中MWNT具有不连续分布的现象及复合材料电阻呈负温度系数(NTC)效应; SPPA/MWNT复合材料中MWNT的碳原子对SPPA 进行掺杂. 推测复合材料的导电机理为, 共轭聚合物SPPA不仅被导电粒子MWNT物理填充, 同时还被MWNT的碳原子掺杂, 使复合材料中存在两种导电通路而导电, 一是因被掺杂而成为高电导率主体的SPPA相互接触形成的导电通路, 二是MWNT相互接触形成的导电通路.     

Nylon 610/functionalized multiwalled carbon nanotube composite prepared from in‐situ interfacial polymerization

Pristine multiwalled carbon nanotubes (P‐MWNTs) were functionalized with 4‐chlorobenzoic acid via “direct” Friedel‐Crafts acylation in polyphosphoric acid (PPA)/phosphorous pentoxide (P₂O₅) medium. The resultant 4‐chlorobenzoyl‐functionalized MWNTs (F‐MWNTs) were soluble in chlorinated solvents such as dichloromethane, chloroform, and carbon tetrachloride. A large scale of nylon 610/F‐MWNT composite could be conveniently prepared by in situ interfacial polymerization of 1, 6‐hexamethylenediamine (HMDA) in an aqueous phase, and sebacoyl chloride with F‐MWNTs in an organic phase. Similarly, nylon 610/P‐MWNT composite was also prepared for comparison. The state of F‐MWNTs dispersion in nylon 610 matrix was distinctively better than that of P‐MWNTs, which could be clearly discerned by both naked eye and scanning electron microcopy (SEM). As a result, the tensile strength of nylon 610/F‐MWNT composite was 4.9‐fold higher than that of nylon 610/P‐MWNT composite. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6041–6050, 2008     

Thermal stability and glass transition behavior of PANI/MWNT composites

Polyaniline/multi-walled carbon nanotube (PANI/MWNT) composites were prepared by in situ polymerization. Transmission electron microscope (TEM), X-ray diffraction (XRD) and Fourier transform infrared (FTIR) were used to characterize the PANI/MWNT composites. Thermal stability and glass transition temperature (T _g) were measured by thermogravimetry (TG) and temperature modulated differential scanning calorimetry (TMDSC), respectively. The TG and derivative thermogravimetry (DTG) curves indicated that with augment of MWNTs content, the thermal stability of PANI/MWNT composites increased continuously. While, T _g increased and then decreased with the MWNTs content increasing from 0 to 20 mass%.     

A novel approach for preparation of conductive hybrid elastomeric nano‐composites

Since the discovery of carbon nanotubes (CNTs) and intrinsically conductive polymers, such as polyaniline (PANI) some research has focused on the development of novel hybrid materials by combining CNT and PANI to achieve their complementary properties. Electrically conductive elastomer nano‐composites containing CNT and PANI are described in the present investigation. The synthesis procedure includes in‐situ inverse emulsion polymerization of aniline doped with dodecylbenzene sulfonic acid in the presence of CNT and dissolved styrene‐isoprene‐styrene (SIS) block copolymer, followed by a precipitation–filtration step. The synthesis step is carried out under ultrasonication. The resulting uniform SIS/CNT/PANI dispersions are stable for long time durations. The incorporation of CNT/PANI in the SIS elastomeric matrix improves thermal, mechanical and electrical properties of the nano‐composites. The formation of continuous three‐dimensional CNT/PANI network, assumed to be responsible for enhancement of the resulting nano‐composite properties, is observed by HRSEM. A relatively low percolation threshold of 0.4 wt.% CNT was determined. The Young's modulus of the SIS/CNT/PANI significantly increases in the presence of CNT. High electrical conductivity levels were obtained in the ternary component systems. Copyright © 2013 John Wiley & Sons, Ltd.     

Electrocatalytic Dioxygen Reduction at Glassy Carbon Electrode Modified with Polyaniline Grafted Multiwall Carbon Nanotube Film

The work details the electrocatalysis of oxygen reduction reaction (ORR) in 0.5 M H₂SO₄ medium on a modified electrode containing a film of polyaniline (PANI) grafted multi‐wall carbon nanotube (MWNT) over the surface of glassy carbon electrode. We have fabricated a novel modified electrode in which conducting polymer is present as connected unit to MWNT. The GC/PANI‐g‐MWNT modified electrode (ME) is fabricated by electrochemical polymerization of a mixture of amine functionalized MWNT and aniline with GC as working electrode. Cyclic voltammetry and amperometry are used to demonstrate the electrocatalytic activity of the GC/PANI‐g‐MWNT‐ME. The GC/PANI‐g‐MWNT‐ME exhibits remarkable electrocatalytic activity for ORR. A more positive onset potential and higher catalytic current for ORR are striking features of GC/PANI‐g‐MWNT‐ME. Rapid and high sensitivity of GC/PANI‐g‐MWNT‐ME to ORR are evident from the higher rate constant (7.92×10² M^?1 s^?1) value for the reduction process. Double potential chronoamperometry and rotating disk and rotating ring‐disk electrode (RRDE) experiments are employed to investigate the kinetic parameters of ORR at this electrode. Results from RDE and RRDE voltammetry demonstrate the involvement of two electron transfer in oxygen reduction to form hydrogen peroxide in acidic media.     

多壁碳纳米管/聚乙烯复合材料的制备及其导电行为

多壁碳纳米管/聚乙烯复合材料的制备及其导电行为;碳纳米管;高密度聚乙烯;渗流阈值;导电行为;V-PTC特性     

Dramatic enhancement of carbon nanotube dispersion in polyimide composites by a two‐step amino functionalization approach

Amino modified multiwall carbon nanotubes (MWNTs) are prepared, respectively, by two ways: the conventional one‐step method that directly treats acyl chloride functionalized MWNTs with 4, 4′‐diaminodiphenyl ether (ODA), giving the amino modified MWNT (Di‐MWNT), as well as an improved two‐step method in which acyl chloride functionalized MWNT react with mono‐Boc protected ODA first and then the Boc‐groups are deprotected to provide the amino modified MWNT (NH₂‐MWNT). Anhydride‐terminated polyimide (PI) composite films based on NH₂‐MWNT and Di‐MWNT are fabricated by solution blending and consequent planar casting. The exposed amino groups of NH₂‐MWNT create strong covalent bonds with the anhydride‐terminated polyamide acid in the course of N‐acylation and curing chemical reactions. Solubility examinations of nanotubes and morphologies of the composite films indicate that the dispersion of NH₂‐MWNT is significantly better than Di‐MWNT in PI matrix and NH₂‐MWNT can form connected network throughout the PI matrix which makes the NH₂‐MWNT/PI film presenting superior conductivity. Both morphologies and mechanical properties of the composites show that NH₂‐MWNT has stronger interfacial interaction with the PI matrix. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3449–3457     

Crystallization behavior of poly(ε‐caprolactone)/multiwalled carbon nanotube composites

Differential scanning calorimetry (DSC), polarized optical microscopy, and X‐ray diffraction methods were used to investigate the isothermal crystallization behavior and crystalline structure of poly(?‐caprolactone) (PCL)/multiwalled carbon nanotube (MWNT) composites. PCL/MWNT composites were prepared via the mixing of a PCL polymer solution with carboxylic groups containing multiwalled carbon nanotubes (c‐MWNTs). Both Raman and Fourier transform infrared spectra indicated that carboxylic acid groups formed at both ends and on the sidewalls of the MWNTs. A transmission electron microscopy micrograph showed that c‐MWNTs were well separated and uniformly distributed in the PCL matrix. DSC isothermal results revealed that introducing c‐MWNTs into the PCL structure caused strongly heterogeneous nucleation induced by a change in the crystal growth process. The activation energy of PCL drastically decreased with the presence of 0.25 wt % c‐MWNT in PCL/c‐MWNT composites and then increased with increasing MWNT content. The result indicated that the addition of c‐MWNT to PCL induced heterogeneous nucleation (lower total activation energy) at a lower c‐MWNT content and then reduced the transportation ability of polymer chains during crystallization processes at a higher MWNT content (higher total activation energy). A correlation between the crystallization kinetics, melting behavior, and crystalline structure of PCL/c‐MWNT composites was also discussed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 598–606, 2006     

Poly(L‐lactide) crystallization induced by multiwall carbon nanotubes at very low loading

Poly(L ‐lactide) (PLLA)/multiwall carbon nanotube (MWNT) composites were prepared by the solvent‐ultrasonic‐casting method. Only very low concentrations of MWNTs (<0.08 wt %) were added in the composites. Isothermal and nonisothermal crystalline measurements were carried out on PLLA/MWNT composites to investigate the effect of MWNTs on PLLA crystalline behavior. DSC results showed that the incorporation of MWNTs significantly shortened the crystalline induction time and increased the final crystallinity of the composite, which indicated MWNTs have a strong nucleation effect on PLLA even at very low concentrations. The nonisothermal crystallization measurements showed that the MWNTs greatly speed up crystallization during cooling. From isothermal crystallization results, both PLLA and PLLA/MWNT composites samples closely followed a relationship based on Lauritzen‐Hoffman theory, with the regime II to III transition shifting to lower temperature with increasing MWNT concentration. A double melting peak appeared in both nonisothermal and isothermal measurements. The conditions under which it appeared were found to closely depend on the regime II‐III transition temperature obtained from Lauritzen‐Hoffman theory. From the magnitude and position of melting peaks, it is proposed that the double melting peak is caused by a disorder‐order crystal phase transition. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2341–2352, 2009     

Synthesis and characterization of polyaniline/silicon dioxide composites and preparation of conductive films

The focus of this study was to synthesize the inherently conductive polymer polyaniline using an optimized process to prepare polyaniline/silicon dioxide (PANI/SiO₂) composites by in situ polymerization and ex situ solution mixing. PANI and PANI/SiO₂ composite films were prepared by drop‐by‐drop and spin coating methods. The electrical conductivities of HCl doped PANI film and PANI/SiO₂ composite films were measured according to the standard four‐point‐probe technique. The composite films exhibited an increase in electrical conductivity over neat PANI. PANI and PANI/SiO₂ composites were also investigated by spectroscopic methods including UV‐Vis, FT‐IR, and Photoluminescence. UV‐Vis and FT‐IR studies showed that SiO₂ particles affect the quinoid units along the polymer backbone and indicate strong interactions between the SiO₂ particles and the quinoidal sites of PANI (doping effect). The photoluminescence properties of PANI and PANI/SiO₂ composites were studied and the PANI/SiO₂ composites showed increased intensity as compared to neat PANI. The increase of conductivity of PANI/SiO₂ composite may be partially due to the doping or impurity effect of SiO₂ where the silicon dioxides compete with chloride ions. The morphology of particles and films were examined by a scanning electron microscope (SEM). SEM measurements indicated that the SiO₂ were well dispersed and isolated in composite films. Copyright © 2009 John Wiley & Sons, Ltd.     

Influence of graphene reinforcement in conductive polymer: Synthesis and characterization

Lightweight conductive polymers are considered for lightning strike mitigation in composites by synthesizing intrinsically conductive polymers (ICPs) and by the inclusion of conductive fillers in insulating matrices. Conductive films based on polyaniline (PANI) and graphene have been developed to improve through‐thickness conductivity of polymer composites. The result shows that the conductivity of PANI enhanced by blending polyvinylpyrrolidone (PVP) and PANI in 3:1 ratio. Conductive composite thin films are prepared by dispersing graphene in PANI. The conductivity of composite films was found to increase by 40× at 20 wt% of graphene inclusion compared with PVP and PANI blend. Fourier‐transform‐infrared (FTIR) spectra confirmed in situ polymerization of the polymer blend. The inclusion of graphene also exhibits an increase in Tg by 21°C. Graphene additions also showed an increase in thermal stability by approximately 148°C in the composite films. The mechanical result obtained from DMA shows that inclusion of graphene increases the tensile strength by 48% at 20 wt% of graphene reinforcement. A thin, highly conductive surface that is compatible with a composite resin system can enhance the surface conductivity of composites, improving its lightning strike mitigation capabilities.     

Characterization and electrical transport properties of polyaniline and multiwall carbon nanotube composites

Polyaniline/multiwalled carbon nanotube (PANI/MWNT) composites were prepared by in situ polymerization. Scanning electron microscope, X‐ray diffraction, Fourier transform infrared, Uv‐Visible spectroscopy, Fluorescence spectrophotometry were done to characterize the PANI/MWNT composites. Thermal stability was measured by thermogravimetry analysis. The thermal stability of PANI/MWNT composites becomes higher than PANI. Electrical transport properties of different PANI/MWNT composites were investigated in the temperature range 77 ≤ T ≤ 300 K with and without magnetic field up to 1 T. The dc resistivity of PANI/MWNT composites shows different behavior compared to the sample without MWNT. The room temperature dc magnetoconductivity of the samples is negative; however, its sign changes to positive by lowering the temperature, which has been explained by hopping type charge transport. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1767–1775, 2010     

Well-dispersed multi-walled carbon nanotube/polyaniline composite films

Multi-walled carbon nanotube (MWNT)/polyaniline (PANI) composite films with good uniformity and dispersion were prepared by electrochemical polymerization of aniline containing well-dispersed MWNTs. The results of transmission electron microscopy (TEM) show that aniline can be used to solve MWNTs via formation of donor–acceptor complexes. Scanning electron microscopy (SEM), cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) revealed that the well arrangement of PANI-coated MWNTs in these films facilitated improved electron and ion transfer relative to pure PANI films and this may be due to the strong interaction between MWNTs and PANI.     

Polypropylene nanocomposites with various functionalized‐multiwalled nanotubes: thermomechanical properties,morphology, gas permeation,and optical transparency

Polypropylene (PP) nanocomposites with three different functionalized‐multiwalled nanotubes (F‐MWNTs) are compared in terms of their thermomechanical properties, morphology, oxygen permeability, and optical transparency. The F‐MWNTs dodecanol‐MWNT, dodecylamine‐MWNT, and 1,1,1,3,3,3‐hexafluoro‐2‐phenyl‐2‐propanol‐MWNT were combined with PP to produce hybrid films. The variations of their properties with the matrix polymer F‐MWNT content are discussed. Transmission electron microscopy photographs show that most of the F‐MWNTs are dispersed homogeneously in the matrix polymer on the nanoscale, although some agglomerated F‐MWNT particles are formed. Even composites with low F‐MWNT contents (≤3 wt %) exhibit much better thermomechanical values than pure PP. The gas permeability of the hybrids was found to decrease linearly with increases in the F‐MWNT content of the PP matrix. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010