New method for post-processing crosslinking reaction

A new processing method to process functionalized polymer materials that are able to crosslink has been developed. The crosslinking reaction occurs after the melt processing stage at moderate temperature and without the addition of external reagents. Maleic anhydride-ethylene copolymer was processed with 1,4-butanediol in the presence of para-toluene sulfonic acid as catalyst. To prevent the reaction in the melt, it was chosen to trap the 1,4-butanediol onto vector particles. The extent of the crosslinking reaction during the mixing at 110 °C has been studied for three different particles taken as vector particles. It was found that Orgasol^® polyamide particles are efficient to inhibit the crosslinking reaction in the mixer. The reaction then takes place at 40 °C and after 100 h the cured samples appeared to be highly and homogeneously crosslinked with a gel content above 90%.     

Radiochemical ageing of poly(ether ether ketone)

Thin (60 μm) and thick (250 μm) samples of poly(ether ether ketone) were subjected to radiochemical ageing at 24 kGy h⁻¹ dose rate for doses up to 30.7 MGy at 60 °C in air. FTIR spectrophotometry (hydroxyl and carbonyl build-up), ATR microscopy (oxidation profiles), ammonia gaseous treatment (determination of carbonyl nature), density, DSC (glass transition temperature, cold crystallization and melting point changes), and gel content measurements (crosslinking) were conducted for examination of polymer degradation. Thin samples were shown to undergo principally chain scission process whereas thick ones undergo mainly crosslinking. This difference can be attributed to the kinetic control of oxidation by oxygen diffusion. A mechanistic scheme was proposed from radiochemical yields estimations.     

Degradation of pre-aged polymers exposed to simulated recycling: Properties and thermal stability

Accelerated thermal and photo-aging of four homopolymers, low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and high-impact polystyrene (HIPS), was performed and the impact of subsequent reprocessing conditions on their properties studied. Polymer samples oven-aged at 100 °C for varying periods of time or UV irradiated in a Weather-o-meter (WOM) at λ = 340 nm were reprocessed in a Brabender plasticorder at 190 °C/60 rpm for 10 min. Chemical changes and the evolution of rheological and mechanical properties accompanying the gradual degradation of the individual polymers were monitored and evaluated (DSC, FTIR, colorimetric method, MFI, tensile impact strength). LDPE and HIPS were found to be more susceptible to thermo-oxidation than HDPE and PP, whereas HDPE and PP were affected to a greater extent by UV exposure; the crucial role here is being played by the stabilization of the studied resins. In HDPE the scission and crosslinking reactions competed both in thermo-and photo-degradation. In the case of LDPE, scission prevailed over branching during thermo-oxidation, whereas photo-oxidation of the same sample led predominantly to crosslinking. Abrupt deterioration of the LDPE rheological properties after one week of thermal exposure was suppressed by re-stabilization. The scission reaction was also predominant for PP during thermo-oxidation, and it took place even faster during UV exposure. In the case of HIPS a slight photo-degradation of PS matrix is accompanied by simultaneous crosslinking of the polybutadiene component.     

A study of the synthesis and characterization of ethylene/dicyclopentadiene copolymers using a metallocene catalyst

Copolymers of ethylene/dicyclopentadiene were produced using a Me₂Si(Ind)₂ZrCl₂/methylaluminoxane catalyst system. The melting and crystallization points of the freshly prepared copolymers steadily decreased with increasing comonomer concentration. This was attributed to increased comonomer concentration in the polymer. When the comonomer incorporation, as measured by ¹³C NMR, is plotted against the comonomer concentration in the reactor, a plateau appears at concentrations higher than 0.12 mol/L. At concentrations greater than 0.12 mol/L time dependant crosslinking begins to be observed in the copolymers after exposure to air for several months. This crosslinking is also apparent in the thermosetting behavior of the copolymers when they are allowed sufficient time to crosslink. Copolymers with lower comonomer concentrations possess melting enthalpies even after several weeks, suggesting that there is a threshold concentration of 0.12 mol/L for the crosslinking process. Tensile tests of thermoplastic samples showed that incorporation of ca. 5 mol% of comonomer into the polyethylene main chain results in a semi-elastomeric material which possesses high strain recovery and whose strain hardening is similar to that observed for the homopolymer.     

Effect of crosslinking on the properties of composites based on LDPE and conducting organic filler

New types of composites were prepared using low-density polyethylene (LDPE) filled with modified organic filler, Canadian switch grass coated with polypyrrole (PPy). The grass surface was entirely covered when 10 wt.% of pyrrole was used for the modification, as confirmed by scanning electron microscopy and infrared spectroscopy. LDPE composites filled with modified grass were prepared by melt mixing and their properties were compared with the properties of the composites filled with unmodified grass. The influence of crosslinking, induced by 1 wt.% of peroxide, on mechanical, thermal and electrical properties of the composites was investigated. Crosslinking enhanced the tensile strength of the prepared composites in the entire range of the filler content. The Young’s modulus of the composites prepared by crosslinking is slightly lowered when compared with the uncrosslinked composites if the filler content is less than 60 wt.%, for higher filler content it is increased. The conductivity of the uncrosslinked composites containing 40 wt.% of grass modified by PPy was in the range 1 × 10⁻⁶ S cm⁻¹, which is a value by 5 orders of magnitude higher than the conductivity of the crosslinked materials. The presence of PPy on grass surface leads to a reduction of crosslinking of the LDPE matrix.     

Development of a biosensor for caffeine

We have utilized a microbe, which can degrade caffeine to develop an Amperometric biosensor for determination of caffeine in solutions. Whole cells of Pseudomonas alcaligenes MTCC 5264 having the capability to degrade caffeine were immobilized on a cellophane membrane with a molecular weight cut off (MWCO) of 3000-6000 by covalent crosslinking method using glutaraledhyde as the bifunctional crosslinking agent and gelatin as the protein based stabilizing agent (PBSA). The biosensor system was able to detect caffeine in solution over a concentration range of 0.1 to 1 mg mL⁻¹. With read-times as short as 3 min, this caffeine biosensor acts as a rapid analysis system for caffeine in solutions. Interestingly, successful isolation and immobilization of caffeine degrading bacteria for the analysis of caffeine described here was enabled by a novel selection strategy that incorporated isolation of caffeine degrading bacteria capable of utilizing caffeine as the sole source of carbon and nitrogen from soils and induction of caffeine degrading capacity in bacteria for the development of the biosensor. This biosensor is highly specific for caffeine and response to interfering compounds such as theophylline, theobromine, paraxanthine, other methyl xanthines and sugars was found to be negligible.Although a few biosensing methods for caffeine are reported, they have limitations in application for commercial samples. The development and application of new caffeine detection methods remains an active area of investigation, particularly in food and clinical chemistry. The optimum pH and temperature of measurement were 6.8 and 30 ± 2 °C, respectively. Interference in analysis of caffeine due to different substrates was observed but was not considerable. Caffeine content of commercial samples of instant tea and coffee was analyzed by the biosensor and the results compared well with HPLC analysis.     

Direct determination of uranium in seawater by laser fluorimetry

A method for estimation of uranium in seawater by using steady state laser flourimetry is described. Uranium present in seawater, in concentration of approximately 3 ng ml⁻¹ was estimated without prior separation of matrix. Quenching effect of major ions (Cl⁻, Na⁺, SO₄⁻, Mg⁺, Ca⁺, K⁺, HCO₃⁻, Br⁻) present in seawater on fluorescence intensity of uranium was studied. The concentration of phosphoric acid required for maximum enhancement of fluorescence intensity was optimized and was found to be 5%. Similarly the volume of concentrated nitric acid required to eliminate the quenching effect of chloride and bromide completely from 5 ml of seawater were optimized and was found to be 3 ml. A simple equation was derived using steady state fluorescence correction method and was used for calculation of uranium concentration in seawater samples. The method has a precesion of 1% (1 s, n = 3). The values obtained from laser fluorimetry were validated by analyzing the same samples by linear sweep adsorptive stripping voltametry (LSASV) of the uranium-chloranilic acid (2,5-dichloro-3,6-dihydroxy-1,4-benzoquinone) complex. Both the values are well in agreement.     

Multiply ionization of diethyl ether clusters by 532 nm nanosecond laser: The influence of laser intensity and the electron energy distribution

The formation mechanism for multiply charged ions (C^q+ and O^q+ (q = 2–4)) were investigated using a dual polarity time-of-flight mass spectrometer when diethyl ether clusters interacted with nanosecond laser pulse. The signal intensity of multiply charged ions and electron energy was measured experimentally. It was shown that the intensity of multiply charged ions increased about 50 times when laser intensity increased from 7.6 × 10⁹ to 7.0 × 10¹⁰ W/cm², then saturated as laser intensity increased further. It is interesting that the evolution of the mean value of electron energy was same to that of multiply charged ions. The theoretical calculation showed the ionization potential of atomic ions could be significantly decreased due to the effect of Coulomb screening especially at low laser intensity. It indicated that the electron ionization combined with Coulomb screening effect could explain the production of multiply charged ions in nanosecond laser field.     

Determination of lead in environmental water by a backward light scattering technique

An optical fiber assembly developed in our laboratory, which is based on detecting backward light scattering (BLS) signals, is now applied to detect the lead content in environmental samples. Due to effectively eliminating the interference of reflected light, this BLS signals based detection assembly can be used to determine analyte directly. In HAc-NaAc buffer medium (pH 4.8), the interaction of lead and sodium tetraphenylboron (TPB) in the presence of polyethylene glycol (PEG) yields large particles of ternary complex, resulting in strong enhanced backward light scattering (BLS) signals characterized at 371 nm. By measuring the BLS signals with the homemade optical fiber assembly coupled with a common spectrofluorometer, we found that the enhanced BLS intensity is proportional to lead content over the range of 0.03-1.0 μg ml⁻¹ with the limit of determination (LOD) of 2.6 ng ml⁻¹. Three artificial water samples containing various coexistent substances were detected with the recovery of 90.1-107.5%. Standard addition method was used to detect the lead content in drink tap water, and found that the lead is hardly to detect due to too low content. Prior enrichment should be made in order to detect river water samples, and it was found that the content of lead in Jialing River at Bebei Dock is about 14 ng ml⁻¹, identical to the results using inductively coupled plasma atomic emission spectrometry (ICP-AES).     

Comparative imaging of P,S, Fe,Cu, Zn and C in thin sections of rat brain tumor as well as control tissues by laser ablation inductively coupled plasma mass spectrometry

Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) was used for quantitative imaging of selected elements (P, S, Fe, Cu, Zn and C) in thin sections of rat brain samples (thickness 20 μm). The sample surface was scanned (raster area ~ 2 cm²) with a focused laser beam (wavelength 266 nm, diameter of laser crater 50 μm, and irradiance 1 × 10⁹ W cm^− 2). The laser ablation system was coupled to a double-focusing sector field. The possibility was evaluated of using carbon (via measurement of ¹³C⁺) as an internal standard element for imaging element distribution as part of this method. The LA-ICP-MS images obtained for P, S, Fe Cu and Zn were quantified using synthetically prepared matrix-matched laboratory standards. Depending on the sample analyzed, concentrations of Cu and Zn in the control tissue were found to be in the range of 8–10 μg g^− 1 and 10–12 μg g^− 1, while in the tumor tissue these concentrations were in the range of 12–15 μg g^− 1 and 15–17 μg g^− 1, respectively. The measurements of P, S and Fe distribution revealed the depletion of these elements in tumor tissue. In all the samples, the shape of the tumor could be clearly distinguished from the surrounding healthy tissue by the depletion in carbon. Additional experiments were performed in order to study the influence of the water content of the analyzed tissue on the intensity signal of the analyte. The results of these measurements show the linear correlation (R² = 0.9604) between the intensity of analyte and amount of water in the sample. The growth of a brain tumor was thus studied for the first time by imaging mass spectrometry.     

CO2Laser Photochemical Hole Burning in the IR Reflection Spectra of Crystalline Natural Silicates

Structural and chemical transformations induced on the surface of crystalline natural silicates by pulse ₂laser radiation with a pulse length of 200 ns and an energy per pulse of 2 J were examined. The IR reflection spectra of nepheline KNa₃[AlSiO₄]₄and rhodonite CaMn₄[Si₅O₁₅] were measured before and after exposure to laser radiation. An increase in the reflectance at the laser frequency used was observed, which was named hole burning in the IR reflection spectra of specimens. A 50-cm^–1wide hole was shown to be burnt at a frequency coinciding with that of a laser radiation line within this width. At the incident laser frequency, a narrow, 5-cm^–1wide hole is also burnt in the IR spectra of the irradiated samples. The burning of the 50-cm^–1hole was assumed to be due to the selective sublimation of Si_mO_ncomplexes. The burning of the narrow hole of 5 cm^–1width is associated with the laser-induced selective dissociation of Si–O bonds in the near-surface layer at the frequency employed.     

Nonisothermal crystallisation, melting behavior and wide angle X-ray scattering investigations on linear low density polyethylene (LLDPE)/ethylene vinyl acetate (EVA) blends: effects of compatibilisation and dynamic crosslinking

Crystallisation studies on LLDPE/EVA blends and the individual components were performed with wide angle X-ray scattering (WAXS) technique and differential scanning calorimetry (DSC) DSC was used to characterise the quiescent crystallisation behavior. The heat of fusion and crystallinity of the blends were reduced by the addition of EVA. The experimental and theoretical values of crystallinity of the blends were found to be mutually agreeing. Crystallisation of LLDPE remains impeded to some extent due to the presence of amorphous EVA. Compatibilisation does not affect crystallinity whereas crosslinking decreases crystallinity. Crosslinking and compatibilisation make no significant change in the melting temperature of the blends. X-ray diffraction studies were carried out on un-crosslinked and crosslinked LLDPE/EVA blends with a view to study the effect of blend composition and crosslinking on crystallinity and lattice distance. Studies revealed that LLDPE and EVA have orthorhombic unit cell. Blending with EVA did not affect the crystalline structure of LLDPE, but the crystallinity decreases with EVA content. At low concentrations of EVA the lattice parameters remain unchanged. Above 30% EVA content however, a linear increase has been observed. Dicumyl peroxide (DCP) crosslinked samples show considerable shift of (1 1 0), (2 0 0) and (0 2 0) crystalline peaks towards lower 2θ values indicating an increase of unit cell parameters of the orthorhombic unit cell of polyethylene. At lower EVA-concentrations (<50%) the crystalline structure remains unchanged. For EVA-contents of more than 70% however, increasing DCP-content reduces the crystallinity of the blends and increases the lattice distance. This indicates that DCP-crosslinking is more effective in EVA phase than in the LLDPE phase.     

Resonantly laser induced plasmas in gases: The role of energy pooling and exothermic collisions in plasma breakdown and heating

The present work is a systematic experimental study of the plasma formation in cesium vapor induced by a continuous laser tuned to the resonance transition 6S_1/2–6P_3/2. Taking into account the measured absolute population densities of Cs ground and excited state atoms as well as the electron densities derived from Stark broadening of the Cs lines, complete local thermodynamic equilibrium in the laser-produced plasma was found for laser power densities ≈ 10 Wcm^− 2 at cesium ground state number densities of about 10¹⁷ cm^− 3. Direct conversion of the excitation energy or parts of the excitation energy in exothermic collisions of laser-excited atoms is concluded to be the major process for atomic vapor heating and subsequent formation of LTE plasmas.     

Synthesis and applications of diethylstilbestrol-based molecularly imprinted polymer-coated hollow fiber tube

A novel molecularly imprinted polymer-coated polypropylene hollow fiber tube (MIP-HFT) was photoinitiated for the copolymerization of diethylstilbestrol (DES) as a template molecule, α-methacrylic acid as a functional monomer, and ethylene glycol dimethacrylate as a crosslinking agent. The characteristics and applications of the MIP-HFT were investigated. In order to compare its characteristics with those of a non-imprinted polymer-immersed hollow fiber tube, the selectivity of the MIP-HFT was investigated using dienestrol and hexestrol as the structural analogues of a DES template, and phenol and methylbenzene were taken as reference compounds. The MIP-HFT was employed in the HPLC analysis of spiked milk samples. The detection limits of the method were found to be in the range 2.5-3.3 μg L⁻¹ for DES, dienestrol and hexestrol and the RSD% were in the range 6.4-8.9. The limits of quantitation were found to be in the range 8.7-9.4 μg L⁻¹ in milk for DES, dienestrol and hexestrol, and their average recoveries were 83.7-90.6% in the spiked milk samples. The experimental results revealed that the MIP-HFT provides a good carrier for the selective adsorption of DES and its chemical structure analogs, and can be used for the preconcentration of these compounds in complicated samples.     

Glass particles produced by laser ablation for ICP-MS measurements

Pulsed laser ablation (266 nm) was used to generate glass particles from two sets of standard reference materials using femtosecond (150 fs) and nanosecond (4 ns) laser pulses with identical fluences of 50 J cm⁻². Scanning electron microscopy (SEM) images of the collected particles revealed that there are more and larger agglomerations of particles produced by nanosecond laser ablation.In contrast to the earlier findings for metal alloy samples, no correlation between the concentration of major elements and the median particle size was found. When the current data on glass were compared with the metal alloy data, there were clear differences in terms of particle size, crater depth, heat affected zone, and ICP-MS response. For example, glass particles were larger than metal alloy particles, the craters in glass were less deep than craters in metal alloys, and damage to the sample was less pronounced in glass compared to metal alloy samples. The femtosecond laser generated more intense ICP-MS signals compared to nanosecond laser ablation for both types of samples, although glass sample behavior was more similar between ns- and fs-laser ablation than for metal alloys.     

Flow injection chemiluminescence determination of the total phenolics levels in plant-derived beverages using soluble manganese(IV)

This study established a flow injection (FI) methodology for the determination of the total phenolic content in plant-derived beverages based on soluble manganese(IV) chemiluminescence (CL) detection. It was found that mixing polyphenols with acidic soluble manganese(IV) in the presence of formaldehyde evoked chemiluminescence. Based on this finding, a new FI-CL method was developed for the estimation of the total content of phenolic compounds (expressed as milligrams of gallic acid equivalent per litre of drink) in a variety of wine, tea and fruit juice samples. The proposed method is sensitive with a detection limit of 0.02 ng mL⁻¹ (gallic acid), offers a wide linear dynamic range (0.5-400 ng mL⁻¹) and high sample throughput (247 samples h⁻¹). The relative standard deviation for 15 measurements was 3.8% for 2 ng mL⁻¹ and 0.45% for 10 ng mL⁻¹ of gallic acid. Analysis of 36 different samples showed that the results obtained by the proposed FI-CL method correlate highly with those obtained by spectrophotometric methods commonly used for the evaluation of the total phenolic/antioxidant level. However, the FI-CL method was found to be far simpler, more rapid and selective, with almost no interference from non-phenolic components of the samples examined.     

The use of inverse gas chromatography to study surface thermal oxidation of polypropylene

Thermo-oxidative effects on the surface energy of polypropylene were measured by inverse gas chromatography as a function of exposure time and temperature. Unaltered polypropylene had a surface energy of 33 mJ/m². Oxidized polypropylene, after exposure to air at temperatures of 100 °C and 110 °C, had a range of maximum surface energies from 38 to 41 mJ/m². Comparisons between FTIR carbonyl peak growth and the surface energy showed that both methods detect oxidation, though the increase in surface energy is detected before the carbonyl peak growth is noticeable. The work of adhesion predicted by the surface free energies obtained in this work between a coated calcium carbonate and polypropylene changes by 10% due to the oxidation of the polymer at 110 °C.     

Preparation and adsorption kinetics of porous γ-glycidoxypropyltrimethoxysilane crosslinked chitosan–β-cyclodextrin membranes

Porous structured chitosan–β-cyclodextrin membranes were synthesized by incorporating β-cyclodextrin polymers as the functional reagent and using γ-glycidoxypropyltrimethoxysilane as crosslinking agent. Compared with chitosan itself, the synthesized membranes showed significant changes in the molecular constitutions, crystalline and thermal properties. It was found that the mol ratio of the epoxy groups of γ-glycidoxypropyltrimethoxysilane to the free amino groups of chitosan, as well as the solvent evaporated time, largely influenced the pore size and water content of the membranes. The effects of the initial concentration of adsorbate and the pH on the adsorption of hydroquinone were investigated by the spectrophotometry. Kinetic studies show the adsorption is a pseudo-second order process. The adsorption is endothermic and chemically activated reaction with activation energy of 70.0 kJ mol⁻¹.     

Development of a non-labeled immunosensor for the herbicide trifluralin via optical waveguide lightmode spectroscopic detection

A highly sensitive immunosensor using optical waveguide lightmode spectroscopy (OWLS) was developed for the detection of the herbicide trifluralin. OWLS as an in situ and label free method of detection, based on the measurement of the diffraction of a linearly polarized laser beam (He-Ne laser, 632.8 nm) on a diffraction grating in a thin waveguide layer (SiO₂-TiO₂), offered means to produce immunosensors utilizing immobilized antibodies raised against trifluralin allowing a non-competitive biosensor, or immobilized trifluralin conjugate allowing a competitive biosensor for this analyte. Immobilization of molecules sensitizing the sensor was undertaken on amino silanized waveguide surfaces in a two-step procedure using glutaraldehyde. Within the immobilized antibody (Ab) based immunosensor the signal measured was proportional to the trifluralin content in the samples, but the method allowed detection of trifluralin only above 100 ng ml⁻¹ due to the small molecular size of the antigen (Ag). In the immobilized antigen based immunosensor, a trifluralin-bovine serum albumin (BSA) conjugate was covalently linked to the waveguide surface. During measurements the standard solutions and samples were mixed in 1:1 ratio with antiserum, containing constant amounts of antibodies. The amount of free antibodies bound to the surface was inversely proportional to the trifluralin content of the solutions measured. The immobilized antigen based method allowed detection of trifluralin in the concentration range of 2×10⁻⁷ to 3×10⁻⁵ ng ml⁻¹. Results of trifluralin determinations were compared to those obtained in parallel enzyme-linked immunosorbent assay (ELISA) tests and in gas chromatorgraphic-mass spectrometric (GC-MS) analyses, and indicated an increase of six orders of magnitude in the limit of detection (LOD).     

Localized surface plasmon resonance sensing detection of glucose in the serum samples of diabetes sufferers based on the redox reaction of chlorauric acid

In this paper, the formation of gold nanoparticles (Au NPs) as a result of the thermo-active redox reaction of chlorauric acid (HAuCl₄) and glucose in alkaline medium was identified by measuring the plasmon resonance absorption, localized surface plasmon resonance (LSPR), and transmission electron microscopy (TEM) images, for the formation of Au NPs displays characteristic plasmon resonance absorption bands and corresponding LSPR signals. It was found that the resulted LSPR signals could be easily detected with a common spectrofluorometer. With increasing glucose concentration, the LSPR intensity displays linear response with the glucose content over the range from 2.0 to 250.0 μmol l⁻¹. Thus, a novel assay of glucose was established with the limits of determination (3σ) being 0.21 μmol l⁻¹, and the detection of glucose could be made easily in the serum samples of diabetes sufferers. Mechanism investigations showed that the activation energy and molar ratio of the reaction were 34.8 kJ mol⁻¹ and 3:2, respectively.