A functionalized gold nanoparticles and Rhodamine 6G based fluorescent sensor for high sensitive and selective detection of mercury(II) in environmental water samples

A gold-nanoparticles (Au NPs)-Rhodamine 6G (Rh6G) based fluorescent sensor for detecting Hg (II) in aqueous solution has been developed. Water-soluble and monodisperse gold nanoparticles (Au NPs) has been prepared facilely and further modified with thioglycolic acid (TGA). Free Rh6G dye was strongly fluorescent in bulk solution. The sensor system composing of Rh6G and Au NPs fluoresce weakly as result of fluorescence resonance energy transfer (FRET) and collision. The fluorescence of Rh6G and Au NPs based sensor was gradually recovered due to Rh6G units departed from the surface of functionalized Au NPs in the presence of Hg(II). Based on the modulation of fluorescence quenching efficiency of Rh6G-Au NPs by Hg(II) at pH 9.0 of teraborate buffer solution, a simple, rapid, reliable and specific turn-on fluorescent assay for Hg(II) was proposed. Under the optimum conditions, the fluorescence intensity of sensor is proportional to the concentration of Hg(II). The calibration graphs are linear over the range of 5.0 × 10⁻¹⁰ to 3.55 × 10⁻⁸ mol L⁻¹, and the corresponding limit of detection (LOD) is low as 6.0 × 10⁻¹¹ mol L⁻¹. The relative standard deviation of 10 replicate measurements is 1.5% for 2.0 × 10⁻⁹ mol L⁻¹ Hg(II). In comparison with conventional fluorimetric methods for detection of mercury ion, the present nanosensor endowed with higher sensitivity and selectivity for Hg(II) in aqueous solution. Mercury(II) of real environmental water samples was determined by our proposed method with satisfactory results that were obtained by atomic absorption spectroscopy (AAS).     

Enhanced plasmon resonance light scattering signals of colloidal gold resulted from its interactions with organic small molecules using captopril as an example

Gold nanoparticles are known for their plasmon resonance absorption (PRA) depending on their size. Our this investigation shows that plasma resonance light scattering (PRLS) signals in the corresponding PRA region could be measured using a common spectrofluorometer, and be enhanced when aggregation of gold nanoparticles occurs due to their interaction with organic small molecules (OSMs). Using captopril (Cap) as an example, we investigated the interactions of gold nanoparticles with OSMs in order to propose a general method of OSMs such as typical clinic organic drugs. In aqueous medium of pH 2.09, there are about 2.2 × 10³ Cap molecules covalently binding to the surface of a 10-nm diameter gold nanoparticle through the thiol functional group of Cap, and thus forms a core-shell assembly of [(Au)₃₁₀₀₀]@[(Cap)₂₂₀₀], displaying strong enhanced PRLS signals in the PRA region of gold colloid. The PRLS intensities characterized at 553.0 nm were found to be proportional to the concentration of Cap over the range of 0.1-1.7 mg L⁻¹ with the determination limit (3σ) of 32.0 μg L⁻¹. With that, Cap in pharmaceutical preparations could be determined with the recovery of 97.0-104.5% and R.S.D. of less than 2.4%.     

A quantitative method for determination of Co(II) based on the inner filter effect of reagents on the Raman scattering signals of water

It is known that Raman scattering signals are one of main interference sources leading up to determination errors in spectrofluorometry, and thus the signals can be easily detected with a common spectrofluorometer. In this contribution, we propose a quantitative method based on the inner filter effect (IFE) of reagents on the Raman scattering signals of solvent by taking the complexation of divalent cobalt ion with 4-[(5-chloro-2-pyridyl)azo]-1,3-diaminobenzene (5-Cl-PADAB) as a model system. By adjusting the excitation wavelength of the spectrofluorometer, we could easily detect the Raman scattering signals of water at 424 nm where the maximum absorption of 5-Cl-PADAB reagent is located. In a solution of 5-Cl-PADAB, the Raman scattering signals of water are decreased owing to the IFE of 5-Cl-PADAB. If Co(II), which could form the binary complex of Co(II)/5-Cl-PADAB and consumes the 5-Cl-PADAB reagent, is present in such a case for a given amount of 5-Cl-PADAB solution, recovered Raman scattering signals could be observed and measured with a spectrofluorometer. It was found that the intensity of the enhanced Raman scattering signals is proportional to the Co(II) concentration over the range from 2.0 × 10⁻⁷ mol L⁻¹ to 1.0 × 10⁻⁵ mol L⁻¹, and the detection limit could reach 1.2 × 10⁻⁷ mol L⁻¹. With that, Co(II) in samples could be detected with R.S.D. values lower than 2.6% and recoveries over the range of 97.2-104.7%.     

Synchronous fluorescence determination of DNA based on the interaction between methylene blue and DNA

The fluorescence intensity of methylene blue (MB) quenched by DNA in the pH range of 6.5-8.0 was studied with synchronous fluorescence technology. A novel method for detecting single-stranded and double-stranded DNA was developed. The decreased fluorescence intensity at 664 nm is in proportion to the concentration of DNA in the range of 0.28-11.0 μmol L⁻¹ for ctDNA, 0.14-8.25 μmol L⁻¹ for thermally denatured ctDNA and 0.28-8.25 μmol L⁻¹ for hsDNA. The detection limits (S/N = 3) are 0.11, 0.04 and 0.04 μmol L⁻¹, respectively. The method is rapid, selective, and the reagents are lower toxic. It has been used for the determination of DNA in synthetic samples with good satisfaction. In addition, the interaction modes between MB and ctDNA and the mechanism of the fluorescence quenching were also discussed in detail. The experimental results from absorption spectra and fluorescence polarization indicate that the possible interaction modes between MB and DNA are the electrostatic binding and the intercalation binding.     

Performance of the diffusive gradients in thin films technique for measurement of trace metals in low ionic strength freshwaters

A series of experiments were undertaken to investigate the effect of ionic strength and the concentration of free sodium ions in the resin gel on the performance of the diffusive gradients in thin films (DGT) technique. When the free sodium ion concentration in the resin gel was estimated by the time-dependent release into solution, it agreed with a previous estimate. However, equilibration with different volumes of water gave a higher value, suggesting that inherent averaging in the time-dependent release method underestimates the free concentration. DGT measurements of Cu and Cd were made over a wide range of ionic strengths (from 3 μmol l⁻¹ to 0.8 mol l⁻¹). For all the ionic strengths above 100 μmol l⁻¹ there was no significant difference between measurements made by DGT and measurements made directly on the solution using atomic absorption spectroscopy. Below 100 μmol l⁻¹ results were erratic. They did not comply with a theory that predicts high results for DGT based on enhancement of the diffusion coefficient of trace metal cations by counter diffusion of sodium ions. When Cd in solutions with a range of ionic strengths was measured by DGT there was no difference whether the resin gels were in Na or Ca form. Rather than counter diffusion of Na ions, it is suggested that the spurious behaviour at low ionic strength is due to interactions of the trace metals with the diffusion gel when there are insufficient excess cations present.     

Determination of adrenaline by using inhibited Ru(bpy)3 electrochemiluminescence

Adrenaline was found to inhibit strongly the electrochemiluminescence (ECL) from the Ru(bpy)₃²⁺/tripropylamine system when a working Pt electrode was maintained at 1.05 V (versus Ag/AgCl) in pH 8.0 phosphate buffer. On this basis, a flow injection (FI) procedure with inhibited electrochemiluminescence detection has been developed for determination of adrenaline. The method exhibited a good reproducibility, sensitivity, and stability with a detection limit (signal-to-noise ratio = 3) of 7.0×10⁻⁹ mol l⁻¹ and dynamic concentration range of 2×10⁻⁸ to 1×10⁻⁴ mol l⁻¹. The relative standard deviation was 2.2% for 1.0×10⁻⁶ mol l⁻¹ adrenaline (n=11). The method was successfully applied to the determination of adrenaline in pharmaceutical samples. Moreover, ECL emission spectra, UV-Vis absorption spectra and cyclic voltammograms of Ru(bpy)₃²⁺/tripropylamine/adrenaline were studied. The inhibition mechanism has been proposed as the interaction of electrogenerated Ru(bpy)₃^2+* and the o-benzoquinone derivatives, adrenochrome and adrenalinequinone, at the electrode surface.     

Diamond paste based electrodes for the determination of Pb(II) at trace concentration levels

Three types of monocrystalline diamond: natural diamond 1 μm, synthetic diamond 50 μm (synthetic-1), and synthetic diamond 1 μm (synthetic-2) were used for electrodes’ construction. The linear concentration ranges recorded for Pb(II), when natural diamond, synthetic-1 and synthetic-2 based electrodes were used were between 10⁻⁹ and 10⁻⁶; 10⁻¹⁰ and 10⁻⁷; and between 10⁻¹⁰ and 10⁻⁸ mol l⁻¹, respectively. Low detection limits which lie between 10 and 100 pmol l⁻¹ proves the sensitivity of the electrodes. It was found that Pb(II) yielded a peak at about +0.3±0.02 V (versus Ag/AgCl) for all the electrodes. Lead was determine with high reliability from water and tea samples at trace concentration levels using the proposed diamond paste based electrodes.     

Spectrophotometric catalytic determination of Fe(III) in estuarine waters using a flow-batch system

A flow-batch system was developed for the determination of Fe(III) in estuarine waters with high variability in salinity. The method is based on the catalytic effect of iron(III) on the oxidation rate of N,N-dimethyl-p-phenylenediammonium dichloride (DmPD) by hydrogen peroxide and the formed product is spectrophotometrically monitored at 554 nm. A controlled addition of sodium chloride to every assayed sample is accomplished for in-line individual salinity matching.The proposed system processes about 30 samples h⁻¹ and yields reproducible results. Relative standard deviations were estimated as <1.5% after 10 injections of typical samples (10.0-50.0 μg l⁻¹ Fe; ca. 0.5 mol l⁻¹ Cl). Synthetic samples (15.0 μg l⁻¹ Fe; 0.25-1.0 mol l⁻¹ NaCl) were efficiently processed, and no significant differences in results were found at a probability level of 99.7%. The method works for the full range of salinities. Only 120 μg DmPD are consumed per determination. The analytical curve is linear up to about 60 μg l⁻¹ Fe (r>0.999; n=5) and the detection limit is 5 μg l⁻¹ Fe. Results are in agreement with graphite furnace atomic absorption spectrometry.     

Chemiluminometric photo-induced determination of Strychnine in a Multicommutation flow assembly

This paper deals on the determination of Strychnine, a potent and dangerous pesticide and the analytical procedure is based on the photo-induced chemiluminescence of the pesticide by means of the Multicommutation continuous-flow methodology. Small segments of the pesticide solution were sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. The required time of UV irradiation was obtained by stopped-flow during 150 s; then, the resulting solution formed alternated segments with the oxidizing solution containing 5 × 10⁻³ mol l⁻¹ Ce(IV) in 0.6 mol l⁻¹ nitric acid. The calibration range, from 2 μg l⁻¹ to 50 mg l⁻¹, resulted in a linear behaviour over the range 25 μg l⁻¹ to 20 mg l⁻¹ and fitting the equation: I = 4706x + 624 with a correlation coefficient of 0.9955. The limit of detection was 2 μg l⁻¹ and the sample throughput 15 h⁻¹. After testing the influence of a large series of potential interferents, the method was applied to different kinds of samples.     

Ultrasensitive optical detection of trinitrotoluene by ethylenediamine-capped gold nanoparticles

This study found that 1,2-ethylenediamine (EDA) as a primary amine could be modified onto the surface of citrate-stabilized gold nanoparticles (Au NPs), and the EDA-capped Au NPs were successfully used as an ultrasensitive optical probe for TNT detection. The strong donor–acceptor (D–A) interactions between EDA and trinitrotoluene (TNT) at the Au NP/solution interface induced significant aggregation of the EDA-capped Au NPs, and enabled to easily realize the direct colorimetric detection of ultratrace TNT. The results showed that such a color change was readily seen by the naked eye, and the colorimetric detection could be down to 400 pM level of TNT with excellent discrimination against other nitro compounds. UV–vis absorption spectroscopy was used to examine the TNT-induced changes in local surface plasmon resonance (LSPR) of EDA-capped Au NPs, and a new LSPR band at ca. 630 nm arose along with the addition of TNT, which produced a detection limit of TNT down to ca. 40 pM. Furthermore, dynamic light scattering measurements evidenced the ultratrace TNT-induced small changes in the size of the EDA-capped Au NPs, and realized the quick and accurate detection of TNT in 0.4 pM level. These results demonstrated the ultrahigh sensitivity of this optical probe for TNT detection. Moreover, this optical probe is sample, stable, low-cost, and these excellent properties make it quite promising for infield and rapid detection of TNT.     

p-Dimethylaminobenzaldehyde thiosemicarbazone: a simple novel selective and sensitive fluorescent sensor for mercury(II) in aqueous solution

A novel and simple fluorophore, p-dimethylaminobenzaldehyde thiosemicarbazone (DMABTS), was prepared in order to find available fluorescent chemosensor for mercuric ion in aquesous solution. DMABTS emitted fluorescence at 448 nm in aqueous solution and its fluorescence intensity was completely quenched upon interaction with Hg²⁺ ions, which should be attributed to the 1:1 complex formation between DMABTS and Hg²⁺. The binding constant of the complex was determined as 7.48 × 10⁶ mol l⁻¹. The linear range of quantitative detection of 0 to 5.77 × 10⁻⁶ mol l⁻¹ and the detection limit of 7.7 × 10⁻⁷ mol l⁻¹ for Hg²⁺ in the 6.3 × 10⁻⁶ mol l⁻¹ DMABTS aqueous solution were obtained from a calibration curve. The coexistence of several transition metal ions and anions did interfere the fluorometric titration of Hg²⁺ ion by less than 4% in the emission change.     

Direct determination of lead in produced waters from petroleum exploration by electrothermal atomic absorption spectrometry X-ray fluorescence using Ir-W permanent modifier combined with hydrofluoric acid

The present work reports the development of a methodology for the direct determination of lead in high saline waters derived from petroleum exploration employing electrothermal atomic absorption spectrometry with permanent Ir-W and HF as modifiers. These waters, so-called produced waters, have complex composition containing several types of organic and inorganic substances. In order to attain best conditions (highest analytical signal besides lowest background) for the methodology studies about the effect of several variables and the convenient calibration strategy were performed. Also, the efficiency of other modification approaches was evaluated. At best conditions, pyrolysis and atomization temperature were 800 and 2200 °C, respectively, when the modifiers cited above were utilized. Obtained results indicate that, in this kind of sample, lead can be determined by standard addition method or employing external calibration with standard solutions prepared in 0.8 mol l⁻¹ NaCl medium. In order to evaluate the accuracy of the procedure, a recovery test was performed with six spiked samples of produced waters. The detection limit, quantification limit and the relative standard deviation in 0.8 mol l⁻¹ NaCl were also calculated and the values are 1.5 μg l⁻¹, 5.0 μg l⁻¹ and 5.0% (at 10 μg l⁻¹ level), respectively.     

Flow injection analysis of ultratrace orthophosphate in seawater with solid-phase enrichment and luminol chemiluminescence detection

Solid-phase extraction technique had been applied to extract molybdophosphoric heteropoly acid (MoP) paired with cetyltrimethylammonium bromide (CTAB) from seawater matrix using C18 sorbent. Chemiluminescence emission could be generated via MoP reaction with alkaline luminol. Based on these, a novel on-line solid-phase extraction method coupled with flow injection (FI) analysis and luminol chemiluminescence detection had been established to determine ultratrace orthophosphate in seawater. The MoP-CTAB compound could be efficiently extracted on an in-line Sep-Pak C18 cartridge, and rapidly eluted by 0.3 mol l⁻¹ sulphuric acid-ethanol solution. Then the compound was reduced by luminol to produce chemiluminescence light, which could be detected using a luminescence analyzer. Experimental parameters were optimized using a univariate experimental design. Using artificial seawater with salinity of 35 as a matrix, the standard curve with a linear range between 0.005 and 0.194 μmol l⁻¹ had been obtained, and the recovery and the detection limit of the proposed method were found to be 92.5% and 0.002 μmol l⁻¹, respectively. The relative standard deviation (R.S.D.), which was determined over eight hour, was 4.66% (n = 7) for the artificial seawater at a concentration of 0.097 μmol l⁻¹ orthophosphate. Si of 200 μmol l⁻¹ would not interfere with the detection of 0.012 μmol l⁻¹ orthophosphate compound. Three typical seawater samples were analyzed using both the proposed method and the magnesium hydroxide-induced coprecipitation (MAGIC) method, and the results of the two methods showed no significant difference using the t test. Compared to the MAGIC method, the proposed method was more sensitive, time saving and easy for on-line analysis.     

Sensitivity enhancement of SPR biosensor with silver mirror reaction on the Ag/Au film

Based on well-known silver mirror reaction the Ag film was formed on Au film modified by self-assembled monolayer (SAM) of 1,6-hexanedithiol (HDT). The sensitivity of the biosensor based on this Ag/Au film is enhanced compared to that based on Au film. When the surface plasmon resonance (SPR) biosensor based on this Ag/Au film was used to determine human IgG, the range of concentrations of human IgG that could be determined is 0.30-40.00 μg mL⁻¹. The lowest concentration (0.30 μg mL⁻¹) that could be detected was about 8 times lower than that obtained by the biosensor without modification by Ag film (2.50 μg mL⁻¹), which demonstrated that the biosensor based on Ag/Au film could make the resonant wavelength move to longer wavelength following with the sensitivity enhancement of the SPR biosensor.     

New microdialysis-electrochemical device for simultaneous determination of ascorbic acid and 5-hydroxyindole-3-acetic acid in rat striatum

A new device combining microdialysis with electrochemical microsensor was developed. It can be applied to monitor the biomolecules in the brain for biological and pharmaceutical research. In this paper, the device was applied to simultaneously determine ascorbic acid (AA) and 5-hydroxyindole-3-acetic acid (5-HIAA) in rat striatum. The microsensor used for the device was poly (sulphosalicylic acid) microsensor, which exhibited a good electrocatalytic effect on oxidization of AA and 5-HIAA. The oxidation currents measured by differential pulse voltammetry (DPV) were linear for AA in the range of 0.02-1.0 mmol l⁻¹, and for 5-HIAA from 0.5 to 10.0 μmol l⁻¹ (r=0.9998 and 0.9991, respectively). The detection limits were calculated to be 0.01 mmol l⁻¹ for AA and 0.25 μmol l⁻¹for 5-HIAA (S/N=3). Studies also showed that co-existing substances in biological fluids did not interfere with AA and 5-HIAA determination when using this microsensor. Since, the substances in the microdialysate are easily oxidized by air, the microdialysate in this device was under the protection of N₂. It was found that the concentrations of AA and 5-HIAA in rat striatum were 215±5 and 6.21±0.61 μmol l⁻¹ (mean±S.E.M., n=7), respectively with this device under the protection of N₂. In addition, the effect of the nitric oxide donor, sodium nitroprusside (SNP), on 5-HIAA in the rat striatum was investigated. It was found that a high concentration of SNP (1.0 mmol l⁻¹) resulted in a 34% increase in 5-HIAA level.     

Direct determination of vanadium in high saline produced waters from offshore petroleum exploration by electrothermal atomic absorption spectrometry

The present work reports the development of a methodology for the direct determination of vanadium in high saline waters derived from offshore petroleum exploration employing electrothermal atomic absorption spectrometry. Such waters, usually called produced waters, present complex composition containing various organic and inorganic substances. In order to attain best conditions (highest sensitivity besides lowest background) for the methodology, studies about the effects of several variables (evaluation of pyrolysis and atomization temperatures, type of chemical modifier, concentration of modifier and pyrolysis time) and the convenient calibration strategy were performed. Best conditions were reached with the addition of 10 μg of NH₄H₂PO₄ as chemical modifier employing pyrolysis (during 10 s) and atomization temperatures of 1500 and 2700 °C, respectively. Obtained results indicated that, in this kind of sample, vanadium can be determined by standard addition method or employing an external calibration approach with standard solutions prepared in 0.8 mol l⁻¹ NaCl medium. In order to evaluate possible matrix interferences, a recovery test was performed with five spiked samples of produced waters. The limit of detection, limit of quantification and relative standard deviation in 0.8 mol l⁻¹ NaCl medium were also calculated and the derived values were 1.9 μg l⁻¹, 6.3 μg l⁻¹ and 5.6% (at 10 μg l⁻¹ level), respectively.     

Silver overlayer-modified surface-enhanced Raman scattering-active gold substrates for potential applications in trace detection of biochemical species

Because Ag and Au nanoparticles (NPs) possess well-defined localized surface plasmon resonance (LSPR) they are popularly employed in the studies of surface-enhanced Raman scattering (SERS). As shown in the literature and in our previous studies, the advantage of SERS-active Ag NPs is their higher SERS enhancement over Au NPs. On the other hand, the disadvantage of SERS-active Ag NPs compared to Au NPs is their serious decay of SERS enhancement in ambient laboratory air. In this work, we develop a new strategy for preparing highly SERS-active Ag NPs deposited on a roughened Au substrate. This strategy is derived from the modification of electrochemical underpotential deposition (UPD) of metals. The coverage of Ag NPs on the roughened Au substrate can be as high as 0.95. Experimental results indicate that the SERS of Rhodamine 6G (R6G) observed on this developed substrate exhibits a higher intensity by ca. 50-fold of magnitude, as compared with that of R6G observed on the substrate without the deposition of Ag NPs. The limit of detection (LOD) for R6G measured on this substrate is markedly reduced to 2 × 10⁻¹⁵ M. Moreover, aging of SERS effect observed on this developed substrate is significantly depressed, as compared with that observed on a generally prepared SERS-active Ag substrate. These aging tests were performed in an atmosphere of 50% relative humidity (RH) and 20% (v/v) O₂ at 30 °C for 60 day. Also, the developed SERS-active substrate enables it practically applicable in the trace detection of monosodium urate (MSU)-containing solution in gouty arthritis without a further purification process.     

Plasmon-Enhanced Electrochemiluminescence at the Single-Nanoparticle Level

Plasmon-enhanced electrochemiluminescence (ECL) at the single-nanoparticle (NP) level was investigated by ECL microscopy. The Au NPs were assembled into an ordered array, providing a high-throughput platform that can easily locate each NP in sequential characterizations. A strong dependence of ECL intensity on Au NP configurations was observed. We demonstrate for the first time that at the single-particle level, the ECL of Ru(bpy)₃²⁺-TPrA was majorly quenched by small Au NPs (<40 nm), while enhanced by large Au ones (>80 nm) due to the localized surface plasmon resonance (LSPR). Notably, the ECL intensity was further increased by the coupling effect of neighboring Au NPs. Finite Difference Time Domain (FDTD) simulations conformed well with the experimental results. This plasmon enhanced ECL microscopy for arrayed single NPs provides a reliable tool for screening electrocatalytic activity at a single particle.     

Dual fluorescence/contactless conductivity detection for microfluidic chip

A new dual detection system for microchip is reported. Both fluorescence detector (FD) and contactless conductivity detector (CCD) were combined together and integrated on a microfluidic chip. They shared a common detection position and responded simultaneously. A blue light-emitting diode was used as excitation source and a small planar photodiode was used to collect the emitted fluorescence in fluorescence detection, which made the device more compact and portable. The coupling of the fluorescence and contactless conductivity modes at the same position of a single separation channel enhanced the detection characterization of sample and offered simultaneous detection information of both fluorescent and charged specimen. The detection conditions of the system were optimized. K⁺, Na⁺, fluorescein sodium, fluorescein isothiocyanate (FITC) and FITC-labeled amino acids were used to evaluate the performance of the dual detection system. The limits of detection (LOD) of FD for fluorescein Na⁺, FITC, FITC-labeled arginine (Arg), glycine (Gly) and phenylalanine (Phe) were 0.02 μmol L⁻¹, 0.05 μmol L⁻¹, 0.16 μmol L⁻¹, 0.15 μmol L⁻¹, 0.12 μmol L⁻¹ respectively, and the limits of detection (LOD) of CCD achieved 0.58 μmol L⁻¹ and 0.39 μmol L⁻¹ for K⁺ and Na⁺ respectively.