Surface treatment of CFRP composites using femtosecond laser radiation

In the present work, we investigate the surface treatment of carbon fiber-reinforced polymer (CFRP) composites by laser ablation with femtosecond laser radiation. For this purpose, unidirectional carbon fiber-reinforced epoxy matrix composites were treated with femtosecond laser pulses of 1024 nm wavelength and 550 fs duration. Laser tracks were inscribed on the material surface using pulse energies and scanning speeds in the range 0.1–0.5 mJ and 0.1–5 mm/s, respectively. The morphology of the laser treated surfaces was investigated by field emission scanning electron microscopy. We show that, by using the appropriate processing parameters, a selective removal of the epoxy resin can be achieved, leaving the carbon fibers exposed. In addition, sub-micron laser induced periodic surface structures (LIPSS) are created on the carbon fibers surface, which may be potentially beneficial for the improvement of the fiber to matrix adhesion in adhesive bonds between CFRP parts.     

Luminescence and micro-Raman investigations on inclusions of unusual habit in chrysoprase from Turkey

Chemical analyses performed on chrysoprase from Turkey have shown many trace elements as well as rare earth impurities. Quantitative chemical analyses of inclusions in minerals can improve our understanding of the chemistry of surface. The environmental scanning electron microscope (ESEM) with an attached X-ray energy dispersive system (EDS) is capable of producing rapid and accurate major element chemical analyses of individual inclusions in crystals larger than about 30 μm in diameter. The samples were examined with lifetime-resolved and spatially-resolved cathodoluminescence (CL), and inductively coupled plasma-atomic emission spectrometry (ICP-AES). Spatially resolved CL results at room temperature were recorded for two different areas. Bulk area displays with low CL emission and pores contain iron phases such as chromite, hematite and anatase which cause the green color. For the raw data in the lifetime resolved CL spectrum, at least three broad emission bands were detected in a yellow band of the highest intensity at about 550 nm, a weaker orange band at about 650 nm, and a red band at 720 nm. It is assumed that there are links between the CL emissions and the presence of some transition metal and REE elements, but it is obvious that all trace elements do not play a direct role. Micro-Raman measurements were performed on chrysoprase and these showed a characteristic intensive Raman band peaked at 464 cm^?1 which can be inferred to ν₂ doubly symmetric bending mode of [SiO₄/M] centers. Raman spectrum of all inclusions found in the material are also given and discussed in detail.     

Comparative study on structural and optical properties of ZnO thin films prepared by PLD using ZnO powder target and ceramic target

Zinc oxide thin films have been obtained in O₂ ambient at a pressure of 1.3 Pa by pulsed laser deposition (PLD) using ZnO powder target and ceramic target. The effect of temperature on structural and optical properties of ZnO thin films was investigated systematically by XRD, SEM, FTIR and PL spectra. The results show that the best structural and optical properties can be achieved for ZnO thin film fabricated at 700 °C using powder target and at 400 °C using ceramic target, respectively. The PL spectrum reveals that the efficiency of UV emission of ZnO thin film fabricated by using powder target is low, and the defect emission of ZnO thin film derived from Zn_i and O_i is high.     

Field electron emission from amorphous carbon thin films grown by RF magnetron sputtering

Using a RF magnetron sputtering, amorphous carbon (a-C) and N-doped a-C (a-C:N) thin films were fabricated as field electron emitter. These thin films were deposited on Si(0 0 1) substrate at several temperatures. The field emission property was improved for a-C thin films grown at higher substrate temperatures. Furthermore, a-C:N film exhibits field emission property better than that of undoped a-C film. These results are explained in terms of the change in surface morphology and structural properties of a-C film.     

Micro-machining of silicon wafer in air and under water

Laser ablation micro-machining tests are conducted on silicon wafer, both in air and under flowing water stream, with the use of 355 nm-X AVIA laser. Effects of laser pulse frequency, power level, scan velocity and focal plane position on the associated laser spatter deposition (in air), irradiated areas (under flowing water film) and taper are investigated. It shows that low frequency, i.e. 30–40 kHz, and high peak power result in smaller spatter and irradiated areas, and the hole taper decreases with increase in pulse frequency. Increase in the laser fluence broadens both the areas and increases the hole taper. Both areas enlarge with the increase of scanning velocity of more than 3 mm s^?1. The scan velocity has no effect on hole taper in air environment but inconsistent hole taper is obtained under flowing water stream. Furthermore, moving the focal plane position below the workpiece surface contributes relatively smaller areas of spatter deposition, irradiation and taper in comparison to zero focal plane position. Finally, the differences between laser ablation in air and under water are identified. The reduction in the spatter deposition and irradiated areas around the perimeter of the ablated hole and a smaller taper with the use of laser trepan drilling method in air and under water machining are investigated in this paper.     

High intensity photoluminescence of microcrystalline CsPbBr3 films: Evidence for enhanced stimulated emission at room temperature

Photoluminescence of microcrystalline CsPbBr₃ films grown from the amorphous phase shows stimulated emission not only at cryogenic temperature but also at room temperature, in great contrast to the case for bulk CsPbBr₃ single crystals, where no stimulated emission occurs even at 4.2 K. This is the first demonstration of room temperature stimulated emission from metal halide compounds.The stimulated emission is so strong that single-path-light-amplification stimulated emission across the film thickness is observed at relatively low threshold excitation intensities of ∼50 kW cm⁻² at 77 K and ∼100 kW cm⁻² at 295 K suggesting a large optical gain. The physical origin of the stimulated emission is assigned as due to free exciton-free exciton inelastic collision. The large-gain mechanism is attributable to giant oscillator strength effect characteristic of excitonic superradiance recently reported in this issue.     

Surface characterization of imidazolium ionic liquids by high-resolution Rutherford backscattering spectroscopy and X-ray photoelectron spectroscopy

The surface composition of 1-butyl-3-methylimidazolium hexafluorophosphate ([BMIM] [PF₆]) and 1-butyl-3-methylimidazolium dicyanamide ([BMIM] [DCA]) are studied by high-resolution Rutherford backscattering spectroscopy. Although [BMIM] [PF₆] is almost stoichiometric up to the topmost molecular layer, considerable deviation from the theoretical stoichiometry is observed for [BMIM] [DCA] in a surface layer of ～1.5 nm thickness. Nitrogen is almost completely depleted in this layer while carbon is enhanced. In addition, there are oxygen impurities of ～3 × 10¹⁴ atoms/cm² in this surface layer. With the help of X-ray photoelectron spectroscopy measurements it is concluded that the surface of [BMIM] [DCA] is covered by ～1.7 × 10¹⁴ molecules/cm² of esters and/or carboxylic acids. These contaminant molecules have a preferred orientation, i.e. the carbonyl groups are on the surface of [BMIM] [DCA] and the alkyl chains are pointing towards vacuum. The origin of the contamination layer could be the surface segregation of bulk impurities.     

STM light emission from Si(1 1 1)-(7 × 7) surface using a silver tip

Scanning tunneling microscope-light emission (STM-LE) from the Si(1 1 1)-(7×7) surface has been measured using silver tips. For silver tips photon emission was enhanced by more than 100 times as compared with that for tungsten or platinum–iridium alloy tips. A broad spectrum with a single peak at ∼2.25 eV was observed. The spectrum obtained can be reproduced by a theory based on the macroscopic dielectric response of the tip-sample system, indicating that the observed emission arises from the localized plasmons on the silver tip excited by tunneling electrons. Spatial variations in the emission intensity at the atomic scale was observed even under low bias voltage (2 V) and low tunneling current (1 nA) conditions.     

Ultrasound treated potato peel and sweet lime pomace based biopolymer film development

Treatment and management of food processing waste is a major challenge for food industry. Potato processing industry generates tremendous amount of peel and consider it as zero valued waste. Again, pomace generated after juice extraction from sweet lime pulp is considered as waste and not properly utilized. Whereas these waste could be utilized for the development of biodegradable packaging film to overcome environmental issues. Composite films were prepared with varying proportion of potato peel powder (PP) and sweet lime pomace (SLP) in the ratio of 0:1(A), 0.5:1(B), 1:1(C), 1:0.5(D), 1:0(E) with an ultrasound treatment of 45 min, and 0:1(F), 0.5:1(G), 1:1(H), 1:0.5(I), 1:0(J) with an ultrasound treatment of 60 min. Ultrasound was applied for 45 and 60 min to film forming solutions to break down biopolymer particles small enough to form a film. All the films were analyzed for their barrier and mechanical properties. It was observed that increasing ultrasound treatment times gives better result in film properties and less PP content also gives better film properties, from these observations film G prepared with 0.5:1 (PP:SLP) showed better characteristics among all other films. Water vapor permeability, moisture absorption, water solubility, breakage strength and elongation capacity of G film were reported as 7.25 × 10⁻⁹ g/Pa h m, 12.88 ± 0.348%, 38.92 ± 0.702%, 242.01 ± 3.074 g and 7.61 ± 0.824 mm respectively. However, thermal decomposition for film G took place above 200 °C. The film forming solution of selected G film, added with clove essential oil (1.5%) as an antimicrobial agent was wrapped on bread and stored it for 5 days. The film was successful in lowering the weight loss, reducing the hardness and inhibition of surface microbial load from bread sample.     

Influence of argon ambience on the structural,morphological and optical properties of pulsed laser ablated zinc sulfide thin films

Nanostructured zinc suplhide thin films are successfully deposited on quartz substrates using pulsed laser deposition (PLD) under different argon pressures (0, 5, 10, 15 and 20 Pa). The influence of argon ambience on the microstructural, optical and luminescence properties of zinc sulfide (ZnS) thin films is systematically investigated. The GIXRD data suggests rhombohedral structure for ZnS films prepared under different argon ambience. Self-assembly of grains into well-defined patterns along the y direction is observed in the AFM image of the film deposited under argon pressure 20 Pa. All the films show a blue shift in optical band gap. This can be due to the quantum confinement effect and less widening of conduction and valence band for the films with less thickness and smaller grain size. The PL spectra of the different films are recorded at excitation wavelengths 250 nm and 325 nm and the spectra are interpreted. The PL spectra of the films recorded at excitation wavelength 325 nm show intense yellow emission. The film deposited under an argon pressure of 15 Pa shows the highest PL intensity for excitation wavelength 325 nm. For the PL spectra (excitation at 250 nm), the highest PL intensity is observed for the film prepared under argon free ambience. In our study, 15 Pa is the optimum argon pressure for better crystallinity and intense yellow emission when excited at 325 nm.     

Influence of heat treatment on field emission characteristics of boron nitride thin films

Boron nitride (BN) nanometer thin films are synthesized on Si (1 0 0) substrates by RF reactive magnetron sputtering. Then the film surfaces are treated in the case of the base pressure below 5 × 10⁻⁴ Pa and the temperature of 800 and 1000 °C, respectively. And the films are studied by Fourier transform infrared spectra (FTIR), atomic force microscopic (AFM) and field emission characteristics at different annealing temperature. The results show that the surface heat treatment makes no apparent influence on the surface morphology of the BN films. The transformations of the sample emission characteristics have to do with the surface negative electron affinity (NEA) of the films possibly. The threshold electric fields are lower for BN samples without heat-treating than the treated films, which possibly ascribed to the surface negative electron affinity effect. A threshold field of 8 V/μm and the emission current of 80 μA are obtained. The surface NEA is still presence at the heat treatment temperature of 800 °C and disappeared at temperature of 1000 °C.     

Comprehensive electro-optical analysis of long wavelength GaInNAs edge-emitting laser diode

Comprehensive analysis of GaInNAs edge-emitting laser operating near 1300 nm wavelength are made to underline the behavioural features of the proposed laser device, in view of the analytical investigation for various material and device electrical-optical parameters analysis such as band diagram, material gain, quantum well emission wavelength, optical wave and mode profiles, light-current-voltage characteristic, output mode spectrum, current distribution and far-field profile. The material analysis indicates that a high quality GaInNAs active region is designed, where high material gain and photoluminescence wavelength near 1.3 μm are achieved. The device obtains low threshold current operation with lasing emission around 1.285 μm.     

Master Oscillator-Power Amplifier carbon monoxide laser system emitting nanosecond pulses

To increase a peak power of carbon monoxide laser emitting nanosecond pulses a Master Oscillator-Power Amplifier (MOPA) laser system was developed. The MOPA CO-laser system employed one and the same gain medium of wide-aperture pulsed electron-beam-sustained-discharge CO-laser facility. Amplification parameters include gain and saturation intensity of amplifying media. The MOPA CO-laser system emitted a train of nanosecond pulses with peak power up to ~ 0.1 MW on a single spectral line and up to ~ 0.4 MW with multiline spectrum.     

Low-cost micro-lens arrays fabricated by photosensitive sol–gel and multi-beam laser interference

In this paper, we introduce a low-cost approach for fabricating micro-lens arrays that is based on photosensitive sol–gel and multi-beam laser interference. UV photosensitive ZrO₂ gel films are prepared with Zr(O(CH₂)₃CH₃)₄ and BzAcH as the precursor and chemical modifier, respectively. With UV laser irradiation via different dose, nonlinear photodecomposition occurs in this film. Large scale 2D micro lens arrays with the sizes of 830 nm × 830 nm and 280 nm × 280 nm are fabricated by four-beam laser interference. The surface profile modeling shows that the micro lens is plano convex lens, and the effective focal lengths are 812.0 nm and 317.6 nm, respectively.     

Nanocrystalline SnO2–TiO2 thin film deposited on base of equilateral prism as an opto-electronic humidity sensor

Present paper reports the synthesis of SnO₂–TiO₂ nanocomposite, its characterization and performance as opto-electronic humidity sensor. Nanocrystalline SnO₂–TiO₂ film was deposited on the base of an equilateral prism using a photo resist spinner and the as prepared film was annealed at 200 °C for 2 h. The crystal structure of the prepared film was investigated using X-ray diffraction (XRD). Minimum crystallite size of the material was found 7 nm. Surface morphology of the film was investigated by Scanning electron microscope (SEM LEO-0430, Cambridge). SEM image shows that the film is porous. Differential scanning calorimetry (DSC) of as synthesized material shows two exothermic peaks at about 40 and 110 °C, respectively which are due to the evaporation of chemical impurities and water. Further the prepared film was investigated through the exposure of humidity and relative humidity (%RH) was measured directly in terms of modulation in the intensity of light recorded on a digital power meter. The maximum sensitivity of sensor was found 4.14 μW/%RH, which is quite significant for sensor fabrication purposes.     

Electron-energy-loss spectroscopy of C60 monolayer films on active and inactive surfaces

The characteristics of interaction between C₆₀ molecules and Si(1 1 1)-7×7, Ag/Si(1 1 1)-√3×√3 R30° and layered material MoS₂ surfaces have been investigated using electron-energy-loss spectroscopy (EELS). The EEL spectrum of C₆₀/Si(1 1 1)-7×7 shows a new peak at loss energy of 2.7 eV. This indicates the existence of charge transfer from the substrate to C₆₀ molecules. The EEL spectrum of a C₆₀ monolayer film grown on a cleaved surface of MoS₂ is almost the same as that of bulk C₆₀. The EEL spectrum of a C₆₀ monolayer film on an Ag/Si(1 1 1) surface is quite different from that on a clean Si(1 1 1)-7×7 surface, although the films on those substrates have the same epitaxial arrangement. Furthermore, intensities of energy-loss peaks of C₆₀/Ag/Si(1 1 1) are slightly smaller than those of C₆₀/MoS₂ in spite of having the same loss-energy. This suggests that the interaction between C₆₀ molecules and the Ag/Si(1 1 1) surface is stronger than that between C₆₀ molecules and the MoS₂ surface.     

Broadband 2.84 μm luminescence properties and Judd–Ofelt analysis in Dy3+ doped ZrF4–BaF2–LaF3–AlF3–YF3 glass

2.84 μm luminescence with a bandwidth of 213 nm is obtained in Dy³⁺ doped (ZrF₄–BaF₂–LaF₃–AlF₃–YF₃) ZBLAY glass. Three intensity parameters and radiative properties have been determined from the absorption spectrum based on the Judd–Ofelt theory. The 2.84 μm emission characteristics and energy transfer mechanism upon excitation of a conventional 808 nm laser diode are investigated. The prepared Dy³⁺ doped ZBLAY glass possessing high predicted spontaneous transition probability (45.92 s^?1) along with large calculated emission cross section (1.17×10^?20 cm²) has potential applications in 2.8 μm laser.     

Characterization of luminescent chromophore obtained from silica spheres

Blue light emitting chromophores have been separated from silica spheres by soaking them into acetone for 120 days. The luminescent chromophores were not obtained from other solvents, including ether, methanol, ethanol, 2-propanol, chloroform and tetrahydrofuran. According to the Fourier transform infrared spectrum, the luminescent material is composed of C–OH, –CH₂, –CH₃, C=O, and Si–O–Si. UV–visible absorption peak of the chromophore is at 5.17 eV (240 nm). Field emission scanning electron microscope images show small cracks on the surface of aged spheres. The luminescence peak was at 2.81 eV (441 nm) for excitation energy between 3.88 and 3.35 eV and slightly shifted toward lower energy for excitation energy lower than 3.35 eV. The deconvoluted luminescent spectrum shows two emission bands at 3.08 and 2.74 eV, which are well-matched the oxygen deficient center model. Compared to the absorption peak (5.17 eV) and the emission peak (2.81 eV), large Stokes shift (2.36 eV) is observed.     

Microstructures and nano mechanical properties of the metal tungsten film

The W film was prepared on 1045 steel by magnetron sputtering, with the thickness of 2 μm, its surface and cross-section morphologies were investigated with SEM, and the phase structure was analyzed with XRD. X-ray stress determinator was utilized to measure its residual stress, and the nano-hardness and elastic modulus of the film were surveyed by nano-indentation tester. The results show that the surface of W film is very compact and smooth; the particles arranged regularly, the granularity of the thin film is about 1 μm. The microcracks, cavities and desquamation were not found in the film and interface, and the bonding between the W film and substrate is well. The XRD results showed that the W film had a body-centered cubic structure, the lattice constant: a = 0.316 nm, the growth preferred orientations are (1 1 0) and (2 2 0). The compressive stress (−169 MPa) was found on the surface. The average nano-hardness and elastic modulus of W film are 15.22 GPa, 176.64 GPa, respectively, and the mechanical properties of W film are well.     

Efficient treatment of pigmented B16 melanoma using photosensitized long-circulating magnetofullerenosomes

Magnetic targeting was used for melanoma treatment with magnetofullerenosomes. After their intravenous administration, a permanent magnet was attached to the surface of B16 tumors in C57 mice for 24 h, followed by irradiation with an infrared laser pulse and subsequent illumination with a 776 nm diode laser for conventional photodynamic treatment. Tumor response was substantially better than that obtained with either treatment alone.