通过正离子聚合原位制备聚谷氨酸苄酯-g-(聚四氢呋喃-b- 聚异丁烯)/银纳米复合材料及其性能研究

采用烯丙基溴官能化聚异丁烯/高氯酸银体系引发四氢呋喃活性正离子聚合制备聚谷氨酸苄酯-g-(聚四氢呋喃-b-聚异丁烯)/银纳米复合材料(PBLG-g-(PTHF-b-PIB)/Ag).研究接枝密度对该纳米复合材料表面组成、形貌及自组装行为的影响,进一步探究纳米复合材料中银的含量、分布、晶型及存在形态,以布洛芬(IBU)作为模拟药物,研究接枝共聚物中接枝密度和平均支链长度对纳米复合材料载药释药行为的影响,通过抑菌圈法和MTT法研究纳米复合材料的抗菌性和细胞毒性.结果表明:通过烯丙基溴官能化聚异丁烯大分子引发四氢呋喃活性正离子开环聚合,可以原位制备不同接枝密度和不同平均支链长度的PBLG-g-(PTHF-b-PIB)/Ag纳米复合材料,其中银的质量含量在0.25%~3.9%之间,与其理论含量基本相吻合,银颗粒以聚集体形态存在,尺寸为5~10 nm,晶型为面心立方结构;该纳米复合材料在四氢呋喃/正己烷(4/1,V/V)混合介质中自组装形成胶束,胶束数目随接枝密度增加而减少,但尺寸增大;随接枝共聚物中接枝密度和纳米银含量增加,纳米复合材料的疏水性增加;随接枝共聚物中接枝密度增加,纳米复合材料表面形貌可由球形结构逐渐转化为双连续相结构;纳米复合材料的载药微球可以通过接枝共聚物中主链PBLG的空心螺旋结构、酰胺键及PTHF支链的醚键结构显示三重载药特性,载药量和累积释药量均随着接枝共聚物中接枝密度或PTHF链段长度增加而增加,且在37oC下的释药率是25oC下释药率的3倍左右.该纳米复合材料的抗菌性能随纳米银含量增加而增加,当纳米银含量为1.48%时,该纳米复合材料1周后细胞存活率为97.7%,即无细胞毒性.     

聚谷氨酸苄酯-g-(聚四氢呋喃-b-聚异丁烯)共聚物的微观结构与形态

通过可控/活性离子聚合方法设计合成一系列不同共聚组成的聚谷氨酸苄酯-g-(聚四氢呋喃-b-聚异丁烯)的新型嵌段接枝共聚物,即PBLG-g-(PTHF-b-PIB),研究共聚物中支链(PTHF-b-PIB)长度及接枝密度对主链PBLG玻璃化转变温度、α-螺旋二级结构及其转变的影响,研究支链中PTHF链段长度对其双端受限的玻璃化转变及凝聚态结构的影响.结果表明:PBLG-g-(PTHF-b-PIB)共聚物中刚性主链保持α-螺旋二级结构;随着支链长度增加或接枝密度增加,主链PBLG的α-螺旋二级结构特征峰逐渐减弱,玻璃化转变温度逐渐提高,α-螺旋结构发生转变的焓值逐渐增大;在确定接枝密度的情况下,随着支链中PTHF链段长度增加,共聚物中双端受限的PTHF链段结晶逐渐增强,结晶熔融温度及熔融焓均增加;在确定支链中PTHF链段长度的情况下,随着接枝密度增大,支链间链段相互排斥,PTHF链段结晶逐渐减弱.     

活性正离子聚合及原位制备聚醋酸乙烯酯-g-聚四氢呋喃共聚物/纳米银复合材料

通过将烯丙基溴/高氯酸银引发体系引发四氢呋喃活性正离子开环聚合与"grafting onto"合成方法相结合,原位制备了不同接枝密度和接枝链长度的新型聚醋酸乙烯酯-g-聚四氢呋喃接枝共聚物(PVAc-g-PTHF)及其与纳米银(Ag)的复合材料.采用傅里叶变换红外光谱(FTIR)、核磁共振波谱(1H-NMR)和多角度激光光散射-黏度-凝胶渗透色谱仪(MALLS-VIS-GPC)分别表征了该接枝共聚物的化学结构、共聚组成、分子量、分子量分布、接枝支链数目及支化度,采用原子力显微镜(AFM)、示差扫描量热分析(DSC)、偏光显微镜(POM)研究了接枝共聚物中接枝支链数目及支链长度对其微观形态、单端受限链段结晶行为的影响,并探讨了该纳米复合材料的抗菌性能.结果表明:所制备的不同支链数目和支链长度的PVAc-g-PTHF/Ag纳米复合材料,均表现出良好的抗菌性能;接枝共聚物PVAc-g-PTHF的重均分子量可达4.52×10~5,分子分子量较窄(M_w/M_n~1.8),支化因子可达0.19.接枝共聚物PVAc-g-PTHF可形成明显的相分离结构,其微观形态与接枝支链数目有关;相比相同分子量的双端不受限的PTHF链,PVAc-g-PTHF接枝共聚物中单端受限PTHF支链的结晶速率明显降低;在确定接枝支链数目的情况下,随着支链中PTHF链段长度增加,其结晶逐渐增强,结晶熔融温度及熔融焓均稍有增加.     

含双键侧基的聚氧乙烯与苯乙烯的接枝共聚物及其产物的性质

由环氧乙烷及烯丙基缩水甘油醚合成含双键侧基的聚氧乙烯用苯乙烯接枝共聚,接枝效率可达50％左右.接枝产物经纯化,用IR及~1H NMR表征.该产物与LiClO_4的络合物有较高的室温导电率,其PEO含量在70％及EO/Li=20/1时,25℃的导电率接近10~(-4)S/cm.此外,该接枝共聚物有较高的乳化能力.在Williamson固液反应中具有良好的相转移催化作用.     

聚甲基丙烯酸β羟乙酯在聚乙烯膜上辐射接枝物的形态结构

本文用透射电子显微镜(TEM),光学显微镜(OM),小角X射线散射(SAXS)等方法研究了聚甲基丙烯酸β羟乙酯(HEMA)在聚乙烯(PE)膜上辐射接枝物的形态结构.观察了微相结构随接枝条件变化规律.HEMA为支链的接枝共聚物的基本形态是高度分散的HEMA微区(约几百A)存在于PE连续相中的两相体系.随接枝量增加,微区形态发生变化.SAXS结果进一步证实了接枝共聚物相分离的形态结构,并利用Tsvankin-Buchanan公式计算了共聚物的长周期、无定形层厚及一维结晶度.     

结晶-非晶共混体系的结晶行为研究——PEO/PMMA与PEO/PVA共混物

用DSC和傅里叶红外(FTIR)光谱表征PEO/PMMA和PEO/PVA共混体系的结晶行为。发现PEO/PVA体系的结晶度与其组成的变化是一致的;而PEO/PMMA体系的结晶度随非晶组分增加而下降的速度,从与组成变化一致到比后者快,但又随时间而改变。对此结晶/非晶共混体系的结晶度随组成和时间而变化的现象,可用体系的玻璃化转变温度(T_g)来解释。     

结构可控的聚合物长短刷接枝纳米粒子

通过RAFT聚合制备了一系列窄分子量分布的聚(γ-甲基丙烯酰氧基丙基三乙氧基硅烷)(PTEPM)-b-聚甲基丙烯酸甲酯(PMMA)嵌段共聚物和PTEPM、PMMA低聚物.将具有不同PMMA分子量的2种PTEPM-b-PMMA共聚物与低聚物PMMA或PTEPM进行共组装(微相分离),形成片、柱、球等不同PTEPM相区结构.采用盐酸气氛处理,PTEPM相区水解交联形成倍半硅氧烷SiO1.5内核,分离纯化得到聚合物长短刷接枝纳米粒子.使用这种相分离-交联-分散制备方法,调节嵌段共聚物分子结构和三组分比例,可实现聚合物接枝纳米粒子内核形状和尺寸、接枝密度、长短刷比例、长刷长度的精确调控.这些纳米粒子是研究聚合物纳米复合材料结构-性能关系的理想模型体系.     

SEOS/h-PEO共混物薄膜的微观分相结构

采用透射电子显微镜(TEM)观察由结晶性均聚物聚氧乙烯(h-PEO)与半结晶性嵌段共聚物聚苯乙烯-嵌-聚氧乙烯-嵌-聚苯乙烯(SEOS)组成的干、湿刷共混物薄膜结构.结果表明:4种共混系统的薄膜结构均由嵌段PEO和PEO均聚物组成球形PEO分散相;随着均聚物含量的增加,PEO分散相尺寸逐渐增大;当均聚物质量分数增大到33.3%时,在聚苯乙烯(PS)连续相中形成了类似胶束的"核-壳"结构.     

聚硅氧烷-聚醚接枝共聚物的合成及其碱金属盐络合物离子电导的研究

 本文采用环氧乙烷与环氧丙烷共聚合成了一系列低分子量的聚醚(PEP),并用PEP的单烯丙基醚借助氢化硅烷基化反应(Hydrosilylation)制备出一种新型聚硅氧烷接枝聚醚的高分子电解质主体材料(PAEPS).分别讨论了共聚物组成、盐的种类和浓度等因素对交联PAEPS与碱金属盐络合物电解质膜离子电导的影响.结果表明,PAEPS与碱金属盐络合物的室温电导率较纯线型PEO提高两至三个数量级,电导率随温度变化关系基本上符合VTF方程,属于典型的非晶电解质行为.     

含三价铕荧光络合物与聚甲基丙烯酸甲酯的发光材料

用荧光性能优异的Eu(TTA) 3 ·2TPPO络合物与聚甲基丙烯酸甲酯 (PMMA)制备了一系列发出红色荧光的光致发光材料 .荧光测定结果表明 :PMMA膜的荧光强度随膜中络合物含量的增加而增大 .红外光谱研究表明络合物与PMMA之间存在相互作用 .透射电镜观测结果表明络合物在复合膜中是以亚微米颗粒分散的 .     

On the macro- and microphase separation of compatibilizers in immiscible polymer blends

Macro- and microphase separation of compatibilizing graft copolymers in melt-mixed polystyrene/polyamide-6 blends was studied by transmission electron microscopy and thermal analysis. Three different graft copolymers with main chains of polystyrene and side chains of poly(ethylene oxide) were used as additives at various concentrations. The polyamide-6 domain sizes decreased with increasing amounts of compatibilizing graft copolymers in the blends up to a saturation concentration, after which no further reduction was noted. Macrophase separation of the graft copolymers into discrete macrodomains 20–200 nm in size occurred at concentrations equal to or slightly lower than the saturation concentration. The macrodomains of the graft copolymers were microphase separated, and the sizes and shapes of the microdomains were found to largely depend on the graft copolymer structure and composition. As a consequence of microphase separation, poly(ethylene oxide) crystallinity was noted in blends with sufficiently high macrophase contents. Observations of a graft copolymer interphase between the polystyrene matrix and the polyamide-6 domains confirmed that the graft copolymer was present at the blend interfaces in some of the compatibilized blends. © 1996 John Wiley & Sons, Inc.     

乙烯-α-烯烃共聚物的结晶性能及其临界序列结晶长度的研究

本文用DSC、WAXD及偏光显微镜(PLM)方法,研究了化学反应法催化剂合成的乙烯-α-烯烃共聚物的结晶性能及其临界序列结晶长度。结果表明,随共聚物中α-烯烃含量增大,共聚物的微晶尺寸、结晶度及熔点均逐渐减小,而晶胞参数增大。变化的辐度戊烯>辛烯。共聚物的临界结晶序列长度(n)和k值均戊烯<辛烯。上述结果表明影响支链进入晶格的主要因素是α-烯烃支链长度和结构。     

Side-chain crystallinity. II. Heats of fusion and melting transitions on selected copolymers incorporating n-octadecyl acrylate or vinyl stearate

The heats of fusion and the melting transitions of the crystallinity present in the side chains were determined for selected copolymers incorporating n-octadecyl acrylate or vinyl stearate. A major purpose of this investigation was to ascertain the effect of interrupting the long ordered 18-carbon side chains by randomly interspersed amorphous side chains of various lengths. For this purpose the lower acrylate homologs (C₁ through C₈ and including oleyl, C₈) were copolymerized over the composition range with n-octadecyl acrylate. It was found that simple dilution of the crystalline component (from comonomer b) by the amorphous component (from comonomer a) governed the decline in the heats of fusion and the fraction of crystallinity present. High crystallization rates were encountered because equilibrium crystallinity was nearly achieved for most of the copolymers. Melting point depression was less than theory in copolymers having short amorphous comonomer side chain lengths, but approached the theoretical depression as these side chains became very long. Thus the outer methylene sequences (the crystalline sequences) of the fatty co-units could bridge the smaller amorphous a units, giving rise to larger crystal sizes than theory specified. Main-chain stiffness, when present in the melt, had a small effect on the distribution of crystallite sizes but exhibited a much larger influence in preventing the attainment of equilibrium crystallinity, especially at high amorphous comonomer compositions. However, crystallinity was still high compared with that of copolymers described in the literature crystallizing through their main-chain units. When long blocks of crystalline segments were present (as in compositionally heterogeneous vinyl stearate copolymers), melting point depression was small and followed the theoretical probability sequence function.     

Irradiation effects on thermal,surface, and physicomechanical properties of ethylene and vinyl acetate copolymer

The structural and thermal transitions for ethylene and vinyl acetate copolymer (EVA) samples irradiated by fast electrons at doses in the range of 2.5–25 Mrad were investigated by DSC and X-ray diffraction analysis. The parameters of chemical bonds in the amorphous phase of copolymer were determined. The change in the degree of crystallinity, melting temperature, and crystallite sizes before and after radiochemical modification were estimated. The obtained results were analyzed and corresponded to the physicomechanical properties of copolymers. The surface energy of copolymers before and after irradiation was defined. The strength of adhesive joints based on EVA from PET substrates and the influence of radiochemical modification of adhesive before joint formation on its strength were analyzed.     

ABA／PET液晶共聚酯酰胺的结构与性能

研究了对象基苯甲酸（ＡＢＡ）／聚对苯二甲酸乙二酯（ＰＥＴ）液晶共聚酯酰胺的晶体结构，以及热性能、流变学和力学性质。广角Ｘ射线衍射研究结果表明ＡＢＡ链节的引入使ＰＥＴ的晶态结构发生畸变，但大部分结晶衍射峰仍然存在。随着ＡＢＡ含量的增加，各晶面间距基本不变，微晶尺寸显著增大，结晶度急剧降低。差示扫描量热分析和热失重结果表明共聚酯胺具有优良的热稳定性，并且随着ＡＢＡ含量的增加，共聚物的热稳定性提高，共聚     

X-ray investigation of polypropylene and poly(ethylene-co-vinyl acetate) blends irradiated with fast electronsWAXS investigation of irradiated i-PP/EVA blends

Blends consisting of poly(propylene-ethylene) (PP) and poly(ethylene-co-vinyl acetate) (EVA) copolymers were investigated. Specimens were irradiated with fast electrons at different doses. Some of the samples show thermo-shrinkable properties. The interplanar spacing, paracrystalline factor, degree of crystallinity and crystallite sizes were determined by WAXS measurements. Results have been reported in respect to PP content and irradiation dose. A decrease of the crystallite’s imperfections with the rise of the irradiation dose was observed. An interface built up of partially interpenetrated amorphous molecular chains of incompatible polymers and separate PP and EVA small crystallites is suggested.     

Structure and Mechanical Properties of Ethylene-butene Copolymers

IntroductionThe studies on synthesizing ethylene- butenecopolymershavebeen oneofthemostattracting sub-jects[1,2 ] .A novel ethylene- butene copolymer elas-tomer was synthesized from gas phase polymeriza-tion in ourlaboratory in thepresenceofa new highlyactive catalyst Ti Cl4 ,Ti(OBu) 4/ Mg Cl2 ,Si O2 or Zn-Cl2 / alcohol/ Al R3 ,which has the properties ofoligamerization and copolymerization in site to cat-alyze the gas phase polymerization of ethylene andbutene[3 ] .This kind of copolymer…     

以离子液体为介质的纤维素加工与功能化

纤维素作为自然界中储量最大的天然高分子,被认为是未来世界能源与化工的主要原料.但由于分子链间存在丰富氢键网络以及高度结晶的聚集态结构特点,天然纤维素不熔化、难溶解,造成纤维素的加工极其困难,纤维素材料的传统生产工艺复杂且污染严重,极大限制了纤维素材料的广泛应用.近年来,人们发现一些特定结构的离子液体能够高效溶解纤维素,为纤维素的加工和功能化提供了新的多用途平台.本文从"溶解纤维素的离子液体、纤维素溶解机理与溶液性质、以离子液体制备再生纤维素材料和以离子液体为介质合成纤维素衍生物"4个方面详细介绍了本课题组在此领域的研究进展.     

The effect of molecular weight and crystallite structure on yielding in ethylene copolymers

Nominal stress-strain curves of a series of random ethylene-hexene copolymers having narrow composition and most probable molecular weight distributions were investigated. A series of such molecular weight copolymers with a constant concentration of branches were crystallized under a variety of conditions. In each molecular weight series the level of crystallinity was approximately constant. Particular attention was focused on the yield region and the nature of the yielding process. It was found, quite surprisingly, that the yield stress was not solely dependent on the crystallinity level. Moreover, the shape of the force-elongation curve in the yield region was very dependent on the molecular weight and the crystallization mode. These changes in yielding correlated quite well with the overall crystallite structure that was characterized by thin section transmission electron microscopy. The orthorhombic unit cell of polyethylene was maintained in all the samples despite the changes that occurred in the overall crystallite structure. © 1997 John Wiley & Sons, Inc.     

Studies of structure formation in grafting of polyacrylonitrile to polycaproamide fibers

The relationship between the basic structure parameters of a polycaproamide (PCA) substrate and the structure of grafted polyacrylonitrile (PAN) was studied. The influence of the total degree of crystallinity of the PCA fiber, its crystal modification, and the orientation of crystallites on the PAN structure in the copolymer were analyzed. The structure of PCA-PAN graft copolymers was studied by infrared spectroscopy (dichroism and ATR), X-ray structure analysis, nuclear magnetic resonance, and scanning electron microscopy. The development of an oriented isotactic structure was found in PAN grafted to a PCA substrate having a bigh degree of orientation. The type of crystal modification of PCA does not affect the structure formation process in PAN. The oriented structures in PAN arise directly in the course of synthesis rather than on the subsequent rearrangement of the molecular chains under the action of orientation drawing. In contrast to earlier findings, our studies indicate that synthesis under the conditions specified increases the degree of crystallinity of PCA and crystallite size. The grafted PAN chains are presumed to grow epitaxially under the influence of PCA crystallites.