受均布速度作用的有限板面导纳研究

针对接触面积上典型的激励形式,均布速度激励,推导有限薄板上面导纳的理论计算方法。在推导过程中,将接触面积离散为较小的子面积,连续分布的激励和响应简化为作用在子面积中心的激励和响应,再利用有效点导纳的定义,获得有限薄板受均布速度激励的面导纳的理论计算公式;根据接触面积上复功率与面导纳的关系,推导出由传递点导纳获得有限板面导纳的测量方法。通过比较理论计算结果和实验测量结果,证明两种方法可行。对计算结果进行的分析还表明,子面积数的增加可以提高理论计算的精度,而测量精度在激励频率较高时受测量装置产生的弯矩影响较大。      

Investigation of area mobility of a finite thin plate subject to a uniform velocity excitation

Methods for theoretically calculating area mobility of a finite thin plate are derived for a typical excitation pattern,uniform velocity excitation,over a contact area.In the derivation,the contact area is discretised into sub-regions and the excitation and response continuously distributed over these sub-regions are simplified as acting at the centers of the sub-regions.Therefore,according to the concept of effective point mobility,the theoretical formula for area mobility of a finite thin plate subject to a uniform velocity excitation is obtained.According to the relation between complex power and area mobility,the measurement method of a finite plate is also obtained by means of transfer point mobility.When comparing results generated by theoretical calculation to patterns measured in experiment,consistent patterns are found,suggesting that the proposed methods are practical.The results of calculation show that the accuracy of theoretical calculation increases with the number of sub-regions and is influenced by the moment caused by the experiment device,especially when the excitation frequency is high.     

Point and transfer mobility of point-connected ribbed plates

The work reported in this paper addresses the problem of structure-borne sound transmission between vibrating sources and ribbed-plate receiver structures. Vibrating sources, such as pumps, motors, fans, etc., transmit vibro-acoustic power, causing noise complaints by occupants in cars, trains, aircraft, buildings and/or material fatigue and damage. The transmission process is complicated in that sources transmit power through several contacts and by up to six components of excitation at each contact. The structure-borne sound power is a function of source activity, source mobility and receiver mobility, and all three quantities must be known to some degree. For non-homogeneous receiver structures, such as thin-plate cavity constructions or lightweight framed constructions, the sheathing plates are typically fastened to the framing members using bolts, screws or spot-welded joints. Hence the resulting system is a point-connected ribbed plate structure and the receiver mobility is expected to vary significantly with position. Since measured receiver data seldom is available for prediction purposes, a method of estimating the point and transfer mobility of point connected ribbed plates is required. In this paper, an approximate approach, based on substitution forces, is described. The model uses infinite beam and infinite plate behaviour as input quantities. Estimates of point and transfer mobility are compared with measured results using a timber joist floor construction as an example.     

An approximation for the point mobility at the intersection of two perpendicular plates

The problem of point excitation at a T-intersection of two perpendicular plates is studied in order to establish expressions for the point mobility. It is found that the theory for point excitation of the free surface of a semi-infinite elastic solid is applicable in the frequency range associated with structure-borne sound transmission. From this theory the mobility for an infinite system is derived. Based on this model and on an experimental investigation an estimation procedure for the point mobility in the finite dimension case is developed. The agreement with measurements performed in situ is quite acceptable. Both the theoretical and the experimental investigations reveal that the real part of this mobility is small, although it is larger in the experimental results. This indicates that other components of excitation are difficult to eliminate and may contribute to the power input in practice. Because of the small real part of the mobility it is advantageous with respect to the reduction of structure-borne sound power transmission to locate the contact points between a source and the receiver at such intersections. Corrections are deduced for the measured magnitude of the mobility for the case when separate force and motion transducers are used.     

Optimization of fin geometry in heat convection with entransy theory

The entransy theory developed in recent years is used to optimize the aspect ratio of a plate fin in heat convection.Based on a two-dimensional model,the theoretical analysis shows that the minimum thermal resistance defined with the concept of entransy dissipation corresponds to the maximum heat transfer rate when the temperature of the heating surface is fixed.On the other hand,when the heat flux of the heating surface is fixed,the minimum thermal resistance corresponds to the minimum average temperature of the heating surface.The entropy optimization is also given for the heat transfer processes.It is observed that the minimum entropy generation,the minimum entropy generation number,and the minimum revised entropy generation number do not always correspond to the best heat transfer performance.In addition,the influence factors on the optimized aspect ratio of the plate fin are also discussed.The optimized ratio decreases with the enhancement of heat convection,while it increases with fin thermal conductivity increasing.     

Vibrational power flow from machines into built-up structures,part II: Wave propagation and power flow in beam-stiffened plates

Wave propagation and power flow due to force and torque (moment) excitation has been studied at the driving point and in the far field of an infinite plate with a single line-stiffener. Such a structure excited by forces or torques applied to the beam behaves like an uncoupled beam at the driving point. In the far field, power transmitted by flexural waves in the beam is radiated into the plate whilst power transmitted by torsional waves in the beam is not radiated. The plate carries a cylindrical wave with a strong directivity.     

Flutter of Finite-Span Flexible Plates in Uniform Flow

The flutter instability and response of finite-span flexible plates in uniform flow are investigated experimentally. The effects of the plate aspect ratio on its dynamic responses are mainly analyzed. A hysteretic phenomenon is observed and can be described such that the plate flutters spontaneously as the flow velocity is greater than a critical value UC and the plate returns to its stable state as the flow velocity is slowly decreased to another critical one UD. We find that the aspect ratio has a greater effect on UC than on UD. The flutter frequency decreases and the amplitude increases with the increase in the flow velocity. When the flutter instability of the plate occurs, three typical flutter modes are identified and are associated with the aspect ratio and the flow velocity.     

CSNS/RCS脉冲电源均匀传输线障碍点分析

通过研究均匀传输线特征阻抗失配原理,发现传输电缆特征阻抗失配会导致负载终端励磁电流幅值发生畸变。对电源主电路关键参数进行分析,发现均匀传输线匹配阻抗失配会造成磁铁处励磁电流幅值变小,上升时间变短。建立均匀传输线障碍点等效模型,推导出脉冲电源传输线障碍点处反射系数,对串联电阻和并联电阻障碍点深入分析,发现传输线特征阻抗失配,会导致匹配负载处有功功率减小。最后通过高压电缆被击穿故障使其得以验证。     

Sound radiation from a plate reinforced by two sets of parallel stiffeners

A solution is developed for the sound radiation from a point-excited infinite fluid-loaded plate which is reinforced by two sets of parallel stiffeners. The stiffeners are intended to represent the bulkheads and intermediate frames of a hull structure. The solution is found by using Fourier wavenumber transforms, and the stationary phase approximation is used to find an expression for the far field pressure. The effects of the two sets of stiffeners on the radiated pressure depend primarily on the number of frames between successive bulkheads and on the point of application of the force. The presence of frames and bulkheads away from the point of excitation becomes less important as the frequency of the excitation increases.     

Formation of frequency pass and gap bands in an elastic waveguide with a system of obstacles

Using a semianalytical solution to the problem of wave excitation in an elastically supported one-dimensional waveguide with a system of point obstacles, we analyze the relation between the observed effects of blocking-transmission and the discrete spectrum point distribution in the complex frequency plane. We check the assumption, stemming from earlier numerical analysis for two-dimensional elastic waveguides with extended obstacles, on whether the occurrence of transmission frequencies in the blocking range is related to the presence of close-to-the-real-axis points of a discrete spectrum. The number of such spectral points increases in proportion to the number of obstacles, giving in the limit continuous transmission bands described by the Bloch-Floquet theory for infinite periodic structures.     

去耦覆盖层降噪性能评价指标的理论探讨

去耦覆盖层是降低水下结构声辐射的一个重要措施。为了给工程上去耦覆盖层降噪性能评价指标的选择提供理论参考,建立了点激励力作用下敷设去耦覆盖层的四端简支撑矩形板水下振动和声辐射理论模型,定义了可能表征去耦覆盖层降噪性能的五项评价指标。研究结果表明:只有振动传递损失相对独立于基板的长度、宽度和点激励力位置,而且能较好地描述去耦覆盖层隔离基板振动向水层传递的性能;而湿面均方振速插入损失较振动传递损失则能更好地反映辐射声功率插入损失,尤其在低频。作为评价指标,振动传递损失和湿面均方振速插入损失分别有各自的优点和缺点。      

加筋板结构声导纳的面接触判据

通过采用有限元方法建立加筋板模型,计算不同边界条件下具有不同加筋形式的薄板在不同加载面尺寸下的导纳差值,进而得到与频率相关的加筋板面接触判据,揭示了加筋板面导纳和点导纳之间的相关关系,得到了“点”和“面”是否能够等效处理的面接触判据。进一步通过考察薄板的不同加筋形式和加载面形状以及加筋板的速度分布,可以发现:在不加筋、单加筋和十字加筋3种情况中不加筋平板的面接触判据最严格,而十字加筋板的面接触判据最宽松;单加筋板的速度差值与导纳差值的计算结果较为吻合;单加筋板的加载面沿垂直加筋方向的边长越长导纳差值越大。      

Photocatalytic degradation efficacy of Bi4Ti3O12 micro-scale platelets over methylene blue under visible light

〈001〉 textured Bi₄Ti₃O₁₂ platelets with micro scale size were synthesized by a facile molten salt method. The photocatalytic activities of the as-prepared samples were measured with the photodegradation of methylene blue at room temperature under visible light irradiation. The Bi₄Ti₃O₁₂ with the aspect ratio of 35 exhibited good absorption in the visible light region and the photodegradation against methylene blue was higher than that of anatase TiO₂ reference, showing that the high degree of preferred {001} facets on the plate surface benefits the electronic transmission. In addition, the layer-pervoskite structure facilitates the mobility of the photogenerated carriers and hampers their recombination. The above results indicated that the large specific surface area of the as-prepared samples could attribute to the presence of a number of oxygen vacancies and then lead to the good photo-electric property. This work proposed an alternative way to tailor the structure of micro-sized platelets to get excellent properties comparable to the nano materials.     

In-plane vibration of thin elliptic plates submitted to uniform pulsed microwave irradiations

The technique of acoustic generation by microwave excitation in structures is applied here to study the in-plane vibration of full or hollowed elliptic plates. The absorption of pulsed microwave irradiations by a material causes a sudden rise of its temperature and the generation of an acoustic wave by thermoelastic effect. A semi-analytic theoretical model is developed to predict the in-plane displacement fields in elliptic thin plates submitted to a uniform temperature rise. It is assumed that the isotropic and viscoelastic plate constitutive material is submitted to a thermoelastic excitation under a plane stress state. The wave equations that govern the Helmholtz displacement potentials are resolved in an elliptic cylindrical system of coordinates by means of infinite angular and radial Mathieu functions series. The displacement field is finally obtained by taking into account the zero stress conditions on the boundaries of the plates. The comparison between the theoretical and the experimental responses of full and hollowed elliptic plates shows a good agreement that permits the validation of the developed model.     

Characteristics of vertical bent coupling between straight and curved rectangular optical waveguides

In terms of the coupled mode theory (CMT) and the transfer matrix method, we present a technique and relative formulas including the bent coupling coefficient, amplitude coupling ratio, amplitude transmission ratio and propagation power for analyzing the vertical bent coupling between a curved rectangular waveguide and a straight one. Investigations show that the bent coupling appears in an effective coupling region by both sides of the central coupling point. Beyond this effective coupling region, however, the bent coupling is very weak, and the propagation power in the waveguide is closer to a constant. As the bent radius increases, or the thickness of the coupling layer between these two waveguides decreases, this effective coupling region becomes wider, in which the coupling behavior becomes stronger.     

Physical field simulation of the ultrasonic radiation method: An investigation of the vessel,probe position and power

In this paper, the effects of ultrasonic probe position, vessel shape, and ultrasonic input power on the sound pressure distribution in the reactor were investigated by solving the Helmholtz equation using COMSOL Multiphysis^@ software. Three different types of glass containers were used in the study, which are beaker, Erlenmeyer flask, and round bottom flask. The maximum value of sound pressure in the three containers will gradually increase when the distance between the probe and the bottom of the container decreases. When the distance decreases, the area of the high acoustic pressure region in the round bottom flask does not change significantly, while the area of the high acoustic pressure region in the beaker and Erlenmeyer flask increases sharply, which means that the use of the round bottom flask can reduce the influence of the dead zone on the preparation of nanomaterials. In addition, the change in power increases the value of the peak negative acoustic pressure in the vessel, enhancing the response efficiency of ultrasonic cavitation.     

Enhanced optical transmission through a silver plate with a slit array

The near- and far-field properties of a large-scale silver plate with a slit array are studied by applying the FDTD method. The far region scattering properties with different incident angles are also discussed. We find out that the silver plate with a suitable placed narrow slit array can excite the enhanced optical transmission (EOT) by the excitation of the surface plasmon polarition (SPP) and the Fabry-Perot resonance, and the cutoff angle is much larger than the ordinary LEDs. These unique properties suggest possible applications to the light-transparent metal contact.     

含氮氟化类金刚石(FN-DLC)薄膜的研究：(Ⅲ)疏水性能分析

不同沉积条件下，在单晶硅基底上沉积了含氮氟化类金刚石(FN-DLC)薄膜，用静滴接触角/表面张力测量仪测量了水与FN-DLC膜表面的接触角.用X射线光电子能谱、Raman光谱和傅里叶变换吸收红外光谱(FTIR)分析了薄膜的组分和结构.用原子力显微镜观测了薄膜的表面形貌.结果表明，FN-DLC薄膜疏水性能主要取决于薄膜表面的化学结构、薄膜表面极化强度的强弱、以及薄膜的表面粗糙度的大小.sp³/sp²的比值减小，CF₂基团含量增加，薄膜粗糙度增加，接触角增大；反之，则接触角减小.在工艺上，沉积温度和功率的减小，气体流量比r(r=CF4/［CF₄+CH₄］)的增加，都会使水的浸润性变差，接触角增大. 关键词： 氟化类金刚石膜 疏水性 接触角     

有限元法分析不同形状量子点的应变能及弛豫度变化

利用有限元方法研究了不同形状量子点的应变能量分布和弛豫度随着高宽比变化的规律.分析了量子点间距和量子点形状对量子点应变弛豫的影响,定量地讨论了量子点的弛豫度与量子点形状之间的关系.计算结果表明,在不考虑表面能的情况下,当量子点高宽比增加时,弛豫度上升,并且发现平顶金字塔形量子点最先达到稳定;岛间距增大时,量子点内应变能下降,其中立方体形量子点应变能下降最快.研究表明,量子点的弛豫度可以成为控制量子点成岛形状的重要依据. 关键词： 量子点 弛豫度