Influence of various starch types on PCL/starch blends anaerobic biodegradation

Research concentrated on the biodegradable capability of PCL blends with various types of starch in an anaerobic aqueous environment of mesophilic sludge from a municipal wastewater treatment plant. For blend preparation, use was made of a native starch Meritena from maize, another from Waxy – a genetically modified type of maize, as well as Gel Instant, a gelatinized starch, and an amaranth starch. Additional PCL/starch blends were prepared from the same starch types, but these were initially plasticized with glycerol. The biodegradability tests were supplemented with thermo gravimetric analysis (TGA), and differential scanning calorimetry (DSC); morphology was identified using scanning electron microscopy (SEM), plus mechanical properties were also tested. While mixtures of PCL with starches plasticized with glycerol exhibited improved mechanical properties and a higher degree of biodegradation in the anaerobic environment, mixtures of PCL with pure forms of starch were ascertained as rather resistant to the anaerobic aqueous environment. TGA and DSC analysis confirmed the removal of starch and glycerol from the PCL matrix. SEM then proved these results through the absence of starch grains in the samples following anaerobic biodegradation.     

Biodegradation of octanoated starch and its blends with LDPE

Octanoated starch (OCST) with a high degree of substitution (DS = 2.1) is a fully amorphous and hydrophobic thermoplastic material. Its biodegradation was followed in activated sludge from a waste water treatment plant. Its blends with low-density polyethylene (LDPE) were also studied during soil burial for 6 months. From weight loss during the biodegradation period, it was found that OCST, even with such a high degree of substitution, is biodegradable. This was also verified with scanning electron microscopy. Holes were detected on the surface of the films as a consequence of starch consumption by microorganisms. Nevertheless, the rate of biodegradation is very small and depends on the amount of OCST in the blends. The mechanical properties such as tensile strength and elongation at break were measured. A reduction in both was found during the biodegradation period, mainly in blends with a higher amount of OCST.     

Degradation of agar films in a humid tropical climate: Thermal, mechanical, morphological and structural changes

Agar films were subjected to natural weathering exposure in a humid tropical climate for 90 days to determine their biodegradation behavior and functionality. Exposed samples were taken at 15, 30, 45, 60 and 90 days. Mechanical, thermal, structural and morphological properties were determined using tensile test, differential scanning calorimetry (DSC), attenuated reflectance infrared spectroscopy (ATR-FTIR), X-ray diffraction and environmental scanning electron microscopy (ESEM). The photodegradation process and temperature-relative humidity fluctuations promoted a decrease in agar mechanical properties in early exposure stages (30-45 days) caused by a reduction in agar molecular size and a decrease in the number of sulfate groups. These changes alter agar crystallinity, causing contraction that leads to formation of micro-fractures and embrittlement, and promote microbial attack. Accelerated weathering exposure of agar films showed that outdoor climate parameters play an important role in their degradation. These results will aid in further research to determine the potential use of agar as an environmentally friendly solution to the problem of biodegradable composites disposal.     

脂肪族聚碳酸酯(PPC)与聚乳酸(PLA)共混型生物降解材料的热学性能、力学性能和生物降解性研究

通过溶液浇铸法制备了脂肪族聚碳酸酯与聚乳酸的共混物(PPC/PLA).采用示差热分析(DSC)和热重分析(TG)研究了材料的热性能.采用拉伸力学试验研究了共混物的力学性能.通过土壤悬浊拟环境培养降解实验法和扫描电子显微镜分析(SEM)对共混材料的生物降解性能进行了研究.实验结果表明,随着PPC含量的增加,共混物的拉伸强度和杨氏模量降低,而生物降解速率却显著提高.但是,在一定的降解时间内,某些比例共混物的降解速率比100%PPC还要快.综合分析表明,PPC/PLA是力学性能和降解性能可以互补的共混体系.     

Degradation of Mater-Bi/wood flour biocomposites in active sewage sludge

The mechanical properties of Mater-Bi^® are, in general, not adequate for certain applications and the addition of a filler is therefore necessary. Among the different fillers, natural fibres are particularly interesting because they potentially allow improving the performance of the material without compromising its biodegradability.In order to improve the basic mechanical properties of a Mater-Bi grade and to obtain a new, fully biodegradable material, wood flour based composites were prepared by different processing methods. To simulate actual and not laboratory bacterial attack on the prepared materials, in this work we studied the biodegradation of the composites in a real active sewage sludge reactor. In particular, the biodegradation rates were investigated with reference to different pre-treatments of the materials and different environmental conditions (summer and winter). The results showed that wood flour enhances the biodegradability of the materials. The results indicated also strong relationships between the surface roughness and the biodegradation rates (in particular, higher roughness leads to wider bacterial attack). The different processing techniques had direct effects on the overall biodegradation rates. In particular, when higher smoothness and packing is achieved, the biodegradation rate is lower. The mechanical analysis indicated that adding wood flour to Mater-Bi has positive effects on the elastic modulus, but when the bacterial attack becomes critical, a general sudden drop of the mechanical properties is observed.     

Biodegradable blends obtained via reactive blending of polylactide and polyamide-6

Blends of polyamide-6 and polylactide are prepared via reactive compatibilization. Their phase morphologies and compositions are characterized by the methods of IR spectroscopy, optical and scanning electron microscopy, NMR, dynamic mechanical analysis, and continuous extraction in a boiling solvent. It is shown that the formation of hydrogen bonds between polylactide and polyamide-6 substantially improves the compatibility of components. A large proportion of a copolymer is formed as a result of interchain exchange between polyamide-6 and polylactide molecules. The results open new possibilities to produce commercially attractive biodegradable materials with high mechanical and thermophysical characteristics.     

Modern mass spectrometry in the characterization and degradation of biodegradable polymers

In the last decades, the solid-waste management related to the extensively growing production of plastic materials, in concert with their durability, have stimulated increasing interest in biodegradable polymers. At present, a variety of biodegradable polymers has already been introduced onto the market and can now be competitive with non biodegradable thermoplastics in different fields (packaging, biomedical, textile, etc.). However, a significant economical effort is still directed in tailoring structural properties in order to further broaden the range of applications without impairing biodegradation. Improving the performance of biodegradable materials requires a good characterization of both physico-chemical and mechanical parameters. Polymer analysis can involve many different features including detailed characterization of chemical structures and compositions as well as average molecular mass determination. It is of outstanding importance in troubleshooting of a polymer manufacturing process and for quality control, especially in biomedical applications. This review describes recent trends in the structural characterization of biodegradable materials by modern mass spectrometry (MS). It provides an overview of the analytical tools used to evaluate their degradation. Several successful applications of MALDI-TOF MS (matrix assisted laser desorption ionization time of flight) and ESI MS (electrospray mass spectrometry) for the determination of the structural architecture of biodegradable macromolecules, including their topology, composition, chemical structure of the end groups have been reported. However, MS methodologies have been recently applied to evaluate the biodegradation of polymeric materials. ESI MS represents the most useful technique for characterizing water-soluble polymers possessing different end group structures, with the advantage of being easily interfaced with solution-based separation techniques such as high-performance liquid chromatography (HPLC).     

Biodegradable and antibacterial poly(azomethine‐urethane)‐chitosan hydrogels for potential drug delivery application

In this study, biodegradable and antibacterial poly(azomethine‐urethane) (PAMU)‐ and chitosan (CS)‐based hydrogels have been prepared for controlled drug delivery applications. Structural and morphological characterizations of the hydrogels were performed via Fourier transform‐infrared and scanning electron microscopy analyses. Thermal stability, hydrophilicity, swelling, mechanical, biodegradation, protein absorption properties, and drug delivery application of PAMU‐ and CS‐based hydrogels were also investigated. The swelling performance of the hydrogels was studied in acidic, neutral, and alkaline media. Swelling results showed that the hydrogels have higher swelling capacity in acidic and alkaline media than neutral medium. Biodegradation experiments of the hydrogels were also studied via hydrolytic and enzymatic experiments. The drug release property of the hydrogel was carried out using 5‐fluoro uracil (5‐FU), and 5‐FU release capacity of the hydrogels was found in the range from 40.10% to 58.40% after 3 days.     

Curcumin‐loaded biodegradable polyurethane scaffolds modified with gelatin using 3D printing technology for cartilage tissue engineering

We described the curcumin‐loaded biodegradable polyurethane (PU) scaffolds modified with gelatin based on three‐dimensional (3D) printing technology for potential application of cartilage regeneration. The printing solution of poly(ε‐caprolactone) (PCL) triol (polyol) and hexamethylene diisocyanate (HMDI) in 2,2,2‐trifluoroethanol was printed through a nozzle in dimethyl sulfoxide phase with or without gelatin. The weight ratio of HMDI against PCL triol was varied as 3, 5, and 7 in order to evaluate its effect on the mechanical properties and biodegradation rate. A higher ratio of HMDI resulted in higher mechanical properties and a lower biodegradation rate. The use of gelatin increased the mechanical properties, biodegradation rate, and curcumin release due to the surface cross‐linking, nanoporous structure, and surface hydrophilicity of the scaffolds. In vitro study revealed that the released curcumin enhanced the proliferation and differentiation of chondrocyte. The 3D‐printed biodegradable PU scaffold modified with gelatin should thus be considered as a potential candidate for cartilage regeneration.     

Enhancement of mechanical and thermal properties of oil palm empty fruit bunch fiber poly(butylene adipate-co-terephtalate) biocomposites by matrix esterification using succinic anhydride

In this work, the oil palm empty fruit bunch (EFB) fiber was used as a source of lignocellulosic filler to fabricate a novel type of cost effective biodegradable composite, based on the aliphatic aromatic co-polyester poly(butylene adipate-co-terephtalate) PBAT (Ecoflex?), as a fully biodegradable thermoplastic polymer matrix. The aim of this research was to improve the new biocomposites' performance by chemical modification using succinic anhydride (SAH) as a coupling agent in the presence and absence of dicumyl peroxide (DCP) and benzoyl peroxide (BPO) as initiators. For the composite preparation, several blends were prepared with varying ratios of filler and matrix using the melt blending technique. The composites were prepared at various fiber contents of 10, 20, 30, 40 and 50 (wt %) and characterized. The effects of fiber loading and coupling agent loading on the thermal properties of biodegradable polymer composites were evaluated using thermal gravimetric analysis (TGA). Scanning Electron Microscopy (SEM) was used for morphological studies. The chemical structure of the new biocomposites was also analyzed using the Fourier Transform Infrared (FTIR) spectroscopy technique. The PBAT biocomposite reinforced with 40 (wt %) of EFB fiber showed the best mechanical properties compared to the other PBAT/EFB fiber biocomposites. Biocomposite treatment with 4 (wt %) succinic anhydride (SAH) and 1 (wt %) dicumyl peroxide (DCP) improved both tensile and flexural strength as well as tensile and flexural modulus. The FTIR analyses proved the mechanical test results by presenting the evidence of successful esterification using SAH/DCP in the biocomposites' spectra. The SEM micrograph of the tensile fractured surfaces showed the improvement of fiber-matrix adhesion after using SAH. The TGA results showed that chemical modification using SAH/DCP improved the thermal stability of the PBAT/EFB biocomposite.     

微生物合成的β-羟基丁酸酯与β-羟基已酸酯共聚物/聚乳酸共混材料(PHBHHx/PLA)的力学性能与生物降解性研究

通过熔融共混法制备了聚乳酸/微生物产β-羟基丁酸酯与β-羟基己酸共聚物的共混物(PLA/PHBHHx).采用拉伸力学试验研究了共混物的力学性能.通过土壤悬浊培养降解法和扫描电子显微镜(SEM)分析对共混材料的生物降解性能进行了研究.实验结果表明,随着PHBHHx含量的增加,共混物的拉伸强度和杨氏模量降低,而生物降解速率却显著提高.但是,在175h之前,重量组成比为20/80的共混物降解速率比纯PHBHHx还要快.综合分析表明,共混材料PLA/PHBHHx的重量比为20/80时,具有优良的力学性能和生物降解性.     

微生物合成的β-羟基丁酸酯与β-羟基己酸酯共聚物/聚乳酸共混材料(PHBHHx/PLA)的力学性能与生物降解性研究

通过熔融共混法制备了聚乳酸/微生物产β-羟基丁酸酯与β-羟基己酸共聚物的共混物(PLA/PHBHHx)。采用拉伸力学试验研究了共混物的力学性能。通过土壤悬浊培养降解法和扫描电子显微镜(SEM)分析对共混材料的生物降解性能进行了研究。实验结果表明,随着PHBHHx含量的增加,共混物的拉伸强度和杨氏模量降低,而生物降解速率却显著提高。但是,在175h之前,重量组成比为20/80的共混物降解速率比纯PHBHHx还要快。综合分析表明,共混材料PLA/PHBHHx的重量比为20/80时,具有优良的力学性能和生物降解性。     

THERMAL PROPERTY, MISCIBILITY AND CRYSTALLIZATION BEHAVIOR OF POLY（3-HYDROXYBUTYRATE-co- 3-YDROXYHEXANOATE） AND POLY（BUTYLENE SUCCINATE-ADIPATE） （PHBHHX/PBSA） BLENDS

Blends of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) and poly(butylene succinate-adipate) (PBSA), both biodegradable semicrystalline polyesters, were prepared with the ratio of PHBHHx/PBSA ranging from 80/20 to 20/80 by melt mixing method. Differential scanning calorimetry (DSC), thermogravimetry analysis (TGA), dynamic mechanical thermal analysis (DMA), polarizing optical microscopy (POM) and wide angle X-ray diffractometer (WAXD) were used to study the miscibility and crystallization behavior of PHBHHx/PBSA blends. Experimental results indicate that PHBHHx is immiscible with PBSA as shown by the almost unchanged glass transition temperature and the biphasic melt.     

THERMAL PROPERTY, MISCIBILITY AND CRYSTALLIZATION BEHAVIOR OF POLY(3-HYDROXYBUTYRATE-co-3-YDROXYHEXANOATE) AND POLY(BUTYLENE SUCCINATE-ADIPATE) (PHBHHX/PBSA) BLENDS

1. INTRODUCTION Biodegradable polymers have received considerable attention in the last two decades due to their potential applications in the fields related to human life such as environmental protection and ecology. According to the difference in the preparation methods, biodegradable polymers can be classified into two types. One is the biosynthetic polymers, such as bacterialpolyhydroxyalkanoates (PHAs). Among them, the most extensively studied biodegradable thermoplastic polymers ar…     

Gamma Irradiation Effects on Mechanical and Thermal Properties and Biodegradation of Poly(3-hydroxybutyrate) Based Films

Summary: Their biodegradable properties make polyhydroxyalkanoates (PHAs) ideal candidates for innovative applications. Many studies have been primarily oriented to poly(3-hydroxybutyrate) (PHB) and poly(3-hydroxybutyrate-co-3-valerate) (PHBV) and afterwards to blends of PHAs with synthetic biodegradable polymers, such as poly(ε-caprolactone) (PCL). Medical and pharmaceutical devices require sterilization and γ irradiation could provide a proper alternative since it assures storage stability and microbiological safety. This contribution presents the effect of γ irradiation on the mechanical and thermal properties and on the biodegradation of PHB, PHBV and a commercial PHB/PCL blend. Samples, prepared by compression moulding, were irradiated in air at a constant dose rate of 10 kGy/h, from 10 to 179 kGy. Polymer chain scission was assessed by changes in the molecular weight, thermal properties and tensile behaviour. The correlation between absorbed dose and changes in the mechanical properties and biodegradation is discussed in detail. The optimum dose to guarantee microbiological sterilization without damage of the structure or meaningful loss of the mechanical properties is also reported.     

Chitosan based hybrid hydrogels for drug delivery: Preparation,biodegradation, thermal,and mechanical properties

In the present paper, biodegradable hybrid hydrogels were prepared by using chitosan as a natural polymer and polyurethane containing azomethine as a synthetic polymer for the drug delivery application for 5-fluorouracil. The fabricated hydrogels were characterized via FT-IR and SEM analysis. Besides, the thermal, mechanical, and wettability properties, water uptake, biodegradation, protein absorption, drug loading, and release behaviors of the hybrid hydrogels were studied. The obtained results indicated that the fabricated hybrid hydrogels have exhibited good mechanical, hydrophilic, water uptake, and biodegradation behaviors. The hybrid hydrogels also showed 50% drug release amounts and they could be a good candidate for the controlled delivery of 5-FU due to these properties.     

Biobased films prepared from NaOH/thiourea aqueous solution of chitosan and linter cellulose

In the present study, films based on linter cellulose and chitosan were prepared using an aqueous solution of sodium hydroxide (NaOH)/thiourea as the solvent system. The dissolution process of cellulose and chitosan in NaOH/thiourea aqueous solution was followed by the partial chain depolymerization of both biopolymers, which facilitates their solubilization. Biobased films with different chitosan/cellulose ratios were then elaborated by a casting method and subsequent solvent evaporation. They were characterized by X-ray analysis, scanning electron microscopy (SEM), atomic force microscopy (AFM), thermal analysis, and tests related to tensile strength and biodegradation properties. The SEM images of the biofilms with 50/50 and 60/40 ratio of chitosan/cellulose showed surfaces more wrinkled than the others. The AFM images indicated that higher the content of chitosan in the biobased composite film, higher is the average roughness value. It was inferred through thermal analysis that the thermal stability was affected by the presence of chitosan in the films; the initial temperature of decomposition was shifted to lower levels in the presence of chitosan. Results from the tests for tensile strength indicated that the blending of cellulose and chitosan improved the mechanical properties of the films and that an increase in chitosan content led to production of films with higher tensile strength and percentage of elongation. The degradation study in a simulated soil showed that the higher the crystallinity, the lower is the biodegradation rate.     

Preparation and characterization of poly(propylene carbonate)/montmorillonite nanocomposites by solution intercalation

Poly(propylene carbonate) (PPC) is a new biodegradable aliphatic polycarbonate. However, the poor thermal stability and low glass transition temperatures (T_g) have limited its applications. To improve the thermal properties of PPC, organophilic montmorillonite (OMMT) was mixed with PPC by a solution intercalation method to produce nanocomposites. An intercalated-and-flocculated structure of PPC/OMMT nanocomposites was confirmed by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The thermal and mechanical properties of PPC/OMMT nanocomposites were investigated by thermal gravimetric analysis (TGA), differential scanning calorimetric (DSC), and electronic tensile tester. Due to the nanometer-sized dispersion of layered silicate in polymer matrix, PPC/OMMT nanocomposites exhibit improved thermal and mechanical properties than pure PPC. When the OMMT content is 4 wt%, the PPC/OMMT nanocomposite shows the best thermal and mechanical properties. These results indicate that nanocomposition is an efficient and convenient method to improve the properties of PPC.     

Synthesis, characterization and properties of high molecular weight poly(butylenes succinate) reinforced by mesogenic units

To increase the molecular weights of the synthesized liquid crystalline aromatic/aliphatic copolyesters and to avoid crosslinking, a solution polymerization of the prepolymer and chain extender hexamethylene diisocyanate was adopted. The effects of chain extension on polyester molecular weights, thermal and mechanical properties, and biodegradable behaviors were investigated respectively. The catalysis mechanism and the copolyesters morphological textures were also investigated. The synthesized copolyesters were characterized by means of Fourier transform infrared spectra (FTIR), gel permeation chromatography (GPC), viscosity measurements, differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarizing light microscopy (PLM), scanning electron microscopy (SEM) and mechanical property measurements. It was found that inherent viscosities and the molecular weights of the copolyesters were remarkably increased under the action of catalyst, leading to a increase in the tensile strength. The degree of relative crystallinity, the melting temperature, and the rate of degradation decreased after chain extension.     

Controlled drug release behavior of metformin hydrogen chloride from biodegradable films based on chitosan/poly(ethylene glycol) methyl ether blend

In this study, novel smart drug release films were prepared by blending chitosan with polyethylene glycol methyl ether (PEGME), also named as methoxy polyethylene glycol (mPEG), for controlled drug release applications. The polymeric films were characterized by Fourier transform infra-red for functional groups analysis, scanning electron microscopy for morphology and X-ray photoelectron spectroscopy for chemical and surface analysis followed by mechanical and thermal analysis. The mechanical properties showed that with the addition of PEGME (40%), the tensile strength and elongation break were increased up to 34.14 MPa and 26.40%, respectively as compared to the controlled sample (without PEGME). The developed biodegradable films were tested for Metformin hydrogen chloride release ability at a particular rate in phosphate buffer saline solution at pH 7.4. The results showed that chitosan/PEGME blends could be employed for controlled drug release and other biomedical applications.