四元Mg0.9Ti0.1Ni0.9X0.1(X=Mn,Zn,Co,Fe)系列合金的制备及性能研究

用机械合金化法合成了Mg0.9Ti0.1Ni0.9X0.1(X=Mn, Zn, Co, Fe)系列合金. X射线衍射(XRD)结构分析表明, 用X部分替代Ni后, 促进了Mg0.9Ti0.1Ni合金的非晶化过程. 用Co和Fe部分替代Ni提高了合金的放电容量, 但却降低了合金的循环稳定性. 用Zn和Mn部分替代Ni提高了合金电极的循环寿命, 尤其是Mg0.9Ti0.1Ni0.9Zn0.1合金电极经10个充放电循环后, 其放电容量仍可达到313.8 mA·h/g. 对添加Co后的合金进行p-c-T测试发现, Mg0.9Ti0.1Ni0.9Co0.1合金的吸放氢容量明显比Mg0.9Ti0.1Ni合金高, 这与电化学所测到的结果一致.     

四元Mg0.9Ti0.1Ni0.9X0.1(X=Mn,Zn,Co,Fe)系列合金的制备及性能研究

用机械合金化法合成了Mg0·9Ti0·1Ni0·9X0·1(X=Mn,Zn,Co,Fe)系列合金.X射线衍射(XRD)结构分析表明,用X部分替代Ni后,促进了Mg0·9Ti0·1Ni合金的非晶化过程.用Co和Fe部分替代Ni提高了合金的放电容量,但却降低了合金的循环稳定性.用Zn和Mn部分替代Ni提高了合金电极的循环寿命,尤其是Mg0·9Ti0·1Ni0·9Zn0·1合金电极经10个充放电循环后,其放电容量仍可达到313·8mA·h/g.对添加Co后的合金进行p-c-T测试发现,Mg0·9Ti0·1Ni0·9Co0·1合金的吸放氢容量明显比Mg0·9Ti0·1Ni合金高,这与电化学所测到的结果一致.     

钛和锆的添加对MgNi型合金电极电化学性能的影响

用机械球磨法（MA）成功合成了镁基储氢合金MgNi, Mg0.9Ti0.1Ni和Mg0.9Ti0.1Ni0.9Co0.1。研究了其结构和电化学性能。X射线衍射（XRD）和扫描电镜（SEM）结果表明合金为非晶结构，并有少量的Ni衍射峰存在。充放电测试结果表明这一系列合金具有很好的电化学活性。Ti和Co的替代使合金的循环稳定性好于MgNi合金。50周充放电循环后，Mg0.9Ti0.1Ni0.9Co0.1合金的放电容量明显好于MgNi合金，Mg0.9Ti0.1Ni0.9Co0.1的放电容量比MgNi合金高102.8%，比Mg0.9Ti0.1Ni合金高45.49%。在充放电循环过程中，合金电极容量衰减的主要原因是在合金电极表面Mg变成了Mg(OH)2。Tafel极化测试表明Ti和Co的添加可以提高合金电极在碱液中的抗腐蚀性能和提高合金电极的循环稳定性。EIS测试结果表明Ti和Co的替代可以明显提高MgNi型合金表面的电催化活性。     

硼的添加对Ti0.26Zr0.07V0.24Mn0.1Ni0.33贮氢合金结构和电化学性能的影响

Ti0.26Zr0.07V0.24Mn0.1Ni0.33Bx(x=0~0.10)系列合金均有V基固溶体相和C14型Laves相两相组成。添加B可提高Ti0.26Zr0.07V0.24Mn0.1Ni0.33合金的放电容量,Ti0.26Zr0.07V0.24Mn0.1Ni0.33B0.1合金电极在60 mA·g-1电流放电时的放电容量达到476.7 mAh·g-1。B的添加不同程度地降低了合金的高倍率放电性能,使合金电极表面上电化学反应的电荷转移电阻(R ct)显著增加,交换电流密度(I0)显著降低。添加B可显著改善Ti0.26Zr0.07V0.24Mn0.1Ni0.33合金电极的高温放电性能,Ti0.26Zr0.07V0.24Mn0.1Ni0.33B0.025合金电极在343 K高温下其放电容量达到525.6 mAh·g-1。     

Mg0.9Ti0.1Ni0.85Co0.15合金的石墨粉及镍粉球磨表面包覆性能

选用非晶态的Mg0.9Ti0.1Ni0.85Co0.15合金粉末与石墨粉及镍粉进行球磨表面包覆。SEM分析结果表明,己包覆石墨和镍粉的合金表面上吸附着一层小的颗粒,形成薄层将原来的合金表面包覆起来。使用XPS分析了合金表面元素。结果表明,包覆石墨粉后,合金表面碳元素的质量分数和原子分数均增加,Mg的质量分数从22.74%减小至22.23%,原子分数从36.43%减小到32.94%,从而减小了Mg在碱液中的腐蚀几率,提高合金的抗腐蚀性能;包覆镍粉后,合金表面Ni的质量分数由59.89%增加到60.04%,原子分数由40.63%增加到41.02%,形成合金表面富Ni的保护层,提高了合金的抗腐蚀性能。充放电循环测试表明,循环30周后,包覆石墨粉的合金电极容量保持率为32.05%,包覆镍粉的合金电极容量保持率为41.26%,而未包覆的电极容量保持率仅为17.88%。合金电极极化曲线测试结果表明,石墨或镍粉的包覆提高了Mg0.9Ti0.1Ni0.85Co0.15合金电极的循环稳定性和在KOH碱液中的抗腐蚀性能。     

添加元素对AB2型Laves相合金电化学性能的影响

比较系统地研究了AB2型Laves相合金Zr0.9Ti0.1Ni0.1Mn0.7V0.3M0．1(M=None，Ni．Mn．V．Co．Cr．Al．Fe，Mo．Si．C．Zn，Cu和B)的相结构和电化学性能以及高温和低温放电性能等．结果表明．14种合金均具有六方C14型Laves相的主相晶体结构．同时，含有少量立方Cl5型Laves相和一些由Zr9Ni11及ZrNi组成的非Laves相；添加V和Mn可提高AB2合金的放电容量；添加B和Mn则显著提高了AB2合金的高倍率放电性能和低温放电容量；添加Al，C．Si和Co对合金电极的循环稳定性改善明显；而Mn．Ni．V．Fe．Cu．Mo和B等却不同程度地降低了循环稳定性；添加Si．Mo，V，Cr和Al可明显改善合金电极的自放电性能；添加Si．Cr．V可显著改善AB2合金电极的高温放电性能．讨论了各种添加元素影响合金性能的可能原因．     

Mg0.9Ti0.1Ni1－xCox (x＝0.05, 0.1, 0.15, 0.2)合金的合成及电化学性能研究

采用机械合金化法合成了Mg_0.9Ti_0.1Ni_1－xCo_x (x＝0.05, 0.1, 0.15, 0.2)系列四元合金, 并对该系列合金的结构和电化学性能等方面进行了研究. 球磨100 h的该系列合金, XRD结果表明, X射线衍射峰均呈现宽化趋势, 基本呈非晶态. 充放电结果表明, 该系列合金具有较好的活化性能, 它们的循环稳定性明显好于MgNi合金, 其中Mg_0.9Ti_0.1Ni_0.8Co_0.2最大放电容量最高, 为427.5 mAh•g^－1. 在充放电循环过程中, Mg在合金表面形成了Mg(OH)₂是合金电极衰减的主要原因. 腐蚀曲线的测试结果表明, Co的添加可以提高合金电极在碱液中的抗腐蚀能力, 从而提高了电极的循环稳定性.     

Mg1.75Al0.25Ni1-xCrx (0≤x≤0.2)合金的制备及其性能

用扩散烧结法制备了Mg1.75Al0.25Ni1-xCr（0≤x≤0．2）系列合金,XRD结构分析表明,用Cr部分替代Mg1.75Al0.25Ni中的Ni,合金的晶体结构并不发生改变,主相为具有立方Ti2Ni结构的Mg3AlNi2相,只是其晶格常数α变大,Cr的替代提高了合金的放电容量,经过一个充放电循环后达到最大值。当x为0．1时,有利于提高合金电极的循环稳定性。测试4种合金阳极极化曲线发现,其腐蚀电位由正到负的顺序为Mg1.75Al0.25Ni0.9Cr0.1〉Mg1.75Al0.25Ni〉Mg1.75Al0.25Ni0.8Cr0.2〉Mg2Ni,说明Mg1.75Al0.25Ni0.9Cr0.1合金具有相对较好的抗腐蚀性．该系列合金循环稳定性结果也支持这一结论．用球磨方法改变合金性能,发现合金的相组成和相结构在球磨后均发生了变化,合金不再需要活化过程,但其放电容量并没有得到提高。     

Mg0.9－xTi0.1PdxNi(x=0.04～0.1)贮氢合金电极腐蚀行为研究

研究了Pd部分替代Mg对Mg0.9－xTi0.1PdxNi(x=0.04～0.1)贮氢合金腐蚀性能的影响. 利用机械合金化方法制备了Mg0.9－xTi0.1PdxNi(x=0.04～0.1)贮氢合金. XRD和TEM分析表明经120 h球磨后该合金完全非晶化. 循环充放电测试结果表明, Pd的替代有效地延长了Mg0.9－xTi0.1PdxNi(x=0.04～0.1)合金的循环寿命. 采用开路电位测量, 阳极极化, 电化学阻抗和X射线光电子能谱研究了该合金的腐蚀行为. 结果表明, 随着Pd含量增加, 合金腐蚀电位正移, 初始腐蚀电流下降, 腐蚀电流增加的速度变缓. 采用本文提出的等效电路模型较好地拟合了合金的电化学阻抗谱. 分析表明, 随着Pd含量的增加, 合金表面钝化膜厚度和电阻逐渐增大. X射线光电子能谱分析表明, Pd的加入减弱了合金在充放电过程中的氧化程度. 当Pd含量达到0.1时, Mg0.9－xTi0.1PdxNi(x=0.04～0.1)合金的耐腐蚀性能最好, 其放电容量保持率最高.     

稀土元素对Ti0.26Zr0.07V0.24Mn0.1Ni0.33贮氢合金微观结构和电化学性能的影响

本文研究了稀土元素对Ti0.26Zr0.07V0.24Mn0.1Ni0.33合金的微观结构和电化学性能的影响。结果表明,Ti0.26Zr0.07V0.24-xMn0.10Ni0.33REx(RE=Ce,Nd,Gd;x=0.01)合金均有V基固溶体相和C14型Laves相两相组成。合金中两相的晶格参数随加入稀土元素的不同而发生变化。稀土元素部分取代可改善合金电极的活化性能。然而,对合金电极的其他性能影响因元素种类不同而各异。Ce取代增大了合金电极的最大放电容量,Nd元素可以有效改善合金的高倍率放电性能。工作温度对合金电极的放电容量影响较大,Nd和Gd在333 K最大放电容量可达426和465 mAh.g-1。过高的温度使其循环容量衰减加剧。     

氧化钴在二氧化钛表面的单层分散及结构研究

利用X射线光电子能谱(XPS)、X射线衍射(XRD)及扩展的X射线精细结构谱(EXAFS)对氧化钴在二氧化钛表面的分散及结构进行了系统研究。结果表明：氧化钴能够在二氧化钛表面实现单层分散,其分散阈值为每平方纳米的二氧化钛分布1．4个钴原子。当负载量小于分散阈值时,钴以二价存在并形成分立的钴氧六配位[CoO6];而当负载量大于分散阈值时,晶体Co3O4在二氧化钛表面形成,钴以两种形式存在,即分散态的钴氧六配位[CoO4]和晶态的Co3O4。实验还表明二氧化钛对二价钴具有明显的稳定作用。     

Determination of microcystins in biological samples from freshwater fish

A new HPLC–DAD method has been developed to identify and quantify free microcystins (MC) in biological samples from fish (intestine and liver). The toxins were extracted from 500 mg sample with a mixture of methanol–water (85 : 15, v/v) and the extracts obtained were purified employing immunoaffinity columns (IAC). The purification step was optimised by a full factorial 3² design. MC were separated using conventional C18 column and an acetonitrile-acidified water (pH 3) gradient. Detection and quantification limits resulted equal for the two toxins assayed (MC-RR and MC-LR) and were 0.15 and 0.5 µg g^?1, respectively. The accuracy for each MC in liver samples were 96% (range 80–113%) for MC-RR and 101% (range 93–118%) for MC-LR. The results were slightly lower for intestine samples, with recoveries ranging between 85% (75–93%) for MC-RR and 88% (80–97%) for MC-LR. The proposed method was applied for the determination of free MC in fish intoxicated with these toxins, in order to determine its utility to evaluate the potential risks for human health if MC-contaminated fish are consumed. The results showed the transference of MC-LR from cyanobacterial cells to fish tissues.     

活性炭纤维电极生成羟基自由基降解酸性红B

分别采用具有吸附催化性能的活性炭纤维(ACF)作为阳极和阴极对水中偶氮染料酸性红B (ARB)的电化学降解情况进行了系统研究. 研究表明两种体系均可较好降解ARB, 可达到色度完全去除, 但ACF作为阴极电芬顿对有机物的矿化程度远远高于以ACF作为阳极时的矿化程度, 其TOC去除率达到70%, 高于阳极体系的30% TOC去除率. 通过电子自旋捕集技术(ESR)检测两种反应体系中产生的活性中间体, 发现在两种体系中均有高活性的羟基自由基生成, ACF阴极体系中产生的羟基自由基的量远远高于阳极体系产生量, 这是阴极体系有机物矿化效果较好的根本原因. 还对电流强度和初始pH的影响进行了研究, 并对两个体系反应机理进行了讨论.     

高效液相色谱-串联质谱法测定淡水养殖池塘水体及鱼虾体内的藻毒素

采用高效液相色谱-串联质谱法测定了淡水养殖池塘水体及鱼虾体内藻毒素MC-LR和MC-RR。水样经微孔滤膜过滤后,通过固相萃取柱富集净化。鱼、虾冻干后粉碎,以甲醇水溶液提取,提取液经固相萃取柱富集净化。采用UPLC BEH C18色谱柱(100×2.1mm,3.5μm),以0.1%甲酸水溶液和含0.1%甲酸乙腈溶液为流动相,质谱采用选择离子监测模式测量。结果表明,藻毒素的质量浓度在0.5~500μg·L~(-1)范围内时,峰面积与样品浓度呈良好线性关系。MC-LR和MC-RR的方法检出限分别为0.05μg·L~(-1)和0.08μg·L~(-1)。藻毒素在空白水样中的加标回收率为88.5%~98.5%,相对标准偏差为5.2%~8.3%;在鱼、虾组织中的加标回收率为63.8%~85.2%,相对标准偏差为6.7%~9.8%。实际测得某养殖池塘水中存在藻毒素污染,且部分水产品中检测到了MC-LR和MC-RR。     

Determination of microcystins in fish by solvent extraction and liquid chromatography

A liquid chromatography electrospray mass spectrometry (LC/ESI/MS) method has been developed to identify and quantify microcystins in fish liver and intestine. Microcystins (MCs) were extracted from 500 mg sample with methanol-water (85:25, v/v) and the extracts concentrated to 250 microl. The parameters were optimized by a full factorial 2(3) design. Neither laborious pre-treatment nor clean up were necessary. MCs were separated using conventional C18 column and an acetonitrile-acidified water (pH 3) gradient. Negative samples (without MCs) were discriminated by liquid chromatography diode array detection (LC/DAD). The limits of detection (LOD) and the limits of quantification (LOQ) resulted equal for MC-RR, MC-YR, and MC-LR and were 0.1 and 0.5 microg g(-1), respectively. MCs recoveries at three levels in spiked samples (0.5-3.0 microg g(-1)) were > 92%, with relative standards deviations (RSDs) < 16% for liver samples and > 68% with RSDs < 18% for intestine samples. The proposed method was applied to determine MC-LR in exposed fish to evaluate the bioaccumulation risk. The results showed the transference of MC-LR from cyanobacterial cells to fish tissues.     

甲基丙烯酸酯毛细管整体柱分离微囊藻毒素的研究

以甲基丙烯酸丁酯为单体,乙二醇二甲基丙烯酸酯为交联剂,在致孔剂存在的条件下原位聚合制备了甲基丙烯酸丁酯毛细管整体柱(150 μm i.d.)。实验中优化了用此整体柱分离3种微囊藻毒素(MC-LR,-YR和-RR)的色谱条件(流动相种类、缓冲溶液浓度、pH、流动相流速),建立了微囊藻毒素的整体柱毛细管液相色谱分离方法,该法可以在9 min之内实现3种微囊藻毒素的基线分离。将该方法应用于实际水样中微囊藻毒素的分析,成功实现了培养水样和巢湖水样中微囊藻毒素的快速分离,两种样品中均检测到MC-LR。结果表明,所制备的甲基丙烯酸酯毛细管整体柱具有良好的重现性、渗透性,在微囊藻毒素的常规检测中具有很好的应用前景。     

2,4-dichlorophenol degradation by an integrated process: photoelectrocatalytic oxidation and E-Fenton oxidation

A new reactor system was designed for an integrated process involving photoelectrocatalytic oxidation (PECO) and electro-Fenton (E-Fenton) oxidation. Its efficiency was evaluated in terms of 2,4-dichlorophenol (2,4-DCP) degradation in aqueous solution. In this process, a TiO2 electrode and an iron (Fe) electrode were used as anodes in parallel, while graphite felt (GF) was used as a cathode. When an electrical current is applied between the anodes and the cathode, the iron anode can release Fe2+ and the GF cathode can generate H2O2 continuously in the reaction solution. Under UV-A illumination, while a H2O2-assisted PECO reaction occurs on the surface of the TiO2 photo anode, an E-Fenton reaction takes place in the solution. The experimental results demonstrated that 2,4-DCP degradation in aqueous solution was greatly enhanced because of the interaction between the two types of reactions. Moreover, the effect of pH as an important factor was investigated. It was found that the combined reaction becomes less pH sensitive than the typical E-Fenton reaction and may be suitable for application in a wide pH range.     

超高效液相色谱–串联质谱法测定饮用水中微囊藻毒素

建立饮用水中微囊藻毒素(MC–RR,MC–LR)的超高效液相色谱–串联质谱检测方法。样品经PVDF针式过滤头过滤后直接进样,采用喷雾正离子源(ESI~+)和多重反应监测模式(MRM)测定。MC–RR的质量浓度在0.02~10.00μg/L范围内与色谱峰面积呈良好的线性,线性相关系数r~2=0.998 9,检出限为0.096μg/L,测定结果的相对标准偏差为6.6%~9.1%(n=7),加标回收率为99.0%~103.0%。MC–LR的质量浓度在0.1~20μg/L范围内与色谱峰面积呈良好的线性,线性相关系数r~2=0.999 2,检出限为0.188μg/L,测定结果的相对标准偏差为4.3%~10.0%(n=7),加标回收率为93.0%~114.0%。该方法灵敏度高、重现性好,可用于饮用水中微囊藻毒素的检测。     

Fe(Ⅲ)-草酸-葡萄糖酸钙媒质体系间接电化学还原及棉织物染色的研究

应用循环伏安法研究了Fe(Ⅲ)-草酸-葡萄糖酸钙媒质体系的电化学行为及其可能的反应机理,实验表明Fe(Ⅱ)-葡萄糖酸盐起着最终的还原作用。电解还原时间、工作电压和阴极面积这三个因素影响着电流效率,在Fe(Ⅲ)-草酸-葡萄糖酸钙媒质体系中,还原大红R的电流效率最高可达89%,其电解还原时间10min,工作电压4V,阴极面积40cm2。     

Highly sensitive detection and discrimination of LR and YR microcystins based on protein phosphatases and an artificial neural network

The inhibition characteristics of three different protein phosphatases by three microcystin (MC) variants--LR, YR, and RR--were studied. The corresponding K (I) for each enzyme-MC couple was calculated. The toxicity of MC varies in the following order: MC-LR > MC-YR > MC-RR. The sensitivity of the enzymes increased in the following order: mutant PP2A < mutant PP1 < natural PP2A. The best limit of detection obtained was 21.2 pM MC-LR using the most sensible enzyme. Methanol, ethanol, and acetonitrile up to 2 % (v/v) may be used in inhibition measurements. An artificial neural network (ANN) was used to discriminate two MC variants--LR and YR--using the differences in inhibition percentages measured with mutant PP1 and natural PP2A. The ANN is able to analyze mixtures with concentrations ranging from 8 to 98 pM MC-LR and 31 to 373 pM MC-YR.