CNTs/TiO2多孔复合膜的组装及光催化性能

提出了一种在掺氟的SnO2(FTO)导电玻璃上组装碳纳米管(CNTs)/Fe-Ni/TiO2多孔复合膜光催化剂的新方法.采用喷涂热解法(SPD)将掺杂镍和铁的含有嵌段聚合物P123的二氧化钛前驱体溶胶涂覆在FTO导电玻璃上,制备Fe-Ni/TiO2多孔膜,再采用化学气相沉积法(CVD)在Fe-Ni/TiO2膜上原位生长CNTs,得到CNTs/Fe-Ni/TiO2多孔复合膜光催化剂.CNTs/Fe-Ni/TiO2复合膜具有多级孔结构特征,在TiO2表面原位生长的CNTs不但具有较好的石墨化结构,且CNTs较均匀地分布在整个膜层的孔中.考察了CNTs/Fe-Ni/TiO2复合膜光催化剂的结构和性能,并通过降解甲基橙溶液评价了复合膜的光催化活性.结果表明,CNTs的复合及铁和镍的掺杂等改性显著提高了TiO2膜材料的光催化活性.     

过渡金属掺杂和碳纳米管（CNT）接枝双重改性TiO2光催化剂

提出了一种过渡金属掺杂和碳纳米管(CNT)双重改性TiO2的新方法:首先采用溶胶-凝胶法合成掺杂镍和铁的二氧化钛基催化剂,然后采用流化床化学气相沉积方法(FBCVD)在二氧化钛基催化剂表面接枝生长CNT,得到CNT/Fe-Ni/TiO2复合光催化剂.通过X射线衍射、扫描电子显微镜、比表面分析、拉曼光谱、紫外-可见吸收光谱、荧光光谱等方法考察了双重改性复合光催化剂CNT/Fe-Ni/TiO2的结构和性能,通过降解亚甲基蓝溶液评价了双重改性复合光催化剂的活性.结果表明,在TiO2表面接枝的CNT具有较好的石墨化结构,CNT生长过程中小部分TiO2由锐钛矿向金红石晶型转变.过渡金属和CNT双重改性有效地克服了TiO2的比表面积小、量子效率低等缺点,明显提高了TiO2的光催化活性.     

TiO2纳米管修饰镍电极及其光催化辅助电解水制氢性能研究

本文通过水热法制备二氧化钛纳米管(TiO2NT),并用制备的TiO2NT对碱性电解水制氢装置的镍片阳极进行修饰,在电解水的基础上,通过光催化与电解过程的耦合,提出并实现了光催化辅助电解水制氢过程。通过XRD、UV-Vis、FE-SEM、AFM和光催化辅助电解水制氢等方法对试样的结构和性能进行了表征和测试。结果表明,在紫外光照条件下,用TiO2NT修饰镍片阳极的光催化辅助电解水过程的产氢速率比单纯电解水提高了61%。     

ZnFe2O4/TiO2纳米管阵列电极的制备及光电催化降解苯酚的研究

采用阳极氧化法和电沉积法制备出具有可见光响应的ZnFe2O4/TiO2纳米管阵列电极.用环境扫描电子显微镜(ESEM)、X-射线衍射(XRD)和透射电子显微镜(TEM)对制备的ZnFe2O4/TiO2纳米管阵列电极的表面形貌和结构进行了表征.结果表明,该方法成功地将ZnFe2O4纳米颗粒均匀分散在TiO2纳米管中,分布在管口处的较少.同时,详细讨论了反应物浓度、沉积时间、循环次数、沉积电压对ZnFe2O4/TiO2纳米管阵列电极性能的影响.通过在可见光下降解苯酚评价了复合电极的光催化活性,实验结果表明:由于ZnFe2O4和TiO2之间的协同效应,复合电极的光响应范围扩展到了可见光区域,光电催化活性提高1.5～2倍.     

Fe-Ni/TiO2纳米管阵列电极的制备、表征及光电催化还原五氯酚活性

采用阳极氧化法和浸渍电沉积联用法制备了不同负载量的Fe-Ni/TiO2纳米管阵列电极. 通过扫描电子显微镜(SEM)、 X射线光电子能谱(XPS)和电化学测量等手段对样品的微观形貌、 晶体结构和光电响应等特性进行分析. 考察了在0.6 V偏压下, 所制备的电极对五氯酚的光电催化还原性能. 结果表明, 适量的Fe和Ni纳米颗粒的负载, 降低了TiO2纳米管阵列光生电子-空穴对的复合几率; 浸渍电沉积5次的Fe-Ni/TiO2纳米管阵列电极光电催化还原降解五氯酚的效率为91.35%, 明显高于TiO2纳米管阵列电极.     

Fe_2O_3/TiO_2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO2纳米管阵列,采用化学浴方法在TiO2纳米管阵列上修饰了Fe2O3纳米颗粒。利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能。结果表明,Fe2O3纳米颗粒的修饰将TiO2纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe2O3/TiO2纳米管阵列的光电流是未修饰的TiO2纳米管阵列的9倍。而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO2纳米管阵列高出30%。     

脉冲沉积制备Cu_2O/TiO_2纳米管异质结的可见光光催化性能

在用阳极氧化法制备有序排列TiO2纳米管阵列薄膜的基础上,引入脉冲沉积工艺,成功实现了均匀、弥散分布的Cu2O纳米颗粒修饰改性TiO2纳米管阵列,形成Cu2O/TiO2纳米管异质结复合材料.利用场发射扫描电镜(FESEM)、场发射透射电镜(FETEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外-可见漫反射光谱(UV-Vis DRS)对样品进行表征,重点研究了Cu2O/TiO2纳米管异质结的光电化学特性和对甲基橙(MO)的可见光催化降解性能.结果表明,Cu2O纳米颗粒均匀附着在TiO2纳米管阵列的管口和中部位置,所制备的Cu2O/TiO2纳米管异质结具有高效的可见光光催化性能;在浓度为0.01 mol?L-1的CuSO4溶液中制得的Cu2O/TiO2纳米管异质结表现出最好的电化学特性和光催化性能;另外,对Cu2O纳米颗粒影响光催化活性的机理进行了讨论.     

碳纳米管/氧化锌纳米复合材料的制备及其形貌控制

0引言碳纳米管(CNT)优良的力学、电学、热学性能使其在材料、储能、传感等许多领域都有广泛的应用前景,近年来,以碳纳米管为载体制备的纳米复合材料因其独特的应用潜力而受到广泛关注:彭峰等[1]用FeSO4-H2O2体系修饰碳纳米管,成功地制备了由碳纳米管负载的Fe2O3催化剂;Chen等[2]用溶胶凝胶法制备了CNT/SnO复合材料,作为Li离子电池阴极材料,测试表明它的电化学性能比单独的CNT和SnO材料都有所增强;Jitianu等[3]用溶胶凝胶和水热方法得到不同形貌的TiO2/CNT复合结构,这种新型的纳米复合材料在光催化方面有着重要的应用前景。纳米Z…     

Al-Y共掺杂对ZnO纳米棒形成及光催化活性的影响

以Zn(NO3)2·6H2O,Al(NO3)3·9H2O,Y(NO3)3·6H2O和Na OH为原料,采用溶液法制备了Al-Y共掺杂Zn O光催化剂(Al-Y/Zn O),并用X射线衍射(XRD)、扫描电镜(SEM)考察了Al,Y共掺杂对Zn O纳米棒形成及形貌的影响。结果表明,Al-Y共掺杂对Zn O晶粒大小基本没有影响,但会严重抑制Zn O纳米棒的生成,促使碱式硝酸锌(Zn5(OH)8(NO3)2·2H2O)的生成。以甲基橙(MO)为模型污染物考察了Al-Y共掺杂对Zn O纳米棒光催化活性的影响。结果发现,适量的Al-Y共掺杂会显著提高Zn O纳米棒的光催化活性。     

Fe、N共掺杂TiO2纳米管阵列的制备及可见光光催化活性

应用电化学阳极氧化法结合浸渍和退火后处理制备了Fe和N共掺杂的TiO2纳米管阵列光催化剂,并用场发射扫描电镜(FESEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)和俄歇电子能谱(AES)仪对其进行了表征.结果表明,Fe、N共掺杂对TiO2纳米管阵列的形貌和结构没有明显影响,Fe和N均掺入了TiO2晶格.紫外-可见(UV-Vis)漫反射光谱显示Fe和N共掺杂TiO2纳米管阵列的吸收带边较纯TiO2纳米管阵列和单一掺杂TiO2纳米管阵列红移,可见光吸收增强.以可见光催化降解罗丹明B(RhB)考察了材料的光催化活性,Fe和N共掺杂TiO2纳米管阵列对RhB的降解速率较纯TiO2纳米管阵列和单一掺杂TiO2纳米管阵列明显提高,证明了Fe、N共掺杂产生的协同效应提高了TiO2纳米管阵列在可见光照射下的光催化活性.     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.