Plasmon resonances in gold-coated tilted fiber Bragg gratings

The transmission spectrum of fiber Bragg gratings with gratings planes tilted at a small angle (2 degrees -10 degrees) relative to the fiber axis shows a large number of narrowband cladding mode resonances within a 100 nm wide spectrum. When a gold coating with a thickness between 10 and 30 nm is deposited on the fiber, the transmission spectrum shows anomalous features for values of the outside medium refractive index between 1.4211 and 1.4499. These features are shown to correspond to the excitation of surface plasmon resonances at the external surface of the gold film.     

不同包层直径的倾斜光纤光栅折射率传感特性

倾斜光纤光栅的透射谱中有纤芯模和大量的包层模,它们具有与布拉格光栅相同的温度特性.利用HF酸腐蚀的方法得到具有不同包层直径的倾斜光纤光栅,研究了其对外界折射率的传感特性.结果表明,外界环境折射率在1.333～1.4532之间变化时,同一直径倾斜光纤光栅的高阶包层模的敏感性要比低阶包层模强;随着包层直径的减小,包层模的敏感性增强,且在折射率比较高的环境中有更高的敏感性.因此,利用倾斜光纤光栅的温度特性不仅可以解决温度交叉敏感问题,而且通过小同的腐蚀程度能定制所需要的灵敏度,以实现对环境折射率的高灵敏度测量.该办法可应用于对生物和化学等高灵敏度传感领域的各种溶液进行实时监控.     

Coupling characteristics of photo-induced Bragg gratings in depressed- and matched-cladding fibre

Experimental transmission spectra of ultraviolet (u.v.)-written Bragg gratings in depressed- and matched-cladding fibre are characterized and compared. In particular, we discuss how the location and strength of the spectral features vary with the degree of blazing, or angular tilt of the grating. The fine-structure detail on the short-wavelength side of the fundamental Bragg line is attributed to power coupling between the forwardpropagating fundamental (LP₀₁) mode and discrete, backward-propagating cladding modes. Resonances corresponding to backward-propagating LP_0n and LP_1n modes are identified, and their relative strengths are compared with theoretical overlap calculations. Physical arguments are presented that explain the pronounced ghost-grating notch that appears in the transmission spectra of blazed, fibre Bragg gratings in depressed-cladding fibre.     

30 keV He~(2+)在不同倾斜角度的聚碳酸酯微孔膜中的传输过程

本文测量了30 keV的He~(2+)入射倾斜角度分别为-0.5~?,-1~?,-1.5~?和-2.5~?的聚碳酸酯纳米微孔膜后,出射粒子角度分布、电荷态分布以及相对穿透率随时间的演化.当微孔膜倾斜角度在-0.5~?,-1~?和-1.5~?时,出射的He~(2+)离子始终保持在入射束流方向,出射的He~0原子出射方向由微孔孔道方向逐渐转移到入射束流方向,在实验过程中观测到明显的电荷交换,这一现象与之前发现的导向效应不同,微孔内部沉积的电荷斑和微孔内表面原子的短程集体散射作用,克服入射离子的横向动量,使入射离子在微孔内表面以上以类似镜面掠射的方式出射,并发生时间演化效应,主要传输机制为电荷斑辅助的表面以上的类似镜面掠射行为.而当倾斜角度在-2.5~?时,出射的He~(2+)离子始终保持在入射束流方向,出射的He~0原子始终保持在微孔孔道方向,沉积的电荷斑很难克服入射离子的横向动量,没有时间演化效应,主要传输机制为微孔内表面以下的多次随机非弹性碰撞过程.这一物理图像使中能离子入射不同倾斜角度的微孔膜物理认识更加深入和完整.     

Analysis of spectral characteristics for reflective tilted fiber gratings of uniform periods

On the basis of the coupled-mode theory, a detailed investigation of the optical spectral characteristics is presented for uniform tilted fiber gratings. Explicit expressions are derived for the spectral parameters of reflection and transmission spectra. Numerical simulations are carried on to show the dependences of grating spectral responses on the structural parameters, such as tilt angle, grating length, index modulation amplitude and polarization states. The effects of these parameters on shaping the grating spectra are discussed comprehensively. The physical mechanism and intuitive phase-matching vector model are provided to explain the unique behaviors of transmission loss spectra. The results are helpful for providing a better understanding of the spectral behavior of the tilted fiber grating.     

Inscription and Visualization of Tilted Fiber Bragg Gratings

Tilted fiber Bragg gratings with different tilt angles have been inscribed in single-mode isotropic optical fiber with an increased photorefractivity using Talbot interferometer and KrF-excimer laser system. Their spectra are studied. Using a confocal laser scanning luminescent microscope the images of gratings in transmitted light were obtained. The calculated dependence of the slope angle of the grating recorded in the Talbot interferometer on the angle between the strokes of the interference pattern created in the interferometer and the transverse section of the optical fiber is experimentally verified.     

Novel B/Ge codoped photosensitive fibres and their dispersion compensation applications

A novel B/Ge codoped fibre was proposed, which also has photosensitive depressed inner cladding. The transmission spectrum of written grating in this fibre verified its strong photosensitivity and suppression of cladding mode coupling. After taking the diffraction into account, a more exact equation of the Bragg wavelength tuning theory of phase mask method was given. Then 8 cascaded fibre Bragg gratings centered at different wavelengths were successfully written with 248 nm KrF excimer laser and one piece of 1067 nm phase mask. By tilting the phase mask, chirp was also written in each grating. At last, it compensated the dispersion of 44 km single mode fibre in the 8 × 10 Gbit/s wavelength division multiplexing system successfully.     

Natural Convection from a Corrugated Heated Surface at the Bottom of Vented Rectangular Enclosure

Natural convection heat transfer characteristics enclosures from a tilted rectangular enclosure heated at the corrugated bottom wall and vented by uniform slots opening at the top wall are experimentally investigated. The experiments were carried out to study the effects of the angle of opening of the corrugated surface, opening ratio, enclosure's tilt angle, and Rayleigh number on the passive cooling of the enclosure. The experiments were carried out at Rayleigh numbers ranging from 2 × 10⁸ to 1.52 × 10⁹ for enclosure tilt angles ranging from 0° to 90° and angle of opening of corrugated surface ranging from 0° to 25°. The top venting arrangement was studied at different opening ratios of 1, 0.75, 0.5, and 0.25. The results gave an optimum angle of opening of the corrugated surface at which Nusselt number is maximum.     

Biochemical sensor based on a novel all-fibre cavity ring down spectroscopy technique incorporating a tilted fibre Bragg grating

A novel all-fibre cavity ring down spectroscopy technique is proposed where a tilt fibre Bragg grating (TFBG) or long-period grating (LPG) in the cavity provides sensitivity to surrounding medium. Such configuration with an LPG as the representative was theoretically analyzed. Two spectral bands were identified employable for sensing of surrounding refractive index for a weak LPG while only one band existed for a strong LPG. A TFBG, with enhanced sensitivity compared to usual LPGs, was used in a ring down cavity of 1 m constructed with 2 fibre Bragg gratings as the reflectors and the decay time changed from 220 to 450 ns when the TFBG was immersed into water from air.     

Brillouin fibre laser discrete sensor for simultaneous strain and temperature measurement

In this work, a Brillouin fibre laser sensor for strain and temperature discrimination is presented. The fibre laser sensor consists of a Fabry–Pérot cavity with 20 m of optical fibre between two Bragg gratings. For the strain measurement, the 20 m were split in half and in 10 m a pre-tension was applied originating two Brillouin peaks. For the temperature measurement all of the sensing head was heated. The resolutions achieved were ±1 με and ±1 °C for strain and temperature measurements, respectively. PACS 42.81.-I; 42.55.Wd; 42.65.Es     

A performance study of a nonlinear all Fibre Michelson interferometer,add-drop multiplexer,based in Fibre Bragg grating mirrors

In this paper we report a numerical investigation of an all-fibre narrowband transmission filter in the arrangement of two identical photo-imprinted Bragg gratings symmetrically located in each arm of a Michelson Interferometer, simulating, thus, an add-drop filter. The transmission characteristics and in addition the crosstalk level and extinction ratio, were studied. The coupled mode theory and the fourth-order Runge-Kutta method were applied, respectively, to solve the coupled differential equations. This is the first study, as far as we now, of the performance of this device considering the nonlinearity of the fibre coupler and linearity of the fibre Bragg gratings. The device is presenting a highly nonlinear behavior dependence in dephasing and pump power.     

Optimisation of superimposed chirped fibre Bragg gratings for the generation of ultra-high speed optical pulse bursts

Compact superstructure fibre Bragg gratings for the generation of ultra-high speed optical pulse bursts are reported. The gratings are equivalent in response to multi-pass superimposed chirped fibre Bragg gratings (SI-CFBGs), but an arbitrary sequence of consecutive gratings can be replicated in a single fabrication step using a simple trigonometric amplitude-phase function. SI-CFBGs are fabricated in photosensitive optical fibre and the time-resolved reflection of a 10 GHz picosecond pulse train is measured via frequency-resolved optical gating and optical sub-harmonic sampling detection techniques. The experimental results are compared to the theoretically simulated grating response and good agreement is found.     

Formation of misfit edge dislocations in Ge x Si1 ? x films ( x ～ 0.4–0.5) grown on tilted Si(001) → (111) substrates

The dislocation structure of Ge _x Si_{1 − x} films (x ∼ 0.4–0.5) grown by molecular epitaxy on Si(001) substrates tilted by 6° about the 〈011〉 axis was studied. It is shown that, in the tilt direction, edge misfit dislocations (MDs) arise only in the form of short segments lying on the intersections of 60° MDs. As a result, the total length of edge MDs along the substrate tilt direction is smaller than that along the tilt axis. The deviation of the substrate surface from the singular plane made it possible to detect a dislocation configuration that consists of a short segment of an edge MD and two diverging 60° MDs propagating from it in the tilt direction. The formation of the segment is assumed to begin with simultaneous nucleation of complementary dislocation half-loops that form a short edge MD on the interface and then propagate on one side as two diverging 60° MD lines. Original Russian Text ? Yu.B. Bolkhovityanov, A.K. Gutakovskii, A.S. Deryabin, L.V. Sokolov, 2008, published in Fizika Tverdogo Tela, 2008, Vol. 50, No. 10, pp. 1783–1787.     

Fabrication of a tilted fiber Bragg grating with a designed reflection spectrum profile

A method of fabricating a tilted fiber Bragg grating (TFBG) with a designed reflection spectrum profile is proposed and demonstrated experimentally. In a reflective TFBG the central wavelength and the reflectivity are dependent on the tilt angles. Controlling the rate at which the tilt angle is continuously varied and the exposure dose in the UV-light writing process permits accurate control of the bandwidth and reflectivity of the grating. The experimental result agrees well with TFBG theory and calculation.     

Reconfigurable WDM add/drop multiplexer based on optical switches and fibre Bragg gratings

A reconfigurable wavelength-division-multiplexing (WDM) add/drop multiplexer (WADM) is constructed using optical switches (OSWS) and fibre Bragg gratings (FBGs). Selected one or two channel(s) can be added/dropped at the same multiplexer by properly controlling the optical switch pair and fibre Bragg grating arrangement. Afour-channel system is experimentally demonstrated for a data rate of 2.5 Gb s–1 and a single-mode fibre (SMF) distance of 100km. A negligible maximum power penalty of only 0.3dB is observed when compared with back-to-back transmission.     

Temperature-insensitive 2-D tilt sensor by incorporating fiber Bragg gratings with a hybrid pendulum

A novel two-dimensional (2-D) tilt sensor is demonstrated by incorporating only two fiber Bragg gratings (FBGs) with a hybrid pendulum transducer. The pendulum transducer is specially designed with hollow half at the upper side and solid half at the lower side. Two FBGs were attached on the surface separated by one fourth of the circumference of the rod of pendulum and across the interface of its hollow and solid parts. Reflection peaks of FBGs split by the applied tilt angle. 2-D tilt angle can be determined by monitoring the wavelength separations of the split peak in two FBGs, which is inherently insensitive to temperature. In the experiment, a sensitivity of 0.054 nm/° over a wide range of 20º has been achieved, with the accuracy of 0.27°.     

双棱镜改变写入Bragg波长的相位掩模技术

将一种可旋转的双棱镜引入到相位掩模技术中以改变光栅的写入Bragg波长.在该系统中,光纤光栅是由来自可旋转双棱镜所形成的波长为248 nm的紫外干涉条纹写入的,其中,相位掩模被用作 1级衍射光的分束器,通过双棱镜的旋转可改变两写入光束的交叉角.为了初始化Bragg波长的参考值,双光栅的顶角由相位掩模的 1级衍射角和双棱镜的折射率确定.因为在～100 nm范围内两光束的非对称旋转对光栅周期的改变是5×10~(-4) nm,双棱镜引入的光栅的闪耀可忽略.当Bragg波长的移位为1 nm时,棱镜最大的旋转角为～1 degree,最小的旋转角是～2.4 min.与Talbot干涉仪中平面镜的旋转角～23 s/nm相比,该相位干涉仪中棱镜的旋转精度降低了2～3个数量级.     

Suppression of the interactions between fibre gratings used as dispersion compensators in dense wavelength-division multiplexing systems

Chirped fibre Bragg gratings (CFBGs) are required to be concatenated to compensate the fibre dispersion in the dense wavelength-division multiplexing (DWDM) systems. When the channel spacing is small, the performance of CFBGs is degraded, which restricts the usage of fibre gratings. The origin of the interactions between the gratings is analysed and methods of suppressing the interactions are also proposed.     

光纤Bragg光栅倾角传感器的标定与不确定度分析

实现光纤Bragg光栅倾角传感器的静态的测试和性能分析。设计了一种量程为5°的倾角传感器标定装置,对其进行校准实验。通过对光纤光栅解调仪的中心波长差和标定装置产生的倾角值进行最小二乘法拟合,求出静态标定系数,并对倾角传感器标定装置的不同不确定度分量进行分析以求出合成不确定度。实验结果表明,光纤传感器的灵敏度为0.17343nm/(°),线性度为99.993%,重复性误差为0.0552%,标定装置的合成不确定度为8.606×10-2°。