Comparison of MAHD with UAE and Hydrodistillation for the Analysis of Volatile Oil From Four Parts of Perilla frutescens Cultivated in Southern China

Three different isolation techniques, specifically microwave-assisted hydrodistillation (MAHD), ultrasound-assisted extraction (UAE), and conventional hydrodistillation (HD) were employed to obtain essential oils from whole plants, leaves, roots, and stems of Perilla frutescens. The essential oils were analyzed using gas chromatography with flame ionization detection and gas chromatography with mass spectrometry. Variations in chemical composition were observed; these were attributed to differences in plant organs. Variations in the percentages of the main constituents of the oils extracted based on plant organ were irregular and affected the quantity and composition of the oils. Oil yields were affected by the method of extraction and extraction organ variation. The maximum volume of oil was extracted from leaves via MAHD and the minimum was extracted from roots via UAE. Oil yields ranged from 0.05% to 0.53%. The contents of essential oil varied significantly with the plant organ. In the essential oils of the plant parts studied were showed a predominance of oxygenated monoterpenes. Variation of extraction methods and organs may influence the oil components either qualitatively or quantitatively.     

Comparison of microwave-assisted and conventional hydrodistillation in the extraction of essential oils from mango (Mangifera indica L.) flowers

Microwave-assisted hydrodistillation (MAHD) is an advanced hydrodistillation (HD) technique, in which a microwave oven is used in the extraction process. MAHD and HD methods have been compared and evaluated for their effectiveness in the isolation of essential oils from fresh mango (Mangifera indica L.) flowers. MAHD offers important advantages over HD in terms of energy savings and extraction time (75 min against 4 h). The composition of the extracted essential oils was investigated by GC-FID and GC-MS. Results indicate that the use of microwave irradiation did not adversely influence the composition of the essential oils. MAHD was also found to be a green technology.     

Comparative study of chemical composition,antibacterial and antioxidant activity of essential oils isolated from the seeds of Amomum subulatum by using microwave extraction and hydro-distillation methods

Microwave assisted hydro-distillation (MAHD) and conventional hydro-distillation (HD) techniques were compared in the extraction of essential oils from Amomum subulatum seeds. The time required for MAHD method (70 ​min) is lesser than that for HD method (4 ​h). There is a slight increase in the yield of extracted oil in MAHD method (3.35%) compared to HD (3%). Gas chromatography–mass spectrometry GC-MS results show that MAHD extracted essential oil was wealthier in oxygenated compounds. 1, 8-Cineole was found to be a major compound in case of both the essential oil, followed by α-pinene. In MAHD the percentage of the major oxygenated monoterpene (1, 8- cineol) slightly increases from 88% to 89% as compared to hydrodistillation. Contrarily to this, the percentage of monoterpene hydrocarbon was decreased in MAHD than HD extracted oil. MAHD and HD extracted oils show good antibacterial activities against gram-negative and gram-positive bacteria. MAHD extracted oil shows better antibacterial activity than HD extracted against both gram positive and gram-negative bacteria. 2, 2-diphenyl-1-picrylhydrazyl (DPPH•) radical scavenging antioxidant activities show that MAHD extract has better inhibition percentage than HD extract, and the half-maximal inhibitory concentration IC50 value of MAHD was less than HD extracted oil.     

A study on the essential oil of Ferulago campestris: How much does extraction method influence the oil composition?

The essential oil of different parts of Ferulago campestris (Bess.) collected in Sicily has been extracted by microwave-assisted hydrodistillation (MAHD) and by classic hydrodistillation (HD). A comparative qualitative-quantitative study on the composition of the oils was carried out. A total of 100 compounds were identified in the oils obtained by MAHD, whereas 88 compounds characterized the HD oils. The most prominent components were, in all different parts of F. campestris and in both extraction methods, 2,4,5-trimethylbenzaldehyde and 2,4,6-trimethylbenzaldehyde isomers; the latter was not previously found. The attempt to evaluate where the oil components are located in all parts of the plant was carried out by means of a kinetic study. Then, electron microscopy observation on the different parts before and after MAHD and HD was performed.     

Rapid analysis of the essential oils from dried Illicium verum Hook. f. and Zingiber officinale Rosc. by improved solvent-free microwave extraction with three types of microwave-absorption medium

A new method of extracting essential oils from dried plant materials has been studied. By adding a microwave-absorption medium (MAM) to a reactor, solvent-free microwave extraction (SFME) was improved and can be used to extract essential oils from dried plant material without pretreatment. With a microwave irradiation power of 85 W it took only approximately 30 min to extract the essential oils completely. The whole extraction process is simple, rapid, and economical. Three types of MAM, iron carbonyl powder (ICP), graphite powder (GP), and activated carbon powder (ACP), and two types of dried plant material, Illicium verum Hook. f. and Zingiber officinale Rosc., were studied. The results were compared with those obtained by use of conventional SFME, microwave-assisted hydrodistillation (MAHD), and conventional hydrodistillation (HD), and the conclusion drawn was that improved SFME was a feasible means of extracting essential oils from dried plant materials, because there were few differences between the composition of the essential oils extracted by improved SFME and by the other methods.     

Optimization of microwave-assisted hydro-distillation essential oil extracted from Rumex Crispus leaves using definitive screening design

Conversion of nonfood natural products to value-added products is an important work, which is going on worldwide. In addition, to obtain a product with better quality, a sufficient separation method is helpful to improve its utilization value by using effective, rapid and environmentally friendly techniques. Thus in this work, the microwave-assisted hydrodistillation (MAHD) process of essential oils from important natural plant Rumex Crispus leaves was investigated. The experimental design and extraction conditions were optimized using a definitive screening design. The yield of essential oils of 4.67 ± 0.02 % was investigated under the optimum conditions; 534.89 W of microwave power, 23.48 min of hydrodistillation time and 4.5 mL/g of the volume of water to plant mass ratio. Under these conditions, the essential oils were analyzed using gas chromatography-mass spectrometry (GC–MS). Results revealed that the essential oil extracted by MAHD possessed high quality as proved by its higher percentage of oxygenated compounds. In addition, α-santol (29.63 %) and β-santol (25.60 %) are the primary components of oxygenated compounds in essential oils. In conclusion, the MAHD was successfully employed to obtain mainly Oxygenated compounds-rich essential oil that may be used in several industrial applications. Subsequently, a definitive screening design may be regarded as an alternative and reliable method for the prediction of experimental parameters. It was concluded that the weeds plant (Rumex Crispus) contains a reliable quantity of oils that is extremely feasible to use and recommended as good feedstock for possible use in industrial applications.     

Rapid Extraction of Essential Oil from Dried Cinnamomum cassia Presl and Forsythia suspensa(Thunb.)Vahl by Ionic Liquid Microwave Extraction

Ionic liquid (IL) was used as the microwave absorption medium to extract essential oils from dried Cinnamomum cassia Presl and Forsythia suspensa (Thunb.) Vahl, and the ionic liquid microwave extraction (ILME) was developed. Some experimental parameters for ILME were examined. The proposed method was compared with other methods, including hydrodistillation (HD), microwave hydrodistillation (MHD), solvent‐free microwave extraction (SFME) and improved solvent‐free microwave extraction (ISFME). Experimental results showed that compared with other extraction methods the ILME had some advantages, such as time‐saving, simplicity and usage of green solvents. The extraction time was less than 18 min at the microwave power of 440 W and 1.5 mL of ionic liquid was required. The constituents of essential oils obtained by the five methods are not obviously different.     

A comparison between different techniques for the isolation of rosemary essential oil

Traditional hydrodistillation (HD), supercritical fluid extraction (SFE), organic solvent extraction (SE), and water microwave assisted hydrodistillation (MAHD) techniques were compared and evaluated for their effectiveness in the isolation of rosemary essential oil. The microwave assisted hydrodistillation technique was optimized in terms of both delivered power and time duration. The extracts/distillates were analyzed by GC and GC-MS. Microwave distillation, which exploits the physical action of microwaves on plants, showed a series of advantages over the other approaches: low cost, use of water in sample pre-treatment step, greatly reduced isolation time, and attainment of high quality essential oil distillate. Moreover, the absence of environmental impact of this innovative technique was also emphasized.     

Composition and antioxidant activity of Thymus vulgaris volatiles: Comparison between supercritical fluid extraction and hydrodistillation

Supercritical fluid extraction (SFE) of the volatile oil from Thymus vulgaris L. aerial flowering parts was performed under different conditions of pressure, temperature, mean particle size and CO₂ flow rate and the correspondent yield and composition were compared with those of the essential oil isolated by hydrodistillation (HD). Both the oils were analyzed by GC and GC‐MS and 52 components were identified. The main volatile components obtained were p‐cymene (10.0–42.6% for SFE and 28.9–34.8% for HD), γ‐terpinene (0.8–6.9% for SFE and 5.1–7.0% for HD), linalool (2.3–5.3% for SFE and 2.8–3.1% for HD), thymol (19.5–40.8% for SFE and 35.4–41.6% for HD), and carvacrol (1.4–3.1% for SFE and 2.6–3.1% for HD). The main difference was found to be the relative percentage of thymoquinone (not found in the essential oil) and carvacryl methyl ether (1.0–1.2% for HD versus t?0.4 for SFE) which can explain the higher antioxidant activity, assessed by Rancimat test, of the SFE volatiles when compared with HD. Thymoquinone is considered a strong antioxidant compound.     

Non-polar Solvent Microwave-Assisted Extraction of Volatile Constituents from Dried Zingiber Officinale Rosc.

A new method, non-polar solvent microwave-assisted extraction （NPSMAE）, was applied to the extraction of essential oil from Zingiber officinale Rosc. in closed-vessel system. By adding microwave absorption mediumcarbonyl iron powders （CIP） into extraction system, the essential oil was extracted by the non-polar solvent （ether） which can be heated by CIP. The constituents of essential oil obtained by NPSMAE were comparable with those obtained by hydrodistillation （HD） by GC-MS analysis, which indicates that NPSMAE is a feasible way to extract essential oil from dried plant materials. The NPSMAE took much less extraction time （5 min） than HD （180 min）, and its extraction efficiency was much higher than that of conventional polar solvent microwave-assisted extraction （PSMAE） and mixed solvent microwave-assisted extraction （MSMAE）. It can be a good alternative for the extraction of volatile constituents from dried plant samples.     

Supercritical fluid extraction of the volatile oil from Santolina chamaecyparissus

Supercritical fluid extraction (SFE) of the volatile oil from Santolina chamaecyparissus L. flower heads was performed under different conditions of pressure, temperature, mean particle size and CO₂ flow rate. This oil was compared with the essential oil isolated by hydrodistillation (HD). The SFE volatile and essential oils were analysed by GC and GC‐MS. The range of the main volatile components obtained with HD and SFE were, respectively: 1,8‐cineole (25–30% and 7–48%), camphor (7–9% and 8–14%), borneol (7–8% and 2–11%), terpinen‐4‐ol (6–7% and 1–4%), terpinolene (1–4% and 1–7%) and isobornyl acetate (1–2% and 1–11%). The chemical composition of the extracts was greatly influenced by the conditions of pressure and temperature used. In fact, it was possible to enrich the sesquiterpene fraction by increasing the pressure from 8 to 9 MPa, while changing the temperature from 40 to 50°C at 90 bar enriched of the volatiles in n‐alkanes.     

A Comparative Study of Hydrodistillation and Hydrodistillation–Solvent Microextraction Methods for Identification of Volatile Components of Echinophora cinerea

A recently developed hydrodistillation–solvent microextraction (HD–SME) method coupled to gas chromatography–mass spectrometry (GC–MS) was applied to the analysis of volatile components of aerial parts of Echinophora cinerea (Boiss). By the use of a simplex optimization method, the effects of extraction time, sample weight and microdrop volume on the extraction efficiency of the method were optimized. In the optimized conditions, 3 µL of n-heptadecane was suspended in the headspace of 6 g of hydrodistillating sample, using a microsyringe. After 7 min, the solvent was retracted back into the syringe and directly injected into the GC–MS injection port. The HD–SME method was compared to a conventional hydrodistillation technique. In general, the extraction with HD–SME was relatively faster and required smaller amounts of sample. The microextraction method also showed some selectivity towards α-phellandrene and Z-β-ocimene monoterpenes. A precision better than 6.5% (expressed as relative standard deviation) was obtained for the method.

     

Antioxidant activity of crude extracts and essential oils from flower buds and leaves of Cistus creticus and Cistus salviifolius

Volatile oils from flowers and leaves of C. creticus L. and C. salviifolius L. were extracted by two extraction methods; namely, hydrodistillation and solid-phase micro-extraction (SPME). The chemical composition of essential oils was analyzed by GC and GC–MS. The volatile extracted from leaves and flowers of C. criticus using SPME was dominated by monoterpenes and sesquiterpenes hydrocarbon with α-pinene, camphene and α-cubebene as major components. In hydrodistillation, the oil extracted from leaves was dominated by oxygenated diterpenes and diterpenes hydrocarbon with manoyl oxide and sclarene as major components, whereas, the oil extracted from flowers was dominated by oxygenated diterpenes and diterpenes hydrocarbon with manoyl oxide and abietatriene as major components. The volatile from flowers and leaves of C. salviifolius obtained by SPME were dominated by monoterpenes and sesquiterpenes with δ-3-carene, α-pinene, β-pinene, and E-caryophyllene as major constituents. On the other hand, the oils from flowers and leaves of C. salviifolius obtained by hydrodistillation were dominated by oxygenated diterpenes, diterpenes hydrocarbon and esters with dehydro abietol, abietol, manoyl oxide and methyl octadecenoate as major components. In the leaves, the major components of the oil were manoyl oxide, E-ethyl cinnamate, and Z-ethyl cinnamate. These oils showed weak antioxidant activity when compared to the positive controls α-tocopherol, ascorbic acid, and EDTA, while the crude extracts aq. MeOH, butanol, and water showed good antioxidant activity. Discriminating between the studied plants based on the extraction method was also possible upon applying Principle component analysis (PCA) to the obtained GC–MS data.     

Microwave extraction of essential oils from dried fruits of Illicium verum Hook. f. and Cuminum cyminum L. using ionic liquid as the microwave absorption medium

Ionic liquid was used as microwave absorption medium and applied to the extraction of essential oils from dried fruits of the Illicium verum Hook. f. and Cuminum cyminum L. by microwave‐assisted extraction. The extraction time is less than 15 min at the microwave power of 440 W. The constituents of essential oils obtained by the proposed method were compared with those obtained by hydrodistillation. There is no obvious difference in the constituents of essential oils obtained by the two methods.     

微波提取对挥发油化学成分的影响

采用无溶剂微波辅助提取与微波水蒸气蒸馏法提取薄荷叶和花椒挥发油,气相色谱-质谱(GC-MS)分析挥发油化学成分,与传统的水蒸气蒸馏对比,考察了微波对挥发油化学成分的影响.结果表明,微波促使薄荷叶挥发油中的薄荷醇氧化,转变为长叶薄荷酮和少量的薄荷呋喃酮.花椒挥发油中的按油素等化合物受质子的催化,在长时间温度较高的提取条件...     

Improved solvent-free microwave extraction of essential oil from dried Cuminum cyminum L. and Zanthoxylum bungeanum Maxim

Solvent-free microwave extraction (SFME) is a recently developed green technique which is performed in atmospheric conditions without adding any solvent or water. SFME has already been applied to extraction of essential oil from fresh plant materials or dried materials prior moistened. The essential oil is evaporated by the in situ water in the plant materials. In this paper, it was observed that an improved SFME, in which a kind of microwave absorption solid medium, such as carbonyl iron powders (CIP), was added and mixed with the sample, can be applied to extraction of essential oil from the dried plant materials without any pretreatment. Because the microwave absorption capacity of CIP is much better than that of water, the extraction time while using the improved SFME is no more than 30 min using a microwave power of 85 W. Compared to the conventional SFME, the advantages of improved SFME were to speed up the extraction rate and need no pretreatment. Improved SFME has been compared with conventional SFME, microwave-assisted hydrodistillation (MAHD) and conventional hydrodistillation (HD) for the extraction of essential oil from dried Cuminum cyminum L. and Zanthoxylum bungeanum Maxim. By using GC-MS system the compositions of essential oil extracted by applying four kinds of extraction methods were identified. There was no obvious difference in the quality of essential oils obtained by the four kinds of extraction methods.     

GC Comparative Analysis of Leaf Essential Oils from Two Myrtle Varieties at Different Phenological Stages

The essential oils obtained from leaves of two Myrtus communis varieties (baetica and italica), growing wild in North Tunisia, were investigated by GC and GC–MS at their different phenological stages. The highest essential oil yield was observed at the flowering stage with 0.6% (w/w) for italica and 0.4% (w/w) for baetica and 49 compounds were identified. The main essential oil leaf compounds of both myrtle varieties, belonging to the monoterpene class, were α-pinene, 1,8-cineole, limonene and linalool and their percentages showed significant changes during the phenological stages.

     

Enrichment of the thymoquinone content in volatile oil from Satureja montana using supercritical fluid extraction

Supercritical fluid extraction (SFE) of the volatile oil from Satureja montana L. was performed under different conditions of pressure (90 and 100 bar), temperature (40 and 50°C), mean particle sizes (0.4, 0.6 and 0.8 mm) and CO₂ flow rate (0.8, 1.1 and 1.3 kg/h) to understand the influence of these parameters on the composition and yield of this oil. The results were compared with those obtained for the essential oil isolated by hydrodistillation (HD). The volatile and the essential oil were analysed by GC and GC‐MS. The main compounds are carvacrol (52.2–62.0% for HD vs. 41.7–64.5% for SFE), thymol (8.6–11.0% for HD vs. 6.0–11.3% for SFE), p‐cymene (6.9–12.8% for HD vs. 6.0–17.8% for SFE), γ‐terpinene (6.4–9.4% for HD vs. 2.3–6.0% for SFE) and β‐bisabolene (2.0–2.7% for HD vs. 2.2–3.5% for SFE). The major difference between SFE and HD was the relative amount of thymoquinone, an oxygenated monoterpene with important biological activities, which can be ten‐fold higher in volatile oil (1.6–3.0 for SFE vs. 0.2% for HD). The morphology of the glandular trichomes of S. montana and the effect of the grinding process on them was also evaluated by SEM.     

Reporting effective extraction methodology and chemical characterization of bioactive components of under explored Platycladus orientalis (L.) Franco from semi-arid climate

The bioactive ingredients of many essential oils are complex and difficult to reproduce synthetically. In the present study, the influence of extraction method on relative extraction of bioactive compounds of essential oil of Platycladus orientalis (L.) Franco (Thuja orientalis L. is a synonym of it) leaves gathered from semi-arid climate was studied. A higher yield of essential oil was obtained by hydrodistillation (0.1%) as compared to steam distillation (0.07%) under newly optimized conditions. Initial analysis of these oils by TLC showed the presence of different polarity groups ranging from non-polar terpene hydrocarbons to polar terpenoid alcohols. GC-MS analysis revealed that major component of hydrodistilled essential oil of Platycladus orientalis (L.) Franco leaves was α-pinene (17.83%) and steam distilled essential oil contained α-cedrol (12.44%). The results obtained in the present study emphasize that suitable extraction technique should be used to obtain particular component of interest.     

Antibacterial activity and comparison of the volatile constituents obtained by several extraction methods from the flowers, stems and leaves of Astrodaucus orientalis

The oils of the flowers, stems and leaves of Astrodaucus orientalis L. were separately extracted using hydrodistillation (HD), head-space solid-phase microextraction (HS-SPME) and microwave assisted head-space solid-phase microextraction (MA-HS-SPME). The volatile constituents were analyzed by GC and GC/MS. Temperature and time of extraction, microwave power and exposure time of extraction were optimized. Polydimethylsiloxane (PDMS) fiber was used as the solid phase for SPME methods. The main constituents of the flower, stem and leaf oils isolated by HD, HS-SPME and MA-HS-SPME are as follows, respectively: beta-pinene (20.5%, 13.9% and 30.4%), alpha-thujene (8.7%, 16.2% and 10.9%) and alpha-pinene (7.6%, 14.3% and 10.9%) for the flowers, sabinene (11.8%, 32.3% and 11.8%), alpha-pinene (8.7%, 28.8% and 6.1%) and p-mycrene (2.5%, 12% and 8.5%) for the stem, and alpha-pinene (9.4%, 37.1% and 22.5%), sabinene (13.5%, 26.3% and 23.5%), beta-pinene (6.3%, 9.8% and 10%) and p-mycrene (3.2%, 2.5% and 15.6%) for the leaf. The minimum inhibitory concentrations (MIC) were determined for all essential oils obtained by HD against both Gram-positive (Bacillus subtilis) and Gram-negative (Escherichia coli) bacteria using the agar dilution method. These oils showed the good activities against the both bacteria (0.5 - 1.5 mg/mL).