Reactivity ratios for copolymerization of vinyl chloride with 2-methylpentyl vinyl brassylate by computerized linearization

A computerized version of the Fineman-Ross linearization procedure was used to determine reactivity ratios for copolymerization of vinyl chloride (monomer 1) and 2-methylpentyl vinyl brassylate (monomer 2). From differential refractometry data for the products of low-conversion copolymerization, the procedure gave r₁ = 1.06 and r₂ = 0.234. The ratios computed from chlorine contents of the same products were r₁ = 1.10 and r₂ = 0.239. The polarity factor (e₂) and general monomer reactivity (Q₂) calculated for monomer 2 from these ratios were, respectively, ?0.95 to ?0.98 and 0.032–0.033. The interquartile range for the copolymerization of a mixture of 60% monomer 1 and 40% monomer 2 was 1.4%. These values suggest that from suitable proportions of reactants, sufficiently homogeneous distribution of monomers can be achieved in copolymers of vinyl chloride and 2-methylpentyl vinyl brassylate to offer the possibility of effective internal plasticization.     

Reactivities and NMR spectra of vinyl ethers

Copolymerizations of n-butyl vinyl ether (M₁) with other vinyl ethers were carried out in toluene at ?78°C with EtAlCl₂ catalyst and the monomer reactivity ratios were determined. It was found that the relative reactivity of alkyl vinyl ether log 1/r₁ is higher when the alkyl group is more electron-donating and the reactivity correlates linearly with the Taft σ^* of alkyl group in the monomer. The NMR spectra of vinyl ethers and of vinyl ether–trialkylaluminum complexes were investigated. Close correlations were found between the spectral characteristics and the relative reactivity of vinyl ether in the copolymerization. The degree of resonance contribution in alkyl vinyl ether was also discussed on the basis of NMR data.     

Vinyl‐Type Polymerization of Norbornene Dicarboxylic Acid Dialkyl Esters

Summary: Poly(cis‐norbornene‐exo‐2,3‐dicarboxylic acid dialkyl esters) (alkyl = Me, Et, Pr, Bu, Pen, and Hex) are synthesized as a vinyl‐type with a palladium(II ) catalyst in high yield from easily prepared, pure exo‐monomers. The polymers show good solubility in common organic solvents and excellent thermal stability up to 330 °C. The polymers with alkyl groups larger than methyl exhibit a two‐step thermal degradation profile of an initial thermal degradation of side‐chains starting at 350 °C, followed by thermal degradation of the norbornene backbone starting at ca. 430 °C. The glass transition temperature decreases and the mechanical flexibility increases as the alkyl length of the side‐chain increases.

Normalized loss shear modulus (G″) versus temperature for polynorbornene dicarboxylic acid dialkyl esters.     

Stereospecific polymerization of isobutyl vinyl ether catalyzed by calcined iron sulfate

The polymerization of isobutyl vinyl ether was studied in a heterogeneous system using iron (II) sulfate calcined in air at various temperatures as a catalyst. The maximum activity was shown by the catalyst calcined at 700°C, which effected the polymerization at room temperature in a few seconds, while the sulfate treated at 750°C was totally inactive. Poly(vinyl ethyl ether) was also obtained by the FeSO₄ (700°C) catalyst at room temperature. This catalyst formed the crystalline polymer (melting temperature 135–138°C) when the reaction was performed in toluene as solvent at room temperature. Poisoning experiments with Hammett indicators were carried out with the FeSO₄ (700°C) catalyst. The treatment with n-butylamine rendered it inactive in the reaction of isobutyl vinyl ether, while its catalytic activity was little affected by dicinnamalacetone. On the basis of the observed results, the nature of active sites of catalyst is discussed.     

Polymerization of 2,2,2-trifluoroethyl vinyl ether

The polymerization of 2,2,2-trifluoroethyl vinyl ether by six different catalyst systems was examined. Low-temperature studies (?78°C) with boron trifluoride etherate catalyst in hydrocarbon and chlorinated solvents slowly yielded low molecular weight polymers which were amorphous and noncrystallizable upon cold drawing. Under similar conditions, polymerizations with boron trifluoride gas were spontaneous, quantitative, and gave relatively high molecular weight, form-stable, amorphous polymer. Heterogeneous polymerizations with chromium trioxide crystals in toluene at 68°C and bulk reactions with ethylmagnesium bromide–carbon tetrachloride catalyst at 40°C failed to produce polymer. Room temperature runs with triisobutylaluminum–titanium tetrachloride catalyst gave amorphous, tacky material. Aluminum hexahydrosulfate heptahydrate (AHS) initiated polymerizations conducted at 25 and 60°C gave low yields of mixtures of amorphous and crystalline polymers, the ratio depending upon the polymerization solvent employed. The infrared spectra and x-ray diffraction intensity curves of crystalline and amorphous poly(trifluoroethyl vinyl ether) are reported and compared herein for the first time.     

Synthesis and characterization of optically active poly(2-phenylvinyl alkyl ethers) and corresponding monomers

cis-(S) (+)-2-phenylvinyl alkyl ethers having as alkyl groups 1-methylpropyl (I), 2-methylbutyl (II), and 3-methylpentyl (III) were synthesized by condensation of phenylacetylene with the corresponding sodium alcoholates. Polymerization of monomers was performed cationically with BF₃ · Et₂O or SnCl₄ in toluene or CH₂Cl₂. Specific rotations of polymers were compared with those of low molecular weight model compounds prepared by hydrogenation of monomers, and it was concluded that the difference in the rotation of poly I and model compound ([α]_D 19.3° and 5.68°, respectively) and poly II and model compound ([α]_D 11.4° and 3.00°, respectively) can be attributed to the asymmetric induction at carbon atoms of the principal polymer chain.     

Synthesis and properties of Alkyl α-D-Galactopyranoside

Alkyl α-D-galactopyranosides are sugar-based nonionic surfactants, and it is necessary to research their structure–property relationships since it is not quite clear that the change of the alkyl chain length has effects on a series of physicochemical properties. Here, alkyl α-D-galactopyranosides were prepared by galactose and alcohols through three steps including acetylation, coupling with alcohols in the presence of a catalyst stannic chloride, and deprotection. Furthermore, their water solubility and other properties were investigated. Alkyl α-D-galactopyranosides (4a ～ 4e, n = 6 ～ 10) were water soluble, and their dissolution process in water was an endothermic process. Nonyl α-D-galactopyranoside (4d) showed excellent foaming ability and foam stability. Octyl α-D-galactopyranoside (4c) had the strongest emulsifying ability for toluene and nonyl α-D-galactopyranoside (4d) had the strongest emulsifying ability for rapeseed oil. The critical micelle concentration (CMC) values and surface tension at the CMC were decreasing with increasing alkyl chain length. Their standard free energy of adsorption (ΔG_ads) was more negative than their standard free energy of micellization (ΔG_mic). The moisture-absorption abilities were weakening with increasing alkyl chain length. Alkyl α-D-galactopyranosides (4a ～4f) were thermally stable below 280°C. Alkyl α-D-galactopyranosides (4c ～4f) had the optical texture of the thermotropic liquid crystal smectic A phase.     

Pyrolysis of waste tyres: The influence of USY catalyst/tyre ratio on products

In this paper, an ultrastable Y-type (USY) zeolite was investigated with two-staged pyrolysis–catalysis of waste tyres. Waste tyres were pyrolysed in a fixed bed reactor and the evolved pyrolysis gases were passed through a secondary catalytic reactor. The main objective of this paper was to obtain high concentration of certain aromatic hydrocarbons suitable to be used as a chemical feedstock rather than a liquid fuel, and the influence of catalyst/tyre ratio on the product yield and composition of derived oils. The light fraction (boiling point < 220 °C) was distilled from the derived oil prior to be analyzed with gas chromatography/mass spectrometry (GC/MS). It showed that the increase of catalyst/tyre ratio resulted in high yield of gas at the expense of the oil yield. The high catalyst/tyre ratio favored to increase the concentration of light fraction (<220 °C) in oil. Increasing the catalyst/tyre ratio resulted in significant changed in the concentration of benzene, toluene, xylenes and the alkyl aromatic compounds. For benzene and toluene, the highest concentration was obtained at the catalyst/tyre ratio of 0.5. The concentration of xylenes increased with the increasing of catalyst/tyre ratio.     

Supramolecular hydrogen-bonded liquid–crystalline polymer complexes. Design of side-chain polymers and a host–guest system by noncovalent interaction

Supramolecular liquid–crystalline polymeric complexes based on a backbone that contains vinyl pyridine units and azobenzene or biphenyl derivatives that posses alkyl chains terminated by carboxylic acid have been obtained by the formation of intermolecular hydrogen bonds between the carboxylic acid and the pyridyl moieties. The polymeric complexes behave as side-chain liquid–crystalline polymers and exhibit smectic phases. A new type of H-bonded host-guest liquid–crystalline system is also reported. The liquid–crystalline host copolymers contain both mesogenic acrylate and 4-vinylpyridine units. The guest molecule is an azobenzene that has a carboxylic acid moiety at one of its extremities. The H-bonded polymeric host–guest complexes exhibit nematic phases. Sequential UV and visible light irradiation of the polymeric complex causes reversible photochemically induced phase transitions. The isothermal nematic–isotropic and isotropic–nematic transitions result from the trans-cis and cis-trans photoisomerization of the guest azobenzene in the host–guest system. © 1996 John Wiley & Sons, Inc.     

Living cationic polymerization of ethyl 2-(vinyloxy)ethoxyacetate: A vinyl ether with an ether and an ester function in the pendant

Ethyl 2-(vinyloxy)ethoxyacetate ( 4 ; CH₂?CH? OCH₂CH₂OCH₂? COOC₂H₅), a vinyl ether having both carboxylic acid ester and oxyethylene unit in its pendant, afforded well-defined living polymers when polymerized by the hydrogen iodide/iodine (HI/I₂) initiating system in toluene at ?40°C. The polymers possessed a narrow molecular weight distribution (M _w/M _n ≤ 1.15), and their molecular weight (M _n) increased proportionally to monomer conversion or the molar ratio of the monomer to hydrogen iodide. The polymer molecular weight also increased upon addition of a fresh feed of the monomer to a completely polymerized reaction mixture. Polymers of high molecular weights (M _n > 5 × 10⁵) and broad molecular weight distributions were obtained by BF₃OEt₂ in toluene at ?40°C. Polymerization rate of 4 with HI/I₂ is ca. 100 times greater than that of the corresponding alkyl vinyl ether, and thus 4 was found to be one of the most reactive vinyl ethers thus far studied. Alkaline hydrolysis of the pendant ester groups of the polymers gave a vinyl ether-based polymeric carboxylic acid 6 with a narrow molecular weight distribution.     

Stereoregulation in cationic polymerization by designed Lewis acids. II. Effects of alkyl vinyl ether structure

Stereoregulation in the cationic polymerization of various alkyl vinyl ethers was investigated with bis[(2,6‐diisopropyl)phenoxy]titanium dichloride ( 1 ; catalyst) in conjunction with the HCl adduct of isobutyl vinyl ether as an initiator in n‐hexane at −78 °C. The tacticities depended on the substituents of the monomers. Isobutyl and isopropyl vinyl ethers gave highly isotactic polymers (mm = 83%), whereas tert‐butyl and n‐butyl vinyl ethers resulted in lower isotactic contents (mm ∼ 50%) similar to those for TiCl₄, a conventional Lewis acid, thus indicating that the steric bulkiness of the substituents was not the critical factor in stereoregulation. A statistical analysis revealed that the high isospecificity was achieved not by the chain end but by the catalyst 1 or the counteranion derived therefrom. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1060–1066, 2001     

Experimental and computational studies of ring‐opening polymerization of ethylene brassylate macrolactone and copolymerization with ε‐caprolactone and TBD‐guanidine organic catalyst

The ring‐opening polymerization (ROP) of ethylene brassylate, catalyzed by the cyclic guanidine 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD) is reported. Several experimental parameters were evaluated for bulk ROP process and polyesters, resulting in molecular weights between 3 and 15 kg mol^?1. End‐group analysis by ¹H nuclear magnetic resonnance (NMR) and matrix assisted laser desorption ionization time of flight computational studies supports the dual behavior of TBD, which can act as both a catalyst and initiator of the polymerization process. Under optimum conditions, semicrystalline poly(ethylene brassylate‐co‐ε‐caprolactone) random copolymers were synthesized. Depending on the comonomer content, our results showed a range of melting temperatures between 39 and 69 °C. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 552–561     

The effect of solvents on asymmetric induction cationic copolymerization of l-menthyl vinyl ether with indene

Cationic copolymerization of l-menthyl vinyl ether (l-MVE) with indene (IN) was carried out in several solvents with BF₃OEt₂ as catalyst at 0°C. The solvents used in this study were selected toluene (Tol), chloroform (CHCl₃), chlorobenzene (BzCl), 1,2-dichloroethane (EtCl₂), and nitrobenzene; (BzNO₂)/Tol = 65/35 mixture solvent. l-Methyl residue, which is an optically active side chain of copolymer produced by cationic copolymerization, was removed with dry hydrogen bromide gas by ether cleavage reaction. The copolymer [vinyl alcohol(VA)–lN], produced by the ether cleavage reaction, also showed optical rotation. From this result, therefore, it was concluded that asymmetric induction takes place in the copolymer main chain. The efficiency of asymmetric induction was determined by the measurement of optical rotation of VA–IN copolymer after the ether cleavage reaction. The efficiency of asymmetric induction in the copolymer main chain developed from the variation on polymerization solvents; the order was Tol > EtCl₂ > BzCl > CHCl₃ > BzNO₂/Tol (65/35) mixture solvent.     

An Expedient Phase Transfer Catalyst‐Mediated Synthesis of 2‐Alkyl/Aryl‐1,8‐phenanthrolines

Several 2‐alkyl and 2‐aryl‐1,8‐phenanthrolines were synthesized efficiently from 5‐aminoisoquinoline and seven α,β‐unsaturated aldehydes in aq. HCl–toluene mixture at 100°C using benzyltriethylammonium chloride as a phase transfer catalyst.     

Pyrrole-Protected β-Aminoalkylzinc Reagents for the Enantioselective Synthesis of Amino-Derivatives

Chiral β-aminoalkylzinc halides were prepared starting from optically pure commercial β-amino-alcohols. These amino-alcohols were converted to the corresponding N-pyrrolyl-protected alkyl iodides which undergo a zinc insertion in the presence of LiCl (THF, 25 °C, 10–90 min). Subsequent Negishi cross-coupling or acylation reactions with acid chlorides produced amino-derivatives with retention of chirality. Diastereoselective CBS-reductions of some prepared N-pyrrolyl-ketones provided 1,3-subsituted N-pyrrolyl-alcohols with high diastereoselectivity. Additionally, a deprotection procedure involving an ozonolysis allowed the conversion of the pyrrole-ring into a formamide without loss of optical purity.     

Flow Friedel–Crafts alkylation of 1-adamantanol with arenes using HO-SAS as an immobilized acid catalyst

In this communication flow Friedel–Crafts alkylation was studied using hydroxy-substituted sulfonic acid-functionalized silica as a catalyst and 1-adamantanol as a model substrate. The reaction of 1-adamantanol ( 1a ) with toluene ( 2a ) proceeded well with 5 min of residence time at 120°C to give good yield of 1-tolyladamantane ( 3a ) as a 1:9 mixture of meta and para isomers. When the flow synthesis was carried out over 2.5 hr of running time, the collected five fractions contain the product 3a in 97–92% yields, suggesting the durability of the catalyst.     

Stereoregularity of poly(vinyl ether)

α-Methylvinyl isobutyl and methyl ethers were polymerized cationically and the structure of the polymers was studied by NMR. Poly(α-methylvinyl methyl ether) polymerized with iodine or ferric chloride as catalyst was found to be almost atactic, whereas poly(α-methylvinyl isobutyl ether) polymerized in toluene with BF₃OEt₂ or AlEt₂Cl as catalyst was found to be isotactic. In both cases, the addition of polar solvent resulted in the increase of syndiotactic structure as is the case with polymerization of alkyl vinyl ether. tert-Butyl vinyl ether was polymerized, and the polymer was converted into poly(vinyl acetate), the structure of which was studied by NMR. A nearly linear relationship between the optical density ratio D₇₂₂/D₇₃₆ in poly(tert-butyl vinyl ether) and the isotacticity of the converted poly(vinyl acetate) was observed.     

Investigations on poly(vinyl chloride). II. Pyrolysis of chlorinated polybutadienes as model compounds for poly(vinyl chloride)

The pyrolysis of chlorinated polybutadienes (CPB) was investigated by using a pyrolysis gas chromatograph. CPB corresponds to poly(vinyl chloride) (PVC) constructed with head–head and tail–tail linkages of the vinyl chloride unit. Benzene, toluene, ethyl-benzene, o-xylene, styrene, vinyltoluene, chlorobenzenes, naphthalene, and methylnaphthalenes were detected in the pyrolysis products from CPB above 300°C, and no hydrocarbons could be detected at 200°C. The pyrolysis products from CPB were similar to those from PVC and new products could not be detected. Lower aliphatics, toluene, ethylbenzene, o-xylene, chlorobenzenes, and methylnaphthalenes were released more easily from pyrolysis of CPB than from PVC; amounts of benzene, styrene, and naphthalene formed were small. These results support the conclusion that recombination of chlorine atoms with the double bonds in the polyene chain takes place and that scission of the main chain may depend on the location of methylene groups isolated along the polyene chain during the thermal decomposition of PVC.     

Living cationic polymerization of n‐butyl propenyl ether

Cationic polymerization of n‐butyl propenyl ether (BuPE; CH₃CH CHOBu, cis/trans = 64/36) was examined with the HCl–IBVE (isobutyl vinyl ether) adduct/ZnCl₂ initiating system at −15 ∼ −78 °C in nonpolar (hexane, toluene) and polar (dichloromethane) solvents, specifically focusing on the feasibility of its living polymerization. In contrast to alkyl vinyl ethers, the living nature of the growing species in the BuPE polymerization was sensitive to polymerization temperature and solvent. For example, living cationic polymerization of IBVE can be achieved even at 0 °C with HCl–IBVE/ZnCl₂, whereas for BuPE whose β‐methyl group may cause steric hindrance ideal living polymerization occurred only at −78 °C. Another interesting feature of this polymerization is that the polymerization rate in hexane is as large as in dichloromethane, much larger than in toluene. A new method in determining the ratio of the living growing ends to the deactivated ones was developed with a devised monomer‐addition experiments, in which IBVE that can be polymerized in a living fashion below 0 °C was added to the almost completely polymerized solution of BuPE. The amount of the deactivated chain ends became small in hexane even at −40 °C in contrast to other solvents. Thus hexane turned out an excellent solvent for living cationic polymerization of BuPE. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 229–236, 2000     

Star‐shaped cyclopolymers: A new category of star polymer with rigid cyclized arms prepared by controlled cationic cyclopolymerization and subsequent microgel formation of divinyl ethers

The combination of living/controlled cationic cyclopolymerization and crosslinking polymerization of bifunctional vinyl ethers (divinyl ethers) was applied to the synthesis of core‐crosslinked star‐shaped polymers with rigid cyclized arms. Cyclopolymerization of 4,4‐bis(vinyloxymethyl)cyclohexene ( 1 ), a divinyl ether with a cyclohexene group, was investigated with the hydrogen chloride/zinc chloride (HCl/ZnCl₂) initiating system in toluene at 0 °C. The reaction proceeded quantitatively to give soluble poly( 1 )s in organic solvents. The content of the unreacted vinyl groups in the produced polymers was less than ～3 mol%, and therefore, the degree of cyclization of the polymers was determined to be ～97%. The number‐average molecular weight (M_n) of the polymers increased in direct proportion to monomer conversion and further increased on addition of a fresh monomer feed to the almost completely polymerized reaction mixture, indicating that living cyclopolymerization of 1 occurred. The chain linking reactions among the formed living cyclopolymers with 1,4‐bis(vinyloxy)cyclohexane ( 3 ) as a crosslinker in toluene at 0 °C produced core‐crosslinked star‐shaped cyclopoly( 1 )s [star‐poly( 1 )s] in high yield (100%). Dihydroxylation of the cyclohexene double bonds of star‐poly( 1 ) gave hydrophilic water‐soluble star‐shaped polymers with rigid arm structure [star‐poly( 1 )‐OH] with thermo‐responsive function in water. T_gs of star‐poly( 1 ) and star‐poly( 1 )‐OH were 135 °C and 216 °C, respectively; these values are very high as vinyl ether‐based star‐shaped polymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1094–1102