HcnS^—与HSC^—n簇离子的量子化学从头计算

应用量子化学从头计算能量解析梯度法，以ＨＦ６／３１Ｇ为基组优化了ＨＣｎＳ＾－与ＨＳＣ＾－ｎ（ｎ＝１～９）同分异构团簇离子的几何结构，计算了它们的电子总能量，结果显示ＨＣｎＳ＾－比相应的ＨＳＣ＾－ｎ稳定，从相邻簇离子的能量差及簇离子的平均原子结构能可知ｎ为偶数的ＨＣｎＳ＾－与ＨＳＣｎ＾－较ｎ为奇数的簇离子稳定，能量的差异随着ｎ的增加而逐渐减小，计算和实验结果完全相符，还分别计算了ＨＣｎＳ＾－失去Ｈ，     

反相离子对色谱法—电化学检测测定亚硝酸根,硫氰酸根,苯胺

本文采用反相离子对色谱法（安培检测）对影响ＮＯ＾－２、ＳＣＮ＾－、Ｃ６Ｈ５ＮＨ２容量因子的各因素进行了研究，建立了分离测定这三种组分的最佳色谱条件。方法快速、灵敏、选择性高。     

低压离子色谱法在酸雨分析中的应用

低压离子色谱是作者提出的一种新的分析法，可以在１．９６～２．９４×１０＾５Ｐａ低压分析碱金属，碱土金属，过渡金属阳离子，无机阴离子及许多有机酸离子，本文用低压离子色谱法分析了成都地区酸雨中Ｎａ，ＮＨ４，Ｋ＾＋，Ｍｇ＾２＋，Ｃａ＾２＋，Ｆ＾－，Ｃｌ＾－，ＮＯ３＾－，ＳＯ＾２－４等离子，获得了满意的结果。     

笼形聚偕氨肟树脂的研究：酸处理树脂的吸附性能

笼形聚偕氨肟树脂（ＣＡＯ）经盐酸处理垢，伯胺基转变成胺盐。酸处理笼形聚偕氨肟树脂（ＡＣＡＯ）对Ｍｇ＾２＋，Ｃａ＾２＋，Ｂａ＾２＋，Ｍｎ＾２＋，Ｃｏ＾２＋，Ｎｉ＾２＋离子不吸附；对Ｚｎ＾２＋，Ｃｄ＾２＋，Ｃｕ＾２＋，Ｐｂ＾２＋离子的吸附效率在２０％以下，但对Ｈｇ＾２＋离子的吸附效率则高达７１．２％；对一些金属络阴离子的吸附效率顺序是Ｆｅ（ＣＮ）＾２－６＞Ｃｒ２Ｏ＾２－７＞ＭｏＯ＾２－４＞ＰｔＣｌ＾２     

四种双冠醚的铯离子选择电极

以合成的四种双（苯并－１８－冠－６）为中性载体制成了ＰＶＣ膜铯离子电极。研究了载体结构，电极膜组成和内充液浓度与电极性能的关系，以邻苯二甲酸二辛酯增塑的４＇，４＂－（邻－亚苯基二氧亚甲基）双（苯并－１８－冠－６）铯离子电极的选择性较好，Ｋ＾ｐ＾ｏ＾ｔＣｓ，ｋ＝２．４×１０＾－＾２，２０℃时，该电极的线性响应范围为５×１０＾－＾５－５×１０＾－＾２ｍｏｌ／Ｌ（ＣｓＣｌ），斜率接近理论值。     

非离子表面活性剂的雾点研究-电解质的影响

研究了１－１型钠盐对五种非 离子表面活性剂水溶液雾点的影响，有九种钠盐使雾点下降，下降的依次是ＩＯ＾－３＞ＯＨ＾－＞Ｆ＾－＞ＣＨ３ＣＯＯ＾－＞ＢｒＯ＾－３＜＞Ｃｌ＾－＞Ｂｒ＾＿＞ＣｌＯ３＾－≥ＮＯ＾－３；有三种钠盐使雾点升高，升高的效率依次是ＣＮＳ＾－＞ＣｌＯ＾－＞Ｉ＾－。     

以Cyanex272为载体的乳状液膜迁移和分离铅的研究

用Ｃｙａｎｅｘ２７２－Ｓｐａｎ８０－甲苯乳状液膜体系研究了铅的迁移行为，确定了铅迁移的适宜条件。在此条件下，许多常见离子如Ｃｕ＾２＋、Ｃｏ＾２＋、Ｎｉ＾２＋、Ｃｄ＾２＋等均不迁移，Ｈｇ＾２＋迁移率很低。因此Ｐｂ＾２＋能与这些离子得到快速且完全的分离。这对分析测定及三废处理等工作具有实际意义。     

一种移动化学反应界面的实验装置

描述了一种移动化学反应界面的实验装置，这一装置备有二台恒流泵用于连续性地驱动阴极液和阳极液，备有二根连接于计录仪的电极用于测定反应管两端的电压。用０．００５ｍｏｌ．Ｌ＾－１ＣｏＣｌ２和０．０１ｍｏｌ．Ｌ＾－１ＮａＯＨ（同时含有０．１ｍｏｌ．Ｌ＾－１背景电解质（ＫＣｌ）形成的移动化学反应界面实验了这一装置。结果表明：（１）能很好地避免电解时产生的氢离子和氢氧根离子的干扰；（２）在单根凝胶柱上可进行多     

卟啉化合物电化学性质研究 Ⅰ.5,10,15,20-四-(4-乙酰氧基苯)卟吩及其Cu、Zn、Fe、Co、Ni配合物的合成及循环伏安研究

本文报道了５，１０，１５，２０－四（４－乙酰氧基苯）卟吩（Ｔ（４ＡＯＰ）Ｐ）及其Ｃｕ，Ｚｎ，Ｆｅ，Ｃｏ，Ｎｉ配合物的合成及其在ＣＨ２Ｃｌ２－０．１ｍｏｌ／ＩＴＢＡＰ体系中的循环伏安（ＣＶ）。研究结果。ＣＶ实验表明：Ｃｕ＾２＾＋，Ｚｎ＾２＾＝，Ｎｉ＾２＾＋离子以稳定的＋２价存在于Ｔ（４ＡＯＰ）Ｐ中，电子转移反应在卟啉环上进行，而Ｆｅ＾３＾＋，Ｃｏ＾２＾＋离子在氧化还原过程中发生价态变化。实验发现...     

ICP—AES间接法连续测定混合物中的氯和碘离子的研究

本文研究了在Ｃｌ和Ｉ＾－的混合物中，加入过量Ａｇ＾＋使Ｃｌ＾－和Ｉ＾－分别以ＡｇＣｌ和ＡｇＩ沉淀后，用ＩＣＰ－ＡＥＳ测定剩余的Ａｇ＾＋，然后用ＮＨ３．Ｈ２Ｏ溶解ＡｇＣｌ沉淀，测定溶解液中的Ａｇ＾＋，间接得到Ｃｌ＾－的含量，以差减法求得Ｉ＾－量，实现Ｃｌ＾－和Ｉ＾＿的间接法连续测定。本文探讨了有关的化学条件和光谱测定条件，对方法的适用性进行了考察－共存离子的干扰情况，方法的精密度，检出限和试样中加入     

Chiral separation based on ligand-exchange capillary electrophoresis using a copper(II)-L-ornithine ternary complex as selector

A ligand-exchange capillary electrophoresis was explored, with L-ornithine as the ligand and copper(II) as the central ion. Its applicability was demonstrated with underivatized and dansyl amino acids, a dipeptide, and drugs with amino alcohol structure. The enantioselectivity was found to be strongly dependent on pH and copper(II)-L-Orn complex concentration. Due to the adsorption of the positively charged species onto the capillary inner walls, the chiral separation selectivity is very high while the efficiency is relatively low. Permanent 1,3-propanediamine-coated capillaries show an improved separation efficiency and theoretical plate numbers increasing from 10(4) to 10(5). Similar phenomena were observed when sodium dodecyl sulfate (SDS) micelles were added to the copper(II) complex solution. The poor separation efficiency of chiral compounds in uncoated capillaries may result from the low rate of the ligand-exchange reactions, and the high enantioselectivity may derive from the complexing process in the adsorbed phase.     

Rapid and sensitive differentiation of anomers,linkage, and position isomers of disaccharides using High-Field Asymmetric Waveform Ion Mobility Spectrometry (FAIMS)

A challenging aspect of structural elucidation of carbohydrates is gaining unambiguous information for anomers, linkage, and position isomers. Such isomers with identical mass can't be easily distinguished in mass spectrometry and a separation step is required prior to mass spectrometry identification. In our laboratory, gas-phase separation and differentiation of anomers, linkage, and position isomers of disaccharides was achieved using High-Field Asymmetric Waveform Ion Mobility Spectrometry (FAIMS). The FAIMS method responds to changes in ion mobility at high field rather than absolute values of ion mobility, and was shown to provide efficient separation and identification of disaccharide isomers at high sensitivity. Separation of analyzed disaccharide isomers can be accomplished at low nM level in a matter of seconds without sample purification or fractionation. Capability for examining a large population of ionic species of disaccharides by this method allowed for correlating structural details of disaccharide isomers with their separation properties in FAIMS. Results for disaccharide isomers indicate that this method could be applied to a larger group of carbohydrates.     

Indirect determination of trace amounts of fluoride in natural waters by ion chromatography: a comparison of on-line post-column fluorimetry and ICP-MS detectors

An alternative method for the determination of trace levels of fluoride in drinking and sea-water samples is presented. It is based on the formation of the aluminium monofluoride complex in excess of Al3+ and separation of the two species formed (AlF2+ and Al3+) in a small (5 cm long, CG2) ion exchange guard column. The final determination is accomplished by both ICP-MS specific detection and post column derivatisation with fluorimetric detection. Fundamental studies on the formation kinetics of the complex, ion chromatographic separation and optimum aluminium concentration were carried out using spectrofluorimetric detection by post-column reaction of the species with 8-hydroxyquinoline-5-sulfonic acid in a micellar medium of cetyltrimethylammonium bromide. Fluorimetric detection showed good detection limits, but interferences from cations such as Mg2+ and Zn2+ required the use of the longer CS2 ion exchange column. Iron interfered in relatively large amounts but adding EDTA to the sample solution eliminated the interference. A similar separation methodology was applied using ICP-MS detection for the indirect determination of fluoride, by monitoring aluminium at mass 27. In this case, a detection limit of 0.1 ng ml-1 was obtained using 0.45 M HNO3 as eluent and no interference caused by high concentrations of iron was observed. The proposed method was applied to the determination of very low levels of fluoride in natural waters.     

Ion chromatographic system with a novel switching suppression device

Ion chromatography (IC) has been a powerful tool for measuring ionic species in environmental samples such as tap, river and drain waters. Suppressor modules (membrane and disposable column types) have been used for reducing the background of a baseline. A new type of suppressor device, which has a suppressor resin and switching valve was developed. Fresh ionic resin is introduced into a groove for each analysis to perform the suppression of the working eluent. The eluent composition for obtaining higher sensitivity and better resolutions among ionic species and carbonate ion was also investigated. Although carbonate buffers are used for ion separation in general, the separation of carbonate ion from other ions was not achieved. A borate eluent resulted in good resolutions and higher sensitivity. A new column was also developed for obtaining higher column efficiency and resolution. The optimization of anion separation using a new IC system (IC-2001) that consists of a new suppressor device, an anion-exchange column (TSKgel SuperIC-Anion, 150x4.6 mm), an autosampler, a conductivity cell and a pump in a compact module is described.     

Rapid chloride analysis using miniaturised isotachophoresis

A new design of miniaturised separation device for performing isotachophoresis (ITP) has been produced. The device contains a simple arrangement of channels comprising a single separation channel with a 'double T' injection geometry. The device was produced in poly(methyl methacrylate) and incorporates an on-column conductivity detector. A new electrolyte system was developed to enable the rapid determination of chloride to be made. This electrolyte system uses a leading ion of 3.5 mM nitrate at pH 3.0 with 0.5 mM indium(III) added as a complexing agent. Use of this electrolyte system with the new separation device allowed chloride samples to be analysed in under 100 s, with a limit of detection (LOD) calculated to be 2.2 mg l(-1).     

The simultaneous determination of chloride, nitrate and sulphate by isotachophoresis using bromide as a leading ion

A new method has been devised to allow the determination of small inorganic anions using isotachophoresis. This method makes use of indium(III) as a counter ion to manipulate the effective mobilities of inorganic anion species by means of complexation reactions. This new procedure successfully allowed the simultaneous determination of nitrate, chloride and sulphate to be realised on a capillary scale instrument and in a chip-based separation device. The electrolyte system developed to allow the separation to be achieved employed a 10mM bromide-based leading electrolyte containing 1.25 mM indium(III) at pH 3.15 and a terminating electrolyte of cyanoacetic acid.     

Gas-phase separation using a trapped ion mobility spectrometer

In the present work we describe the principles of operation, versatility and applicability of a trapped ion mobility spectrometer (TIMS) analyzer for fast, gas-phase separation of molecular ions based on their size-to-charge ratio. Mobility-based separation using a TIMS device is shown for a series for isobar pairs. In a TIMS device, mobility resolution depends on the bath gas velocity and analysis scan speed, with the particularity that the mobility separation can be easily tuned from low to high resolution (R?>?50) in accordance with the analytical challenge . In contrast to traditional drift tube IMS analyzer, a TIMS device can be easily integrated in a mass spectrometer without a noticeable loss in ion transmission or sensitivity, thus providing a powerful separation platform prior to mass analysis.     

低压离子色谱柱及其分离机理

介绍了低压离子色谱柱的种类、分离对象、分离机理及洗脱体系的选取情况     

Ion trapping at atmospheric pressure (760 Torr) and room temperature with a high-field asymmetric waveform ion mobility spectrometer

A method for the confinement of ions at 760 Torr and room temperature is described. We have recently shown that a cylindrical-geometry high-field asymmetric waveform ion mobility spectrometer (FAIMS), which utilizes an ion separation technique based on the change in ion mobility at high electric fields, focuses ions in two dimensions. This article describes a FAIMS device in which the focusing is extended to three dimensions (i.e. ion trap). Characterization of the ion trap was carried out using a laboratory-constructed time-of-flight mass spectrometer. The half-life of a m/z 380 ion in the trap was determined to be 5 ms.     

Speciation analysis of vanadium in natural water samples by electrothermal vaporization inductively coupled plasma optical emission spectrometry after separation/preconcentration with thenoyltrifluoroacetone immobilized on microcrystalline naphthalene

A sensitive and simple method for low temperature electrothermal vaporization inductively coupled plasma optical emission spectrometry (ETV-ICP-OES) determination of V(IV) and V(V) after separation/preconcentration by a micro-column packed with immobilized thenoyltrifluoroacetone (TTA) on microcrystalline naphthalene has been developed. Thenoyltrifluoroacetone was used as both a chelating agent for micro-column separation/preconcentration and a chemical modifier for ETV-ICP-OES determination of vanadium. Both vanadium species could be trapped by micro-column at pH 4.0, and the vanadate (VO₂⁺) ion could be collected selectively at pH 2.4. Solid material loaded with analyte in the micro-column was dissolved with 100 μL of acetone containing 2.0 mmol L⁻¹ TTA and the vanadium was determined subsequently by ETV-ICP-OES. The concentration of vanadyl (VO²⁺) ion was calculated by subtracting the vanadate concentration from the total concentration of vanadium. Under the optimized experimental conditions, the detection limit (3σ) for the preconcentration of 5 mL of aqueous solution is 0.068 μg L⁻¹ for both species and the relative standard deviations were 4.3% for vanadium(V) and 4.8% for vanadium(IV) (c=10 μg L⁻¹, n=7), respectively. The method was applied successfully to the determination of vanadium(IV) and vanadium(V) in natural water samples.