The possible way to evaluate the purity of double-walled carbon nanotubes over single wall carbon nanotubes by chemical doping

Here, we carried out Raman study on chemically doped single wall carbon nanotube (SWNT)/double-walled carbon nanotube (DWNT) mixed bucky-papers. Their highly different Raman responses (e.g., a large upshift of tangential mode of SWNT and no large changes in the frequencies of tangential mode assigned to the outer tubes of the DWNT) upon doping with the sulfuric acid could be used as a qualitative indicator of the purity of the DWNT samples with the concentration of its SWNTs contents.     

Mechanisms of single-walled carbon nanotube probe-sample multistability in tapping mode AFM imaging

When using single-walled carbon nanotube (SWNT) probes to create AFM images of SWNT samples in tapping mode, elastic deformations of the probe and sample result in a decrease in the apparent width of the sample. Here we show that there are two major mechanisms for this effect, smooth gliding and snapping, and compare their dynamics to the case when a conventional silicon tip is used to image a bare silicon surface. Using atomistic and continuum simulations, we analyze in detail the shape of the tip-sample interaction potential for three model cases and show that in the absence of adhesion and friction forces, more than two discrete, physically meaningful solutions of the oscillation amplitude are possible when snapping occurs (in contrast to the existence of one attractive and one repulsive solution for conventional silicon AFM tips). We present experimental results indicating that a continuum of amplitude solutions is possible when using SWNT tips and explain this phenomenon with dynamic simulations that explicitly include tip-sample adhesion and friction forces. We also provide simulation results of SWNT tips imaging Si(111)-CH3 surface step edges and Au nanocrystals, which indicate that SWNT probe multistability may be a general phenomenon, not limited to SWNT samples.     

Effect of Cetyltrimethyl Ammonium Bromide on Electrochemical Determination of Dexamethasone

The effect of surfactants on the electrochemical determination of dexamethasone at an edge plane pyrolytic graphite electrode (EPPGE), modified with single‐walled carbon nanotubes (SWNT) has been investigated. The unique electrocatalytic properties of SWNT along with the synergistic adsorption of CTAB on SWNT lead to sensitive voltammetric response of dexamethasone with the reduction peak at ca. ?1195 mV. The limit of detection and sensitivity of dexamethasone is estimated to be 9.1×10^?10 M and 0.727 µA µM^?1 respectively. The SWNT coated EPPGE had good stability and reproducibility. The analytical utility of the developed method was evaluated by applying it for sensing the drug in human body fluids and for the determination of dexamethasone content in several commercially available pharmaceutical preparations. A comparison of the observed results of proposed method with HPLC clearly indicates that the results of both the methods are in good agreement. The product obtained after the reduction of dexamethasone has also been characterized using ¹H NMR and carbonyl group at position 3 has been found to reduce. The method is instant, simple and accurate and can be easily applied for detecting cases of doping.     

In situ optical spectroelectrochemistry of single-walled carbon nanotube thin films

A detailed study is presented on the optical absorption of thin films of single-walled carbon nanotubes (SWNT) under electrochemical conditions. The procedure for the preparation of free-standing semitransparent films of SWNT is used for the fabrication of a working electrode for transmission optical spectroelectrochemistry. The analysis of the potential dependent spectroscopic response of the SWNT film benefits from the widest possible electrochemical window, in which the charging of SWNT can safely be investigated. This electrochemical window is not limited by parasitic electrochemistry and/or galvanic breakdown reactions occurring at supporting electrode materials such as indium–tin oxide conducting glass or semitransparent Pt film, which were employed in earlier studies. Electrochemical doping of SWNT is observable at the optical absorptions, which are assigned to allowed electronic transitions between van Hove singularities in the density of states of SWNT. Furthermore, the spectral response of counterions, balancing the charging of the nanotube skeleton, is traceable at certain conditions. The latter effect is monitored here through the overtones of C–H stretching vibrations from tetrabutylammonium cations.     

Thermal annealing of SiC nanoparticles induces SWNT nucleation: evidence for a catalyst-independent VSS mechanism

Density-functional tight-binding molecular dynamics (DFTB/MD) methods were employed to demonstrate single-walled carbon nanotube (SWNT) nucleation resulting from thermal annealing of SiC nanoparticles. SWNT nucleation in this case is preceded by a change of the SiC structure from a crystalline one, to one in which silicon and carbon are segregated. This structural transformation ultimately resulted in the formation of extended polyyne chains on the SiC nanoparticle surface. These polyyne chains subsequently coalesced, forming an extended sp(2)-hybridized carbon cap on the SiC nanoparticle. The kinetics of this process were enhanced significantly at higher temperatures (2500 K), compared to lower temperatures (1200 K) and so directly correlated to the surface premelting behavior of the nanoparticle structure. Analysis of the SiC nanoparticle Lindemann index between 1000 and 3000 K indicated that SWNT nucleation at temperatures below 2600 K occurred in the solid, or quasi-solid, phase. Thus, the traditional vapor-liquid-solid mechanism of SWNT growth does not apply in the case of SiC nanoparticles. Instead, we propose that this example of SWNT nucleation constitutes evidence of a vapor-solid-solid process. This conclusion complements our recent observations regarding SWNT nucleation on SiO(2) nanoparticles (A. J. Page, K. R. S. Chandrakumar, S. Irle and K. Morokuma, J. Am. Chem. Soc., 2011, 133, 621-628). In addition, similarities between the atomistic SWNT nucleation mechanisms on SiC and SiO(2) catalysts provide the first evidence of a catalyst-independent SWNT nucleation mechanism with respect to 'non-traditional' SWNT catalyst species.     

RBM band shift-evidenced dispersion mechanism of single-wall carbon nanotube bundles with NaDDBS

The dispersion process of single-wall carbon nanotube (SWNT) by using sodium dodecylbenzene sulfonate (NaDDBS) was studied by means of surface tension measurements, ultraviolet-visible (UV-Vis) spectroscopy, scanning electron microscopy (SEM), and transmission electron spectroscopy (TEM). The critical micelle concentration (CMC) and the concentration where the surface tension begins to drop increase by the presence of SWNT. The isotherm of NaDDBS amount adsorbed on SWNT shows the plateau region at 0.2-6 mM and the saturated region above 40 mM. The external surface of SWNT bundle is fully covered with adsorbed NaDDBS at the plateau region, showing that SWNTs can be dispersed with the bundle form. On the other hand, SWNTs are dispersed in individual tubes at the saturated region, where the adsorption amount corresponds to coating of individual tube surfaces with NaDDBS. This dispersion state was confirmed by SEM and TEM observations. The effect of the dispersion state of SWNTs on radial breathing mode in Raman spectrum gave inherent peak shifts, being the in situ evidences on the step-wise dispersion mechanism of the SWNT bundle to the individual tubes.     

吲哚美辛在单壁碳纳米管修饰电极上的电化学行为

运用伏安法研究了吲哚美辛在单壁碳纳米管修饰电极上的电化学行为.在0.1 mol/L HAc-NaAc缓冲溶液(pH 4.5)中,吲哚美辛于0.91 V (vs.SCE)电位处有一个峰形很好的氧化峰.与裸玻碳电极相比,吲哚美辛在修饰电极上的电位正移了约30 mV,峰电流增加了近10倍,表明该修饰电极对吲哚美辛有较强的电催化作用.搅拌条件下开路富集2 min,氧化峰电流与吲哚美辛在5.5×10-7～1.1×10-5 mol/L浓度范围内呈良好的线性关系,检出限为1.1×10-7 mol/L.该方法可用于药剂中吲哚美辛的分析.     

Raman studies of solutions of single-wall carbon nanotube salts

Polyelectrolyte solutions of Na-doped single-wall carbon nanotube (SWNT) salts are studied by Raman spectroscopy. Their Raman signature is first compared to undoped SWNT suspensions and dry alkali-doped SWNT powders, and the results indicate that the nanotube solutions consist of heavily doped (charged) SWNT. Raman signature of doping is then used to monitor in situ the oxidation reaction of the nanotube salt solutions upon exposure to air and to an acceptor molecule (benzoquinone). The results indicate a direct charge-transfer reaction from the acceptor molecule to the SWNT, leading to their gradual charge neutralization and eventual precipitation in solution. The results are consistent with a simple redox titration process occurring at the thermodynamical equilibrium.     

Antenna chemistry with metallic single-walled carbon nanotubes

We show that, when subjected to microwave fields, surfactant-stabilized single-walled carbon nanotubes (SWNTs) develop polarization potentials at their extremities that readily drive electrochemical reactions. In the presence of transition metal salts with high oxidation potential (e.g., FeCl3), SWNTs drive reductive condensation to metallic nanoparticles with essentially diffusion-limited kinetics in a laboratory microwave reactor. Using HAuCl4, metallic particles and sheaths deposit regioselectively at the SWNT tips, yielding novel SWNT-metal composite nanostructures. This process is shown to activate exclusively metallic SWNTs; a degree of diameter selectivity is observed using acceptors with different oxidation potentials. The reaction mechanism is shown to involve Fowler-Nordheim field emission in solution, where electric fields concentrate at the SWNT tips (attaining approximately 10(9) V/m) due to the SWNT high aspect ratio (approximately 1000) and gradient compression in the insulating surfactant monolayer. Nanotube antenna chemistry is remarkably simple and should be useful in SWNT separation and fractionation processes, while the unusual nanostructures produced could impact nanomedicine, energy harvesting, and synthetic applications.     

Fabrication and Properties of Conducting Polypyrrole/SWNT‐PABS Composite Films and Nanotubes

We report the electropolymerization and characterization of polypyrrole films doped with poly(m‐aminobenzene sulfonic acid (PABS) functionalized single‐walled nanotubes (SWNT) (PPy/SWNT‐PABS). The negatively charged water‐soluble SWNT‐PABS served as anionic dopant during the electropolymerization to synthesize PPy/SWNT‐PABS composite films. The synthetic, morphological and electrical properties of PPy/SWNT‐PABS films and chloride doped polypyrrole (PPy/Cl) films were compared. Characterization was performed by cyclic voltammetry, atomic force microscopy (AFM), scanning electron microscopy (SEM) and Raman spectroscopy. SEM and AFM images revealed that the incorporation of SWNT‐PABS significantly altered the morphology of the PPy. Cyclic voltammetry showed improved electrochemical properties of PPy/SWNT‐PABS films as compared to PPy/Cl films. Raman Spectroscopy confirmed the presence of SWNT‐PABS within composite films. Field effect transistor (FET) and electrical characterization studies show that the incorporation of the SWNT‐PABS increased the electronic performance of PPy/SWNT‐PABS films when compared to PPy/Cl films. Finally, we fabricated PPy/SWNT‐PABS nanotubes which may lead to potential applications to sensors and other electronic devices.     

Transparent conductors from carbon nanotubes LBL-assembled with polymer dopant with π-π electron transfer

Single-walled carbon nanotube (SWNT) and other carbon-based coatings are being considered as replacements for indium tin oxide (ITO). The problems of transparent conductors (TCs) coatings from SWNT and similar materials include poor mechanical properties, high roughness, low temperature resilience, and fast loss of conductivity. The simultaneous realization of these desirable characteristics can be achieved using high structural control of layer-by-layer (LBL) deposition, which is demonstrated by the assembly of hydroethyl cellulose (HOCS) and sulfonated polyetheretherketone (SPEEK)-SWNTs. A new type of SWNT doping based on electron transfer from valence bands of nanotubes to unoccupied levels of SPEEK through π-π interactions was identified for this system. It leads to a conductivity of 1.1 × 10(5) S/m at 66 wt % loadings of SWNT. This is better than other polymer/SWNT composites and translates into surface conductivity of 920 Ω/? and transmittance of 86.7% at 550 nm. The prepared LBL films also revealed unusually high temperature resilience up to 500 °C, and low roughness of 3.5 nm (ITO glass -2.4 nm). Tensile modulus, ultimate strength, and toughness of such coatings are 13 ± 2 GPa, 366 ± 35 MPa, and 8 ± 3 kJ/m(3), respectively, and exceed corresponding parameters of all similar TCs. The cumulative figure of merit, ∏(TC), which included the critical failure strain relevant for flexible electronics, was ∏(TC) = 0.022 and should be compared to ∏(TC) = 0.006 for commercial ITO. Further optimization is possible using stratified nanoscale coatings and improved doping from the macromolecular LBL components.     

铁氰化镧修饰电极的制备及表征

An electroactive polynuclear inorganic compound of rare earth metal hexacyanoferrate, lanthanum hexacyanoferrate (LaHCF), was prepared by electrochemical deposition on the surface of a glassy carbon electrode with a potential cycling procedure. The cyclic voltammogram of LaHCF exhibits a pair of well-defined redox peaks with the formal potential of 208 mV (vs. SCE) at a scan rate of 100 mV/s in 0.2 mol/L NaCl solution and the redox peak currents increase linearly with the square root of the scan rate up to 1000 mV/s. The effects of the concentration of supporting electrolyte on the electrochemical characteristics of LaHCF were studied by voltammetry. LaHCF was also characterizated by scanning electron microscope (SEM), FTIR and XPS techniques.     

Effect of presence of 18-crown-6 on the response of 1-pyrrolidine dicarbodithioate-based lead selective electrode

The lipophilic ammonium salt of 1-pyrrolidine dicarbodithioic acid (PCDT)[I] was introduced as a selective ionophore for a sensitive Pb-ion selective electrode. Also, the effect of immobilization of 18-crown-6 (CW), into the above membrane, on the electrode performance was discussed. The slope of the PCDT-based [I] electrode was (26–30 mV decade⁻¹), while it was (29-30 mV decade⁻¹) for (PCDT+CW)-based [II] electrode according to the doping time. The linear concentration ranges were (1×10⁻⁶–1×10⁻¹ M) and (5×10⁻⁵–1×10⁻¹ M) for electrode types [I] and [II] after one-day doping. The working pH ranges were (5.0–10.0) and (7.0–10.0) for electrode types [I] and [II], respectively. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Na⁺, Ag⁺ and Fe³⁺ were the real interference. Application of using the electrode for the determination of lead in lubrication oil samples was performed with RSD (0.86–1.03%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Selective synthesis combined with chemical separation of single-walled carbon nanotubes for chirality selection

Single-walled carbon nanotubes (SWNTs) are potential materials for future nanoelectronics. Since the electronic and optical properties of SWNTs strongly depend on tube diameter and chirality, obtaining SWNTs with narrow (n,m) chirality distribution by selective growth or chemical separation has been an active area of research. Here, we demonstrate that a new, bimetallic FeRu catalyst affords SWNT growth with narrow diameter and chirality distribution in methane CVD. At 600 degrees C, methane CVD on FeRu catalyst produced predominantly (6,5) SWNTs according to UV-vis-NIR absorption and photoluminescence excitation/emission (PLE) spectroscopic characterization. At 850 degrees C, the dominant semiconducting species produced are (8,4), (7,6), and (7,5) SWNTs, with much narrower distributions in diameter and chirality than materials grown by other catalysts. Further, we show that narrow diameter/chirality growth combined with chemical separation by ion exchange chromatography (IEC) greatly facilitates achieving single (m,n) SWNT samples, as demonstrated by obtaining highly enriched (8,4) SWNTs with near elimination of metallic SWNTs existing in the as-grown material.     

(n,m) Abundance evaluation of single-walled carbon nanotubes by fluorescence and absorption spectroscopy

A methodology that takes into account the (n,m) structure of single-walled carbon nanotubes (SWNTs), through an exciton-exciton resonance model and an electron-phonon interaction model, was employed in order to evaluate the semiconducting (n,m) abundance of two SWNT samples (i.e., Co-MCM-41 and HiPco). This was based on photoluminescence and near-infrared absorption data obtained on aqueous suspensions of individually dispersed SWNTs. In the absence of known (n,m) abundance SWNT samples, we resorted to determining the diameter distribution curves for both samples, which were found to obey an unsymmetrical log-normal distribution, typical for vapor-phase particle growth. Using this log-normal function, we reconstructed the near-infrared E S11 absorption spectrum of the narrow diameter distribution Co-MCM-41 SWNT sample, which in turn enabled us to assess the predictions of these two theoretical models. High spectral reconstruction accuracy was obtained from the electron-phonon interaction model when considering (11,0) and (10,0) zigzag nanotubes, along with (n,m) line widths inversely proportional to their extinction coefficients.     

Determination of quercetin and its glucosides in onion by electrochemical methods

Quercetin (Q), quercetin-3,4'-diO-beta-glucoside (Q3,4'G), quercetin-3-O-beta-glucoside (Q3G) and quercetin-4'-O-beta-glucoside (Q4'G) were determined in onion bulbs (Allium cepa) by HPLC with amperometric detection after analysis of the hydrodynamic voltammograms of flavonoid standards within the potential range of 50-1000 mV and by cyclic voltammetry (CV) method. The hydrodynamic voltammetric profiles of flavonoids showed that the peak current of Q, Q3G, Q4'G and Q3,4'G increased rapidly when the applied potential exceeded +450 mV (vs. SCE). High sensitivity and low background current were observed at the applied potential of +950 mV (vs. SCE). The lower limits of detection (LOD) were determined at signal-to-noise ratio of 3 and showed the following values: 8.05x10(-8)M (Q), 1.08x10(-7) M (Q3G), 1.22x10(-7) M (Q4'G) and 2.6x10(-7) M (Q3,4'G). The data provided by HPLC-UV-MS confirmed the presence of Q, Q3G, Q4'G and Q3,4'G in 80% methanol extracts of lyophilised onion bulbs. The CV method was applied for the qualitative assessment of onion flavonoids followed by the determination of anodic peak potential (E(a)) of the standards. The qualitative analysis of onion flavonoids was based on the anodic peak current (I(a)) of the extracts after external standards addition. The recorded cyclic voltammograms of the above flavonoid standards showed that all four compounds had well-defined oxidation waves with peak potentials of 310, 390, 482 and 800 mV (vs. Ag/AgCl) for Q, Q3G, Q4'G and Q3,4'G in 50 mM acetate-acetic buffer (pH 5.5) in 80% methanol, respectively. The study proved applicability of the CV method for identifying Q, Q3G, Q4'G and Q3,4'G in onion.     

Atomic force microscopy measurements of peptide-wrapped single-walled carbon nanotube diameters.

With a vertical resolution of 0.1 nm, atomic force microscopy (AFM) height measurements can be used to determine accurately the diameter of single-walled carbon nanotubes (SWNT) with the assumption that they have circular cross sections. The aim of this article is to draw attention to the need to optimize operating parameters in tapping mode for quantitative AFM height (diameter) analysis of SWNTs. Using silicon tip/cantilever assemblies with force constants ranging from 0.9 to 40 N m(-1), we examined the effect of applied force on the apparent diameter of SWNT wrapped with a 29-residue amphiphilic alpha-helical peptide. A decrease in apparent height (SWNT diameter) with increasing applied force was observed for the higher force constant cantilevers. Cantilevers having force constants of 0.9 and 3 N m(-1) demonstrated minimal vertical sample compression with increasing applied force. The effects of AFM image pixel density and scan speed on the measured height (diameter) of SWNTs were also assessed.     

Effect of chemical treatment on electrical conductivity, infrared absorption, and Raman spectra of single-walled carbon nanotubes

We investigate the magnitude and temperature dependence of electrical conductivity, the optical and infrared absorption, and the Raman spectra of single-walled carbon nanotube (SWNT) bucky-paper after chemical treatment and determine the correlations between the changes in these properties. Ionic-acceptor doping of the SWNT bucky-paper (with SOCl(2), iodine, H(2)SO(3), etc.) causes an increase of electrical conductivity that correlates with an increase of the absorbance in the far-IR region and an increase in the frequency of Raman spectral lines. Conversely, treatment with other molecules (e.g., aniline, PyPhF(5), PhCH(2)Br, etc.) leads to a decrease in both conductivity and far-IR absorption. The temperature dependence of the conductivity gives a good indication of the presence of metallic charge carriers and is in agreement with the model of interrupted metallic conduction.     

Unlocking the Transition of Electrochemical Water Oxidation Mechanism Induced by Heteroatom Doping

Heteroatom doping has emerged as a highly effective strategy to enhance the activity of metal-based electrocatalysts toward the oxygen evolution reaction (OER). It is widely accepted that the doping does not switch the OER mechanism from the adsorbate evolution mechanism (AEM) to the lattice-oxygen-mediated mechanism (LOM), and the enhanced activity is attributed to the optimized binding energies toward oxygen intermediates. However, this seems inconsistent with the fact that the overpotential of doped OER electrocatalysts (<300 mV) is considerably smaller than the limit of AEM (>370 mV). To determine the origin of this inconsistency, we select phosphorus (P)-doped nickel-iron mixed oxides as the model electrocatalysts and observe that the doping enhances the covalency of the metal-oxygen bonds to drive the OER pathway transition from the AEM to the LOM, thereby breaking the adsorption linear relation between *OH and *OOH in the AEM. Consequently, the obtained P-doped oxides display a small overpotential of 237 mV at 10 mA cm⁻². Beyond P, the similar pathway transition is also observed on the sulfur doping. These findings offer new insights into the substantially enhanced OER activity originating from heteroatom doping.     

Effect of doping order on metal-free heteroatoms dual-doped carbon as oxygen reduction electrocatalyst

Metal-free heteroatoms dual-doped carbon has been recognized as one of the most promising Pt/C-substitutes for oxygen reduction reaction(ORR).Herein,we optimize the preparation process by doping order of metal-free heteroatoms to obtain the best electrocatalytic performance through three types of dual-doped carbon,including XC-N(first X doping then N doping),NC-X(first N doping then X doping) and NXC(N and X doping)(X=P,S and F).XC-N has more defect than the other two indicated by Raman spectra.X-ray photoelectron spectrom(XPS) measurements indicate that N and X have been dual-doped into the carbon matrix with different doping contents and modes,Electrocatalytic results,including the potential of ORR peak(E_p),the half-wave potential,the diffusion-limiting current density mainly follows the order of XC-NNC-X NXC,Furthermore,the synergistic effect of second atom doping are also compared with the single doped carbon(NC,PC,SC and FC).The differences in electronegativity and atomic radius of these metal-free heteroatoms can affect the defect degree,the doping content and mode of hete roatoms on carbon matrix,induce polarization effect and space effect to affect O_2 adsorption and product desorption,ultimately to the ORR electrocatalytic performance.