脉冲电沉积钯镍合金纳米颗粒及其甲酸电催化氧化

采用方波脉冲方法,在钯镍合金电解液中成功地电化学沉积出镍原子含量分别为12.0%、16.4%和22.6%的钯镍合金纳米颗粒.钯镍合金纳米颗粒为球状,粒径50~80 nm.随钯镍合金生长电位负移,合金的镍含量提高,其纳米颗粒大小基本相似但纳米颗粒数目增多,交联度提高和真实活性面积增大.钯镍合金纳米颗粒镍含量提高,在硫酸溶液中其氢弱吸附峰电流增大.钯镍合金纳米颗粒电极的甲酸电催化氧化活性较好,随合金纳米颗粒的镍含量提高和交联度增加,合金纳米颗粒电极的甲酸电催化氧化稳定性更高.     

Ni-B非晶态合金电极上乙醇的电氧化及其动力学参数的测定

应用循环伏安法研究了碱性介质中Ni-B非晶态合金纳米粉末微电极和化学镀Ni-B非晶态合金微盘电极上乙醇的电催化氧化. 结果表明, Ni-B非晶态合金纳米粉末微电极和化学镀Ni-B非晶态合金微盘电极对碱性溶液中乙醇的氧化均具有很高的电催化作用, 且前者的电催化氧化活性高于后者. 运用稳态极化曲线测定了Ni-B非晶态合金纳米粉末微电极上乙醇的电催化氧化动力学参数. 与高择优取向(220)镍电极比较, 碱性介质中Ni-B非晶态合金纳米粉末微电极上乙醇的电催化氧化速率显著提高. 采用循环伏安法测定的Ni-B非晶态合金纳米粉末微电极上Ni(OH)2的质子扩散系数高出文献报道的镍纳米线电极和表面化学镀Co的球形Ni(OH)2粉末电极约2个数量级.     

辐射状钯纳米花的可控合成及其电催化性能的研究

水体系中,以十六烷基三甲基溴化铵(CTAB)和L-精氨酸为表面活性剂,抗坏血酸还原PdCl42-,制得了直径范围在50~80 nm之间的辐射状钯纳米花.实验表明,CTAB和L-精氨酸对辐射状钯纳米花的形成起着协同作用.此外,还研究了辐射状钯纳米花对甲酸氧化的电催化活性.在0.5 mol/L H2SO4+0.5 mol/L HCOOH溶液中的循环伏安结果表明,辐射状钯纳米花修饰电极在酸性溶液中电催化氧化甲酸的峰电流密度约为101 mA/mg,明显优于实心钯纳米粒子修饰的电极(峰电流密度为50 mA/mg),且表现出较高的稳定性.     

Ni-B非晶态合金纳米粉末微电极上甲醇的电催化氧化

应用循环伏安法研究了碱性介质中Ni-B非晶态合金纳米粉末微电极上甲醇的电催化氧化.结果表明,Ni-B非晶态合金纳米粉末微电极表现出很高的甲醇氧化电催化活性,较之高择优取向(220)的镍电极,其氧化起始电位负移了0.04V;氧化电流密度约大2个数量级,根据稳态极化曲线测定,与高择优取向(220)镍电极相比较,在Ni-B非晶态合金纳米粉末微电极上,Ni(Ⅲ)与甲醇反应和Ni(Ⅱ)氧化为Ni(Ⅲ)及其逆反应的速率常数依次约大2个、3个和3个数量级.     

电催化甲酸氧化中钯微粒与聚苯胺的相互作用

采用电化学、ＸＰＳ和拉曼光谱研究钯微粒修饰聚苯胺（ＰＡＮ（Ｐｄ）电极对甲酸氧化的电催化行为。由于钯与ＰＡＮ的相互作用，钯微粒在所研究的电位区间可稳定地固定于ＰＡＮ中，且甲酸在钯上的氧化明显地抑制ＰＡＮ的氧化降解，使ＰＡＮ（Ｐｄ）电极电催化甲酸氧化反应具有高的稳定性和活性。     

高分散镍-硼/纳米多孔铜非晶态合金电极上葡萄糖的电催化氧化

通过酸腐蚀去合金法处理热扩散制备的铜基表面铜锌合金得到纳米多孔铜(NPC)材料. 以NPC为载体,采用超声辅助化学镀制备Ni-B/NPC合金电极. X射线衍射(XRD)和扫描电镜(SEM)表明Ni-B/NPC电极呈现由高分散纳米颗粒组成的非晶态结构. 计时电流法(CA)结果表明化学镀5 min制备的Ni-B/NPC电极具有最大的电化学活性表面积(EASA). 循环伏安法(CV)结果表明,与块状镍电极相比,碱性介质中在Ni-B/NPC电极上葡萄糖起始氧化电位负移39 mV,氧化峰电流提高了18.9倍. 采用线性扫描伏安法(LSV)、CA和电化学阻抗谱(EIS)测定Ni-B/NPC电极对葡萄糖电催化氧化的电子转移系数(β)、电催化氧化反应速率常数(k)和葡萄糖的扩散系数(D)等动力学参数. 结果表明高分散Ni-B/NPC非晶态合金电极对碱性介质中葡萄糖的氧化具有较高的电催化活性和稳定性.     

炭载Pd-Pb合金纳米粒子对甲酸电催化氧化的影响

通过浸渍还原方法制备了具有不同化学计量比的炭载Pd-Pb合金纳米粒子催化剂. XRD和TEM测试结果表明, Pd-Pb合金纳米粒子的晶格常数随Pb元素含量的增加而增加, 相应的粒子尺寸随Pb元素含量的增加而减小. 循环伏安、CO溶出和计时电流等电化学测试结果表明, 炭载Pd-Pb合金纳米粒子催化剂对甲酸氧化的电催化活性随Pb含量的增加而降低.     

Pd/石墨烯复合材料的制备及电催化甲酸和甲醇性能研究

通过电解高纯石墨棒的方法制备氧化石墨,将氧化石墨在超纯水中超声,形成稳定的氧化石墨烯分散液。以氧化石墨烯分散液和氯化钯作为前驱体,采用一步电沉积法制备Pd/石墨烯纳米复合材料。用扫描电子显微镜(SEM)、X射线衍射仪(XRD)及紫外可见分光光度计(UV-vis)对物质的表面形貌及物相组成进行表征分析。用循环伏安法(CV)和计时电流法(CA)研究了Pd/石墨烯催化剂对甲酸和甲醇的电催化氧化活性。结果表明:与纳米钯修饰电极相比,Pd/石墨烯修饰电极对甲酸及甲醇的电催化氧化活性有了极大的提高。     

纳米钯催化剂对甲醇的电催化氧化

采用水热法,以甲醛作还原剂还原Pd2+-EDTA络合物,制得钛基纳米钯颗粒电极(nanoPd/Ti).扫描电子显微镜(SEM)显示,纳米钯颗粒直径约为60 nm,形成三维立体网状结构.在碱性溶液中,循环伏安及交流阻抗测试分别表明:nanoPd/Ti电极对甲醇氧化有极高的阳极电流、较低的起始氧化电位和较强的抗CO毒化能力.在nanoPd/Ti电极上甲醇电氧化反应的阻抗值较低,增加甲醇浓度,电极阻抗更低.电极对甲醇氧化具有极好的电催化活性.     

一种新型的甲酸/铁离子燃料电池

以甲酸为燃料、 Fe³⁺为氧化剂组成了一种新型的甲酸/铁离子燃料电池, 阳极催化剂为多壁碳纳米管(MWCNT)或β-环糊精修饰的MWCNT(β-CD-MWCNT)负载的金属钯或钯锡纳米颗粒: PdSn/MWCNT, Pd/β-CD-MWCNT和PdSn/β-CD-MWCNT. 运用循环伏安(CV)和计时电流(CA)等技术研究了各催化剂在碱性条件下对甲酸氧化反应的电催化活性. 结果表明, 加入适量的金属锡能促进钯对甲酸的电催化氧化, 甲酸氧化电位提前, 电流密度增加; 环糊精的改性对催化剂电催化活性有一定提升. 将上述催化剂制成电池阳极片, 碳粉制成电极阴极片, 组成甲酸/铁离子燃料电池并测试其放电性能. 结果表明, 电池的开路电压在0.981.20 V之间; 以PdSn/β-CD-MWCNT为阳极时, 其最大放电电流密度达50 mA/cm², 最大功率密度达12.6 mW/cm², 远优于以Pd/C为阳极的电池性能.     

Preparation and electrochemistry of Pd-Ni/Si nanowire nanocomposite catalytic anode for direct ethanol fuel cell

A new silicon-based anode suitable for direct ethanol fuel cells (DEFCs) is described. Pd-Ni nanoparticles are coated on Si nanowires (SiNWs) by electroless co-plating to form the catalytic materials. The electrocatalytic properties of the SiNWs and ethanol oxidation on the Pd-Ni catalyst (Pd-Ni/SiNWs) are investigated electrochemically. The effects of temperature and working potential limit in the anodic direction on ethanol oxidation are studied by cyclic voltammetry. The Pd-Ni/SiNWs electrode exhibits higher electrocatalytic activity and better long-term stability in an alkaline solution. It also yields a larger current density and negative onset potential thus boding well for its application to fuel cells.     

钯镍合金薄膜电极上甲酸电氧化-去合金化效应

在含PdC l2、N iSO4和乙二胺的弱碱性镀液中,于Au电极上用恒电位电沉积Pd-N i合金薄膜,后经酸性溶液中循环伏安法处理,得到去合金化的Pd-N i电极.扫描电镜以及电化学测试表明,去合金化处理使Pd-N i镀膜表面微观粗糙度增加,比表面积增大;ICP-AES和XPS分析证实合金表层N i的优先溶出造成Pd的富集.去合金化处理的Pd-N i电极电催化氧化甲酸的活性明显优于未处理的Pd-N i电极和多晶Pd电极.     

碱性介质中多孔纳米结构镍/钯-镍电极上甲醇电氧化反应(英文)

A nanostructured Ni/Pd-Ni catalyst with high activity for methanol oxidation in alkaline solution was prepared by electrodeposition followed by galvanic replacement, that is, electrodeposition of Ni-Zn on a Ni coating with subsequent replacement of the Zn by Pd at the open circuit potential in a Pd-containing alkaline solution. The surface morphology and composition of the coatings were examined by energy dispersive X-ray spectroscopy and scanning electron microscopy. The Ni/Pd-Ni coatings were porous and were composed of discrete Pd nanoparticles of about 58 nm. The electrocatalytic activity of the Ni/Pd-Ni electrodes for the oxidation of methanol was examined by cyclic voltammetry and electrochemical impedance spectroscopy. The onset potentials for methanol oxidation on Ni/Pd-Ni were 0.077 V and 0.884 V, which were lower than those for flat Pd and smooth Ni electrodes, respectively. The anodic peak current densities of these electrodes were 4.33 and 8.34 times higher than those of flat Pd (58.4 mA/cm2 vs 13.47 mA/cm2) and smooth Ni (58.4 mA/cm2 vs 7 mA/cm2). The nanostructured Ni/Pd-Ni electrode is a promising catalyst for methanol oxidation in alkaline media for fuel cell application.     

多壁碳纳米管负载Pd-Ni电催化剂对乙二醇的电催化氧化

采用微波加热还原法制备了不同化学计量比的Pd-Ni复合多壁碳纳米管(Pd-Ni/MWCNT)催化剂. 通过X射线衍射(XRD)、透射电镜(TEM)和能量散射谱(EDS)等微结构和组成表征表明, 所合成的催化剂中Pd-Ni合金具有较小的纳米颗粒以及较好的分散程度. 循环伏安(CV)、线性扫描(LSV)、计时电流方法(CA)和交流阻抗(EIS)等测试表明, Pd-Ni(3:1)/MWCNT催化剂对乙二醇的电化学氧化具有较高的催化活性.     

丙醇和丁醇异构体在钯镍电极上的电催化氧化

β环糊精(β-CD)具有特殊的空腔结构,将β-CD修饰的多壁碳纳米管(MWCNT)涂在钛基底上,采用电沉积的方法在修饰的钛基底上沉积纳米PdNi催化剂。SEM结果表明,PdNi纳米颗粒在β-CD/MWCNT修饰的钛片上有较好的分散度,粒径为90~130 nm。在碱性溶液中,测试了PdNi-β-CD/MWCNT/Ti电极分别对丙醇和丁醇不同异构体氧化的电催化活性;通过计算与-OH相连的碳原子上的Muliken净电荷,分析不同异构体的氧化机理。结果表明,不同异构体的氧化活性不同,PdNi-β-CD/MWCNT/Ti电极对正丙醇和正丁醇的氧化活性明显高于其异构体,-OH所在碳原子上的Muliken 净电荷越小,醇类分子越容易被氧化。     

Voltammetric determination of paracetamol at NiO nanoparticles-modified carbon paste electrode in bulk and tablet dosage forms

Nickel oxide (NiO) nanoparticles were synthesized by a rapid method and well characterized. The nanoparticles were then used with graphite powder to prepare modified carbon paste electrode (CPE/NiO) for electrocatalytic oxidation of paracetamol (AC). The CPE/NiO showed higher electrocatalytic activity than nickel rod electrode in electrocatalytic oxidation of AC in alkaline media. The assay of AC, mechanism and kinetics of the electrooxidation process were investigated by cyclic voltammetry and chronoamperometry. The catalytic rate constant and the charge transfer coefficient of AC electrooxidation by the active nickel species and the diffusion coefficient of AC were also reported. The linear dependence of the peak current on the concentration of the AC was observed in the range 2–14 mM. This procedure was successfully applied to the determination of AC in tablets. The results showed sufficient precision, accuracy and achieved a mean recovery of 97.2% (RSD = 6.7%).     

Application of nickel phosphate nanoparticles and VSB-5 in the modification of carbon paste electrode for electrocatalytic oxidation of methanol

Carbon paste electrodes were modified by nickel phosphate nanoparticles and nickel phosphate Versailles Santa Barbara-5 molecular sieves. Then, transition metal ions of Ni(II) were incorporated to the nickel phosphate by immersion of the modified electrode in a 0.1-M nickel chloride solution. The electrochemical behaviors of the modified electrodes were studied using cyclic voltammetry. These modified electrodes were used as anode for the electrocatalytic oxidation of methanol in alkaline medium. The influence of some parameters such as different molecular sieves, scan rate of potential, and methanol concentration was investigated on the anodic peak height of the methanol oxidation. The best result was obtained by nickel phosphate nanoparticles.     

炭载Pd-Ni合金纳米粒子对甲酸的电催化氧化

通过液相还原法制备了具有不同原子比例的Pd-Ni/C催化剂,并且使用X射线衍射（XRD）、透射电子显微镜(TEM)和X射线光电子能谱(XPS) 等表征手段对制备的催化剂进行了表征,总结了Ni的掺杂对Pd-Ni合金纳米粒子的尺寸及晶体结构的影响。电化学测试结果表明：适量的Ni的掺杂不但能够增强催化剂对甲酸催化氧化的活性,而且还能够提高催化剂的稳定性。因此,Pd-Ni/C催化剂是一类具有潜在应用前景的直接甲酸燃料电池阳极催化剂     

Pt-Ni与Pd-Ni纳米薄膜的电化学制备和乙醇电催化性能研究(英文)

通过电沉积法在Ti基体上制备具有纳米结构的Pt-Ni和Pd-Ni薄膜,前者呈纳米花瓣形状,厚度为10～20 nm,后者主要由纳米颗粒组成,大小为50～60 nm.XRD测试结果显示,Pt-Ni和Pd-Ni纳米薄膜结晶程度较差.循环伏安法测试薄膜对乙醇电催化氧化的性能,结果表明Pt-Ni和Pd-Ni纳米薄膜可使乙醇起始氧化电位分别负移至-0.74 V和-0.71 V,且在碱性介质中加Ni可提高催化剂的活性和抗毒化性能.