Al2O3/Au(111)反相催化剂在CO氧化反应中界面作用的理论研究

氧化物负载的金催化剂具有温和条件下优异的CO催化氧化活性。实验与理论计算表明,金与氧化物两相界面在催化反应过程中具有重要地位。反相催化剂提供了全新的角度以探究界面的重要地位。本文以Au（111）表面负载Al₂O₃团簇为反相催化剂模型,基于密度泛函理论,对催化剂模型的构型、界面性质以及O₂、CO的吸附与氧化进行了理论计算与研究。理论计算表明：电荷的迁移增强了Al₂O₃小团簇在Au（111）表面的附着,在催化剂金表面与氧化铝的两相界面位置,Au原子与Al原子的协同作用使得氧分子易于在界面位置吸附,并因此高度活化。对催化CO氧化反应路径,分别计算了缔合机理和解离机理不同路径,从活化能分析表明缔合机理比解离机理更可能发生。本文的工作揭示了反相催化剂催化CO氧化的活性本质,表明两相界面在金催化CO氧化中具有重要作用。     

Photocatalytic conversion of NOx on AgCl/Al2O3 catalyst

The rate of NO conversion under UV illumination was evaluated over Ag/Al₂O₃ and AgCl/Al₂O₃ catalysts at room temperature. The AgCl/Al₂O₃ catalyst is highly active for the conversion of NO_x. The conversion is enhanced in the presence of O₂ and further enhanced when oxygen coexists with hydrocarbons. Diffuse reflectance spectra of AgCl/Al₂O₃ and Ag/Al₂O₃ show an absorption band at 250 nm, and a weak and broad band at 230 nm, respectively. The high photocatalytic NO_x conversion is achieved over the AgCl/Al₂O₃ catalyst. The conversion level of NO_x is maintained above 60% over 5 h in the presence of O₂ and hydrocarbons under UV-irradiation. The absorption band at 250 nm is ascribed to the band gap energy of crystallized AgCl particles on Al₂O₃. These results suggest that high photocatalytic NO_x conversion proceeds on crystallized AgCl particles formed on Al₂O₃.     

TiO_2掺杂CuMnCe/Al_2O_3催化剂对甲烷催化燃烧脱氧反应的影响

以掺杂了不同TiO_2含量的Al_2O_3作为载体,通过等体积浸渍法制备了一系列不同TiO_2含量的CuMnCe/TiO_2-Al_2O_3催化剂,用BET、H_2-TPR、XRD和XPS表征技术对催化剂物理化学性质进行表征,并考察了催化剂在含甲烷气脱氧反应中的催化性能。结果表明,在载体中添加TiO_2对催化剂活性组分的晶相结构和分散度没有明显影响;但有效改善了Al_2O_3载体抗烧结能力;增加了CuMnCe/Al_2O_3催化剂表面Ce~(3+)/(Ce~(3+)+Ce~(4+))的相对含量,从而提高了活性氧的移动性,且使催化剂表面可氧化还原物种含量和表面吸附氧Osur/(Osur+Olatt)的含量增多。有效改善了催化剂在含甲烷气催化燃烧脱氧上的催化活性。其中,CuMnCe/4%TiO_2-Al_2O_3表现出最优的催化活性,在387℃时可使含甲烷气中氧气的转化率达到100%。     

丙烷在Ce-Fe/Al2O3/cordierite上选择性催化还原NO

利用凝胶溶胶法和浸渍法制备了Ce-Fe/Al₂O₃/cordierite催化剂,实验研究了其催化丙烷选择性还原NO的特性。结果表明,当铈的负载量从1%增加至5%时,Ce-Fe/Al₂O₃/cordierite的C₃H₈-SCR性能先增强后减弱,3.5Ce-Fe/Al₂O₃/cordierite具有最佳的脱硝性能,在有氧条件下,600℃时可实现96.5%的脱硝效率。Ce的加入能够提升Fe/Al₂O₃/cordierite催化剂的抗硫性能。烟气中通入0.02%的SO₂后,3.5Ce-Fe/Al₂O₃/cordierite催化丙烷还原NO的转化率始终维持在93%,而没有经过Ce修饰的Fe/Al₂O₃/cordierite的NO转化率从88%下降为80%左右。利用XRD、N₂吸附-脱附、SEM、H₂-TPR、吡啶吸附红外光谱等手段研究了催化剂的物理化学性质。结果表明,加入助剂铈能与Fe形成了固溶体,增加催化剂表面Lewis酸浓度和氧化还原能力,从而提高了催化丙烷还原NO的性能。过多的铈引入会减少Fe₂O₃结晶体的形成,不利于在C₃H₈-SCR反应中形成NO₂/NO₃^-物种,从而导致NO还原效率下降。     

Significant enhancement in water resistance of Pd/Al2O3 catalyst for benzene oxidation by Na addition

Appropriate Na addition led to the formation of well-dispersed metallic Pd particles, which facilitated oxygen adsorption. Proper Na addition further promoted the transformation of absorbed water into liable surface oxygen species and improved the mobility of the lattice oxygen species, which contributed to enhanced catalytic activity and water resistance.     

Oxygen species on NiO/Al2O3 and their reactivities

Oxygen species on fresh and treated NiO/Al₂O₃ and their activities for oxidation of ethane and ethylene were investigated using catalytic property measurements, ethane and ethylene pulse experiments and O₂–TPD–MS experiments. The results revealed that there are two kinds of active oxygen species (the more active one and the less active one) on fresh NiO/Al₂O₃ catalyst, but there is only one active oxygen species, the less active one, on treated NiO/Al₂O₃ catalyst. The more active oxygen species can convert ethane or ethylene to carbon dioxide by one step while the less active one can only convert ethane to ethylene, but cannot convert ethane and/or ethylene to carbon dioxide. The more active oxygen species can be removed from the catalyst by heating from 350 to 850 °C. The amounts of desorption oxygen on the catalysts are proportional to their selectivity to carbon dioxide.     

ZrO2修饰Al2O3纳米片负载钴催化剂的制备及其费托反应性能研究

通过水热法合成了Al₂O₃纳米片（Al₂O₃-CN）,采用浸渍法制备20%（质量分数）钴基催化剂,并应用于费托合成反应。制备的Al₂O₃-CN（226 m²/g）与商业氧化铝（Al₂O₃-C,249 m²/g）具有相近的比表面积,但Al₂O₃-CN孔尺寸分布更加集中。浸渍钴后,与Co/Al₂O₃-C催化剂相比,Co/Al₂O₃-CN催化剂表现出较高的还原度及更均匀的钴颗粒粒径分布。因此,Co/Al₂O₃-CN催化剂表现出更高的CO转化率和低的甲烷选择性。为了进一步提高Co/Al₂O₃-CN的催化性能,采用不同含量ZrO₂对Al₂O₃-CN进行修饰。表征结果表明,随着ZrO₂修饰量的增加,Al₂O₃-CN载体比表面积变化不明显,孔体积和孔径增大;相对应催化剂的钴颗粒粒径减小,活性位点数目增加。在相同反应条件下,经ZrO₂修饰催化剂CO转化率进一步提高,甲烷选择性降低。     

Promoting Effects of Iron on CO Oxidation over Au/TiO2 Supported Au Nanoparticles

Fe-doped TiO₂ supported gold nanoparticles as high-performance CO oxidation catalysts were prepared. XRD data revealed that TiO₂ support was in an anatase phase. After calcination at 300℃, the sample showed nanotube structure, and the size of gold nanoparticles was 3.1 nm. When calcined at 500℃, most nanotubes broke, and gold nanoparticles grew up to 5.9 nm. XPS spectrum indicated the presence of Fe in the +3 oxidation state. Au/Fe-TiO₂(Au:1.44%, Fe:1.35%) calcined at 300℃ possessed the best catalytic activity, and it could completely convert CO at 25℃. The temperature of 100% CO conversion(T_100%) of Fe-free catalyst was 40℃. After the catalysts were stored at room temperature for 7 d, T_100% of Au/Fe-TiO₂ increased from 25℃ to 30℃, while T_100% of Fe-free catalyst increased from 40℃ to 80℃. The catalytic activity and storage stability of Au/TiO₂ could be improved by Fe-doping. The increase of specific surface area, generation of oxygen vacancies and new adsorption sites, depression of the growth of gold nanoparticles, and strong metal-support interaction were responsible for the promoting effect of iron on the catalytic performance of Au/TiO₂ for CO oxidation.     

OMS-2/Al2O3/堇青石整体式催化剂的制备及其催化性能研究

以Al₂O₃/堇青石蜂窝陶瓷为载体,氧化锰八面体分子筛(OMS-2)为活性组分,采用涂覆法制备了系列整体式催化剂。考察了黏合剂种类和活性组分涂覆次数对二甲醚(DME)催化燃烧性能的影响,并对催化剂进行XRD、BET、SEM、H₂-TPR、O₂-TPD等表征。结果表明,以甲氧基聚乙二醇为黏合剂经一次涂覆制备的整体式催化剂的性能最佳,活性组分OMS-2以相互交织的簇体均匀分布在载体上,并与Al₂O₃之间存在较强的相互作用。涂层的添加有效增加了催化剂的比表面积,提高了催化剂的性能,最佳催化活性t₉₀为257 ℃。     

Ce含量对Ni-Ce/Al_2O_3催化剂结构及浆态床CO甲烷化性能的影响

以γ-Al2O3为载体,采用等体积浸渍法制备了不同Ce含量的Ni-Ce/Al2O3催化剂,并考察了其浆态床CO甲烷化反应性能。借助XRD、BET、H2-TPR及CO-TPD等对催化剂进行了表征分析,研究了催化剂的微观结构与甲烷化性能之间的关系。结果表明,助剂Ce的引入能够加强Ni物种与载体之间的相互作用、增强活性组分Ni对CO的吸附能力。随着Ce含量的升高,Ni物种在载体表面的分散度提高、Ni晶粒粒径减小,催化剂的比表面积及与载体相互作用较强的β-NiO相对含量先升后降。催化剂的浆态床甲烷化活性随Ce含量的升高呈现规律性的变化,CO转化率和CH4时空收率先增加后略有下降,当Ce含量为4%(质量分数)时,催化剂甲烷化活性最佳。     

Al2O3助剂对Co/SiC催化剂F-T反应性能的影响

分别采用沉淀法、尿素水解法制备Al₂O₃/SiC复合载体,采用等体积浸渍法制备Co/Al₂O₃-SiC催化剂。结合N₂吸附、XRD、H₂-TPR、XPS等表征手段,研究Al₂O₃助剂对钴基催化剂物相结构、还原行为以及F-T合成性能等的影响。结果表明,氧化铝加入后增强了载体与钴物种之间的相互作用,提高了钴物种的分散度,降低了钴物种的还原度。尿素水解法引入Al₂O₃后,载体与钴物种具有适中的相互作用,表现出较高的反应活性。沉淀法制备的载体负载钴物种后由于较强的金属-载体相互作用,表现出较优的稳定性。     

Pd/Co3O4纳米颗粒负载于Al2O3纳米片高效催化甲烷燃烧

We report an efficient catalyst composed of ternary components prepared by inlaying Pd/Co₃O₄ nanoparticles in alkaline Al₂O₃ nanosheets for catalytic oxidation of methane. Pd/Co₃O₄ inlaid in alkaline Al₂O₃ exhibited a higher ability to break the C-H bond of methane than Pd/Co₃O₄ supported on SiO₂, ZrO₂, CeO₂, and acidic or neutral Al₂O₃. Our results show more oxygen vacancies and higher amounts of surface adsorbed oxygen on the surface of Pd/Co₃O₄/alkaline Al₂O₃ than on other catalysts, which is responsible for methane activation and conversion. Further, the Pd/Co₃O₄/alkaline Al₂O₃ catalyst can almost restore to its initial value in the absence of water when 5% (volume fraction) vapor water was cut off, although a decrease in activity occurred when water vapor was introduced to the reaction system. Even under a condition similar to the exhaust of a lean-burn natural gas engine, the catalytic performance of the Pd/Co₃O₄/alkaline Al₂O₃ catalyst is excellent, that is, methane could be completely converted when the sample temperature in the reaction atmosphere was ramped to 400℃.     

低温下Pt/Al_2O_3和Pd/Al_2O_3光辅助乙二醇水相重整制氢研究

采用浸渍还原法制备了氧化铝负载的Pt和Pd纳米颗粒催化剂,用于光辅助乙二醇水相重整制氢反应。结果表明,光照能够有效降低乙二醇水相重整制氢的活化能,Pt/Al_2O_3比Pd/Al_2O_3具有更高的H_2转换频率(TOF)和更低的CO选择性。采用XRD、TEM、UV-vis等技术对催化剂的结构和形貌进行了表征,原位漫反射红外光谱(DRIFTS)表明,光照能促进乙二醇分子O-H键的断裂。理论计算表明,Pt/Al_2O_3催化乙二醇重整制氢反应产物中较低的CO选择性主要归因于CO在Pt表面较小的反应能垒,能够较快与H_2O解离的O反应生成CO_2。     

二甲基二硫醚对Ni/Al_2O_3催化剂加氢性能的影响

考察了二甲基二硫醚(CH3SSCH3)对Ni/Al2O3催化剂上苯、环己烯和苯乙烯加氢活性的影响,并采用BET、XRD、H2-TPR、XPS、SEM和EA等手段对催化剂进行表征。实验结果表明,在CH3SSCH3存在下,Ni/Al2O3催化剂对苯和环己烯加氢迅速失活,且环己烯加氢对CH3SSCH3的耐硫性要略强于苯加氢,而苯乙烯中共轭烯烃的加氢转化率则维持100%长时间不变。CH3SSCH3的影响顺序为芳环单烯烃共轭烯烃。此外,通过设计实验研究了CH3SSCH3对催化剂的毒化机理,发现CH3SSCH3分子首先吸附在催化剂的表面,并发生氢解生成甲烷随尾气逸出,故CH3SSCH3分子中碳对催化剂的失活影响较小,而留下的硫原子则与镍活性组分发生相互作用,毒化催化剂。     

Study of an iron-based Fischer–Tropsch synthesis catalyst incorporated with SiO2

The effect of adding SiO₂ to a precipitated iron-based Fischer–Tropsch synthesis (FTS) catalyst was investigated using N₂ physical adsorption, H₂ differential thermogravimetric analysis, temperature-programmed reduction/desorption (TPR/TPD) and Mössbauer spectroscopy. The FTS performances of the catalysts with or without SiO₂ were compared in a fixed bed reactor. The characterization results indicated that SiO₂ facilitates the high dispersion of Fe₂O₃ and significantly influences the Fe/Cu and Fe/K contacts, which play an important role in the surface basicity, reduction and carburization behaviors, as well as the FTS performances. The incorporation of SiO₂ enhances the Fe/Cu contact, further enlarges the H₂ adsorption and promotes the reduction of Fe₂O₃ → FeO_x, while the transformation of FeO_x → Fe is suppressed probably due to the strong Fe–SiO₂ interaction. SiO₂ indirectly weakens the surface basicity and severely suppresses the carburization and CO adsorption of the catalyst. In the FTS reaction, it was found that SiO₂ decreases the FTS initial activity but improves the catalyst stability. Due to the lower surface basicity than the catalyst without SiO₂, the catalyst incorporated with SiO₂ has higher selectivity to light hydrocarbons and methane and decreased selectivity to the olefins and heavy hydrocarbons.     

Fe2O3/Al2O3氧载体用于甲烷化学链燃烧：负载量与制备方法的影响

以不同方法制备了系列Fe₂O₃/Al₂O₃氧载体,采用XRD、H₂-TPR、CH₄-TPR、O₂-TPD和BET等分析技术对氧载体进行了表征。研究了不同Fe₂O₃负载量氧载体的甲烷化学链燃烧性能,考察了不同制备方法对Fe₂O₃/Al₂O₃氧载体结构、反应性和产物选择性的影响。结果表明,Fe₂O₃负载量对氧载体活性及产物中CO₂选择性的影响较大,负载量较低时氧载体活性较低且引起甲烷部分氧化产物CO含量增加。制备方法亦对氧载体与甲烷的反应活性有所影响,整体上共沉淀法制备的质量分数60％Fe₂O₃/Al₂O₃氧载体具有较高的氧化活性和化学链循环稳定性。其在反应温度850℃、反应时间15 min、30次循环后甲烷转化率及产物中CO₂选择性均未见明显降低。     

KF/Al2O3催化剂上苯脲醇解合成苯氨基甲酸甲酯的研究

采用浸渍法制备负载KF固体碱催化剂,应用于苯脲和甲醇制备苯氨基甲酸甲酯的反应,考察了氧化物载体、卤化钾种类对催化剂性能的影响,KF/Al₂O₃催化剂显示出良好的催化活性和苯氨基甲酸甲酯的选择性。通过对KF/Al₂O₃催化剂中KF的负载量和催化剂焙烧温度的研究发现,在500 ℃焙烧4 h、负载质量分数50%KF的催化剂能够更好地促进MPC生成,苯脲转化率和苯氨基甲酸甲酯选择性分别达到96.5%和86.3%。XRD分析表明,KF与Al₂O₃之间存在较强的相互作用,部分转化为K₃AlF₆。KF与K₃AlF₆分别对甲醇的活化和苯脲的选择性起促进作用,两者的协同效应共同促进了目标产物苯氨基甲酸甲酯的生成。     

Co/Fe/Al2O3/cordierite催化C3H6选择性还原NO的实验研究

采用溶胶凝胶法和浸渍法制备了负载于蜂窝陶瓷上的Co/Fe/Al₂O₃/cordierite催化剂,在陶瓷管流动反应器上对其催化C₃H₆选择性还原NO的性能进行了测试。结果表明,该催化剂表现出最优脱硝性能,在模拟烟气条件下,当反应温度为550 ℃时可实现97%的脱硝效率。Co的引入可显著增强Fe/Al₂O₃/cordierite催化剂抗SO₂和H₂O的能力。在模拟烟气中同时引入0.02% SO₂和3% H₂O后,1.5Co/Fe/Al₂O₃/cordierite的脱硝性能受影响甚微,当反应温度高于500 ℃时1.5Co/Fe/Al₂O₃/cordierite催化C₃H₆还原NO的效率均可达到90%以上;相比之下,未经Co修饰的催化剂Fe/Al₂O₃/cordierite脱硝性能受到了严重的抑制,在整个反应温度区间（200-700 ℃）内,其催化C₃H₆还原NO的效率最高不足50%。XRD和SEM表征结果表明,经过适量的Co修饰后的1.5Co/Fe/Al₂O₃/cordierite表面变得更疏松,且形成了以钴铁和钴铝双金属氧化物为主要成分的球状晶粒。H₂-TPR结果表明,相比于Fe/Al₂O₃/cordierite,1.5Co/Fe/Al₂O₃/cordierite有更好的低温还原性能。Py-FTIR结果表明,Co的引入可使催化剂表面的Lewis酸明显增加,且生成了Brønsted酸。N₂吸附-脱附表征结果表明,Co可增大催化剂的比表面积。     

铝源对Ni/Al2 O3催化剂结构及其CO2-CH4重整性能的影响

以三种不同铝源采用溶液燃烧法制备了系列Ni/Al_2O_3催化剂,通过XRD、H_2-TPR、NH_3-TPD、N_2吸附-脱附、TGDTG和TPH等分析方法对反应前后催化剂进行了表征,研究了铝源对Ni/Al_2O_3催化剂结构、表面性质及其CO_2-CH_4重整性能的影响。结果表明,以Al(NO_3)_3·9H_2O为铝源制备的NiNO-AlNO催化剂比表面积较大,达102 m~2/g;高温还原峰面积大,峰型更为弥散;且载体Al_2_O_3具有一定的结晶性。而以Al_2(SO_4)_3·18H_2O和AlCl_3·6H_2O为铝源制备的NiNO-AlSO和NiNO-AlCl催化剂,其载体以无定型Al_2O_3存在,活性组分Ni晶粒粒径大、分散性差,还原峰面积较小,与载体的相互作用较弱。其中,由于硫酸铝较为稳定,需要在更高温度下才能转化为Al_2O_3,且所制备NiNO-AlSO催化剂中残留有含硫物质,使得其表面酸性较强。评价结果显示,NiNO-AlNO催化剂活性较高,稳定性好,CH4转化率为31.21%,CO_2转化率为48.97%。积炭分析结果发现,NiNO-AlNO催化剂表面积炭量最少,沉积炭主要以无定型态存在,具有良好的抗积炭性能。     

Ni-Mo/Al_2O_3催化剂上硫转移反应的研究

制备了以γ-Al2O3为载体的Ni-Mo催化剂,并用于FCC汽油的加氢硫转移反应。对Ni-Mo/Al2O3催化剂上的硫转移反应机理进行了研究,考察了不同反应条件对硫转移反应的影响。实验结果表明,硫醇与烯烃的反应在催化剂表面的加氢活性位上进行,小分子的硫醇发生加氢脱硫,生成吸附态H2S,吸附态的H2S与烯烃反应,生成大分子硫醇和硫醚;另外小分子硫醇还可直接与烯烃发生反应,生成硫醚。提高反应温度、压力、氢油比或降低空速,均可提高催化剂的硫转移反应活性,轻质硫转化率得到明显提高,且单烯选择性还能维持在98%左右。