Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

TiO2-Al2O3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO₂-Al₂O₃复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H₂原位还原法制备. 通过N₂吸附（BET）、X射线衍射（XRD）、透射电镜（TEM）、程序升温还原（TPR）,X射线光电子能谱（XPS）和等离子体发射光谱（ICP-AES）表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能. 结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al₂O₃的孔特征,具有较大的比表面积和较宽的孔分布,TiO₂主要以表面富集的形式分散在管状的γ-Al₂O₃表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni₂P和Ni₁₂P₅;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO₂趋于在块状的Al₂O₃表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni₂P. 不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n（Ti）/n（Al）=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340 ℃,3 MPa,氢油体积比500,液时空速3 h^-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

镍基催化剂上稻草水蒸气重整制富氢合成气

采用浸渍法制备了SiO₂, γ-Al₂O₃, CaO和TiO₂负载的Ni催化剂, 以及不同MgO含量的MgO-7.5%Ni/γ-Al₂O₃催化剂,利用X射线衍射和N₂吸附-脱附技术表征了催化剂的结构,在固定床反应器上评价了它们在稻草水蒸气催化重整制合成气反应中的催化性能,考察了反应条件对催化剂性能的影响.结果表明, 以γ-Al₂O₃为载体时Ni催化剂活性最高,其中7.5%Ni/γ-Al₂O₃催化剂的H₂收率可达1071.3ml/g,H₂:CO的体积比为1.4:1;同时,MgO的添加进一步提高了该催化剂的性能,当MgO含量为1.0%时,H₂收率可达1194.6ml/g,H₂:CO体积比可达3.9:1.可见MgO的加入促进了Ni基催化剂上稻草水蒸气催化重整制合成气反应的进行,同时使得合成气中CO发生水-汽转换反应,从而大大提高了合成气中H₂含量.     

二苯并噻吩和吲哚在NiMoS/γ-Al2O3上加氢脱硫和加氢脱氮反应的相互影响

在固定床高压微反装置上考察了预硫化型NiMoS/γ-Al2O3催化剂上二苯并噻吩（DBT）加氢脱硫（HDS）反应和吲哚加氢脱氮（HDN）反应之间的相互影响。结果表明,吲哚对DBT的加氢脱硫反应具有抑制作用,其中对加氢路径（HYD）比对氢解路径（DDS）的抑制作用强,温度升高后,吲哚的抑制作用减弱。吲哚对DBT加氢脱硫反应的抑制作用源于吲哚及其HDN反应的中间产物在活性位上的竞争吸附。DBT和原位生成的H2S促进了催化剂表面硫阴离子空穴（CUS）向B酸位的转化,从而提高1,2-二氢吲哚（HIN）分子中C(sp3)—N键的断裂能力,使得吲哚的转化率和产物中邻乙基苯胺（OEA）的相对含量增大。HDN活性相的形成虽然需要硫原子的参与,但是活性相的保持并不需要大量的硫原子,较高含量硫化物存在时加氢活性位减少,不利于脱氮反应。     

Heterogeneous Uptake of Hydrogen Peroxide on Mineral Oxides

The interaction of mineral oxides (α-Al₂O₃, MgO, Fe₂O₃, and SiO₂) with hydrogen peroxide was investigated using the Knudsen cell reactor. The initial reactive uptake coefficients for the commercially available powders are measured as (1.00±0.11)×10^-4 for α-Al₂O₃, (1.66±0.23)×10^-4 for MgO, (9.70±1.95)×10^-5 for Fe₂O₃, and (5.22±0.9)×10^-5 for SiO₂. These metal oxide powders exhibit some catalytic behavior toward the decomposition of hydrogen peroxide excluding SiO₂. H₂O₂ can be destroyed on Fe₂O₃ surface and O₂ is formed. The experimental results suggest that the heterogeneous loss on mineral surface can represent an important sink of hydrogen peroxide.     

Hydrogenation of acetone on technetium catalysts

The catalytic properties of supported mono- and bimetallic catalysts of the Tc/support, M/support, and M-Tc/support types (M=Pt, Pd, Rh, Ru, Ni, Re, Co; supports are γ-Al₂O₃, MgO, SiO₂) were investigated in the acetone hydrogenation. The main products of this reaction are isopropyl alcohol and propane. The catalytic activity in the acetone hydrogenation of the metals studied decreases in the consequence Pt>Tc≈Rh>Pd>Ru >Ni≈Re>Co (with γ-Al₂O₃ as the support). The influence of support nature on the catalytic activity was investigated for the Rh−Tc system as an example. A nonadditive increase in the catalytic activity of Rh−Tc/γ-Al₂O₃ in comparison with monometallic catalysts was found. The state of the surface of the catalysts was characterized by the UV-VIS diffuse reflectance spectra. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 3, pp. 414–417, March, 1998.     

Propane combustion over supported Pd catalysts

We prepared Pd catalysts supported on various metal oxides, viz. γ-Al₂O₃, α-Al₂O₃, SiO₂–Al₂O₃, SiO₂, CeO₂ and TiO₂ by an incipient wetness method and applied them to propane combustion. Several techniques: N₂ physisorption, inductively coupled plasma-atomic emission spectroscopy (ICP-AES), CO chemisorption, temperature-programmed reduction (TPR) and temperature-programmed oxidation (TPO) were employed to characterize the catalysts. Pd/SiO₂–Al₂O₃ showed the least catalytic activity at high temperatures among Pd catalysts supported on irreducible metal oxides, viz. SiO₂, Al₂O₃ and SiO₂–Al₂O₃. Pd/γ-Al₂O₃ was much superior for this reaction to Pd/α-Al₂O₃. The Pd catalyst supported on reducible metal oxides (CeO₂ and TiO₂) with a less specific surface area showed the higher catalytic activity compared with that supported on reducible metal oxides with a higher specific surface area, even though the former had a less Pd dispersion than the latter. In the case of Pd/SiO₂–Al₂O₃, the initially reduced Pd catalyst was superior to the fully oxidized one. The oxidation of metallic Pd occurred in the presence of O₂ with increasing reaction temperature, which resulted in the change in the catalytic activity.     

不同磷含量对NiMoP/Al2O3加氢处理催化剂的影响

采用NiMoP浸渍液浸渍载体γ Al₂O₃制备了不同磷含量的NiMoP/Al₂O₃加氢处理催化剂。为了研究磷对该系列催化剂活性相结构的影响,用二苯并噻吩（DBT）和喹啉为模型化合物,考察了催化剂的加氢脱硫（HDS）和加氢脱氮（HDN）性能。结果表明,添加适当的磷能够提高催化剂的HDS和HDN活性,但是高含量的磷能显著的降低催化剂的催化性能。通过对催化剂进行XRD和HRTEM表征发现,添加磷能够增加MoS2的堆积层数以及Ⅱ型“Ni-Mo-S”相的相对含量,这是因为在制备过程中添加磷降低了活性组分与载体之间的相互作用。     

Study of CuCl2 Supported on SiO2 and Al2O3

The nature and stability of surface species of CuCl₂ supported on α-Al₂O₃, γ-Al₂O₃, and SiO₂ were investigated by using X-ray diffraction techniques and reflectance spectroscopy. No specific chemical interaction of CuCl₂ is observed on an inert α-Al₂O₃ support, as opposed to hydrated carriers as SiO₂ and γ-Al₂O₃. On these supports the coordination sphere of Cu²⁺ consists of surface groups (OH^? or O^? at drying and activation, resp.), H₂O and Cl^?, with the H₂O ligands decreasing in concentration in the process of impregnation, drying and calcination. γ-Al₂O₃ samples, calcined at 400°C, show γ-Cu₂(OH)₃Cl as opposed to CuAl₂O₄ at higher temperatures. The absence of Cu₂(OH)₃Cl on SiO₂-supported samples is related to the acid-base characteristics of the carriers. The various supports can be arranged in the following order of stability of the complexes formed: γ-Al₂O₃ > SiO₂ ? -Al₂O₃.     

Simulation of heterogeneous catalysts and catalytic processes using the density functional method

The review is devoted to the use of high-level quantum-chemical calculations by the density functional method for the simulation of heterogeneous catalytic systems based on transition metals. The following problems are considered: (1) the development of methods for simulating metal particles supported on the surfaces of ionic and covalent oxides; (2) the calculation of the properties of individual transition metal atoms and small clusters adsorbed on the surfaces of MgO, α-Al₂O₃, γ-Al₂O₃, and various modifications of SiO₂ and in the pores of zeolites; (3) the mechanisms of hydrogen activation and acrolein hydrogenation on the metallic and partially oxidized surface of silver; and (4) the mechanism of formation of carbon residues upon the decomposition of methanol on nanosized Pd particles.     

Rhodium-technetium catalysts in the dehydrogenation of cyclohexane

The catalytic properties of a Rh-Tc/support (-Al₂O₃, SiO₂, or MgO) system in the dehydrogenation of cyclohexane have been investigated. A nonadditive increase in the catalytic activity of bimetallic catalysts in comparison with monometallic systems has been established. This effect depends on the ratio of the amounts of the supported metals and on the nature of the support. Diffuse reflectance spectra showed the presence of ionic forms of the metals in the bimetallic catalysts. Analysis of the catalytic and optical properties allowed one to draw the conclusion that the synergistic effect is explained by the formation of Rh_xTc_y clusters.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 9, pp. 1563–1566, September, 1994.     

Effect of the support on cobalt carbide catalysts for sustainable production of olefins from syngas

Co₂C-based catalysts with SiO₂, γ-Al₂O₃, and carbon nanotubes (CNTs) as support materials were prepared and evaluated for the Fischer-Tropsch to olefin (FTO) reaction. The combination of catalytic performance and structure characterization indicates that the cobalt-support interaction has a great influence on the Co₂C morphology and catalytic performance. The CNT support facilitates the formation of a CoMn composite oxide during calcination, and Co₂C nanoprisms were observed in the spent catalysts, resulting in a product distribution that greatly deviates from the classical Anderson-Schulz-Flory (ASF) distribution, where only 2.4 C% methane was generated. The Co₃O₄ phase for SiO₂- and γ-Al₂O₃-supported catalysts was observed in the calcined sample. After reduction, CoO, MnO, and low-valence CoMn composite oxide were generated in the γ-Al₂O₃-supported sample, and both Co₂C nanospheres and nanoprisms were identified in the corresponding spent catalyst. However, only separated phases of CoO and MnO were found in the reduced sample supported by SiO₂, and Co₂C nanospheres were detected in the spent catalyst without the evidence of any Co₂C nanoprisms. The Co₂C nanospheres led to a relatively high methane selectivity of 5.8 C% and 12.0 C% of the γ-Al₂O₃- and SiO₂-supported catalysts, respectively. These results suggest that a relatively weak cobalt-support interaction is necessary for the formation of the CoMn composite oxide during calcination, which benefits the formation of Co₂C nanoprisms with promising catalytic performance for the sustainable production of olefins via syngas.     

Calorimetric Characterization of Surface Reactivity of Supported Ga2O3 Catalysts

The surface properties of supported gallium oxide catalysts prepared by impregnation of various supports (γ-Al₂O₃, SiO₂, TiO₂, ZrO₂) were investigated by adsorption microcalorimetry, using ammonia and water as probe molecules. In the case of acidic supports (γ-Al₂O₃, ZrO₂, TiO₂), the acidic character of supported gallium catalysts always decreased in comparison with gallium-free supports; on very weakly acidic SiO₂, new acidic centers were created when depositing Ga₂O₃. The addition of gallium oxide decreased the hydrophilic properties of alumina, titania and zirconia, but increased the amount of water adsorbed on silica. The catalytic performances in the selective catalytic reduction of NO by C₂H₄ in excess oxygenwere in the order Ga/Al₂O₃>Ga/TiO₂>Ga/ZrO₂>>Ga/SiO₂. This order is more related to the quality of the dispersion of Ga₂O₃ on the support than to the global acidity of the solids. This revised version was published online in July 2006 with corrections to the Cover Date.     

Catalytic epoxidation of alkenes over supported manganese oxide with hydrogen peroxide: effect of supports and manganese loading

Manganese oxides supported on γ-Al₂O₃, amorphous SiO₂, MCM-41, and TiO₂ prepared by an impregnation method were used as heterogeneous catalysts for epoxidation of alkenes with 30 % H₂O₂ in the presence of NaHCO₃ aqueous solution. The effect of support and manganese loading on their activity was studied. The 1.3-MnO _x /γ-Al₂O₃ exhibited superior epoxidazing activity of styrene, compared with other supported MnO _x . Hydrogen temperature-programmed reduction, UV–vis and ESR analyses suggested that Mn²⁺ (catalytic activity species) dominated in 1.3 % MnO _x /γ-Al₂O₃ due to a strong interaction between MnO _x and γ-Al₂O₃. Recycling studies showed the catalyst was a heterogeneous one and retained its activity after recycling four times.     

Activity of palladium sulfide catalysts in the reaction of gas-phase hydrogenation of 2-methylthiophene

In the interaction of hydrogen with 2-methylthiophene in the gas phase over palladium sulfide catalysts at 180–260?C and 0.1–0.8 MPa, the saturation of the thiophene ring resulting in 2-methylthiolane and the hydrogenolysis of 2-methylthiophene occurs. When the conversion is lower than 60%, these reactions occur independently; at higher conversions, methylthiolane also undergoes hydrogenolysis. The specific catalytic activity of PdS supported on γ-Al₂O₃, TiO₂, and carbon and without support is much lower in the hydrogenation of 2-methylthiophene than the activity of PdS supported on SiO₂, aluminosilicate, and zeolite HNaY having strong Brönsted acid surface sites.     

Effect of oxides on the activity of Co-carbonyl catalysts for hydrocarbon synthesis from CO and H2

The effect of Zr, Mg, and Mn oxides on the activity and selectivity of Fischer-Tropsch catalysts prepared under mild conditions by supporting cobalt carbonyl (SiO₂, SiO₂-Al₂O₃, and -Al₂O₃) is studied. The activating action of the additives is caused by their reaction with the support and depends significantly on its nature.Translated from Izvestiya Akademii Nauk SSSR, Seriya Khimicheskaya, No. 11, pp. 2425–2428, November, 1989.     

选择氧化物载体调变乙醇重整和1,3-丁二烯加氢反应双金属催化剂

研究了不同载体负载的Pt-Ni双金属和单金属催化剂上乙醇重整和1,3-丁二烯加氢反应性能, 以考察氧化物载体对双金属结构和催化活性的影响. 所用的氧化物载体包括γ-Al₂O₃, SiO₂, TiO₂, CeO₂以及高比表面积(HSA)和低比表面积(LSA)ZrO₂. 采用共浸渍法制备催化剂, 用CO化学吸附、透射电镜和扩展X射线吸收精细结构光谱进行催化剂表征, 采用傅里叶变换红外间歇反应器进行化学反应评价. 对于乙醇重整反应, Pt-Ni双金属催化剂优于单金属催化剂, Pt-Ni双金属催化剂活性顺序为TiO₂ > SiO₂ > γ-Al₂O₃ ≈ LSA-ZrO₂ > CeO₂ > HSA-ZrO₂. 对于1,3-丁二烯加氢反应, 在SiO₂, TiO₂和HSA-ZrO₂载体上双金属催化剂优于单金属催化剂, Pt-Ni双金属催化剂活性顺序为SiO₂ > CeO₂ > γ-Al₂O₃ > LSA-ZrO₂ > HSA-ZrO₂ ≈ TiO₂.     

Ammonia synthesis by means of plasma over MgO catalyst

Ammonia synthesis from H₂-N₂ mixed gas was studied at room temperature in a glow-discharge plasma in the presence of metals or metal oxides. Magnesia (MgO) and calcia (CaO), which are oxides with solid basicity, revealed catalytic activity in the plasma synthesis of ammonia, although they are catalytically inactive in industrial ammonia synthesis. The acidic oxides (Al₂O₃, WO₃, and SiO₂-Al₂O₃) lead to the consumption of the reactant, i.e., the H₂-N₂ mixed gas. No ammonia was isolated. Metal catalysts showed higher activity than the above basic oxides. They have, however, different activities. The reaction was faster over the active materials than over sodium chloride (NaCl) or glass wool or in a blank reactor without any catalyst.     

Marked Effect of Various Supports and Additives Upon Liquid Phase Methanol Reforming with Water over Supported Group 8–10 Metal Catalysts

The support effects (SiO₂, TiO₂, Al₂O₃, MgO, CeO₂ and ZrO₂) as well as addition effect of group 6b and 7b elements were studied over various supported group 8–10 metal catalysts. Basic oxide support improved the selectivity to CO₂ and acidic support suppressed the catalytic activity and selectivity. Among the investigated catalysts Pt–Mo/TiO₂ was the most active catalysts, whereas Ir–Re/SiO₂ was the most selective catalysts for H₂ and CO₂ formation. The mechanism of the liquid phase methanol reforming reaction over silica supported Pt–Ru catalyst was studied by kinetic investigations. The rate of H₂ formation over Pt–Ru/SiO₂ catalysts was more than 20 times faster than that over Pt/SiO₂ catalysts with high selectivity for CO₂ (72.3%), indicating a marked addition effect of Ru. In the case of HCHO–H₂O reaction over Pt–Ru/SiO₂, the H₂ formation rate was five times larger than that in the CH₃OH–H₂O reaction but selectivity to CO₂ was only 4%. On the contrary, in the HCOOCH₃–H₂O and HCOOH–H₂O reactions, both high activity and selectivity were observed over Pt–Ru/SiO₂. These results clearly indicate that the CO₂ formation does not proceed via HCHO decomposition and following water gas shift reaction.     

The complete oxidation of a volatile organic compound (toluene) over supported metal oxide catalysts

The complete oxidation of a volatile organic compound (toluene) was carried out over oxides of various metals (Cu, Mn, Fe, V, Mo, Co, Ni and Zn) supported with -Al₂O₃ catalyst. It was found that Cu/-Al₂O₃ was the best catalyst among them. With increasing calcination temperature, the specific surface areas and the surface oxygen of the catalyst decreased and, as a result, the catalytic activity decreased. Copper loadings on -Al₂O₃ had an influence on catalytic activity, and it was observed that 5 wt% Cu/-Al₂O₃ catalyst was the most active. Using TiO₂ (rutile) and SiO₂ as support instead of -Al₂O₃, the sequence of copper crystallinity degree with respect to supports was SiO₂ > TiO₂ (rutile) > -Al₂O₃, which was the opposite of the catalytic activity sequence.