火焰原子吸收光谱法测定镍基高温合金中的镉

采用火焰原子吸收光谱法测定镍基高温合金中的镉,样品以硝酸-氢氟酸-水混合溶液(1+1+1)前处理,选择Cd 228.8 nm为分析线进行测定,并通过标准加入法校正基体效应。考察了消解酸的选择,仪器工作参数的调整,基体和共存离子对镉测定的影响。结果表明,镍基高温合金中镉的检出限为0.088μg/g。加标回收率为94.1%~109%,结果的相对标准偏差(RSD,n=8)在0.54%~1.6%。方法操作简便、分析速度快、准确度好,适用于镉含量在0.0001%~0.001%的镍基高温合金中的测定。     

火焰原子吸收光谱法测定镍基高温合金中的镉

采用火焰原子吸收光谱法测定镍基高温合金中的镉,样品以硝酸-氢氟酸-水混合溶液(1+1+1)前处理,选择Cd 228.8nm为分析线进行测定,并通过标准加入法校正基体效应。考察了消解酸的选择,仪器工作参数的调整,基体和共存离子对镉测定的影响。结果表明,镍基高温合金中镉的检出限为0.088μg/g。加标回收率为94.1%～109%,结果的相对标准偏差(RSD,n=8)在0.54%～1.6%。方法操作简便、分析速度快、准确度好,适用于镉含量在0.0001%～0.001%的镍基高温合金中的测定。     

石墨炉原子吸收光谱法测定陶瓷餐具中钡的溶出量

陶瓷餐具样品经硝酸-氢氟酸(3+1)混合溶液微波消解或乙酸(4+96)溶液萃取,采用石墨炉原子吸收光谱法测定其中钡的溶出量。选择灰化温度为1 050℃,原子化温度为2 600℃。萃取法得钡的线性范围为20.0~100μg·L-1,检出限(3S/N)为0.080μg·L-1;消解法得钡的线性范围为10.0~100μg·L-1,检出限(3S/N)为0.029μg·L-1。应用此法分析了陶瓷餐具样品,加标回收率在94.2%~98.8%之间,相对标准偏差(n=5)在2.6%~3.5%之间。     

微波消解石墨炉原子吸收光谱法测定氢化棉籽油中痕量镍

建立了微波消解样品、塞曼扣背景石墨炉原子吸收测定氢化棉籽油中痕量镍的方法。向0.050 0 g氢化棉籽油样品中加入2 m L的硝酸和0.5 m L双氧水,于微波消解仪中消解,用石墨炉原子吸收法测定样品溶液中镍的含量。镍的含量在0.1~50 ng/m L范围内与其吸光度呈良好的线性关系,线性相关系数为0.998 2,检出限为15pg/m L。测定结果的相对标准偏差为2.33%(n=11),样品加标回收率为94%~102%,该方法的测定结果与美国药典法基本一致。该方法样品处理方法快速、简单,背景空白低,测定结果准确、可靠,适合于实际样品分析。     

微波消解-石墨炉原子吸收光谱法测定纳米二氧化钛中痕量砷

建立了微波消解-石墨炉原子吸收光谱法（GF-AAS）测定纳米二氧化钛中痕量杂质元素砷的分析方法。采用由一定浓度和比例的氢氟酸、硝酸组成的混合试剂,结合应用高压密闭微波加热技术快速完全消解纳米二氧化钛样品,优选了最佳微波加热控制程序,不仅解决了二氧化钛难消解和待测元素砷高温消解过程中易挥发损失等难点,而且检测溶液酸度低,避免对GF-AAS石墨管的侵蚀。并且,通过基体效应影响实验,优化选择了石墨管类型、石墨炉升温原子化控制程序以及原子吸收光谱仪检测参数,消除热稳定性强的二氧化钛基体对测定易挥发痕量元素砷的影响。方法检出限为0.02μg/L,加标回收率为93.0%~106.0%,相对标准偏差9.4%,与ICP-MS检测方法结果对照一致。     

高分辨电感耦合等离子体质谱法测定镍基单晶高温合金中36种痕量元素

基于高分辨电感耦合等离子体质谱法(HR-ICP-MS)的质谱干扰消除技术,对镍基单晶高温合金中36种痕量元素检测的质谱条件、基体干扰、质谱干扰与同位素选择进行了研究。取样品0.100 0 g,用体积比为3∶1的盐酸-硝酸混合酸10 mL、氢氟酸1 mL溶解,用水定容至250 mL。通过复杂基体质谱干扰计算判定、共存元素干扰消除,确定了待测元素的同位素和分辨模式,将镍基单晶高温合金中痕量元素准确测定的元素种类确定为36种。采用标准加入法进行定量分析,36种痕量元素的检出限(3s)为0.004～6.000μg·L^-1。方法用于分析国际标准物质,得到的测定值与认定值基本一致。方法用于镍基单晶高温合金样品分析,36种痕量元素的检出量为0.000 001 0%～0.018%。     

微波消解-电感耦合等离子体原子发射光谱（ICP-AES）法测定镍基耐蚀合金中镍

采用微波消解法与电感耦合等离子体原子发射光谱(ICP-AES)法相结合的方式,建立了镍基耐蚀合金中镍元素含量的测定方法。试样在浓硝酸和浓盐酸中微波消解后,用电感耦合等离子体原子发射光谱仪在优化的工作参数下测定,结果表明,稀释的消解液可直接用于镍含量的测定,光谱干扰少。对镍基耐蚀合金中镍含量进行多次平行测定,相对标准偏差(RSD,n=7)为0.29%,且测得值与标准值结果一致。对不同的镍基耐蚀合金样品进行加标回收实验,加标回收率在98.5%~102%。标准物质验证实验表明,测得值与标准值一致。     

微波消解ICP-MS法测定锂离子电池石墨负极材料中9种痕量元素

建立微波消解–ICP–MS法测定锂离子电池石墨负极材料中Al,Cr,Cu,Fe,K,Na,Ni,Pb,Zn 9种痕量元素含量的方法。采用硝酸–盐酸体系微波消解样品,稀释后用ICP–MS法测定样品消解溶液中9种痕量元素的含量。在优化仪器工作参数后,采用同位素和He模式克服质谱干扰。9种元素的质量浓度与质谱强度具有良好的线性关系,线性相关系数为0.999 1~0.999 8,检出限为0.132~3.700 mg/kg。加标回收率为98.4%~101.0%,测定结果的相对标准偏差为0.3%~3.6%(n=6)。该方法测定结果准确可靠,可用于锂离子电池石墨负极材料中痕量元素的测定。     

微波消解-电感耦合等离子体原子发射光谱(ICP-AES)法测定镍基耐蚀合金中镍

采用微波消解法与电感耦合等离子体原子发射光谱(ICP-AES)法相结合的方式,建立了镍基耐蚀合金中镍元素含量的测定方法。试样在浓硝酸和浓盐酸中微波消解后,用电感耦合等离子体原子发射光谱仪在优化的工作参数下测定,结果表明,稀释的消解液可直接用于镍含量的测定,光谱干扰少。对镍基耐蚀合金中镍含量进行多次平行测定,相对标准偏差(RSD,n=7)为0.29%,且测得值与标准值结果一致。对不同的镍基耐蚀合金样品进行加标回收实验,加标回收率在98.5%～102%。标准物质验证实验表明,测得值与标准值一致。     

微波消解-石墨炉原子吸收光谱法测定固定污染源废气样品中铜、镍、镉的含量北大核心CSCD

用滤筒采集固定污染源废气样品,将滤筒剪碎,置于微波消解管中,加入体积比3∶1的盐酸-硝酸混合液5.0 mL和水20.0 mL,于200℃消解15 min.在所得消解液中加入水10 mL,静置0.5 h进行浸提,过滤,用水定容至50 mL.所得样品溶液采用石墨炉原子吸收光谱法测定其中铜、镍、镉的含量.铜、镍、镉3种元素优化的测定条件如下:灰化温度依次为1100,1200,500℃,灰化时间均为20 s,原子化温度依次为2000,2400,1500℃,原子化时间依次为5,5,4 s.结果表明:铜、镍、镉的质量浓度在一定范围内与其对应的吸光度值呈线性关系,检出限(3.143s)依次为2,3,0.06μg·L^(-1).用此法测定煤飞灰中重金属成分分析标准物质(总量)(RMU010),测定值与认定值基本一致.平行测定某实际煤飞灰样品6次,测定值的相对标准偏差为2.6%~7.0%.采集某固定污染源废气样品7个,按本方法测定,测定值的相对标准偏差小于20%,说明采集方法具有一定稳定性.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.