Pt-H_xWO_3复合电极的制备及其对氧还原的电催化

应用电位扫描法制备3种铂与氢钨青铜(HxWO3)的复合电极,即铂上沉积氢钨青铜(HxWO3/Pt),氢钨青铜上沉积铂(Pt/HxWO3)及铂和氢钨青铜共沉积(Pt-HxWO3).测试结果表明,氢钨青铜能显著提高铂电催化对氧还原的活性,其中以复合电极Pt/HxWO3的电催化活性最高,这可能是因为在玻碳基底上先电沉积氢钨青铜再电沉积铂增加了铂的有效比表面,该电极制备为减少铂用量提供一条有效途径.     

CeO_2/Pt复合电极及其电催化特性

应用恒电位沉积(psd)和电位脉冲沉积(ppd)法在Pt基底制备CeO2/Pt复合电极,用能量色散X射线光谱(EDX)和X射线衍射(XRD)检测CeO2纳米粒子的成分和结构,场发射扫描电子显微镜(FESEM)观察样品形貌.结果表明:CeO2颗粒细小、致密.在KOH溶液中,CeO2/Pt对甲醇氧化和氧还原有电催化作用;若在稀硫酸中溶除CeO2/Pt电极(ppd)的部分CeO2,则电极的电催化作用进一步增强.     

电化学方法制备高分散Pt/CMK-3及其对甲醇电化学催化性能

采用直接电化学还原法在介孔碳(CMK-3)载体上直接电沉积高分散的铂纳米颗粒,制备CMK-3复合铂纳米颗粒电极(Pt/CMK-3)。 通过透射电子显微镜分析发现,铂纳米颗粒非常均匀的分布在CMK-3上,平均粒径约5 nm。 通过循环伏安测试,分析了催化剂不同负载铂含量时氯铂酸的利用率,在理论铂质量分数为20%时,这种方法制备的Pt/CMK-3所使用的氯铂酸的利用率最高,在1 mol/L CH3OH+0.5 mol/L H2SO4溶液中循环伏安测试电流密度达到382 A/g。 在相同实验条件下,Pt/CMK-3电极对甲醇电催化活性远高于Pt/XC-72(炭黑)电极和用常规电沉积方法制备的Pt/CMK-3电极。     

Pt微粒修饰纳米纤维聚苯胺电极对甲醇氧化电催化

以脉冲电流法制备的纳米纤维状聚苯胺(PANI)为Pt催化剂载体，用它制备了甲醇阳极氧化的催化电极Pt/（nano-fibular PANI）.研究结果表明, Pt/（nano-fibular PANI）电极对甲醇氧化具有很好的电催化活性,并有协同催化作用.在相同的Pt载量条件下， Pt/（nano-fibular PANI）电极比Pt微粒修饰的颗粒状聚苯胺电极Pt/(granular PANI)具有更好的电催化活性.此外， Pt的电沉积修饰方法同样影响Pt/（nano-fibular PANI）电极对甲醇氧化的催化活性.脉冲电流法沉积Pt形成的复合电极较循环伏安法电沉积得到的Pt复合电极具有更优异的催化活性.     

金属化聚邻甲苯胺膜修饰电极的性能研究

在聚邻甲苯胺 (POT)膜修饰电极上用电化学法沉积Pt微粒 ,由SEM与XRD表征其表面形态与晶面取向 ,同时研究异丙醇在金属化POT膜电极上的氧化行为 .结果表明 ,Pt在POT膜上的沉积呈现晶面择优取向的现象 ,况且POT质子掺杂后 ,由于电化学活性增强 ,影响了沉积铂微粒的尺寸和粒径分布 .异丙醇的电氧化可发生在POT的电化学活性区 ,当电位大于 0 .70V(SCE)时 ,POT不再呈氧化还原活性 ,异丙醇的电氧化主要在铂微粒上进行 .聚合物不仅作为铂微粒的载体而且自身参加反应 ,这种微异相催化体系需用新的模型描述     

不同介质对Pt/GC电极制备及其性能的影响

应用循环伏安法(CV),扫描电子显微镜(SEM)和电化学原位红外反射光谱(in situFTIRS)研究了不同介质对碳载铂纳米薄膜电极(Pt/GC)的表面结构以及该薄膜电极对甲酸电催化氧化性能的影响.结果表明,使用不同介质的镀铂溶液,均可电沉积出分布较为均匀的Pt粒子,但其尺寸与形貌却相差很大.当以H2SO4作介质,由循环伏安法于玻碳电极上电沉积Pt得到的(Pt/GC1)电极,其Pt粒子粒径约100~200 nm;而在HClO4介质得到的(Pt/GC2)电极,则含有两种Pt微晶:其一是立方体形,粒径约200 nm,其二为菜花状,粒径约400 nm.电化学循环伏安和原位红外反射光谱测试指明,不同介质制备的Pt/GC电极对甲酸的电催化氧化均表现出与本体铂电极(Pt)相类似的特性,即可通过活性中间体或毒性中间体将甲酸氧化至CO2,但不同结构的Pt/GC电极具有不同的电催化活性.进一步以Sb或Pb修饰Pt/GC电极,不仅可以有效地抑制毒性中间体CO的生成,而且还能显著提高其电催化活性.比较本文研究的7种电极,其电催化活性顺序依次为:Sb-Pt/GC2>Pb-Pt/GC2>Pb-Pt/GC1>Sb-Pt/GC1>Pt/GC2>Pt/GC1>Pt.     

铂/普鲁士蓝复合纳米线的合成及电化学传感应用

利用多孔聚碳酸酯膜,采用两步模板电沉积法制备了铂/普鲁士蓝(Pt/PB)复合纳米线。将Pt/PB复合纳米线固定在玻碳(GC)电极上,构建过氧化氢电化学传感器。实验结果表明,Pt/PB复合纳米线对过氧化氢的还原有良好的电催化作用。在电位为-0.1V时,响应电流信号与过氧化氢浓度呈良好的线性关系,线性范围为6.1×10-4～1.8×10-2 mol/L,检出限(S/N=3)为5.0×10-7 mol/L。该修饰电极具有响应速率快、稳定性高、使用寿命长等优点,同时还具有一定的抗干扰能力。     

Pt纳米粒子/Pd纳米线复合材料对乙醇的电催化氧化研究

采用恒电位法在多孔阳极氧化铝模板中电沉积Pd纳米线阵列,再运用循环伏安法在Pd纳米线阵列表面沉积Pt纳米粒子制备出复合纳米材料电极。运用循环伏安法和计时电流法研究了该复合纳米材料电极对乙醇的电催化性能的影响。结果表明,Pt纳米粒子/Pd纳米线复合电极相比于单独的Pd纳米线电极或Pt纳米粒子电极,对乙醇氧化有更高的电催化活性和很好的稳定性。     

自组装纳米金膜上铂微/纳结构电催化剂的制备及性能

基于纳米金(AuNP)表面基团的静电自组装作用制备了多层有序的纳米金超薄膜. 研究了自组装纳米金超薄膜上铂微/纳结构催化剂(Pt/AuNP)的制备过程. 考察了沉积电位和沉积时间对甲酸电氧化活性的影响, 确定了最佳沉积电位为0 V, 最佳沉积时间为600 s. 同时对比考察了Pt/AuNP/PE/GCE, AuNP/PE/GCE和纯Pt电极在0.1 mol/L H2SO4介质中对甲酸电氧化活性以及载体对沉积物形态和甲酸氧化活性的影响. 研究结果表明, 纳米金组装体对铂的电沉积有明显的促进作用; Pt/AuNP/PE/GCE对甲酸的电氧化有很好的电催化性能.     

聚邻苯二胺/铂复合电极的制备及其电催化研究

利用原位聚合原位还原复合法制备了聚邻苯二胺(PoPD)/铂(Pt)复合电极。通过扫描电镜(SEM)、x射线能谱(XRD)、傅立叶变换红外光谱(FTIR)、和交流阻抗(EIS)对其形貌、组成元素和结构等进行了表征。研究了Poly(O-Phenylenediamine)/Platinum电极对甲醇的电催化行为,发现该复合电极对甲醇有良好的电催化性能。与裸铂电极相比,氧化电流高出约4.5倍。通过循环伏安法和计时电量法测定了修饰电极在甲醇溶液中的动力学参数,测得电子转移数为1,扩散系数为8.5687×10-7㎝2/s。     

Electrochemical preparation of effective and low cost catalyst for electrooxidation of ethanol

A nanocatalyst coating was prepared at surface of a glassy carbon electrode by electropolymerization of pyrrole by cycling the electrode potential between ?0.8 and 0.8 V (vs. Ag/AgCl). Then, polypyrrole film was potentiostatically coated with platinum nanoparticles at constant potential of ?0.2 V (vs. Ag/AgCl). The resulting electrode was denoted as GCE/PPy/Pt. This modified electrode was characterized by IR, SEM, TEM and EDX. The electrocatalytic oxidation of ethanol at the GCE/PPy/Pt has been investigated using cyclic voltammetric and chronoamperometric methods. The effects of various parameters on electrocatalytic oxidation of the ethanol, such as the thickness of PPy film, the amount of platinum nanoparticles, ethanol concentration, potential scan rate and working potential limit in anodic direction, were investigated. The kinetic of the ethanol oxidation is discussed on the GCE/PPy/Pt. The stability and reproducibility of this modified electrode were also studied.     

High dispersion and electrocatalytic properties of platinum nanoparticles on graphitic carbon nanofibers (GCNFs)

Highly dispersed platinum nanoparticles were electrodeposited on graphitic carbon nanofibers (GCNFs) by cyclic voltammetry (CV) in 7.7 mM H2PtCl6+0.5 M HCl aqueous solutions. The graphitic carbon nanofibers (GCNFs) used in this paper were grown directly on a graphite disk by chemical vapor deposition (CVD). The micrographs and element composition of Pt/GCNFs/graphite electrode were characterized by scanning electron microscopy (SEM) and electron diffraction spectroscopy (EDS). The electrocatalytic properties of Pt/GCNFs/graphite electrode for methanol oxidation have been investigated by CV and excellent electrocatalytic activity can be observed even at very low platinum loading (md=8.79 microg cm(-2)). The highest mass activity (MA) for methanol oxidation reaches 323 Ag(-1) when Pt/GCNFs/graphite electrode was cycled at a sweep rate of 50 mVs(-1) by CV in 2 M CH3OH+1 M H2SO4 aqueous solutions. This may be attributed to the small particle size and high dispersion of platinum particles coated on GCNFs and shows good potential application in direct methanol fuel cell (DMFC). Additionally, the long-term cycling stability of platinum catalysts was also investigated.     

A Voltammetric Sensor Based on Spinel-Structured Copper Ferrite Nanoparticles Multiwalled Carbon Nanotubes Modified Carbon Paste Electrode for Determination of Dacarbazine

A simple and sensitive method was used to develop a novel sensor for determination of dacarbazine on the surface of multi-walled carbon nanotubes/CuFe₂O₄ nanoparticles modified carbon paste electrode (MWCNTs/CuFe₂O₄/CPE). Cyclic voltammetry, differential pulse voltammetry, chronoamperometry, and electrochemical impedance spectroscopy were used to investigate the electrochemical behavior of dacarbazine at the chemically modified electrode. According to the results, MWCNTs/CuFe₂O₄/CPE showed high electrocatalytic activity for dacarbazine oxidation, producing a sharp oxidation peak current at about +0.80 vs. Ag/AgCl reference electrode at pH 5.0. The peak current was linearly dependent on dacarbazine concentration over the range of 0.10–76.0 μmol L^–1 with the detection limit (3σ) of 0.08 μmol L^?1. In addition, chronoamperometry was also used to determine diffusion coefficient of dacarbazine at MWCNTs/CuFe₂O₄/CPE.     

Application of Carbon Paste Electrode Modified with Carbon Nanofibres/Polyaniline/Platinum Nanoparticles as an Electrochemical Sensor for the Determination of Bezafibrate

The present study deals with the development of an electrochemical sensor for quantitative determination of Bezafibrate (BZF) based on carbon nanofibers/polyaniline/platinum nanoparticles modified carbon paste electrode (CNF/PANI/Pt/CPE). BZF is a fibric acid derivative and is used largely in the treatment of lipid disorders. The nanocomposite was synthesized by in situ polymerization of aniline using ammonium persulphate and platinum nanoparticles were uniformly decorated on the CNF/PANI surface by reducing hexachloroplatinic acid using sodium borohydride. The electrochemical response of BZF at CNF/PANI/Pt/CPE was studied using cyclic voltammetry (CV), differential pulse voltammetry (DPV) and electrochemical impedance spectroscopy (EIS). The above study resulted into significant improvement of the electrochemical signal towards the oxidation of BZF, revealing that the oxidation process is highly favorable at the surface of modified electrode. The anodic peak current I_p (μA) is found to be linearly dependent on BZF concentration in the range of 0.025 μM to 100 μM with a detection limit of 2.46 nM. The practical analytical utilities of the sensor were investigated by performing the experiments on synthetic pharmaceutical formulations, human blood serum and urine samples which offered good recovery, suggesting the high efficacy and authenticity of CNF/PANI/Pt/CPE sensor for BZF determination.     

Electrocatalytic and Simultaneous Determination of Ascorbic Acid,Nicotinamide Adenine Dinucleotide and Folic Acid at Ruthenium(II) Complex‐ZnO/CNTs Nanocomposite Modified Carbon Paste Electrode

This paper describes the development a novel ruthenium(II) complex‐ZnO/CNTs modified carbon paste electrode (Ru(II)/ZnO/CNTs/CPE) for the electrocatalytic determination of ascorbic acid (AA). The objective of this novel electrode modification was to seek new electrochemical performances for the detection of AA, nicotinamide adenine dinucleotide (NADH) and folic acid (FA). The peak potentials recorded were 170, 500 and 830 mV vs. Ag/AgCl/KCl_sat for AA, NADH and FA, respectively. The peak currents were linearly dependent on AA, NADH and FA concentrations using square wave voltammetry (SWV) method at the ranges of 0.008–251, 1.0–650, and 3.0–700 µmol L^?1, with detection limits of 0.005, 0.5, and 1.0 µmol L^?1, respectively.     

Bioelectrocatalytic current based on direct heterogeneous electron transfer reaction of glucose oxidase adsorbed onto multi-walled carbon nanotubes synthesized on platinum electrode surfaces

Multi-walled carbon nanotubes (MWCNTs) were synthesized on platinum plate electrodes by the chemical vapor deposition (CVD) method. The MWCNTs synthesized on the Pt plate (MWCNTs/Pt) electrode were immediately immersed into solutions of glucose oxidase (GOX) to immobilize these enzymes onto the MWCNTs/Pt electrode surfaces. After the GOX was immobilized onto the MWCNTs/Pt electrode, a well-defined catalytic oxidation current was increased from ca. −0.45 V (vs. Ag/AgCl/saturated KCl), which was close to the redox potential of flavin adenine dinucleotide (FAD) as a prosthetic group of GOX under physiological pH values.     

氮掺杂纳米碳块的制备及氧还原的高电化学催化活性

面对全球化的能源危机,燃料电池由于其高效性和可重复使用性成为越来越具有潜力的能量转化设备.阴极发生的氧气还原反应对于燃料电池的性能十分重要,寻找高效的氧还原催化剂在很大程度上可以提高燃料电池的性能.传统的氧还原催化剂是贵金属铂,但是铂的价格十分高,较差的稳定性和选择性限制了它的商业化应用,因此找到一种廉价高效的非贵金属氧还原催化剂来代替铂基催化剂成为目前的研究热点.我们最近发现将纯的三羟甲基氨基甲烷置于管式炉中在800°C下真空烧制2 h,可以简单快捷地得到一种含 N量为4.11%的纳米碳块(标记为 NCNBs-800),该材料可用于催化电化学氧气还原反应.同样情况下在700和900°C下合成的材料标记为 NCNBs-700和 NCNBs-900.采用傅里叶变换红外光谱(FTIR)、X射线光电子能谱(XPS)、扫描电子显微镜(SEM)、X射线衍射(XRD)和电化学旋转圆盘方法与技术对催化剂的成分、形貌和电催化性能进行了表征. SEM表明 NCNBs-800为直径为60 nm的碳块,用 FTIR手段表征了 NCNBs-800的结构变化,三羟甲基氨基甲烷中的–OH和–NH2在高温下发生消去反应,形成了饱和度不同的 C–N键和 C–C键.这些饱和度不同的 N原子和 C原子增加了材料的缺陷结构和活性位点,进一步促进了氧还原反应的催化性能.采用 XPS分析了 NCNBs-800表面的元素,通过对 N 1s进行分峰拟合,发现 NCNBs-800含有能促进氧还原性能的吡啶-N和吡咯-N,特别是吡啶-N,它吸电子的能力很强,从而导致与它邻近的 C原子表面具有一定的正电荷,这些正电荷促进了氧气的吸附和还原,为氧气还原反应提供活性位点,促进氧气还原反应的发生. XRD结果表明,三羟甲基氨基甲烷热解前后的 XRD谱图有明显变化,热解后的三羟甲基氨基甲烷呈现两个宽峰,代表着杂化碳的存在. NCNBs-800的衍射峰强度比 NCNBs-700以及 NCNBs-900大,但是宽度则比 NCNBs-700以及 NCNBs-900小,这表明800°C有利于材料的石墨烯化及碳化过程.电化学阻抗可以表明修饰电极的表面性质,阻抗图中高频处半圆的直径大小代表电子转移阻力,低频处的线性部分代表扩散过程.阻抗数据表明, NCNBs-800的电荷转移电阻可与 Pt/C催化剂相比,但是比裸露的玻碳电极小.这表明 NCNBs-800有较好的导电性和电化学性质. CV曲线表明 NCNBs-800氧还原的起始电位是-0.05 V (vs Ag/AgCl),氧气的还原电位是0.20 V (vs Ag/AgCl),说明 NCNBs-800具有良好的电化学催化性能.旋转环盘电极仪测得的氧还原极化曲线表明,在-0.3 to-0.8 V下的 NCNBs-800氧还原的电子转移数为3.4,过氧化氢产率为52%-35%,表明 NCNBs-800呈现一个提高的四电子过程.稳定性对于燃料电池氧气还原反应也是一个十分重要的性能,通过计时电流技术在电压为-0.2 V下对 NCNBs-800与 Pt/C进行了稳定性测试.结果表明,在2500 s之后 NCNBs-800相对于它的最初催化活性损失为17.56%,而 Pt/C损失了30.71%,从而说明 NCNBs-800的稳定性优于 Pt/C.总之,我们通过一步热解的简易技术制备了一种氮掺杂纳米碳材料,该碳材料具有廉价、高效和容易制备等特点,具有良好的电化学催化性能,有望在燃料电池氧化还原反应中得到大规模应用.     

Polypyrrole/Co-tetraphenylporphyrin modified carbon fibre paper as a fuel cell electrocatalyst of oxygen reduction

A thin-layer of polypyrrole (PPy) film, immobilized with neutral 5,10,15,20-tetraphenylporphyrinato cobalt (II) (Co-TPP), was successfully and uniformly deposited onto mesoporous carbon fibre paper (CFP) via vapor-phase polymerization. The resulting PPy/Co-TPP-modified carbon fibre paper (PPy/Co-TPP-CFP) electrode was characterized by cyclic voltammetry, SEM and EDX-ray mapping. Its electrochemical stability and long-term electrocatalytic performance were investigated in a half-fuel cell testing system. The electrode displayed significant electrocatalytic performance for oxygen reduction at 0.0 V (vs. Ag/AgCl), with notable long-term stability.     

Electrochemical Detection of Hydrazine Based on Electrospun Palladium Nanoparticle/Carbon Nanofibers

In this work, we developed an electrochemical method for the detection of hydrazine based on palladium nanoparticle/carbon nanofibers (Pd/CNFs). Pd/CNFs were prepared by electrospinning technique and subsequent thermal treatments. The electrocatalytic behaviors of Pd/CNFs modified glassy carbon electrode (Pd/CNF‐GCE) for hydrazine oxidation were evaluated by cyclic voltammetry (CV), an obvious and well‐defined oxidation peak appeared at ?0.32 V (vs. Ag/AgCl). The mechanism of the oxidation of hydrazine at Pd/CNF‐GCE was also studied, which demonstrated an irreversible diffusion‐controlled electrode process and a four‐electron transfer involved in the overall reaction. Furthermore, the wide linear range, low detection limit, good reproducibility and excellent storage stability were obtained utilizing differential pulse voltammetry (DPV).     

The role of carbon support morphology in the formation of catalytic layer of solid-polymer fuel cell

The Pt/C catalysts with similar morphology of active catalytic phase (platinum nanoparticles), which were deposited on the supports with different types of carbon structures (Vulkan XC-72 carbon black, Taunit carbon tubes, and Timrex HSAG-300 carbon support with graphite structure), were fabricated by the method of electrochemical dispersion. The effect of the carbon structure type on the electrocatalytic properties of Pt/C catalysts was studied in their operation in the three-electrode cell and in-service in the membrane-electrode assembly of air-hydrogen solid-polymer fuel cell. The Pt/C catalyst based on the Vulkan XC-72 carbon support showed the best performance. The anisotropic shape of Taunit carbon nanotubes and the microstructure of Timrex HSAG-300 carbon support do not allow us to form a catalytic layer with a large active platinum surface area and a structure, which provides an effective ionic transport and mass exchange near the platinum surface.