无酶葡萄糖传感器

利用葡萄糖在镍电极上的电化学氧化．制备了无酶葡萄糖传感器,研究了其电化学氧化机理．并测定了血清中葡萄糖的含量。在较高的pH值和570 mV的电位条件下,镍电极上产生的Ni(Ⅲ)具有氧化剂的作用,能直接氧化葡萄糖为葡萄糖酸内酯,产生的正比于葡萄糖浓度的电流响应可以定量样品中的葡萄糖含量。传感器由镍棒、铂丝对极和Ag/AgCl参比电极构成;对葡萄糖的响应时间小于1 min,进样间隔时间为3 min;对葡萄糖的电流响应范围为1．96×10~(-5)～1．80×10~(-4)mol/L,检测限为9．80×10~(-6)mol/L。传感器未使用葡萄糖氧化酶或其他生物酶,受温度的影响较小,样品中的氧对测定没有影响。在镍电极上,抗坏血酸、尿酸和多巴胺等物质不干扰血清中葡萄糖的测定。传感器用于测定血清中葡萄糖含量,相对标准偏差为4．3％。与己糖激酶法的测定结果一致。传感器制备简单,无需特殊保管,经简单处理后可重复使用。     

基于Al/Ni双氢氧化物纳米线无酶葡萄糖传感器的研究

本文采用多孔聚碳酸酯(PC)模板在加热条件下通过溶液渗透和共沉淀制得了Al/Ni双氢氧化物纳米线,并将其修饰到玻碳电极制成无酶葡萄糖传感器。考察了该传感器在不同扫描速度时的循环伏安行为,比较了裸玻碳电极、不同修饰电极对响应电流的影响。在优化条件下进行葡萄糖检测,线性范围为2.0×10-5～1.3×10-3 mol/L,检出限可以达到5.0×10-6 mol/L。该方法快捷、灵敏、分析性能好,操作简便。可将其应用于血清中葡萄糖含量的测定。     

镍纳米粒子修饰碳糊电极直接电催化鸟嘌呤的研究

将镍纳米粒子与石蜡、石墨按照一定比例混合制备镍纳米粒子修饰碳糊电极,采用循环伏安法(CV)对修饰碳糊电极进行电化学表征,在0.1 mol/L B-R缓冲溶液(pH4.5)中研究了鸟嘌呤在该修饰电极上的电化学行为。结果表明,与裸碳糊电极相比,以掺杂法制备的镍纳米粒子修饰电极能够明显降低鸟嘌呤的过电位,增大其氧化电流,很好地催化氧化鸟嘌呤。在优化的实验条件下,鸟嘌呤在该修饰电极上的氧化峰电流与其浓度在1.0×10-5~5.0×10-4mol/L范围内呈良好的线性关系,检出限(3σ)为7.5×10-6mol/L。     

碳纳米管负载铂-二氧化钌纳米颗粒用于葡萄糖传感器的研究

建立了多壁碳纳米管(MWNTs)负载铂二二氧化钌纳米颗粒的液相化学还原法.以Nafion为固定剂,将Pt-RuO2/MWNTs复合材料修饰于玻碳电极的表面,制备了一种无酶型葡萄糖传感器.实验表明:复合材料修饰的电极对葡萄糖响应电流明显,并且受抗坏血酸(AA)、多巴胺(DA)和尿酸(UA)的干扰小.本实验采用安培法测定葡萄糖,线性范围为2 0×10 3～1.0×10-2 mol/L(R～0.9965);灵敏度为119.26 μA cm-2(mmol/L)-1;检出限为1.25×10 -5 mol/L(信噪比为3);响应时间为4.8 s.PtRuO2/MWNTs修饰电极可作为性能良好的无酶型葡萄糖传感器.     

葡萄糖氧化酶在石墨烯-纳米氧化锌修饰玻碳电极上的直接电化学及对葡萄糖的生物传感

采用滴涂法和电沉积法制备了石墨烯/纳米氧化锌复合膜修饰玻碳电极,再将葡萄糖氧化酶固定在修饰电极表面制成了电化学生物传感器,用于葡萄糖的灵敏测定。用循环伏安法在-0.7～-0.1 V范围内研究了葡萄糖氧化酶在修饰电极上的直接电化学行为。结果表明,石墨烯/纳米氧化锌复合膜能很好地保持葡萄糖氧化酶的生物活性,并显著促进了其电化学过程。在0.1 mol/L磷酸盐缓冲溶液(pH 7.0)中,固定在修饰电极上的葡萄糖氧化酶呈现出一对近乎可逆的氧化还原峰,并且对葡萄糖的氧化具有良好的催化作用。葡萄糖氧化酶在修饰电极上的电子转移常数ks为1.42 s-1,修饰电极对葡萄糖催化的米氏常数Kampp为14.2μmol/L。线性范围为2.5×10-6～1.5×10-3mol/L,检出限为2.4×10-7mol/L(S/N=3)。此修饰电极具有良好的导电性能、稳定性和重现性,可用于实际样品的分析测定。     

镍纳米粒子-离子液体修饰碳糊电极的制备及其对多巴胺的测定

制备了镍纳米粒子-离子液体修饰电极,在0.1 mol/L磷酸缓冲溶液(pH 6.0)中研究了多巴胺(DA)在修饰电极上的电化学行为.与裸电极相比,DA在该修饰电极上的氧化还原电位明显降低,氧化还原反应的峰电流明显增大,DA的峰电流与其浓度在2.0×10~(-8) ～1.0×10~(-4) mol/L范围内呈良好的线性关系,检出限为6.5×10~(-9) mol/L.该修饰电极对抗坏血酸具有明显的抗干扰能力.     

碳纳米管/纳米二氧化钛-聚苯胺载铂复合电极对葡萄糖的电催化氧化

采用循环伏安(CV)、微分脉冲伏安(DPV)和计时电位法研究了碳纳米管/纳米TiO2-聚苯胺膜载Pt(CNT/nanoTiO2-PAn-Pt)复合电极对葡萄糖的电催化氧化作用。结果表明,在碱性介质中CNT/nanoTiO2-PAn-Pt复合电极对葡萄糖的电氧化具有高催化活性。当葡萄糖浓度为1.25×10-2mol/L时,氧化峰电流密度达到32.8 mA/cm2,且有很高的灵敏度和稳定性;当葡萄糖浓度为1.0×10-5mol/L时,其响应电流密度为13.8mA/cm2。大电流氧化时未发生振荡现象,是葡萄糖传感器的高活性催化电极。     

基于立方体纳米氧化亚铜修饰的安培型葡萄糖生物传感器的制备及性能研究

将合成的立方体纳米氧化亚铜用于修饰玻碳电极,在其上固定葡萄糖氧化酶,构建了高灵敏的安培型葡萄糖生物传感器.采用X射线衍射(X RD)、扫描电镜(SEM)对合成的立方体纳米氧化亚铜及其修饰电极进行了表征.结果表明,合成的纳米氧化亚铜为均匀的立方体形状.采用循环伏安法(CV)、交流阻抗谱(EIS)、差分脉冲伏安法(DPV)及计时电流法(CA)考察了修饰电极的电化学行为.在含0.1 mmol/L葡萄糖的磷酸盐缓冲溶液(pH 7.4)中研究了立方体纳米氧化亚铜修饰电极的循环伏安(CV)响应,实验结果表明,此修饰电极对葡萄糖显示出良好的电催化性能.DPV响应电流与葡萄糖的浓度在5.0×10-6 ～4.0× 10-3mol/L范围内呈良好的线性关系,线性相关系数R2=0.9983,检出限为6.8×10-7 mol/L(S/N=3).CA实验结果表明,尿酸、抗坏血酸、D-果糖对传感器不产生干扰.本传感器具有较好的重现性和稳定性,可用于实际样品中葡萄糖的检测.     

基于石墨烯修饰电极测定蔬菜中残余对硫磷的研究

制备了石墨烯薄膜修饰玻碳电极,并通过循环伏安法研究了对硫磷(PT)在该修饰电极上的电化学行为。对支持电解质、溶液pH值等实验条件进行了优化。结果表明,在0.1mol/L的乙酸-乙酸钠缓冲溶液(pH=5.0)中,PT在石墨烯薄膜修饰电极上具有良好的电化学响应,对比裸玻碳电极,PT的氧化峰峰电流显著提高,表明修饰膜对PT的电化学氧化具有一定的催化作用。PT的氧化峰电流及其浓度分别在1.0×10-7~1.0×10-6 mol/L范围内和3.0×10-6~1.0×10-5 mol/L范围内呈良好的线性关系,线性相关系数分别是0.9956和0.9874,检出限为1.0×10-8 mol/L。将该修饰电极应用于小白菜中残留PT的测量,结果比较满意。     

基于静电吸附碳纳米管和壳聚糖固定葡萄糖氧化酶的生物传感器

以Nafion-聚中性红修饰电极为基底,自组装多壁碳纳米管和壳聚糖之后,再固定上葡萄糖氧化酶,制成葡萄糖生物传感器.实验表明,本传感器在30 ℃的PBS(pH 7.0)中对葡萄糖的线性响应范围为5.0×10-6～2.0×10-3 mol/L,线性相关系数为0.9948,检出限为1.0×10-6 mol/L,达到95%稳态电流所用的时间<10 s.本修饰电极具有良好的稳定性,于4 ℃环境保存30 d后峰电流值约为原来的84.3%,且具有较低的工作电位,能有效地消除抗坏血酸等的干扰.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.