Nanoporosity-driven superhydrophilicity: a means to create multifunctional antifogging coatings

Multifunctional nanoporous thin films have been fabricated from layer-by-layer assembled silica nanoparticles and a polycation. The resultant multilayer films were found to exhibit both antifogging and antireflection properties. The antifogging properties are a direct result of the development of superhydrophilic wetting characteristics (water droplet contact angle <5 degrees within 0.5 s or less). The nearly instantaneous sheetlike wetting promoted by the superhydrophilic multilayer prevents light scattering water droplets from forming on a surface. The low refractive index of the multilayer film (as low as 1.22) resulting from the presence of nanopores was found to impart excellent antireflection properties. Glass slides coated on both sides with a nanoporous multilayer film exhibited transmission levels as high as 99.8%. Stable superhydrophilic wetting characteristics were obtained only after a critical number of bilayers were deposited onto a surface. The assembly conditions (solution pH and nanoparticle concentration), as well as the choice of nanoparticle size, were found to strongly influence film properties. It is suggested that the superhydrophilic behavior is driven by the rapid infiltration of water into a 3D nanoporous network created under specific assembly conditions.     

Direct catalytic route to superhydrophobic polyethylene films

Polyethylene films grow on a flat silica surface modified by the bis(imino)pyridyl iron(II) catalyst during ethylene polymerization in toluene solvent. The resulting films show superhydrophobic properties. Advancing water contact angle as high as 169 degrees and sliding angles as low as 2 degrees are obtained on these films. SEM images reveal special surface structures of these films containing micrometer-sized islands, submicrometer particles on the islands, and stress nanofibers between the islands, which render superhydrophobicity to the polyethylene surfaces. After the submicrometer particles and stress nanofibers are removed by annealing, the superhydrophobic properties of the polymer films disappear.     

Highly transparent superhydrophobic thin film with low refractive index prepared by one-step coating of modified silica nanoparticles

An easy and effective method to prepare superhydrophobic thin film has been developed. The film with optically transparent and low refractive index was composed by one-step coating with modified silica nanoparticles. The silica nanoparticles were prepared by sol–gel process of hydrolysis and condensation of alkoxysilane compounds and then surface modification silica nanoparticles, 50 ± 10 nm, were accomplished using methoxytrimethylsilane (MOTMS). Water contact angle of film increased with the weight of MOTMS of silica sol. When the weight of MOTMS was optimized, the water contact angle and sliding angle of film were 152.8° and less than 10°, respectively. The transmittance of film was also increased as compared to the un-coated microscope glass slide, from 91 to 93.5 %. The refractive index of the film was approximately 1.09 as measured by ellipsometer. The superhydrphobic thin film was also successfully made by using spray coating and the water contact angle of this film was more than 160°. Surface morphology of difference coating methods, dip and spray, were studied. Our result suggests that the film can be applied for superhydrophobicity and optical applications.     

Combining layer-by-layer assembly with electrodeposition of silver aggregates for fabricating superhydrophobic surfaces

Taking advantage of the stability and penetrability of layer-by-layer (LbL) films, we develop a novel method to fabricate a branchlike structure of Ag aggregates on the matrix of a LbL polyelectrolyte multilayer by an electrodeposition technique. The morphology of Ag aggregates can be adjusted by electrodeposition time and potential. Moreover, after further chemisorption of a self-assembled monolayer of n-dodecanethiol, the as-prepared surface becomes superhydrophobic with a contact angle as high as 154 degrees and a tilt angle lower than 3 degrees.     

Flexible Broadband Light Absorbers with a Superhydrophobic Surface Fabricated by Ultraviolet-assisted Nanoimprint Lithography

We present a simple approach to fabricate a kind of composite films with a superhydrophobic and broadband light absorbing surface by ultraviolet-assisted nanoimprinting over a gradiently deposited composite matrix. The wettability and optical property of the resultant surfaces are tunable by the deposition time before polymerization(T_s) and mold's topography. Mechanically robust and elastomeric films exhibiting high sunlight absorptivity up to 98.13% and contact angle of their surfaces up to 150° are prepared under optimized conditions, as using a mold with a small pattern size(hexagonal periodic mold with cylinder diameter of ca. 37 μm) under T_s=10 min for imprinting the crosslinked poly[di(ethylene glycol) ethyl ether acrylate] and poly(isobornyl acrylate) in the presence of polypyrrole(PPy) nanoparticles. Such dual functions are found related to the hierarchical architecture of the surface, arising from the synergetic effects of the periodical patterned polymer substrate and spontaneously assembled PPy microstructures on the patterns. The current strategy based on the combination of ultraviolet-assisted nanoimprint lithography and hierarchical assembly of gradiently deposited black nano-fillers offers a new insight into the design of robust superhydrophobic and black surfaces, which is helpful to deepen our understanding of the relationship between liquid/light manipulation and micro/nanostructured surfaces.     

Electrochemical growth of two-dimensional gold nanostructures on a thin polypyrrole film modified ITO electrode

Two-dimensional gold nanostructures have been fabricated by electrochemical deposition of gold nanoparticles onto indium tin oxide (ITO) glass substrate modified with thin polypyrrole film. By controlling the electrodeposition conditions, gold nanoparticles with dendritic rod, sheet, flower-like (consisting of staggered nanosheets), and pinecone-like structures were generated. The flower-like gold nanoparticles showed high catalytic activity on electrochemical reduction of oxygen, and its activity was measured to be approximately 25 times that of gold pinecones and 10(4) times that of gold nanosheets in terms of gold weight. The pinecone-like nanoparticles can form a compact film with nano-/microscale binary structure like a lotus leaf surface. After modification with n-dodecanethiol, the surface showed superhydrophobic properties with a water contact angle of 153.4 degrees and a tilt angle of 4.4 degrees (5 microL droplet).     

Superhydrophobic polyimide films with a hierarchical topography: combined replica molding and layer-by-layer assembly

Artificial superhydrophobic surfaces with a hierarchical topography were fabricated by using layer-by-layer assembly of polyelectrolytes and silica nanoparticles on microsphere-patterned polyimide precursor substrates followed with thermal and fluoroalkylsilane treatment. In this special hierarchical topography, micrometer-scale structures were provided by replica molding of polyamic acid using two-dimensional arrays of polystyrene latex spheres as templates, and nanosized silica particles were then assembled on these microspheres to construct finer structures at the nanoscale. Heat treatment was conducted to induce chemical cross-linking between polyelectrolytes and simultaneously convert polyamic acid to polyimide. After surface modification with fluoroalkylsilane, the as-prepared highly hydrophilic surface was endowed with superhydrophobicity due to the bioinspired combination of low surface energy materials and hierarchical surface structures. A superhydrophobic surface with a static water contact angle of 160 degrees and sliding angle of less than 10 degrees was obtained. Notably, the polyimide microspheres were integrated with the substrate and were mechanically stable. In addition, the chemical and mechanical stability of the polyelectrolyte/silica nanoparticle multilayers could be increased by heat-induced cross-linking between polyelectrolytes to form nylon-like films, as well as the formation of interfacial chemical bonds.     

Fabrication of superhydrophobic polymer films with hierarchical silver microbowl array structures

Flexible superhydrophobic polyvinyl alcohol (PVA) films with silver bowl-like array structure are fabricated based on the thermal evaporation with sphere monolayer as templates and the modification of 1H, 1H, 2H, 2H-perfluorodecanethiol on silver surface. The silver microbowl arrays were composed of silver nanoparticles with an average diameter size of ca. 10 nm. The polymer films exhibit excellent stability and remarkable superhydrophobicity with a high water contact angle (CA) of about 163° and a low sliding angle (SA) of less than 3°.     

Layer-by-layer fabrication of broad-band superhydrophobic antireflection coatings in near-infrared region

Broad-band superhydrophobic antireflective (AR) coatings in near infrared (NIR) region were readily fabricated on silicon or quartz substrates by a layer-by-layer (LbL) assembly technique. First, a porous poly(diallyldimethylammonium chloride) (PDDA)/SiO2 nanoparticle multilayer coating with AR property was prepared by LbL deposition of PDDA and 200 nm SiO2 nanoparticles. PDDA was then alternately assembled with sodium silicate on the PDDA/SiO2 nanoparticle coating to prepare a two-level hierarchical surface. Superhydrophobic AR coating with a water contact angle of 154 degrees was finally obtained after chemical vapor deposition of a layer of fluoroalkylsilane on the hierarchical surface. Quartz substrate with the as-fabricated superhydrophobic AR coating has a maximal transmittance above 98% of incidence light in the NIR region, which is increased by five percent compared with bare quartz substrate. Simultaneously, the superhydrophobic property endows the AR coating with water-repellent ability. Such superhydrophobic AR coatings can effectively avoid the disturbance of water vapor on their AR property and are expected to be applicable under humid environments.     

Polymer-Based Superhydrophobic Coating Fabricated from Polyelectrolyte Multilayers of Poly(allylamine hydrochloride) and Poly(acrylic acid)

Superhydrophobic films mainly based on poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) polyelectrolyte multilayer have been deposited onto cleaned glass substrate by a layer-by-layer dip coating method. 3 bilayers of the PAH and PAA was directly coated onto the substrate as an underlying layer for subsequent coating. Desired surface roughness on the polyelectrolyte bilayers was created by etching the bilayers in hydrochloric acid solution so as to create the open pore having suitable size at the surface. Then, nanoparticles such as SiO₂ and TiO₂ of various sizes were deposited onto the etched polyelectrolyte bilayers. Finally, the surfaces were further modified with semifluorinated silane followed by cross-linking at 180 °C for 2 h to obtain desirable surface morphological features. The effect of etching time and addition of nanoparticles on surface morphology was investigated using an atomic force microscope (AFM). Wetting ability of the prepared film was determined by measuring water droplet contact angle using a goniometer. Adhesion between the superhydrophobic films and the substrate was evaluated by using a standard tape test method (D3359). The adhesion was improved by reducing the organic content in the films.     

Layer-by-layer-assembled multilayer films of polyelectrolyte-stabilized surfactant micelles for the incorporation of noncharged organic dyes

Noncharged pyrene molecules were incorporated into multilayer films by first loading pyrene into poly(acrylic acid) (PAA)-stabilized cetyltrimethylammonium bromide (CTAB) micelles (noted as PAA&(Py@CTAB)) and then layer-by-layer (LbL) assembled with poly(diallyldimethylammonium chloride) (PDDA). The stable incorporation of pyrene into multilayer films was confirmed by quartz crystal microbalance (QCM) measurements and UV-vis absorption spectroscopy. The resultant PAA&(Py@CTAB)/PDDA multilayer films show an exponential growth behavior because of the increased surface roughness with increasing number of film deposition cycles. The present study will open a general and cost-effective avenue for the incorporation of noncharged species, such as organic molecules, nanoparticles, and so forth, into LbL-assembled multilayer films by using polyelectrolyte-stabilized surfactant micelles as carriers.     

Novel colorimetric sensor for mercury (Ⅱ) based on layer-by-layer assembly of unmodified silver triangular nanoplates

A simple layer-by-layer deposition technique was used to fabricate the multilayer thin films of unmodified silver triangular nanoplates(AgTNPs).The multilayer of AgTNPs thin films were fabricated by alternate deposition of each anionic sodium citrate stabilized AgTNPs and cationic poly(diallyldimethylammonium chloride).All prepared AgTNPs multilayer thin films were exhibited a strong plasmon band at the wavelength of 667 nm,which confirmed the formation of AgTNPs onto the substrate.The characteristics of the multilayer thin films were investigated using contact angle measurement,UV-visible spectroscopy,X-ray diffraction analysis(XRD),atomic force microscope(AFM)and field emission scanning electron microscope(FESEM).As these films are to be used as a mercury(II)colorimetric sensor,the changes in optical properties of the films were evaluated for various mercury(Ⅱ)concentrations.AgTNPs assembled into thin films showed a strong color shift from blue to mauve and colorless when exposed to mercury(Ⅱ).The constructed multilayer thin films exhibited excellent color changes of mercury(II) with a linear range between 0.5 and 20 ppm.The limit of detection(LOD) and limit of quantitation(LOQ) were 0.45 ± 0.002 and 1.52 ± 0.002 ppm,respectively.The recovery values of AgTNPs multilayer thin films are satisfactory in the range of 100.1%-106.4%when applied to determining mercury(Ⅱ) in water samples.     

Silver nanocomposite layer-by-layer films based on assembled polyelectrolyte/dendrimer

Silver nanocomposite multilayer films were prepared through the in situ method. Multilayer thin films, prepared through the sequential electrostatic deposition of a positively charged third-generation poly(amidoamine) dendrimer (PAMAM) and negatively charged poly(styrenesulfonate) (PSS) and poly(acrylic acid) (PAA), were utilized as nanoreactors for the formation of silver nanoparticles. The silver ions were preorganized in layer-by-layer (LBL) films composed of PAMAM dendrimers and subsequently reduced with hydrogen to prepare the silver nanoparticles. The UV-vis spectrum and profilometer were used to characterize the regular growth of bilayers. UV-vis absorption from plasmon resonance at 435 nm and TEM images indicated the formation of the silver nanoparticles in the multilayer films. The silver nanocomposite LBL films were also constructed on the indium tin oxide-glass and investigated using cyclic voltammetry. The silver nanoparticles in the multilayer films have a stronger negative redox potential. The silver nanocomposite LBL films may have a potential application in the catalysis of reduction of 4-nitrophenol with sodium borohydride.     

Production and characterization of stable superhydrophobic surfaces based on copper hydroxide nanoneedles mimicking the legs of water striders

The present work reports a simple and economic route for production and characterization of stable superhydrophobic surfaces from thin copper layers coated on arbitrary solid substrates. The thin copper layer was anodized in a 2 M aqueous solution of potassium hydroxide to form a thin film of copper hydroxide nanoneedles; then the film was reacted with n-dodecanethiol to form a thermally stable Cu(SC12H25)2 superhydrophobic coating. The contact angle of the modified nanoneedle surface was higher than 150 degrees , and its tilt angle was smaller than 2 degrees . Furthermore, the surface fabricated on copper foil kept its superhydrophobic property after heating at 160 degrees C in air for over 42 h. This technique has also been applied for fabrication of copper wire with superhydrophobic submicrofiber coating to mimic water strider legs. The maximal supporting force of the superhydrophobic copper column has also been investigated in comparison to real water striders.     

Self-repairing and superhydrophobic film of gold nanoparticles and fullerene pyridyl derivative based on the self-assembly approach

In this paper, we report that thin gold films can be prepared on the water/toluene interface by self-assembly of gold nanoparticles (NPs) and fullerene pyridyl derivatives. The assembled films were characterized using UV–vis spectroscopy and transmission electron microscope (TEM). The films show self-repairing and superhydrophobic properties.     

Engineering of superhydrophobic silica microparticles and thin coatings on polymeric films by ultrasound irradiation

Superhydrophobic coatings are one of the recent hot topics in industrial applications as well as academic studies. The mimicking lotus leaves' superhydrophobic properties have been successfully transferred to real-life applications. However, the current preparation methods used to obtain superhydrophobic coatings are still complex, commonly are not transparent and/or not durable.In the present study, a new relatively simple way to prepare superhydrophobic coatings on polymeric films is described. First, superhydrophobic silica microparticles (MPs) were synthesized by fluorination of SiO₂ MPs produced by a modified Stöber method. Briefly, tetraethyl orthosilicate was polymerized in an ethanol/water continuous phase under basic conditions, and the resultant SiO₂ MPs were dispersed in heptane as a continuous phase and reacted with 1H,1H,2H,2H-perfluorododecyltrichlorosilane (FTS) to yield FTS-SiO₂ MPs, which were dried and dispersed in decane. Superhydrophobic thin coatings were then produced by a ‘throwing stones’ sonication technique and deposited onto polycarbonate, polypropylene, polyethylene, and polyurethane films. The coatings are durable, may be transparent, and exhibit self-cleaning properties for the specific practical applications. The MPs and coated polymeric films were characterized by dynamic light scattering, high-resolution scanning electron microscopy, water contact and sliding angle measurements, and infrared and x-ray photoelectron spectroscopy. This ultrasound-assisted coating process may be upscaled and applied to many polymeric films, for instance polymethyl methacrylate, polystyrene, and polyvinyl chloride. Various applications are envisaged, including but not limited to self-cleaning windows, anti-sticking of snow to antennas and windows, solar panels, roof tiles, agricultural applications, corrosion resistance, and anti-biofouling.     

Fabrication of CdS films with superhydrophobicity by the microwave assisted chemical bath deposition

A simple method of microwave assisted chemical bath deposition (MA-CBD) was adopted to fabricate cadmium sulfide (CdS) thin films. The superhydrophobic surface with a water contact angle (CA) of 151 degrees was obtained. Via a scanning electron microscopy (SEM) observation, the film was proved having a porous micro/nano-binary structure which can change the property of the surface and highly enhance the hydrophobicity of the film. A possible mechanism was suggested to describe the growth of the porous structure, in which the microwave heating takes an important role in the formation of two distinct characteristic dimensions of CdS precipitates, the growth of CdS sheets in micro-scale and sphere particles in nano-scale. The superhydrophobic films may provide novel platforms for photovoltaic, sensor, microfluidic and other device applications.     

Superhydrophobic composite films produced on various substrates

Hydrophilic silica (SiO2) nanoparticles were dispersed in solutions of poly(methyl methacrylate) (PMMA) and in solutions of a commercial poly(alkyl siloxane) (Rhodorsil 224), and the suspensions were sprayed on glass surfaces. The effect of the particle concentration on the hydrophobic character of PMMA-SiO2 and Rhodorsil-SiO2 films was investigated and showed the following: (i) Static contact angles (theta s), measured on surfaces that were prepared from dilute dispersions (particle concentration <1% w/v), increase rapidly with particle concentration and reach maximum values (154 and 164 degrees for PMMA-SiO2 and siloxane-SiO2, respectively). Further increases in particle concentration do not have any effect on theta s. (ii) The effect of particle concentration on the contact angle hysteresis (thetaAlpha - thetaR) is more complicated: as the particle concentration increases, we first notice an increase in hysteresis, which then decreases and finally becomes constant at elevated particle concentrations. The lowest thetaAlpha - thetaR values were 5 degrees for PMMA-SiO2 and 3 degrees for siloxane-SiO2, respectively. (iii) SEM and AFM images show that a two-length-scale hierarchical structure is formed on the surface of the superhydrophobic films. It is demonstrated that superhydrophobicity can be achieved using various hydrophilic nanoparticles (alumina and tin oxide nanoparticles were successfully tested) and that the substrate has almost no effect on the hydrophobic character of the applied coatings, which were produced on silicon, concrete, aluminum, silk, wood, marble, and of course glass. The results are discussed in light of Wenzel and Cassie-Baxter models.     

聚合物层状组装膜

介绍了近几年来我们研究组在层状组装膜的构筑以及功能化研究方面取得的一些最新进展.包括结合表面溶胶-凝胶技术与静电层状组装技术,实现了二阶非线性基团在层状组装多层膜中的非对称排列,制备了具有二阶非线性效应的膜材料;采用室温压印技术,发展了一种简便、经济和具有普适性的层状组装聚合物膜图案化方法;以轻度交联的聚合物微凝胶为构筑基元,制备了具有高负载量的聚合物层状组装膜;发展了一种基于离子剥离技术的层状组装自支持膜制备方法;基于层状组装技术,制备了具有超疏水和抗反射功能的涂层.     

Extremely superhydrophobic surfaces with micro- and nanostructures fabricated by copper catalytic etching

We demonstrate a simple method for the fabrication of rough silicon surfaces with micro- and nanostructures, which exhibited superhydrophobic behaviors. Hierarchically rough silicon surfaces were prepared by copper (Cu)-assisted chemical etching process where Cu nanoparticles having particle size of 10-30 nm were deposited on silicon surface, depending on the period of time of electroless Cu plating. Surface roughness was controlled by both the size of Cu nanoparticles and etching conditions. As-synthesized rough silicon surfaces showed water contact angles ranging from 93° to 149°. Moreover, the hierarchically rough silicon surfaces were chemically modified by spin-coating of a thin layer of Teflon precursor with low surface energy. And thus it exhibited nonsticky and enhanced hydrophobic properties with extremely high contact angle of nearly 180°.