关于-RTlnK_c~■=Δ_rG_m~■(c~■)的讨论

在等温等压条件下,通过pB=cBRT关系转换,所得关系式证明了-RTlnK—cΟ=ΔrG—mΟ(c—Ο)。还分析推证出ΔrG—mΟ(c—Ο)和ΔrG—mΟ(p—Ο)、ΔrH—Οm(c—Ο)和ΔrHΟ—m(p—Ο)、ΔrSΟ—m(c—Ο)和ΔrSΟ—m(p—Ο)、ΔrUΟ—m(c—Ο)和ΔrHΟ—m(cΟ—)以及ΔrG—Οm(c—Ο)和ΔrA—mΟ(c—Ο)之间的几个关系式,进一步证实了-RTlnK—cΟ=ΔrGΟ—m(c—Ο)。     

尾式亮氨酸四苯基卟啉锌与嘧啶轴配反应光谱和热力学

研究了 5 - (4′ -亮氨酸丁氧苯基 ) - 10 ,15 ,2 0 -三苯基卟啉锌 (Zn[Leu -TPP])与嘧啶 (L)在氯仿溶液中轴配反应光谱和热力学性质 .用紫外 -可见分光光度法确定了轴向配位反应体系的配位数 (n)和平衡常数K .用温度系数法求得了轴配反应的标准摩尔焓变ΔrH m 和标准摩尔熵变ΔrS m .探讨了温度对轴向配位反应反应的影响 .     

碳酸二甲酯与苯酚酯交换合成碳酸二苯酯的热力学性质及均相催化剂

在298.15K,101.325kPa条件下,液态碳酸二甲酯(DMC)的标准Gibbs自由能和熵分别估算为-472.3kJ*mol-1和245.2J*mol-1*K-1.在298K～523K计算了由DMC和苯酚生成碳酸二苯酯(DPC)和苯甲醚反应的热力学性质(ΔrH0m,ΔrS0m,ΔrG0m和平衡常数).计算出的热力学性质表明,DMC和苯酚酯交换合成DPC反应是吸热的,并且在热力学上是不利的.研究了n-Bu2SnO, Ti(OC4H9)4, AlCl3和ZnCl2四种酯交换法合成DPC反应的催化剂,其中n-Bu2SnO具有最高的催化活性.热力学计算和实验结果均表明,合成DPC反应的最佳温度为453K.当以n-Bu2SnO为催化剂,n(苯酚)∶n(DMC)＝4∶1时,DPC的产率和选择性分别为43.0%和88.7%.     

电化学方法测定纳米材料的热力学函数

以纳米铜为例,首次采用电化学方法获取纳米材料的热力学函数.通过电化学沉积法制备了粒子尺寸约80nm的纳米铜电极,测定纳米铜与块体铜电极的电势差,以块体铜的热力学函数值为参考标准,根据纳米铜与块体铜的热力学关系式,求得纳米铜的标准摩尔生成焓、标准摩尔生成吉布斯自由能、标准摩尔熵分别为5.16kJmol-1、0.216kJmol-1、49.75JK-1mol-1,同时,求得纳米铜可逆电池反应的热效应为-4.95kJmol-1.     

邻苯二甲酸氢铵NH4(C8H5O4)(s)的低温热容和热化学研究

选择分析纯邻苯二甲酸和浓氨水为反应物,合成了邻苯二甲酸氢铵.利用元素分析、FTIR和X-射线粉末衍射技术表征了它的组成和结构.用精密自动绝热热量计测定了它在78～400 K温区的摩尔热容,将该温区的摩尔热容实验值用最小二乘法拟合,得到摩尔热容(Cp,m)随折合温度(X)变化的多项式方程,利用此方程计算出该温区内每隔5 K的舒平热容值和相对于298.15K的各种热力学函数值.另外,依据Hess定律,通过设计合理的热化学循环,利用等温环境溶解-反应热量计分别测定所设计反应的反应物和产物在所选溶剂中的溶解焓,得到该反应的反应焓为△rHθm=(1.787±0.514)kJ·mol-1.最后,利用此反应焓和反应中其他物质的热力学数据计算出邻苯二甲酸氢铵的标准摩尔生成焓为:△fHθm[NH4(C8H5O4),s]=-(912.953±0.628)kJ·mol-1.     

水合烟酸钡的合成、结构表征和热化学性质

选择烟酸和氢氧化钡作为反应物,利用室温固相合成方法,借助于球磨技术,合成了一种新的化合物-水合烟酸钡.利用化学分析、元素分析、FTIR和X射线粉末衍射等方法确定了它的组成和结构为Ba(Nic)2·3H2O(s).利用精密自动绝热热量计直接测定了此化合物在78-400 K温区的摩尔热容.在热容曲线上出现了一个明显的吸热峰,通过对热容曲线的解析,得到了相变过程的峰温、相变焓和相变熵分别为(327.097±1.082)K、(16.793±0.084)kJ·mol-1和(51.340±0.164)J·K-1·mol-1将该温区的摩尔热容实验值用最小二乘法拟合得到摩尔热容(Cp,m)对温度(T)的多项式方程,并且在此基础上计算出了它的舒平热容值和各种热力学函数值.另外,依据Hess定律,通过设计合理的热化学循环,选择体积为100mL、浓度为0.5mol·L-1的盐酸作为量热溶剂,利用等温环境溶解-反应热量计分别测量固相反应的反应物和产物在所选溶剂中的溶解焓,利用溶解焓确定固相反应的反应焓为△rH0m=-(84.12±0.38)kJ·mol-1.最后,利用固相反应的反应焓和其它反应物和产物已知的热力学数据计算出水合烟酸钡的标准摩尔生成焓为△rH0m[Ba(Nic)2·3H2O(s)]=-(2115.13±1.90)kJ·mol-1.     

粒度对纳米氧化镁吸附苯的热力学性质影响

以纳米氧化镁与水溶液中的苯作为吸附体系,研究了纳米氧化镁的粒度对吸附热力学性质的影响。实验结果表明,纳米氧化镁的粒度对吸附标准平衡常数、标准摩尔吸附吉布斯自由能变、标准摩尔吸附焓变和标准摩尔吸附熵变均有较大影响;并且随着纳米氧化镁粒度的减小,吸附标准平衡常数增大,标准摩尔吸附吉布斯自由能变、标准摩尔吸附焓变和标准摩尔吸附熵变均降低。     

立方体纳米Cu2O吸附热力学及动力学的粒度效应研究

采用不同粒径的单一(100)晶面的立方体纳米Cu₂O作为模型材料, 研究了粒径和温度对其吸附动力学和吸附热力学性质的影响规律. 基于已建立的纳米材料吸附热力学和动力学理论, 推导出了单一(100)晶面立方体纳米Cu₂O材料的吸附热力学和吸附动力学性质与粒径之间的关系式. 实验结果与理论预测结果一致: 随着纳米Cu₂O粒径的减小, 吸附速率常数增大而吸附活化能和吸附指前因子减小; 标准摩尔吸附Gibbs自由能 Δ_a $G^{\rlap{-}0}_{m}$减小而标准吸附平衡常数ln $K^{\rlap{-}0}$、 标准摩尔吸附焓 Δ_a $H^{\rlap{-}0}_{m}$和标准摩尔吸附熵 Δ_a$S^{\rlap{-}0}_{m}$均增大, 且以上参数均与粒度的倒数具有较好的线性关系.     

还原半反应的相关热力学计算

借助于经典热力学和电化学知识的结合,较系统探讨了水溶液中热力学"0"标准的选取、离子的热力学数据与单质或化合物的热力学数据能否互相借用和还原半反应热力学计算公式等问题,并计算了不同类型电极对应还原半反应电子的标准摩尔熵。研究表明:298.15K,100kPa下,还原半反应中电子的ΔfHm(e-,aq,∞)=0、ΔfGm(e-,aq,∞)=0和Sm(e-,aq,∞)=65.32J.mol-1.K-1;离子的热力学数据与单质或化合物的热力学数据可互相借用;还原半反应热力学计算公式包括:ΔhGm=-ZFE、ΔhHm=∑iνi.ΔfHm,i、ΔhGm=∑iνi.ΔfGm,i、ΔhSm=∑iνi.Sm,i、ΔhGm=ΔhHm-TΔhSm。     

尺寸效应对氧化锌微/纳体系热力学性质的影响

采用微乳液水热辅助法合成了三种不同尺寸的手榴弹状ZnO 微/纳结构. 通过设计热化学循环, 建立了纳米ZnO与块体ZnO体系热力学性质之间的关系. 并结合微量热技术对不同尺寸ZnO微/纳体系的热力学性质进行了计算. 结果表明, 尺寸效应对微/纳体系热力学性质有显著的影响: 随着反应物尺度的减小, 体系的标准摩尔反应焓、标准摩尔反应Gibbs 自由能、标准摩尔反应熵均降低, 而材料自身的标准摩尔生成焓、标准摩尔生成Gibbs 自由能、标准摩尔熵均增加.     

Preparation of Nano‐bismuth with Different Particle Sizes and the Size Dependent Electrochemical Thermodynamics

Nano‐bismuth has excellent electrochemical properties. However, it is still unclear how the particle size of nano‐bismuth influences its electrochemical thermodynamic properties. In this paper, spherical bismuth nanoparticles with different particle sizes were prepared by solvothermal method; the electrode potentials, the temperature coefficients of the electrode potentials and the thermodynamic functions of reaction for nano‐bismuth electrodes with different particle sizes at different temperatures were determined; and the effects of particle size on the electrode potential, the temperature coefficient and the thermodynamic functions were discussed. The experimental results show that particle size of bismuth nanoparticles has a significant influences on the electrochemical thermodynamic properties. The standard electrode potential of the nano‐bismuth electrode with a diameter of 39.9 nm was 0.009 V lower than that of the ordinary standard electrode (0.308 V); the temperature coefficient of the electrode potential with a diameter of 39.9 nm was nearly double that of 85.9 nm. With the particle sizes decrease, the standard molar Gibbs energy of reaction, the standard molar enthalpy of reaction, the standard molar entropy of reaction, the molar reversible reaction heat and the temperature coefficient increase; and these quantities are linearly related to the reciprocal of the particle diameter.     

Thermodynamics of nanoadsorption from solution: Theoretical and experimental research

In this study, the effect of nanoparticle size on adsorption thermodynamics was investigated. The results of theoretical and experimental studies show that particle size significantly affects the equilibrium constant and thermodynamic properties of nanoadsorption. Relationships between the equilibrium constant, thermodynamic properties and particle size were derived using the thermodynamic theory of nanoadsorption. The equilibrium constant and thermodynamic properties were obtained by investigating the adsorption of Cu²⁺ onto different sizes of nano-ZnO and the adsorption of Ag⁺ onto different sizes of nano-TiO₂. Good agreement was achieved between results obtained by experiments and predicted by theoretical analyses. The equilibrium constant and the molar Gibbs free energy of nanoadsorption were found to increase with smaller nanoparticle size. However, the effects of particle size on the molar enthalpy and the molar entropy are uncertain. In addition, the molar Gibbs free energy, the molar enthalpy, the molar entropy and the logarithm of the equilibrium constant are linearly related to the reciprocal of the diameter of the nanoparticle. The thermodynamic properties revealed in this study may provide important guidelines for research and application in the field of nanoadsorption.     

Size effect on thermodynamic properties of CaMoO4 micro/nano materials and reaction systems

CaMoO₄ micro/nano hollow spheres with three different sizes were prepared via a reverse-microemulsion route at room temperature. Through designing a novel thermochemical cycle, the relationship between thermodynamic properties of nano CaMoO₄ and bulk CaMoO₄ was built. Combined with in situ microcalorimetry, change regularities for the thermodynamic properties of the prepared CaMoO₄ micro/nano materials and reaction systems were obtained. The results reveal that size effect has significant influence on thermodynamic properties of micro/nano materials and reaction systems. Along with the size decreasing, the standard molar enthalpy, standard molar Gibbs free energy and standard molar entropy of reaction of micro/nano reaction systems decreased, but the standard molar enthalpy of formation, standard molar Gibbs free energy of formation and standard molar entropy of micro/nano materials increased.     

Thermodynamic properties and equilibrium constant of chemical reaction in nanosystem: An theoretical and experimental study

The theoretical relations of thermodynamic properties, the equilibrium constant and reactant size in nanosystem are described. The effects of size on thermodynamic properties and the equilibrium constant were studied using nanosize zinc oxide and sodium bisulfate solution as a reaction system. The experimental results indicated that the molar Gibbs free energy, the molar enthalpy and the molar entropy of the reaction decrease, but the equilibrium constant increases with decreasing reactant size. Linear trends were observed between the reciprocal of size for nano-reactant and thermodynamic variable, which are consistent with the theoretical relations.     

立方体纳米Cu2O表面热力学函数的粒度及温度效应

液相还原法合成了4种粒度在40-120 nm的立方体纳米氧化亚铜（Cu₂O）。利用X射线衍射仪（XRD）、显微拉曼光谱仪和场发射扫描电子显微镜（FE-SEM）对纳米Cu₂O的物相组成及形貌结构进行了表征。采用原位微热量技术实时获取纳米/块体Cu₂O与HNO₃反应过程的热动力学信息,结合热化学循环及动力学过渡态理论计算得到纳米Cu₂O的表面热力学函数。在薛永强等建立的无内孔球形纳米颗粒的热力学模型基础上,发展了立方体纳米颗粒的热力学模型。最后由理论结合实验结果分析了粒度和温度对表面热力学函数的影响规律及原因。结果表明,摩尔表面Gibbs自由能、摩尔表面焓和摩尔表面熵均随粒度减小而增大,且与粒度的倒数呈线性关系,这与立方体热力学模型规律一致;随着温度的升高,摩尔表面焓和摩尔表面熵均增大,摩尔表面Gibbs自由能则减小。本文不仅丰富和发展了纳米热力学基本理论,还为纳米材料表面热力学研究及应用提供了方法和思路。     

立方体纳米氧化亚铜反应动力学的理论及实验研究

为了探究纳米多相反应过程的动力学行为,本文通过液相还原法可控合成了粒度为55 nm的立方体氧化亚铜（Cu₂O）。基于纳米与块体Cu₂O的区别,采用原位微量热技术获取Cu₂O体系与HNO₃反应过程的热动力学精细信息,结合热动力学原理及动力学过渡态理论计算得到Cu₂O反应动力学参数,并建立立方体动力学模型讨论并佐证动力学实验结果。结果表明,纳米Cu₂O的反应速率常数大于块体,而表观活化能、指前因子、活化焓、活化熵和活化Gibbs自由能均小于块体;随着温度的升高,纳米Cu₂O的反应速率常数和活化Gibbs自由能均增大。动力学模型表明影响反应动力学参数的主要因素为：偏摩尔表面焓影响表观活化能,偏摩尔表面熵影响指前因子,偏摩尔表面Gibbs自由能影响反应速率常数。本文为纳米材料多相反应动力学参数的获取和分析应用提供了一种普适的理论模型和实验方法。     

异丁烷脱氢制异丁烯体系的热力学分析

对等温反应条件下的异丁烷脱氢制异丁烯反应进行了热力学分析,以获得等温反应条件下,压力和温度或其他反应条件与异丁烷脱氢反应的自由能ΔrG与热焓值ΔrH之间的关系。考察了不同反应条件(压力、温度和进料方式等)对于异丁烷脱氢反应的转化率的影响,为今后异丁烷脱氢制异丁烯工艺的开发提供热力学基础数据的支持。