Preconcentration technique for manganese by adsorption onto a tantalum wire for tungsten tube atomizer electrothermal atomization atomic absorption spectrometry

A multi-pumping flow system for the spectrophotometric determination of nitrite and nitrate is described. The determination of nitrite is based on the Griess-Ilosvay reaction. Nitrate can be determined after its on-line reduction to nitrite using hydrazine sulphate in alkaline medium. Calibration was linear up to 3 mg NO₂ ⁻ L⁻¹ with a limit of detection (3s_b/S) of 0.013 mg NO₂ ⁻ L⁻¹ an injection throughput of 55 injections h⁻¹ and a repeatability (RSD) of 0.5% for the direct determination of nitrite. Two calibration graphs within the ranges 0.039–7 mg NO₃ ⁻ L⁻¹ and 0.026–5 mg NO₂ ⁻ L⁻¹ were run for the determination of nitrate and nitrite under reducing conditions, respectively. A limit of detection of 0.039 mg NO₃ ⁻ L⁻¹ was obtained. An injection throughput of 27 injections h⁻¹ and an RSD lower than 1.5% were achieved. The method was successfully applied to the determination of nitrite and nitrate in water samples. Correspondence: Víctor Cerdà, Department of Chemistry, University of the Balearic Islands, Carretera de Valldemossa Km7.5, 07122 Palma de Mallorca, Spain     

Kinetic-potentiometric assay of formaldehyde in pharmaceutical and industrial samples, monitored by copper solid ion selective electrode, after its reaction with the copper(II)-bis-(ethylenediamine) complex

A kinetic-potentiometric method is described for the quantitative assay of formaldehyde (HCHO) in pharmaceutical and industrial preparations. It is based on the reaction of HCHO with (ethylenediamine)-Cu(II)-sulfate [Cu(CH₂NH₂)₂(H₂O)₂] · SO₄. The changes in potential, resulting from the release of the Cu(II) cations, are monitored with a Cu(II)-ion selective electrode. The calibration curve for the HCHO is linear in the concentration range 50–250 mg L⁻¹, with a limit of detection of 8.5 mg L⁻¹. The method shows very good reproducibility with an RSD of 2.6% for successive injections (n = 5) of 150 mg L⁻¹ HCHO primary solution, while it is interference free. The method was successfully tested in various industrial and pharmaceutical preparations.     

Ammonium pyrrolidinedithiocarbamate-modified activated carbon micro-column extraction for the determination of As(III) in water by graphite furnace atomic absorption spectrometry

A simple and selective method using ammonium pyrrolidinedithiocarbamate modified activated carbon (APDC-AC) as solid phase extractant has been developed for speciation of As(III) in water samples. At pH 1.8–3.0, As(III) could be adsorbed quantitatively by APDC-AC, and then eluted completely with 2.0 mL of 0.1 mol L⁻¹ HNO₃, while As(V) could almost not be retained at pH 1–7. Effects of acidity, sample flow rate, concentration of elution solution and interfering ions on the recovery of As(III) have been systematically investigated. Under the optimal conditions, the adsorption capacity of APDC-AC for As(III) is 7.3 mg g⁻¹. The detection limit (3σ) of As(III) is 0.05 ng mL⁻¹ for graphite furnace atomic absorption spectrometry (GFAAS) with enrichment factor of 50, and the relative standard deviation (RSD) is 4.1% (n = 9, C = 5 ng mL⁻¹). The method has been applied to the determination of trace As(III) in water, and the recoveries of As(III) are 100 ± 10%. Correspondence: Yiwei Wu, Department of Chemistry and Environmental Engineering, Hubei Normal University, Huangshi 435002, P.R. China     

Design of a field flow system for the on-line spectrophotometric determination of phosphate, nitrite and nitrate in natural water and wastewater

This study describes the design and optimisation of a field flow system for the in-situ collection and on-line determination of phosphate, nitrate and nitrite by flow injection analysis-spectrophotometry. The method is based on the initial determination of phosphate as its phosphoantimonylmolybdenum blue complex which is then oxidized on-line by nitrite and the decrease in absorbance is monitored at 880 nm. Nitrate is determined as the difference between total and initial nitrite content in a separate flow after reduction to nitrite in a cadmium reductive column. The calibration curves were linear in the range 0–2.00 mg L⁻¹ P-phosphate, 0–10.00 mg L⁻¹ nitrite and 0–7.00 mg L⁻¹ nitrate with correlation coefficients of 0.9979, 0.9993 and 0.9995, respectively. The detection limits, calculated as 3S/N, were 0.15 mg L⁻¹ for P-phosphate, 0.17 mg L⁻¹ for nitrite and 0.09 mg L⁻¹ for nitrate. The reproducibility was below 3.0% (n = 7). Method validation in the analysis of natural water and wastewater samples revealed that it can efficiently be applied to the determination of the target analytes, with recoveries in the range of 92–108%. Correspondence: Athanasios G. Vlessidis, Laboratory of Analytical Chemistry, Department of Chemistry, University of Ioannina, Ioannina 45110, Greece     

Voltammetry and amperometric detection of tetracyclines at multi-wall carbon nanotube modified electrodes

The voltammetric behaviour and amperometric detection of tetracycline (TC) antibiotics at multi-wall carbon nanotube modified glassy carbon electrodes (MWCNT-GCE) are reported. Cyclic voltammograms of TCs showed enhanced oxidation responses at the MWCNT-GCE with respect to the bare GCE, attributable to the increased active electrode surface area. Hydrodynamic voltammograms obtained by flow-injection with amperometric detection at the MWCNT-GCE led us to select a potential value E _det = +1.20 V. The repeatability of the amperometric responses was much better than that achieved with bare GCE (RSD ranged from 7 to 12%), with RSD values for i _p of around 3%, thus demonstrating the antifouling capability of MWCNT modified electrodes. An HPLC method with amperometric electrochemical detection (ED) at the MWCNT-GCE was developed for tetracycline, oxytetracycline (OTC), chlortetracycline and doxycycline (DC). A mobile phase consisting of 18:82 acetonitrile/0.05 mol L⁻¹ phosphate buffer of pH 2.5 was selected. The limits of detection ranged from 0.09 μmol L⁻¹ for OTC to 0.44 μmol L⁻¹ for DC. The possibility to carry out multiresidue analysis is demonstrated. The HPLC-ED/MWCNT-GCE method was applied to the analysis of fish farm pool water and underground well water samples spiked with the four TCs at 2.0 × 10⁻⁷ mol L⁻¹. Solid-phase extraction was accomplished for the preconcentration of the analytes and clean-up of the samples. Recoveries ranged from 87 ± 6 to 99 ± 3%. Under preconcentration conditions, limits of detection in the water samples were between 0.50 and 3.10 ng mL⁻¹.     

Organosilica composite for preconcentration of phenolic compounds from aqueous solutions

A new adsorbent is proposed for the solid-phase extraction of phenol and 1-naphthol from polluted water. The adsorbent (TX-SiO₂) is an organosilica composite made from a bifunctional immobilized layer comprising a major fraction (91%) of hydrophilic diol groups and minor fraction (9%) of the amphiphilic long-chain nonionic surfactant Triton X-100 (polyoxyethylated isooctylphenol) (TX). Under static conditions phenol was quantitatively extracted onto TX-SiO₂ in the form of a 4-nitrophenylazophenolate ion associate with cetyltrimethylammonium bromide. The capacity of TX-SiO₂ for phenol is 2.4 mg g⁻¹ with distribution coefficients up to 3.4 × 10⁴ mL g⁻¹; corresponding data for 1-naphthol are 1.5 mg g⁻¹ and 3 × 10³ mL g⁻¹. The distribution coefficient does not change significantly for solution volumes of 0.025–0.5 L and adsorbent mass less than 0.03 g; 1–90 μg analyte can be easily eluted by 1–3 mL acetonitrile with an overall recovery of 98.2% and 78.3% for phenol and 1-naphthol, respectively. Linear correlation between acetonitrile solution absorbance (A ₅₄₀) and phenol concentration (C) in water was found according to the equation A ₅₄₀ = (6 ± 1) × 10⁻² + (0.9 ± 0.1)C (μmol L⁻¹) with a detection range from 1 × 10⁻⁸ mol L⁻¹ (0.9 μL g⁻¹) to 2 × 10⁻⁷ mol L⁻¹ (19 μL g⁻¹), a limit of quantification of 1 μL g⁻¹ (preconcentration factor 125), correlation coefficient of 0.936, and relative standard deviation of 2.5%. A solid-phase colorimetric method was developed for quantitative determination of 1-naphthol on adsorbent phase using scanner technology and RGB numerical analysis. The detection limit of 1-naphthol with this method is 6 μL g⁻¹ while the quantification limit is 20 μL g⁻¹. A test system was developed for naked eye monitoring of 1-naphthol impurities in water. The proposed test kit allows one to observe changes in the adsorbent color when 1-naphthol concentration in water is 0.08–3.2 mL g⁻¹.     

Electrochemical Study of 4-Nitrophenol at a Modified Carbon Paste Electrode

 A zeolite-modified carbon paste electrode (CPE) has been used for the determination of 4-nitrophenol by differential pulse voltammetry (DPV). The electrochemical reduction of 4-nitrophenol at −1.0 V is carried out in a Britton-Robinson medium at pH 3.5. The cyclic voltammetric (CV) behaviour has been investigated to study the nature of the process. Studies on the effect of pH were carried out over the pH range 2–9 with the Britton-Robinson buffer solution, and the influence of pH on peak height and peak potential was analyzed. A linear relationship between peak intensity and concentration is obtained in the range 0.2–10 mg L⁻¹, with a detection limit of 0.04 mg L⁻¹; a relative standard deviation of 1.5% for a 5 mg L⁻¹ 4-nitrophenol concentration and a relative error of 2.6% were also obtained (n=11). Received March 3, 1998. Revision December 10, 1998.     

Flow and Sequential Injection Manifolds for the Spectrophotometric Determination of Captopril Based on its Oxidation by Fe(III)

 Two new simple and rapid methods are reported for the accurate and precise spectrophotometric determination of captopril (CPL) using flow (FI) and sequential injection (SI) analysis. The methods are based on the fast oxidation of CPL by Fe(III). The produced Fe(II) reacts with 2,2′-dipyridyl-2-pyridylhydrazone (DPPH) in acidic medium to form a colored complex which is monitored spectrophotometrically at 535 nm. Both methods allow the determination of the analyte up to 1000 mg L⁻¹ at a sampling rate of 120 and 60 injections per hour for FI and SI, respectively. The methods are very precise [s _r=0.8 and 1.2% at 500 mg L⁻¹ CPL (n=12) for FI and SI, respectively] and the 3σ detection limits (c _L=4.0 and 7.0 mg L¹, respectively) are quite satisfactory. Their application to a variety of anti-hypertensive commercial pharmaceutical formulations showed excellent results (relative errors, e _r, < ± 1.6% in all cases compared to an official HPLC method), while common pharmaceutical excipients were found not to interfere. Recovery experiments further verified the accuracy of the developed methods, as the percent recoveries were in the range of 98.1–102.5%. Author for correspondence. E-mail: themelis@chem.auth.gr Received May 9, 2002; accepted January 8, 2003 Published online May 5, 2003     

Fluorescence enhancement assay for trace iron(II) using Pyr-tempo as a spin label fluorescent probe

Pyrene-tetramethylpiperidinyl (Pyr-Tempo) as a spin label fluorescent probe for iron(II) was synthesized. It exhibited weak fluorescence (λ_exc/λ_em = 346/399 nm) in aqueous solution due to an intramolecular quenching pathway. A method for determination of iron(II) was proposed based on the fluorescence enhancement of the probe in the presence of iron(II) in acidic medium. Under optimum conditions, the fluorescence enhancement of Pyr-Tempo is linearly proportional to the iron(II) concentration range of 6.0 × 10⁻⁸ to 9.6 × 10⁻⁶ mol L⁻¹ with a detection limit of 8.0 × 10⁻⁹ mol L⁻¹. The relative standard deviation (RSD) of six replicate measurements is 1.95% for 3.0 × 10⁻⁷ mol L⁻¹ iron(II). The developed spin label fluorescence probe is found to be rapidly and sensitively responsive to iron(II) with high selectivity compared to existing fluorescence methods. The proposed method was successfully applied to iron(II) detection in five real samples with satisfactory results obtained by manual UV/Vis spectrophotometry (standard method) with 1,10-phenanthroline.     

Sensitive determination of nitric oxide in some rat tissues using polymer monolith microextraction coupled to high-performance liquid chromatography with fluorescence detection

A simple, sensitive, selective, and low-cost method is proposed for rapidly determining nitric oxide (NO) in some rat tissues. Polymer monolith microextraction (PMME) using a poly(methacrylic acid–ethylene glycol dimethacrylate) (MAA-EGDMA) monolithic column was combined with derivatization of NO using 1,3,5,7-tetramethyl-8-(3′,4′-diaminophenyl)-difluoroboradiaza-s-indacene (TMDABODIPY), and this was used to analyze the derivatives of NO by high-performance liquid chromatography (HPLC) with fluorescence detection at λ _ex/λ _em = 498/507 nm. The baseline separation of TMDABODIPY and its NO derivative is performed under simple conditions in which a C₁₈ column is used and eluted with 50 mmol L⁻¹ ethanolamine and methanol. The conditions for the extraction of NO derivatives were optimized. The limit of detection of NO was 2 × 10⁻¹² mol L⁻¹ (S/N = 3). The linearity range of the method was 9 × 10⁻¹¹−4.5 × 10⁻⁸ mol L⁻¹. The interday and intraday relative standard deviations were less than 5%. The proposed method was successfully applied to the determination of NO levels in some rat tissue samples including heart, kidney, and liver with recoveries varying from 87.1 to 95.2%.     

Flow-Injection Spectrophotometric Determination of Diclofenac or Mefenamic Acid in Pharmaceuticals

 Two flow injection (FI) spectrophotometric methods are proposed for the determination of diclofenac (DCF) or mefenamic acid (MF) in bulk samples and pharmaceuticals. Both methods are based on the reaction of DCF or MF with potassium ferricyanide in a sodium hydroxide medium. The absorbance of the orange products obtained is measured at 455 nm for DCF and 465 nm for MF. The corresponding calibration graphs are linear over the range 0.20–20.0 mg L⁻¹ for DCF and 1.00–100 mg L⁻¹ for MF, while the limits of detection were 0.05 and 0.18 mg L⁻¹, respectively. Received March 27, 2000. Revision November 15, 2000.     

Polar herbicides,pharmaceutical products,perfluorooctanesulfonate (PFOS), perfluorooctanoate (PFOA), and nonylphenol and its carboxylates and ethoxylates in surface and tap waters around Lake Maggiore in Northern Italy

A survey of contamination of surface and drinking waters around Lake Maggiore in Northern Italy with polar anthropogenic environmental pollutants has been conducted. The target analytes were polar herbicides, pharmaceuticals (including antibiotics), steroid estrogens, perfluorooctanesulfonate (PFOS), perfluoroalkyl carboxylates (including perfluorooctanoate PFOA), nonylphenol and its carboxylates and ethoxylates (NPEO surfactants), and triclosan, a bactericide used in personal-care products. Analysis of water samples was performed by solid-phase extraction (SPE) then liquid chromatography–triple-quadrupole (tandem) mass spectrometry (LC–MS–MS). By extraction of 1-L water samples and concentration of the extract to 100 μL, method detection limits (MDLs) as low as 0.05–0.1 ng L⁻¹ were achieved for most compounds. Lake-water samples from seven different locations in the Southern part of Lake Maggiore and eleven samples from different tributary rivers and creeks were investigated. Rain water was also analyzed to investigate atmospheric input of the contaminants. Compounds regularly detected at very low concentrations in the lake water included: caffeine (max. concentration 124 ng L⁻¹), the herbicides terbutylazine (7 ng L⁻¹), atrazine (5 ng L⁻¹), simazine (16 ng L⁻¹), diuron (11 ng L⁻¹), and atrazine-desethyl (11 ng L⁻¹), the pharmaceuticals carbamazepine (9 ng L⁻¹), sulfamethoxazole (10 ng L⁻¹), gemfibrozil (1.7 ng L⁻¹), and benzafibrate (1.2 ng L⁻¹), the surfactant metabolite nonylphenol (15 ng L⁻¹), its carboxylates (NPE₁C 120 ng L⁻¹, NPE₂C 7 ng L⁻¹, NPE₃C 15 ng L⁻¹) and ethoxylates (NPE _n Os, n = 3-17; 300 ng L⁻¹), perfluorinated surfactants (PFOS 9 ng L⁻¹, PFOA 3 ng L⁻¹), and estrone (0.4 ng L⁻¹). Levels of these compounds in drinking water produced from Lake Maggiore were almost identical with those found in the lake itself, revealing the poor performance of sand filtration and chlorination applied by the local waterworks.     

HPLC determination of cefotaxime and cephalexine residues in milk and cephalexine in veterinary formulation

An HPLC method was developed and validated for the determination of the cephalosporins cefotaxime and cephalexine in skimmed bovine milk. The analytical column, Kromasil C₁₈ (250 mm × 4.0 mm, 5 μm) was operated at ambient temperature. Mobile phase consisted of CH₃OH-acetate buffer (pH = 4.0) and it was delivered isocratically at a flow rate of 1.0 mL · min⁻¹. Total analysis time was less than 5 min. Caffeine was used as internal standard (5 ng · μL⁻¹). UV detection was performed at 265 nm. Method validation was performed by means of intra-day (n = 5) and inter-day accuracy and precision (n = 8), sensitivity and linearity. Limits of detection (LOD) and limits of quantification (LOQ) were 0.1 and 0.3 ng · μL⁻¹, respectively. The method was applied to the analysis of a veterinary drug (CEPOREX) containing cephalexine. The results were quite accurate with the relative error varying from −8.0 to −3.5%. Solid-phase extraction was applied to remove all matrix interference from milk samples. High extraction recoveries (average 84–121%) were achieved by using Abselut NEXUS cartridges with acetonitrile as eluent and a rinsing step with water and n-butanol. A pre-concentration step was necessary in a 1/10 level to reach the EU MRL concentration level (100 μg · kg⁻¹). RSD values were less than 7% for both cephalosporins. Correspondence: Ioannis N. Papadoyannis, Laboratory of Analytical Chemistry, Department of Chemistry, Aristotle University of Thessaloniki, GR-54124 Thessaloniki, Greece     

Determination of butoxyacetic acid (biomarker of ethylene glycol monobutyl ether exposure) in human urine candidate reference material

Ethylene glycol monobutyl ether (EGBE), an industrial solvent, is absorbed by the body not only by inhalation but also by dermal absorption (liquid or vapour). EGBE is metabolized to butoxyacetic acid (BAA). Pooled freeze-dried urine candidate reference material (RM) was prepared from urine obtained from persons occupationally exposed to EGBE. This material has the advantage of containing butoxyacetic acid in both the free and conjugated (glutamine and glycine) forms, as found in native urine. In all GC method modifications used, acid hydrolysis was used to release BAA from its conjugated form. The amount of butoxyacetic acid in homogeneity and stability testing was measured by GC after derivatisation with N-tert-butyldimethylsilyl-N-methyltrifluoroacetamide. Detection was by MS in EI mode, in the authors’ laboratory. For interlaboratory comparison of the reference material GC methods with MS, FID, and ECD were used. Different extraction solvents (dichloromethane–isopropanol 2:1, ethyl acetate, or dichloromethane) and derivatisation reagents (trimethylsilyldiazomethane, N-tert-butyldimethylsilyl-N-methyltrifluoroacetamide) were used. Using ANOVA (at the statistical level α = 0.05) no changes were found in the concentration of butoxyacetic acid during fifteen month isochronous stability testing, or in homogeneity testing. The uncertainty contributions were u _h = 8.8 mg L⁻¹ and u _s = 6.5 mg L⁻¹. The concentration of butoxyacetic acid in freeze-dried urine RM was evaluated from the results of eight laboratory data sets within an interlaboratory comparison by use of the interactive statistical software IPECA. The contribution to total uncertainty derived from interlaboratory comparison was u _i = 12.7 mg L⁻¹. The reference value (c = 273 ± 33 mg L⁻¹) is an unweighted arithmetic average of accepted results. The value is traceable to the pure butoxyacetic acid (98% w/w; Acros Organic #257760010) used as calibrant. The uncertainty given is combined expanded uncertainty derived from the results from interlaboratory comparison, and from homogeneity and stability tests (k = 2). The reference material will be used to verify method performance in the biological monitoring of occupational exposure to EGBE.     

Inorganic Arsenic and Selenium Determination Using Miniaturised Isotachophoresis

A new method allowing the simultaneous determination of arsenic(V), selenium(IV) and selenium(VI) using miniaturised isotachophoresis has been developed. The method uses 0.02 M nitric acid buffered to pH 5.5 with histidine as the leading electrolyte. Using a miniaturised poly(methyl methacrylate) chip device with an integrated conductivity detector, separations of model samples and an industrial process stream sample were achieved. Limits of detection were calculated to be 0.85 mg L⁻¹ for arsenic(V), 0.95 mg L⁻¹ for selenium(IV) and 1.0 mg L⁻¹ for selenium(VI). A method for the analysis of arsenic(III), using a glycolic acid based leading electrolyte to eliminate carbonate interference is also presented.     

Full automation of solid-phase microextraction/on-fiber derivatization for simultaneous determination of endocrine-disrupting chemicals and steroid hormones by gas chromatography–mass spectrometry

A fully automated method using direct immersion solid-phase microextraction (DI-SPME) and headspace on-fiber silylation for simultaneous determinations of exogenous endocrine-disrupting chemicals (EDCs) and endogenous steroid hormones in environmental aqueous and biological samples by gas chromatography–mass spectrometry (GC-MS) was developed and compared to a previously reported manual method. Three EDCs and five endocrine steroid hormones were selected to evaluate this method. The extraction and derivatization time, ion strength, pH, incubation temperature, sample volume, and extraction solvent were optimized. Satisfactory results in pure water were obtained in terms of linearity of calibration curve (R ²=0.9932–1.0000), dynamic range (3 orders of magnitude), precision (4–9% RSD), as well as LOD (0.001–0.124 μg L⁻¹) and LOQ (0.004–0.413 μg L⁻¹), respectively. These results were similar to those obtained using a manual method, and moreover, the precision was improved. This new automated method has been applied to the determinations of target compounds in real samples used in our previous study on a manual SPME method. Exogenous octylphenol (OP), technical grade nonylphenol (t-NP), and diethylstilbestrol (DES) were at 0.13, 5.03, and 0.02 μg L⁻¹ in river water and 3.76, 13.25, and 0.10 μg L⁻¹ in fish serum, respectively. Natural steroid hormones estrone (E₁), 17β-estradiol (E₂), and testosterone (T) were at 0.19, 0.11, and 6.22 μg L⁻¹ in river water; and in female fish serum E₁, E₂, and pregnenolone (PREG) were at 1.37, 1.95, and 6.25 μg L⁻¹, respectively. These results were confirmed by the manual method. The developed fully automated SPME and on-fiber silylation procedures showed satisfactory applications in environmental analysis and the performances show improved precision and a reduced analysis time compared to the manual method.     

Development of a sequential injection–square wave voltammetry method for determination of paraquat in water samples employing the hanging mercury drop electrode

This work describes the development and optimization of a sequential injection method to automate the determination of paraquat by square-wave voltammetry employing a hanging mercury drop electrode. Automation by sequential injection enhanced the sampling throughput, improving the sensitivity and precision of the measurements as a consequence of the highly reproducible and efficient conditions of mass transport of the analyte toward the electrode surface. For instance, 212 analyses can be made per hour if the sample/standard solution is prepared off-line and the sequential injection system is used just to inject the solution towards the flow cell. In-line sample conditioning reduces the sampling frequency to 44 h⁻¹. Experiments were performed in 0.10 M NaCl, which was the carrier solution, using a frequency of 200 Hz, a pulse height of 25 mV, a potential step of 2 mV, and a flow rate of 100 μL s⁻¹. For a concentration range between 0.010 and 0.25 mg L⁻¹, the current (i _p, μA) read at the potential corresponding to the peak maximum fitted the following linear equation with the paraquat concentration (mg L⁻¹): i _p = (−20.5 ± 0.3)C _paraquat − (0.02 ± 0.03). The limits of detection and quantification were 2.0 and 7.0 μg L⁻¹, respectively. The accuracy of the method was evaluated by recovery studies using spiked water samples that were also analyzed by molecular absorption spectrophotometry after reduction of paraquat with sodium dithionite in an alkaline medium. No evidence of statistically significant differences between the two methods was observed at the 95% confidence level.     

Preconcentration and Voltammetric Determination of the Antihypertensive Doxazosin on a C8 Modified Carbon Paste Electrode

 An electrochemical study of the doxazosin oxidative process at carbon paste electrodes using different voltammetric techniques has been carried out. The process is irreversible and controlled by adsorption, giving rise to an oxidation wave around 1.0 V in citric acid-citrate buffer (pH 3.0). A mechanism based on the oxidation of the amine group is postulated. Two methods based on adsorptive stripping (AdS) of doxazosin at the C₈-modified carbon paste electrode (C₈-MCPE), before its voltammetric determination, are studied, using differential pulse voltammetry (DPV) and square wave voltammetry (SWV) as redissolution techniques. By means of AdS-DPV and C₈-MCPE, doxazosin can be determined over the 1.0 × 10⁻⁹ to 3.0 × 10⁻⁸ mol L⁻¹ range with a variation coefficient of 2.2% (2.0 × 10⁻⁸ mol L⁻¹) and a limit of detection of 7.4 ×10⁻¹⁰ mol L⁻¹. If AdS-SWV is used, a linear range from 1.0 × 10⁻⁹ to 4.0 × 10⁻⁸ mol L⁻¹ is obtained, the variation coefficient being 2.8% (2.0 × 10⁻⁸ mol L⁻¹, and the limit of detection reached 7.7 × 10⁻¹⁰ mol L⁻¹. The AdS-DPV procedure was applied to the determination of doxazosin in urine and formulations. Received March 13, 1999. Revision December 23, 1999.     

Electrochemical determination of uric acid using a mesoporous SiO2-modified electrode

A mesoporous SiO₂-modified carbon paste electrode for the determination of uric acid is described. Owing to the regular and specific mesoporous channels, numerous active sites and a large surface area, the mesoporous SiO₂-modified electrode greatly increases the oxidation peak current of uric acid. Based on this, a highly sensitive, rapid and convenient electrochemical method was developed for the determination of uric acid after optimizing the experimental parameters (supporting electrolyte, content of mesoporous SiO₂, accumulation potential and time). The linear range is from 2.5 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, and the limit of detection is estimated to be 8.0 × 10⁻⁸ mol L⁻¹. The relative standard deviation for 10 mesoporous SiO₂-modified electrodes is 5.8%. The method was used to determine uric acid in human serum samples. Correspondence: Kangbing Wu, Department of Chemistry, Huazhong University of Science and Technology, Wuhan 430074, P.R. China     

Determination of rutin using a CeO2 nanoparticle-modified electrode

CeO₂ nanoparticles approximately 12 nm in size were synthesized and subsequently characterized by XRD, TEM and UV-vis spectroscopy. Then, a gold electrode modified with CeO₂ nanoparticles was constructed and characterized by electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The modified electrode demonstrated strong catalytic effects with high stability towards electrochemical oxidation of rutin. The anodic peak currents (measured by differential pulse voltammetry) increased linearly with the concentration of rutin in the range of 5.0 × 10⁻⁷–5.0 × 10⁻⁴ mol · L⁻¹. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol · L⁻¹. The relative standard deviation (RSD) of 8 successive scans was 3.7% for 5.0 × 10⁻⁶ mol · L⁻¹ rutin. The method showed excellent sensitivity and stability, and the determination of rutin in tablets was satisfactory.