Numerical simulation of the effects of plate separation and inclination on heat transfer in buoyancy driven open channels

 Effects of plate separation and inclination on free convection between asymmetrically heated vertical and inclined parallel plates have been simulated. The upper isothermally heated plate is facing downwards, the lower plate is passively heated by the upper one. The plate inclinations are chosen to be 0^∘, 30^∘, 45^∘ with respect to vertical position. Three-dimensional laminar numerical simulations are obtained by solving the full elliptic governing equations using a commercial finite volume based computational fluid dynamics (CFD) code. Comparisons of computational results with experiments and data from the literature are made in terms of relevant dimensionless numbers. It was observed that plate spacing and inclination influence the overall heat transfer rate. Received on 3 November 1998     

Numerical study of simultaneous natural convection heat transfer from both surfaces of a uniformly heated thin plate with arbitrary inclination

 Numerical studies were conducted to investigate the natural convection heat transfer around a uniformly heated thin plate with arbitrary inclination in an infinite space. The numerical approach was based on the finite volume technique with a nonstaggered grid arrangement. For handling the pressure–velocity coupling the SIMPLE-algorithm was used. QUICK scheme and first order upwind scheme were employed for discretization of the momentum and energy convective terms respectively. Plate width and heating rate were used to vary the modified Rayleigh number over the range of 4.8×10⁶ to 1.87×10⁸. Local and average heat transfer characteristics were compared with regarding to the inclination angle. The empirical expressions for local and average Nusselt number were correlated. It has been found that for inclination angle less than 10^∘, the flow and heat transfer characteristics are complicated and the average Nusselt number can not be correlated by one equation while for inclination angle larger than 10^∘, the average Nusselt number can be correlated into an elegant correlation. Received on 18 April 2001 / Published online: 29 November 2001     

Experimental investigation of mixed convection in a rectangular duct with a heated plate in the middle of cross section

The flow and heat transfer in an inclined and horizontal rectangular duct with a heated plate longitudinally mounted in the middle of cross section was experimentally investigated. The heated plate and rectangular duct were both made of highly conductive materials, and the heated plate was subjected to a uniform heat flux. The heat transfer processes through the test section were under various operating conditions: Pr ≈ 0.7, inclination angle ϕ = −60° to +60°, Reynolds number Re = 334–1,911, Grashof number Gr = 5.26 × 10²–5.78 × 10⁶. The experimental results showed that the average Nusselt number in the entrance region was 1.6–2 times as large as that in the fully developed region. The average Nusselt numbers and pressure drops increased with the Reynolds number. The average Nusselt numbers and pressure drops decreased with an increase in the inclination angle from −60° to +60° when the Reynolds number was less than 1,500. But when the Reynolds number increased to over about 1,800, the heat transfer coefficients and pressure drops were independent of inclination angles.     

Experimental study of air natural convection on metallic foam-sintered plate

The natural convection on metallic foam-sintered plate at different inclination angles was experimentally studied. Seven copper foam samples with different pore densities (10–40 pore per inch), porosities (0.90–0.95), and aspect ratios (the ratio of foam thickness to sample length, 0.1–0.5) were measured at inclination angles of 0° (vertical orientation), 15°, 30°, 45°, 60°, 75°, 90° (horizontal orientation). The heat conduction and natural convection inside the foam both contributed to the total heat transfer. Although, the form and viscous drag, which are influenced by permeability and viscous friction in the thermal boundary layer respectively, tend to suppress the natural convection, the heat transfer was finally enhanced by the foam sintered surface due to large surface area extension. Optimum inclination range 60–75° corresponding to maximum average Nu number was found in the heat flux range of 600–1800 W/m². The sintered foam surface with lower porosity and pore density was recommended for heat transfer enhancement. Particularly, the sample with porosity 0.9, pore density of 10 PPI, aspect ratio of 0.5 offered the highest average Nu number among the studied samples. An empirical correlation for modified Nusselt number at isoflux boundary condition considering the foam morphology parameter and inclination angle was proposed within deviation ±15% between the correlation and the experimental data.     

Laminar natural convection in inclined enclosures bounded by a solid wall

Laminar natural convection has been studied in enclosures bounded by a solid wall with its outer boundary at constant temperature while the opposing side has a constant heat flux. Two-dimensional equations of conservation of mass, momentum and energy, with the Boussinesq approximation are solved using a finite difference method. The numerical procedure adopted is based on the SIMPLER algorithm. Various parameters were: Rayleigh number (from 10³ to 10⁶), dimensionless conductivity of bounding wall (from 1 to 10) and dimensionless wall width (from 0.15 to 0.5), aspect ratio (from 0.5 to 1) and the inclination angle (from 30^° to 180^°). The results are reduced in terms of the normalized Nusselt number as a function of the Rayleigh number, and other dimensionless parameters. The isotherms and streamlines are produced for various Rayleigh numbers and geometrical conditions. It is found that the heat transfer is an increasing function of the Rayleigh number, wall to fluid conductivity ratio, enclosure aspect ratio and a decreasing function of the wall thickness. It passes from a maximum for the inclination angle of about 80^°.     

Heat transfer from a flat surface to an inclined impinging jet

An experimental study was carried out to investigate the effect of the inclination jet on convection heat transfer to horizontal flat plate. Local heat transfer determined as a function is of three parameters including inclination angle of the air jet relative to the plate in range of 90° ≤ θ ≤ 45°, jet-to-plate spacing in range of 2 ≤ L/D ≤ 8 and Reynolds number in range of 1,500 ≤ Re ≤ 30,000. The results show that the maximum heat transfer point moves towards the uphill side of the plate and the maximum heat transfer decreases as the inclination angle decreases. The correlations were conducted to predict maximum and local Nusselt number as a function of Re, θ, L/D, and x/D for a specific three regions.     

Heat transfer augmentation between impinging circular air jet and flat plate using finned surfaces and vortex generators

An experimental investigation is performed to study the effect of the finned surfaces and surfaces with vortex generators on the local heat transfer coefficient between impinging circular air jet and flat plate. Reynolds number is varied between 7000 and 30,000 based on the nozzle exit condition and jet to plate spacing between 0.5 and 6 nozzle diameters. Thermal infrared imaging technique is used for the measurement of local temperature distribution on the flat plate. Fins used are in the form of cubes of 2 mm size spaced at a pitch of 5 mm on the target plate and hexagonal prism of side 2.04 mm and height of 2 mm spaced at a pitch of 7.5 mm. Vortex generators in the form of a equilateral triangle of side 4 mm are used. Effect of number of rows of vortex generators, radius of a row, number of vortex generators in a row and inclination angle (i.e., the angle between the plane of the target plate and the plane of the vortex generators) on Nusselt number is studied. It is observed that the heat transfer coefficient between the impinging jet and the target plate is sensitive to the shape of the fin. The increase in the heat transfer coefficient up to 77% depending on the shape of the fin, nozzle plate spacing and the Reynolds number is observed. The augmentation in the heat transfer for the surfaces vortex generators are higher than that of the finned surfaces. The heat transfer augmentation in case of vortex generator is as high as 110% for a single row of six vortex generators at a radius of 1 nozzle diameter as compared to the smooth surface at a given nozzle plate spacing of 1 nozzle diameter and a Reynolds number of 25,000 at extreme radial location.     

Experimental study of the effect of spray inclination on ultrafast cooling of a hot steel plate

The ultrafast cooling that occurs during high mass flux air-atomized spray impingement on a hot 6 mm thick stainless steel plate has been studied experimentally in terms of the nozzle inclination between 0° and 60°. The average mass flux of water used in the study accounts to 510 kg/m² s. The coolants used in the study are pure water and surfactant water of 600 ppm concentration. The initial temperature of the plate has been maintained at 900 °C, which is the temperature of a hot strip on run-out table in steel industry. The transient surface heat flux and temperature histories have been estimated by an inverse heat solver using measured temperature input data. Heat transfer results demonstrates that optimum cooling efficiency (~2.76 MW/m², 194 °C/s) for pure water has been achieved at 30° nozzle orientation. The inclined nozzle has not been found beneficial when surfactant water is used as the coolant.     

Transient conjugated mixed-convective heat transfer in a vertical plate channel with one wall heated discretely

 This study presents a numerical solution of the unsteady conjugated mixed-convection heat transfer in a vertical plate channel with one wall suddenly subjected to either isoflux or isothermal discrete heat sources. The effects of the dimensionless heat source length H ₁, the dimensionless spacing between heat sources H ₂, the dimensionless channel length L, the dimensionless heated-plate thickness B _l, the wall-to-fluid conductivity ratio K and the ratio of Grashof number to Reynolds number Gr/Re on the interface heat flux, Nusselt number and bulk fluid temperature are discussed in detail. Results show that the discrete heating can cause the heat transfer direction conversely from the fluid to the heated plate during the transient period, which is more significant for the cases with larger L and H ₂. For the system with isoflux discrete heat sources, the time required to reach the steady-state is shorter for larger H ₂. While the trend is reverse for system with isothermal discrete heat sources. Additionally, a higher ratio of the input energy is axially conducted through the plate wall from heated sections to unheated regions for a larger H ₂ and B _l or smaller L. Received on 9 November 1998     

MHD mixed convective heat transfer flow about an inclined plate

Mixed convection heat transfer about a semi-infinite inclined plate in the presence of magneto and thermal radiation effects is studied. The fluid is assumed to be incompressible and dense. The nonlinear coupled parabolic partial differential equations governing the flow are transformed into the non-similar boundary layer equations, which are then solved numerically using the Keller box method. The effects of the mixed convection parameter R _i, the angle of inclination α, the magnetic parameter M and the radiation–conduction parameter R _d on the velocity and temperature profiles as well as on the local skin friction and local heat transfer parameters. For some specific values of the governing parameters, the results are compared with those available in the literature and a fairly good agreement is obtained.     

Adaptive neuro-fuzzy inference system (ANFIS) to predict the forced convection heat transfer from a v-shaped plate

This paper reports the application of the adaptive neuro-fuzzy inference system to model the forced convection heat transfer from v-shaped plate internal surfaces exposed to an air impingement slot jet. The aim of the current study is to consider the effects of the angle of the v-shaped plate $ (\Upphi ) $ , slot-to-plate spacing ratio (Z/W) and the Reynolds number (Re) variation on the average heat transfer from the v-shaped plate.     

Natural convection in inclined rectangular enclosures with perfectly conducting fins attached on the heated wall

The natural convection heat transfer in inclined rectangular enclosures with perfectly conducting fins attached to the heated wall is numerically studied. The parameters governing this problem are the Rayleigh number (10²≤Ra≤2×10⁵), the aspect ratio of the enclosures (2.5≤A=H′/L′≤∞), the dimensionless lengths of the partitions (0≤B=?′/L′≤1), the aspect ratio of micro-cavities (A≤C=h′/L′≤0.33), the inclination angle (0≤φ≤60^°) and the Prandtl number (Pr=0.72). The results indicate that the heat transfer through the cover is considerably affected by the presence of the fins. At low Rayleigh numbers, the heat transfer regime is dominated by conduction. When B≈0.75 and C≈0.33, the heat transfer through the cold wall decreases considerably. This trend is enhanced when the enclosure is inclined. Useful engineering correlations are derived for practical applications.     

Numerical and experimental studies of natural convective heat transfer from vertical and inclined narrow isothermal flat plates

Natural convective heat transfer from an isothermal narrow flat plate embedded in a plane adiabatic surface and inclined at moderate positive and negative angles to the vertical has been numerically and experimentally studied. The solution has the Rayleigh number, the dimensionless plate width, the angle of inclination, and the Prandtl number as parameters. Attention was restricted to a Prandtl number of 0.7. The numerical results have been obtained for Rayleigh numbers between 10³ and 10⁷ for dimensionless plate widths of between 0.3 and 1.2 and for angles of inclination between +45° and −45°. In the experimental study, results have been obtained for Rayleigh numbers between 4 × 10² and 10⁵ for dimensionless plate widths of 0.4 and 2.5 and for angles of inclination between +45° and −45° to the vertical. Empirical equations for the heat transfer rate have been derived.     

Similarity solution of mixed convection over a horizontal moving plate

Investigation to the mixed convective heat and mass transfer over a horizontal plate has been carried out. By applying transformation group theory to analysis of the governing equations of continuity, momentum, energy and diffusion, we show the existence of similarity solution for the problem provided that the temperature and concentration at the wall are proportional to x ^4/(7-5n) and that the moving speed of the plate is proportional to x ^(3-n)/(7-5n), and further obtain a similarity representation of the problem. The similarity equations have been solved numerically by a fourth-order Runge–Kutta scheme. The numerical results obtained for Pr=0.72 and various values of the parameters Sc, K ₁, K ₂ and K ₃ reveals the influence of the parameters on the flow, heat and mass transfer behavior.     

Experimental investigation of flow and heat transfer in rectangular cross-sectioned duct with baffles mounted on the bottom surface with different inclination angles

In this study, steady-state forced convection heat transfer and pressure drop characteristics in a horizontal rectangular cross-sectioned duct, baffles mounted on the bottom surface with different inclination angles were investigated experimentally in the Reynolds number range from 1 × 10³ to 1 × 10⁴. The study was performed under turbulent flow conditions. Effects of different baffle inclination angles on flow and heat transfer were studied. Results are also presented in terms of thermal enhancement factor. It is observed that increasing in baffle inclination angle enhances the heat transfer and causes an increase in pressure drop in the duct.     

Natural convection in an inclined quadrantal cavity heated and cooled on adjacent walls

Natural convective flow and heat transfer in an inclined quadrantal cavity is studied experimentally and numerically. The particle tracing method is used to visualize the fluid motion in the enclosure. Numerical solutions are obtained via a commercial CFD package, Fluent. The working fluid is distilled water. The effects of the inclination angle, ? and the Rayleigh number, Ra on fluid flow and heat transfer are investigated for the range of angle of inclination between 0° ? ? ? 360°, and Ra from 10⁵ to 10⁷. It is disclosed that heat transfer changes dramatically according to the inclination angle which affects convection currents inside, i.e. flow physics inside. A fairly good agreement is observed between the experimental and numerical results.     

Turbulent heat transfer in a flat plate boundary layer disturbed by a cylinder

Augmentation of heat transfer from a flat plate using a turbulence promoter has been studied. A circular cylinder 8 mm in diameter was placed in the turbulent boundary layer detached from the flat plate. It was located parallel to the plate and perpendicular to the flow direction. Clearance, c, between the cylinder and the flat plate was varied in nine steps: c=0, 1, 2, 3, 4, 6, 11, 20 and 29.5 mm. Measurements were made of the local heat transfer coefficients, mean velocity profiles, turbulence intensity profiles, static pressure and skin friction. Experimental results showed that the heat transfer deterioration which occurs just downstream of the cylinder at c=0 mm can be removed by displacing the cylinder a small distance from the wall. The improvement in heat transfer is mainly due to the unsteadiness of the recirculating flow on the plate and the effect of intense turbulence arriving at the near wall region from the lower shear layer of the cylinder wake. Heat transfer augmentation is most effective when c=4 mm and becomes less effective when c is increased more than 6 mm. The enhancement disappears far downstream from the cylinder.     

Thermal dispersion effects on non-Darcy natural convection over horizontal plate with surface mass flux

Summary The effect of surface mass flux on the non-Darcy natural convection over a horizontal flat plate in a saturated porous medium is studied using similarity solution technique. Forchheimer extension is considered in the flow equations. The suction/injection velocity distribution has been assumed to have power function form Bx ^l , similar to that of the wall temperature distribution Ax ⁿ , where x is the distance from the leading edge. The thermal diffusivity coefficient has been assumed to be the sum of the molecular diffusivity and the dynamic diffusivity due to mechanical dispersion. The dynamic diffusivity is assumed to vary linearly with the velocity component in the x direction, i.e. along the hot wall. For the problem of constant heat flux from the surface (n=1/2), similarity solution is possible when the exponent l takes the value −1/2. Results indicate that the boundary layer thickness decreases whereas the heat transfer rate increases as the mass flux parameter passes from the injection domain to the suction domain. The increase in the thermal dispersion parameter is observed to favor the heat transfer by reducing the boundary layer thickness. The combined effect of thermal dispersion and fluid suction/injection on the heat transfer rate is discussed. Received 7 December 1995; accepted for publication 7 January 1997     

Experimental investigation of natural convection heat transfer in horizontal and inclined annular fluid layers

In the present study, an experimental investigation of heat transfer and fluid flow characteristics of buoyancy-driven flow in horizontal and inclined annuli bounded by concentric tubes has been carried out. The annulus inner surface is maintained at high temperature by applying heat flux to the inner tube while the annulus outer surface is maintained at low temperature by circulating cooling water at high mass flow rate around the outer tube. The experiments were carried out at a wide range of Rayleigh number (5 × 10⁴ < Ra < 5 × 10⁵) for different annulus gap widths (L/D _o = 0.23, 0.3, and 0.37) and different inclination of the annulus (α = 0°, 30° and 60°). The results showed that: (1) increasing the annulus gap width strongly increases the heat transfer rate, (2) the heat transfer rate slightly decreases with increasing the inclination of the annulus from the horizontal, and (3) increasing Ra increases the heat transfer rate for any L/D _o and at any inclination. Correlations of the heat transfer enhancement due to buoyancy driven flow in an annulus has been developed in terms of Ra, L/D _o and α. The prediction of the correlation has been compared with the present and previous data and fair agreement was found.     

Heat transfer studies of the oblique impingement of round jets upon a curved surface

 The effect of jet inclination of the local heat transfer under an obliquely impinging round air jet striking on isothermal circular cylinder is experimentally investigated. The circumferential heat transfer distribution as well as axial Nusselt number is measured. The considered parameters are jet Reynolds number in range of 3800–40,000, and jet inclination angle, ranging from 90 to 20. The experiments are carried out for nozzle sizes, d=3, 5 and 7 mm, and separation distance from 7 to 30 of the nozzle diameter. The output results indicated that the point of maximum heat transfer along the x-axis is shifted upstream and the local heat transfer distribution changed as a function of jet inclination. The magnitude of the shift was found to be significantly higher than that observe for a flat plate. The increasing inclination caused increasing asymmetry around the point of maximum heat transfer, with the upstream side of heat transfer profile dropping off more rapidly than the downstream side. Correlations of both the magnitude and shift of maximum heat transfer point are presented. The surface average heat transfer rate is calculated and compared with the normal impingement. Received on 5 June 2000 / Published online: 29 November 2001