EFFECT OF 2—HYDROXYETHYL METHACRYLATE ON SEMIBATCH EMULSIFIER—FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE AND BUTYL ACRYLATE

The semibatch emulsifier-free emulsion copolymerization of methyl methacrylate (MMA) and butyl acrylate(BA) in the presence of 2-hydroxyethyl methacrylate(HEMA) initiated by K2S2O8(PSP) was studied.The latex particles can maintain an appreciable stability during the emulsifier-free emulsion copolymerization of MMA and BA in the presence of HEMA.The average particle diameter increase with an increase of total solids content,HEMA content,PSP content,ionic strength of the system and monomer feed rate,and decrease with the monomer feed ration from 3/1 (MMA/BA:molar ration).to 1/3.The stability of this reaction system is improved by adding HEMA as nonionic comonomer,High solids content (50%) latex with monodisperse particle can be obtained using this process.     

Semibatch Emulsifier-free Emulsion Copolymerization of Methyl Methacrylate and n-Butyl Acrylate in the Presence of 2-Hydroxyethyl Methacrylate

ThemethodsofimProvingthestabilityofemulsifier-freeemulsionpolymerizationhavebeenreportedinliteraturet(a)choosingionizableinitiators,suchaspotassiumpersulfate'andazo-bis(isobutyramidinehydrochloride)';(b)copolymerizationwithhydrophiliccomonomers,whichinvolvestheionictypesuchascarboxylicmonomers',sulfoderivativesofvinylmonomers',andthenonionictypesuchasglycidylmethacrylate';(c)copolymerizationwithsurface-activemonomers,suchassulfodecylslyrylether';(d)addingorganicsolventstothesystem,suchasmethano…     

单体极性对甲基丙烯酸甲酯/丙烯酸丁酯/甲基丙烯酸钠无皂乳液共聚合的影响

研究了少量甲基丙烯酸钠（ＮａＭＡ）存在下单体极性对甲基丙烯酸甲酯（ＭＭＡ）／丙烯酸丁酯（ＢＡ）无皂乳液共聚合的影响．单体极性降低，使粒径减小、聚合速率提高、乳液表面张力和粘度降低、粒子表面电荷密度增大、聚合物分子量提高．ＭＭＡ／ＮａＭＡ无皂乳液聚合物只呈现一个玻璃化温度Ｔｇ，ＢＡ／ＮａＭＡ无皂乳液聚合物呈现两个Ｔｇ，ＭＭＡ／ＢＡ比为２∶１～１∶２的ＭＭＡ／ＢＡ／ＮａＭＡ无皂乳液聚合物呈现四个Ｔｇ，这是由于粒子外面相对富含ＯＳＯ－３和ＣＯＯ－基聚合物的亚层溶解了较多的水，使ＢＡ向粒子中心扩散，ＭＭＡ向外扩散，造成组成差异和相分离而引起的．     

Influence of hydrophobic monomers on secondary nucleation of hydroxyl‐functionalized latexes

The influence of butyl acrylate (BA) and methyl methacrylate (MMA) on hydroxyl functionalized latexes was investigated. The hydrophobicity of the monomer feed was varied via the BA/MMA ratio. In addition to monitoring the effect of hydrophobic monomer feed on secondary nucleation, the polymerization kinetics and final latex properties were also obtained for comparison. Five different BA to MMA molar ratios were combined with five 2‐hydroxyethyl methacrylate (HEMA) concentrations (0, 10, 20, 30 and 40 mol% in monomer composition). All latexes were synthesized through seeded semibatch emulsion polymerization process. Particle size distributions and average particle sizes of the latexes were determined by dynamic light scattering (DLS) and qualitatively compared with transmission electron microscope (TEM) images. The BA to MMA ratio significantly influences the boundary HEMA concentration at which homogeneous secondary nucleation occurs. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2190–2202     

GHD室温自交联乳液的聚合及贮存稳定性

采用半连续种子乳液聚合技术合成了含甲基丙烯酸缩水甘油酯(GMA)、甲基丙烯酸羟乙酯(HEMA)和甲基丙烯酸二甲氨基乙酯(DMAEMA)的室温自交联乳液(GHD).实验结果表明,在甲基丙烯酸甲酯(MMA)-丙烯酸丁酯(BA)-GMA种子乳液存在下,聚合温度升高,聚合过程稳定性下降,但乳液的贮存稳定性提高;乳化单体滴加速度加快,种子聚合物的玻璃化温度升高,可减少聚合过程的交联凝聚作用,提高聚合过程的稳定性;而HEMA和DMAEMA用量增加对聚合过程的稳定性没有明显影响,但使乳液的贮存稳定性下降.官能团间的交联凝聚作用可能是影响室温自交联乳液聚合及贮存过程稳定性的关键因素.     

Studies on the Preparation of Stable and High Solid Content Emulsifier-Free Poly(MMA/BA/HEA) Latex with the Addition of AMPS and Characterization of the Obtained Copolymers

The 2-acrylamido -2-methylpropane sulfonic acid (AMPS) was used as a reactive comonomer for the methyl methacrylate (MMA), n-butyl acrylate (BA) and 2-hydroxyethyl acrylate (HEA) emulsifier-free emulsion copolymerization system to obtain latices of stable and high-solid content (50 wt%).The polymerization and storage process is very stable, and the emulsion could store at room temperature for more than six months with the addition of AMPS. Properties of the latices, such as stability, flow behavior, particles diameter and morphology were studied. In addition, physical properties of the obtained copolymers, such as water resistance, glass transition temperature (T_g) were also investigated. The final size of the latex particles is 200～300 nm in diameter. Compared with the copolymers that were prepared by surfactant emulsion polymerization water resistance is greatly improved.     

功能单体α-烯烃磺酸钠用于无皂乳液共聚合

用工业原料α-烯烃磺酸钠(AOS)作为功能单体与甲基丙烯酸甲酯(MMA)和丙烯酸丁酯(BA)进行了乳液共聚合,通过测定AOS与MAA的竞聚率,确定了适宜的聚合方式为连续加料法.使用5%AOS制备了高固含量(>60%)的胶乳,并与用十二烷基硫酸钠(SDS)作乳化剂时该体系的乳液共聚合进行了比较.AOS是影响乳液稳定性和胶粒大小的主要因素,当AOS含量为单体总质量的1%时可以得到固含量大于40%粒径小于100 nm的乳液;当AOS含量为5%时可以得到固含量大于60%的乳液.两种情况下胶粒粒径分散性均较窄,明显优于同样条件下用SDS制备的胶乳.使用1%AOS制得的胶乳静置1年后粒径及其分布基本保持不变.     

无皂高分子纳米胶乳粒子的制备与稳定

在微波辐照下,以过硫酸钾(KPS)为引发剂,丙酮水溶液(质量比1∶ 1)为分散介质,进行了苯乙烯(ST)和其它共聚单体:甲基丙烯酸甲酯(MMA)、甲基丙烯酸丁酯(BMA)、丙烯酸乙酯(EA)及顺丁烯二酸酐(BDA)的无皂乳液聚合,得到了稳定的纳米胶乳粒子.讨论了共聚单体的种类和浓度对粒子水化半径的影响.增加配方中亲水性单体含量,使引发反应中引发剂的消耗量增加,粒子表面电荷密度增大,同时亲水性增加,油水界面张力减小,粒子变得稳定,有利于小粒子的生成.粒子的大小随亲水性单体的含量呈曲线关系,曲线上有最低点.     

离子型表面活性单体存在下的MMA/BA乳液聚合(Ⅰ)——表面活性单体的合成及其(共)聚合活性

合成了两种离子型表面活性单体(Surfmer)磺化-十二醇-烯丙基甘油-丁二酸酯钠盐(ZC-L)和磺化-十二醇-甲基丙烯酰甘油-丁二酸酯钠盐(ZD-L).着重研究了ZC-L的结构、表面张力行为、均聚及共聚能力.实验结果表明,不同Surfmer用量以及不同固含量下,MMA/BA/Surfmer,MMA/Surfmer及BA/Surfmer共聚乳液的表面张力较高,说明Surfmer已通过共聚结合在乳胶粒上,乳液中残留甚少.对MMA/BA体系,ZC-L的共聚性能比ZD-L好.     

HIGH SOLIDS-CONTENT NANOSIZE POLYMER LATEXES MADE BY A MODIFIED EMULSION COPOLYMERIZATION

1.INTRODUCTIONSince1980,agreatdealofresearchinteresthasbeendevotedtomicroemulsionpolymerization[1~10].Amicroemulsionmaybedefinedasthermodynamicallystableandopticallytransparentdispersioncomposedbywater,oilandsurfactant;inmanycasesacosurfactantisrequired.Microemulsionpolymerizationprocesscanyieldstablepolymerlatexeswithparticlesizeofabout10nmto100nm.However,therearetwomajordrawbacks,whichhavelimitedtheapplicationsofmicroemulsionpolymerization:(1)highsurfactantconcentration(upto20wt.%ofthet…     

Preparation of MMA－BA－DMAEMA Nanosized Latex

The terpolymer latex of methyl methacrylate (MMA)/butyl acrylate (BA)/ dimethyl aminoethyl methacrylate (DMAEMA) with diameter of less than 100 nm was prepared by seeding semi-continuous emulsion copolymerization using APS (ammonium pcrsulfate) / TMEDA (N,N,N,N-tetramethylethylenediamine) as the redox initiators and SDS (sodium dodecylsulfate) and OP (P-octylpolyethylene glycol phenylether) as co-emulsifiers. The factors that influenced the process stability of the copolymerization and the particle size of the latex were investigated. The addition of aqueous ammonia as coagulation inhibitor provided better process stability of the copoly- merization. The addition of acetic acid as the acidification agent caused a remarkable reduction of the latex particle size.     

HIGH SOLIDS-CONTENT NANOSIZE POLYMER LATEXES MADE BY A MODIFIED EMULSION COPOLYMERIZATION

Polymer nanoparticles were prepared in the methyl methacrylate (MMA)/buty lmethacrylate (BA) emulsion copolymerization process by a modified microemulsion copolymerization method. 2-Hydroxyethyl methacrylate(HEMA), acrylate (AA) and methyl acrylate (MAA) were used as reactive cosurfactants. With this process high polymer: surfactant weight ratios (40:1 or greater),relatively concentrated (～30wt. %) latexes and small (～60nm) particle diameters were obtained.Properties of the latexes were characterized by TEM, DSC, dynamic light scattering, and IR spectroscopy.     

表面活性单体存在下的MMA/BA乳液共聚合(Ⅱ)聚合动力学及机理

研究了表面活性单体[磺化-十二醇-烯丙基甘油-丁二酸酯钠盐(ZC-L)]的用量对MMA/BA/ZC-L乳液聚合速率和粒径的影响,用CoulterLS230型激光粒径分析仪测定聚合过程中乳液的粒径和粒径分布变化,并与MMA/BA无皂乳液聚合及十二烷基苯磺酸钠存在下的MMA/BA乳液聚合作了比较.[ZC-L]CMC时,成核机理包括均相成核和胶束成核机理,生成的粒子因吸收体系中的表面活性单体而稳定存在.     

表面活性单体存在下的MMA／BA乳液共聚合（Ⅱ）：聚合动力？…

研究了表面活性单体「磺化－十二醇－烯丙基甘油－丁二酸酯钠盐（ＺＣ－Ｌ）」的用量对ＭＭＡ／ＢＡ／ＺＣ－Ｌ乳液聚合速率和粒径的影响,用Ｃｏｒｌｔｉｒ ＬＳ２３０型激光粒径分析仪测定聚合过程中乳液的粒径和粒径分布变化,并与ＭＭＡ／ＢＡ无皂乳液聚合及十二烷基苯磺酸钠存在下的ＭＭＡ／ＢＡ乳液聚合作了比较。「ＺＣ－Ｌ」〈ＣＭＣ时,成核机理为均相成核机理,乳胶粒需依靠粒子间的凝聚来提高表面电荷密度而稳定;「ＺＣ     

含氨基、羟基丙烯酸乳液聚合的稳定性

采用间歇及半连续乳液聚合方式,以过硫酸铵/亚硫酸钠为引发体系,合成了甲基丙烯酸甲酯/丙烯酸丁酯/甲基丙烯酸羟乙酯/甲基丙烯酸二氨基乙酯四元共聚物胶乳.系统研究了乳化剂种类和浓度、聚合温度、乳化单体进料方式及进料速率对聚合过程稳定性的影响.聚合温度降低,乳化单体进料速度减慢有利于聚合过程的稳定,采用种子半连续聚合方式比间歇聚合过程更稳定,乳化剂浓度的增加有利于聚合稳定性的提高和乳胶粒子的均匀化.     

无皂阳离子MMA/HEMA胶乳粒子的制备及表征

讨论了微波辐照下带正电荷的自由基引发剂偶氮二异丁基脒盐酸盐(AIBA)引发甲基丙烯酸甲酯(MMA)和甲基丙烯酸2-羟乙酯(HEMA)共聚,用透射电子显微镜、红外光谱仪、差热分析仪等对聚合产物进行表征.结果表明: 两种单体发生了共聚反应,制得均分散、表面洁净的无皂阳离子胶乳粒子;粒子的粒径随着单体HEMA浓度的增加先减小后增加.在微波辐照下共聚反应的速率非常快,几乎所有的反应在20 min之内就能完成.随着单体HEMA浓度的增加,乳液抗电解质稳定性提高.     

STABILITY OF EMULSIFIER-FREE EMULSION COPOLYMERIZATION OF METHYL METHACRYLATE/BUTYL ACRYLATE/SODIUM MONO(ETHYL POLYOXYETHYLENE)MALEATE

A series of new water-soluble bifunctional comonomers having both carboxyl and alkylpolyoxyethylene groups, such as sodium mono(ethyl polyoxyethylene) maleate (ZE series) with variousmolecular weights of polyoxyethylene ethyl ether, were synthesized and characterized. The effects of thestructural factor, the amount and feeding mode of the comonomers, the initiator concentration andpolymerization temperature on the stability of emulsifier-free emulsion copolymerization of methylmethacrylate (MMA) and butyl acrylate (BA) in the presence of a small amount of ZE with potassiumpersulfate as initiator were investigated. Stable, almost monodispersed MMA/BA/ZE emulsifier-free latexparticles were prepared.     

丙烯酸酯纳米乳液的制备与表征

将甲基丙烯酸羟乙酯(HEMA)与甲基丙烯酸(MAA)或丙烯酸(AA)用作甲基丙烯酸甲酯(MMA)／丙烯酸丁酯(BA)乳液聚合体系的反应性助乳化剂，采用一种改进的微乳液聚合方法，合成了高单体／乳化剂比例(大于40：1)的聚丙烯酸酯纳米乳液．讨论了引发剂、乳化剂、助乳化别对乳胶粒大小和胶膜吸水率的影响，并对乳液的流体力学行为，共聚物的拉伸行为及耐水性等进行了研究．     

DESIGN AND CONTROL OF SOAP-FREE HYDROPHILIC-HYDROPHOBIC CORE-SHELL LATEX PARTICLES WITH HIGH CARBOXYL CONTENT IN THE CORE OF THE PARTICLES

Soap-free hydrophilic-hydrophobic core-shell latex particles with high carboxyl content in the core of the particles were synthesized via the seeded emulsion polymerization using methyl methacrylate(MMA),butyl acrylate(BA), methacrylic acid(MAA),styrene(St)and ethylene glycol dimethacrylate(EGDMA)as monomers,and the influences of MMA content used in the core preparation on polymerization,particle size and morphology were investigated by transmission electron microscopy,dynamic light scattering and conductometric titration.The results showed that the seeded emulsion polymerization could be carried out smoothly using "starved monomer feeding process" when MAA content in the core preparation was equal to or less than 24 wt%,and the encapsulating efficiency of the hydrophilic P(MMA-BA-MAAEGDMA) core with the hydrophobic PSt shell decreased with the increase in MAA content.When an interlayer of P(MMAMAA -St)with moderate polarity was inserted between the P(MMA-BA-MAA-EGDMA)core and the PSt shell,well designed soap-free hydrophilic-hydrophobic core-shell latex particles with 24 wt%MAA content in the core preparation were obtained.     

Emulsion copolymerization of fluorinated acrylate in the presence of a polymerizable emulsifier

An emulsifier-free fluorinated polyarcylate emulsion was synthesized by a seed emulsion polymerization method from methyl methacrylate (MMA), butyl acrylate (BA) and hexafluorobutyl methacrylate (HFMA) in the presence of a polymerizable emulsifier—ammonium allyloxtmethylate nonylphenol ethoxylates sulfate (DNS-86). Influences of the DNS-86 level on electrolyte stability of the emulsifier-free emulsion were discussed. In addition, the emulsion and the films were characterized by Fourier transformed infrared (FT-IR) spectrometry, nuclear magnetic resonance (¹H NMR) spectrometry, transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), differential scanning calorimetry (DSC), thermogravimetry (TG), and contact angle (CA) analysis, respectively. The FT-IR spectra and ¹H NMR spectrum showed that HFMA was effectively involved in the emulsion copolymerization and monomers formed the fluorine-containing acrylate copolymer. The resulted emulsion particles had a core–shell structure and a narrow particle size distribution. XPS and CA analysis revealed that a gradient concentration of fluorine existed along the depth profile of the fluorine-containing emulsion film. One side of the film was richer in fluorine and more hydrophobic than the other side. The film formed from the fluorine-containing emulsion showed higher thermal stability than that of the fluorine-free emulsion.