Sol-gel Synthesis and Electrochemical Performance of Li4-xMgxTi5-xZrxO12 Anode Material for Lithium-ion Batteries

The anode materials Li_4?xMg_xTi_5?xZr_xO₁₂ (x=0, 0.05, 0.1) were successfully synthesized by sol‐gel method using Ti(OC₄H₉)₄, CH₃COOLi·2H₂O, MgCl₂·6H₂O and Zr(NO₃)₃·6H₂O as raw materials. The crystalline structure, morphology and electrochemical properties of the as‐prepared materials were characterized by XRD, SEM, cyclic voltammograms (CV), electrochemical impedance spectroscopy (EIS) and charge‐discharge cycling tests. The results show that the lattice parameters of the Mg‐Zr doped samples are slightly larger than that of the pure Li₄Ti₅O₁₂, and Mg‐Zr doping does not change the basic Li₄Ti₅O₁₂ structure. The rate capability of Li_4?xMg_xTi_5?xZr_xO₁₂ (x=0.05, 0.1) electrodes is significantly improved due to the expansile Li⁺ diffusion channel and reduced charge transfer resistance. In this study, Li_3.95Mg_0.05Ti_4.95Zr_0.05O₁₂ represented a relatively good rate capability and cycling stability, after 400 cycles at 10 C, the discharge capacity retained as 134.74 mAh·g^?1 with capacity retention close to 100%. The excellent rate capability and good cycling performance make Li_3.95Mg_0.05Ti_4.95Zr_0.05O₁₂ a promising anode material in lithium‐ion batteries.     

The synergic effects of Ca and Sm co-doping on the crystal structure and electrochemical performances of Li4-xCaxTi5-xSmxO12 anode material

Li₄Ti₅O₁₂ as the well-known “zero strain” anode material for lithium ion batteries (LIBs) suffers from low intrinsic ionic and electronic conductivity. The strategy of lattice doping has been widely taken to relieve the intrinsic issues. But the roles of the dopants are poorly understood. Herein, we propose to modulate the crystal structure and improve the electrochemical performance of Li₄Ti₅O₁₂ by substituting Li and Ti with Ca and Sm, respectively. The roles of Ca and Sm on the crystal structure and electrochemical performances have been comprehensively investigated by means of X-ray diffraction (XRD), neutron diffraction (ND) and electrochemical analysis. The Rietveld refinement of ND data indicate that Ca and Sm prefer to take 8a site (tetrahedral site) and 16d site (octahedral site), respectively. Li_3.98Ca_0.02Ti_4.98Sm_0.02O₁₂ has the longer Li1-O bond and shorter Ti-O bond length which reduces Li⁺ migration barrier as well as enhances the structure stability. Ca-Sm co-doping also alleviates the electrode polarization and enhances the reversibility of oxidation and reduction. In compared to bare Li₄Ti₅O₁₂ and Li_3.95Ca_0.05Ti_4.95Sm_0.05O₁₂, Li_3.98Ca_0.02Ti_4.98Sm_0.02O₁₂ electrode shows the lower charge transfer resistance, higher Li⁺ diffusion coefficient, better rate capability and cycling performance. The proposed insights on the roles of dopants are also instructive to design high performance electrode materials by lattice doping.     

Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

Li4Ti5O12 Anode: Structural Design from Material to Electrode and the Construction of Energy Storage Devices

Spinel Li₄Ti₅O₁₂, known as a zero‐strain material, is capable to be a competent anode material for promising applications in state‐of‐art electrochemical energy storage devices (EESDs). Compared with commercial graphite, spinel Li₄Ti₅O₁₂ offers a high operating potential of ∼1.55 V vs Li/Li⁺, negligible volume expansion during Li⁺ intercalation process and excellent thermal stability, leading to high safety and favorable cyclability. Despite the merits of Li₄Ti₅O₁₂ been presented, there still remains the issue of Li₄Ti₅O₁₂ suffering from poor electronic conductivity, manifesting disadvantageous rate performance. Typically, a material modification process of Li₄Ti₅O₁₂ will be proposed to overcome such an issue. However, the previous reports have made few investigations and achievements to analyze the subsequent processes after a material modification process. In this review, we attempt to put considerable interest in complete device design and assembly process with its material structure design (or modification process), electrode structure design and device construction design. Moreover, we have systematically concluded a series of representative design schemes, which can be divided into three major categories involving: (1) nanostructures design, conductive material coating process and doping process on material level; (2) self‐supporting or flexible electrode structure design on electrode level; (3) rational assembling of lithium ion full cell or lithium ion capacitor on device level. We believe that these rational designs can give an advanced performance for Li₄Ti₅O₁₂‐based energy storage device and deliver a deep inspiration.     

Ab initio Studies on Li4+xTi5O12 Compounds as Anode Materials for Lithium‐Ion Batteries

The structural and electronic properties of Li_4+xTi₅O₁₂ compounds (with 0≤x≤6)—to be used as anode materials for lithium‐ion batteries—are studied by means of first principles calculations. The results suggest that Li₄Ti₅O₁₂ can be lithiated to the state Li_8.5Ti₅O₁₂, which provides a theoretical capacity that is about 1.5 times higher than that of the compound lithiated to Li₇Ti₅O₁₂. Further insertion of lithium species into the Li_8.5Ti₅O₁₂ lattice results in a clear structural distortion. The small lattice expansion observed upon lithium insertion (about 0.4 % for the lithiated material Li_8.5Ti₅O₁₂) and the retained [Li₁Ti₅]^16dO₁₂ framework indicate that the insertion/extraction process is reversible. Furthermore, the predicted intercalation potentials are 1.48 and 0.05 V (vs Li/Li⁺) for the Li₄Ti₅O₁₂/Li₇Ti₅O₁₂ and Li₇Ti₅O₁₂/Li_8.5Ti₅O₁₂ composition ranges, respectively. Electronic‐structure analysis shows that the lithiated states Li_4+xTi₅O₁₂ are metallic, which is indicative of good electronic‐conduction properties.     

Molecular Design Strategy for Ordered Mesoporous Stoichiometric Metal Oxide

A molecular design strategy is used to construct ordered mesoporous Ti³⁺‐doped Li₄Ti₅O₁₂ nanocrystal frameworks (OM‐Ti³⁺‐Li₄Ti₅O₁₂) by the stoichiometric cationic coordination assembly process. Ti⁴⁺/Li⁺‐citrate chelate is designed as a new molecular precursor, in which the citrate can not only stoichiometrically coordinate Ti⁴⁺ with Li⁺ homogeneously at the atomic scale, but also interact strongly with the PEO segments in the Pluronic F127. These features make the co‐assembly and crystallization process more controllable, thus benefiting for the formation of the ordered mesostructures. The resultant OM‐Ti³⁺‐Li₄Ti₅O₁₂ shows excellent rate (143 mAh g^?1 at 30 C) and cycling performances (<0.005 % fading per cycle). This work could open a facile avenue to constructing stoichiometric ordered mesoporous oxides or minerals with highly crystalline frameworks.     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

Li ion diffusion in Li4Ti5O12 thin film electrode prepared by PVP sol-gel method

Li₄Ti₅O₁₂ thin films for rechargeable lithium batteries were prepared by a sol-gel method with poly(vinylpyrrolidone). Interfacial properties of lithium insertion into Li₄Ti₅O₁₂ thin film were examined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and potentiostatic intermittent titration technique (PITT). Redox peaks in CV were very sharp even at a fast scan rate of 50 mV s⁻¹, indicating that Li₄Ti₅O₁₂ thin film had a fast electrochemical response, and that an apparent chemical diffusion coefficient of Li⁺ ion was estimated to be 6.8×10⁻¹¹ cm² s⁻¹ from a dependence of peak current on sweep rates. From EIS, it can be seen that Li⁺ ions become more mobile at 1.55 V vs. Li/Li⁺, corresponding to a two-phase region, and the chemical diffusion coefficients of Li⁺ ion ranged from 10⁻¹⁰ to 10⁻¹² cm² s⁻¹ at various potentials. The chemical diffusion coefficients of Li⁺ ion in Li₄Ti₅O₁₂ were also estimated from PITT. They were in a range of 10⁻¹¹-10⁻¹² cm² s⁻¹.     

Synthesis of single-crystal magnesium-doped spinel lithium manganate and its applications for lithium-ion batteries

Single-crystal magnesium-doped spinel lithium manganate cathode materials are prepared by the hydrothermal method followed by the heat treatment. XRD patterns reveal that Mg²⁺ions have already diffused into the Li_1.088Mn_1.912O₄ crystal structure and not affect the Fd3m space group. SEM images demonstrate that the magnesium-doped spinel lithium manganates show uniform polyhedral single crystals with 2–4 μm. Electrochemical performance demonstrates that the optimized composition of Li_1.088Mg_0.070Mn_1.842O₄ electrode exhibits the best electrochemical properties. It delivers 92.0 mAh g^?1 at 8C rates and corresponds to 90.8% capacity retention (vs. 1C), far higher than those of the pristine electrode (70.4 mAh g^?1 and 69.2%). In addition, the Li_1.088Mg_0.070Mn_1.842O₄ electrode also shows 95.5% capacity retention after 100 cycles at 1C, while the pristine electrode only shows 91.0% capacity retention. The excellent electrochemical performances of Li_1.088Mg_0.070Mn_1.842O₄ electrode are ascribed to the suppressed polarization, more stable crystal structure, and better kinetic characteristics.     

Sol–gel preparation and electrochemical properties of La-doped Li4Ti5O12 anode material for lithium-ion battery

A sol–gel method using Ti(OC₄H₉)₄, LiCH₃COO·2H₂O, and La(NO₃)₃·6H₂O as starting materials and ethyl acetoacetate as chelating agent to prepare pure and lanthanum (La)-doped Li₄Ti₅O₁₂ is reported. The structure and morphology of the active materials characterized by powder X-ray diffraction and scanning electron microscopy analysis indicate that doping with a certain amount of La³⁺ does not affect the structure of Li₄Ti₅O₁₂, but can restrain the agglomeration of the particles during heat treatment. The electrochemical properties measured by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge–discharge cycling tests show that La-doped Li₄Ti₅O₁₂ presents a much improved electrochemical performance due to a decrease in charge transfer resistance. At current densities of 1 and 5 C, the La-doped Li₄Ti₅O₁₂ exhibits excellent reversible capacities of 156.16 and 150.79 mAh?g^?1, respectively. The excellent rate capability and good cycling performance make La-doped Li₄Ti₅O₁₂ a promising anode material for lithium-ion batteries in energy storage systems.     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Doping-induced memory effect in Li-ion batteries: the case of Al-doped Li4Ti5O12

In Li-ion batteries (LIBs), a memory effect has been revealed in two-phase electrode materials such as olivine LiFePO₄ and anatase TiO₂, which complicates the two-phase transition and influences the estimation of the state of charge. Practical electrode materials are usually optimized by the element doping strategy, however, its impact on the memory effect has not been reported yet. Here we firstly present the doping-induced memory effect in LIBs. Pristine Li₄Ti₅O₁₂ is free from the memory effect, while a distinct memory effect could be induced by Al-doping. After being discharged to a lower cutoff potential, Al-doped Li₄Ti₅O₁₂ exhibits poorer electrochemical kinetics, delivering a larger overpotential during the charging process. This dependence of the overpotential on the discharging cutoff leads to the memory effect in Al-doped Li₄Ti₅O₁₂. Our discovery emphasizes the impact of element doping on the memory effect of electrode materials, and thus has implications for battery design.     

Mesoporous Spherical Li4Ti5O12 as High‐Performance Anodes for Lithium‐Ion Batteries

Porous microspherical Li₄Ti₅O₁₂ aggregates (LTO‐PSA) can be successfully prepared by using porous spherical TiO₂ as a titanium source and lithium acetate as a lithium source followed by calcinations. The synthesized LTO‐PSA possess outstanding morphology, with nanosized, porous, and spherical distributions, that allow good electrochemical performances, including high reversible capacity, good cycling stability, and impressive rate capacity, to be achieved. The specific capacity of the LTO‐PSA at 30 C is as high as 141 mA h g^?1, whereas that of normal Li₄Ti₅O₁₂ powders prepared by a sol–gel method can only achieve 100 mA h g^?1. This improved rate performance can be ascribed to small Li₄Ti₅O₁₂ nanocrystallites, a three‐dimensional mesoporous structure, and enhanced ionic conductivity.     

Lithium‐Rich Layered Oxide Li1.18Ni0.15Co0.15Mn0.52O2 as the Cathode Material for Hybrid Sodium‐Ion Batteries

Li‐rich layered oxide Li_1.18Ni_0.15Co_0.15Mn_0.52O₂ (LNCM) is, for the first time, examined as the positive electrode for hybrid sodium‐ion battery and its Na⁺ storage properties are comprehensively studied in terms of galvanostatic charge–discharge curves, cyclic voltammetry and rate capability. LNCM in the proposed sodium‐ion battery demonstrates good rate capability whose discharge capacity reaches about 90 mA h g^?1 at 10 C rate and excellent cycle stability with specific capacity of about 105 mA h g^?1 for 200 cycles at 5 C rate. Moreover, ex situ ICP‐OES suggests interesting mixed‐ions migration processes: In the initial two cycles, only Li⁺ can intercalate into the LNCM cathode, whereas both Li⁺ and Na⁺ work together as the electrochemical cycles increase. Also the structural evolution of LNCM is examined in terms of ex situ XRD pattern at the end of various charge–discharge scans. The strong insight obtained from this study could be beneficial to the design of new layered cathode materials for future rechargeable sodium‐ion batteries.     

Silver(I)‐Selective PVC Membrane Potentiometric Sensor Based on a Recently Synthesized Calix[4]arene

A new PVC membrane potentiometric sensor for Ag(I) ion based on a recently synthesized calix[4]arene compound of 5,11,17,23‐tetra‐tert‐butyl‐25,27‐dihydroxy‐calix[4]arene‐thiacrown‐4 is developed. The electrode exhibits a Nernstian response for Ag(I) ions over a wide concentration range (1.0×10^?2?1.0×10^?6 M) with a slope of 53.8±1.6 mV per decade. It has a relatively fast response time (5–10 s) and can be used for at least 2 months without any considerable divergence in potentials. The proposed electrode shows high selectivity towards Ag⁺ ions over Pb²⁺, Cd²⁺, Co²⁺, Zn²⁺, Cu²⁺, Ni²⁺, Sr²⁺, Mg²⁺, Ca²⁺, Li⁺, K⁺, Na⁺, NH₄⁺ ions and can be used in a pH range of 2–6. Only interference of Hg²⁺ is found. It is successfully used as an indicator electrode in potentiometric titration of a mixture of chloride, bromide and iodide ions.     

Electrospun V2O5 Nanostructures with Controllable Morphology as High‐Performance Cathode Materials for Lithium‐Ion Batteries

Porous V₂O₅ nanotubes, hierarchical V₂O₅ nanofibers, and single‐crystalline V₂O₅ nanobelts were controllably synthesized by using a simple electrospinning technique and subsequent annealing. The mechanism for the formation of these controllable structures was investigated. When tested as the cathode materials in lithium‐ion batteries (LIBs), the as‐formed V₂O₅ nanostructures exhibited a highly reversible capacity, excellent cycling performance, and good rate capacity. In particular, the porous V₂O₅ nanotubes provided short distances for Li⁺‐ion diffusion and large electrode–electrolyte contact areas for high Li⁺‐ion flux across the interface; Moreover, these nanotubes delivered a high power density of 40.2 kW kg^?1 whilst the energy density remained as high as 201 W h kg^?1, which, as one of the highest values measured on V₂O₅‐based cathode materials, could bridge the performance gap between batteries and supercapacitors. Moreover, to the best of our knowledge, this is the first preparation of single‐crystalline V₂O₅ nanobelts by using electrospinning techniques. Interestingly, the beneficial crystal orientation provided improved cycling stability for lithium intercalation. These results demonstrate that further improvement or optimization of electrochemical performance in transition‐metal‐oxide‐based electrode materials could be realized by the design of 1D nanostructures with unique morphologies.     

Electochemical characteristics of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>/Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> battery with conducting polymeric binder

Lithium-ion battery based on LiMn₂O₄/Li₄Ti₅O₁₂ materials was assembled for the first time. The cathode and anode of this battery are prepared with the aqueous combined binder poly-3,4-ethylenedioxythiophene: polystyrene sulfonate/carboxymethylcellulose (without polyvinylidene fluoride). The capacity of the LiMn₂O₄/Li₄Ti₅O₁₂ battery was found to be 75 mA h g^–1 at 0.1 C and 55 mA h g^–1 at 1 C. A 95% capacity was retained after 100 charge-discharge cycles. The batteries demonstrated a high Coulombic efficiency close to 100%. Scanning electron microscopy demonstrated that using the conducting binder poly-3,4-ethylenedioxythiophene: polystyrene sulfonate/carboxymethylcellulose provides formation of dense compact layers of electrode materials with good adhesion to the substrate. The electrode structure remains maintained after 100 charge-discharge cycles.     

Synthesis and electrochemical properties of Ca-doped LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material for lithium ion battery

LiNi_0.8Co_0.2O₂ and Ca-doped LiNi_0.8Co_0.2O₂ cathode materials have been synthesized via a rheological phase reaction method. X-ray diffraction studies show that the Ca-doped material, and also the discharged electrode, maintains a hexagonal structure even when cycled in the range of 3.0–4.35 V (vs Li⁺/Li) after 100 cycles. Electrochemical tests show that Ca doping significantly improves the reversible capacity and cyclability. The improvement is attributed to the formation of defects caused by the partial occupancy of Ca²⁺ ions in lithium lattice sites, which reduce the resistance and thus improve the electrochemical properties.     

Synthesis and electrochemical performances of Li4Ti4.95Zr0.05O12/C as anode material for lithium-ion batteries

Spinel Li₄Ti_5 − x Zr _x O₁₂/C (x = 0, 0.05) were prepared by a solution method. The structure and morphology of the as-prepared samples were characterized by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. The electrochemical performances including charge–discharge (0–2.5 V and 1–2.5 V), cyclic voltammetry, and ac impedance were also investigated. The results revealed that the Li₄Ti_4.95Zr_0.05O₁₂/C had a relatively smaller particle size and more regular morphology than that of Li₄Ti₅O₁₂/C. Zr⁴⁺ doping enhanced the ability of lithium-ion diffusion in the electrode. It delivered a discharge capacity 289.03 mAh g⁻¹ after 50 cycles for the Zr⁴⁺-doped Li₄Ti₅O₁₂/C while it decreased to 264.03 mAh g⁻¹ for the Li₄Ti₅O₁₂/C at the 0.2C discharge to 0 V. Zr⁴⁺ doping did not change the electrochemical process, instead enhanced the electronic conductivity and ionic conductivity. The reversible capacity and cycling performance were effectively improved especially when it was discharged to 0 V.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.