疏水改性聚丙烯酰胺对原油组分界面扩张流变性质的影响

利用悬挂滴方法研究了疏水改性聚丙烯酰胺(HMPAM)对胜利采油厂高温高盐油藏采出原油中酸性活性组分和沥青质界面膜扩张流变性质的影响,考察了不同活性组分浓度条件下的界面扩张流变行为.实验结果表明:1750mg·L-1HMPAM能够在界面上形成网络结构,界面扩张模量数值高达100mN·m-1左右;油相中的酸性组分随着老化时间增加吸附到界面上,与HMPAM分子的疏水改性部分形成聚集结构,一方面通过快速的扩散交换过程大大降低扩张模量,另一方面通过与疏水改性部分的相互作用加强HMPAM分子间的缔合强度,增强网络结构的弹性.沥青质分子尺寸相对较大,分子间存在氢键等较强的相互作用,造成沥青质界面聚集体和HMPAM形成的网络结构共同决定界面膜性质,混合膜的扩张模量较单独HMPAM体系仅略有降低.     

聚醚类破乳剂的界面扩张流变性质

采用悬挂滴方法研究了不同结构聚醚类破乳剂与煤油间的界面张力及界面扩张流变性质. 结果表明, 4种聚醚类破乳剂均具有较强的降低界面张力能力, 且支链化程度越低分子在界面上排列越紧密, 直线型破乳剂在低浓度条件下界面张力最低. 破乳剂的分子尺寸较大, 慢弛豫过程控制界面膜性质, 吸附膜以弹性为主. 同时, 柔性聚氧乙烯链和聚氧丙烯链对界面膜性质的影响较大, 随着支链化程度增大, 界面分子间相互作用增强, 界面膜弹性增强, 黏性降低.     

聚表剂驱模拟采出液油水界面性能研究

通过考察聚表剂对大庆油田聚表剂驱模拟采出液油水界面张力、油水界面扩散双电层zeta电位、界面粘弹性以及界面膜强度的影响,研究聚表剂对聚表剂驱模拟采出液油水界面性能的影响规律。结果表明:具有表面活性剂和聚合物双重性能的聚表剂利用其两亲性质在油水界面吸附,形成稳定的界面膜,使油水界面张力降低,界面膜强度增加;且随聚表剂浓度增加,油水界面张力降低,界面膜强度增加。在所研究的四种聚表剂类型中,海博Ⅲ(O/W)型聚表剂改善油水界面性能的效果较为突出。     

聚丙烯酰胺对烷基苯磺酸盐界面吸附膜扩张流变性质的影响

采用小幅低频振荡和界面张力弛豫技术, 研究了部分水解聚丙烯酰胺(Mo-4000)和阴离子表面活性剂2-丙基-4,5-二庚基苯磺酸钠(377)体系在癸烷/水界面上的扩张黏弹性质, 并考察了电解质对体系界面流变性质的影响. 研究结果发现, 低表面活性剂浓度时, 聚合物的加入大大降低了扩张模量; 而高表面活性剂浓度时, 聚合物的存在导致了界面膜更接近弹性膜. 一方面电解质压缩双电层, 增加界面膜的紧密程度, 造成高频条件下扩张模量增大; 另一方面, 电解质增强表面活性剂分子在界面与体相间的扩散交换作用, 增大了扩张模量的频率依赖性, 造成低频条件下扩张模量降低.     

破乳剂对油水界面膜作用机理研究

研究了破乳剂存在下油膜寿命、油膜薄化速率以及油水界面性质与破乳效果的关系.结果表明,破乳剂使油水界面弹性降低,导致油水界面强度减弱,界面膜寿命变短,界面膜厚度变薄.当膜厚度变薄到一临界值时,膜破裂,导致破乳脱水.同种破乳剂,随着其浓度的增加,界面弹性降低.当浓度超过某一值时,界面弹性值基本不变.不同种破乳剂,界面弹性降低幅度越大,其破乳效果越好.界面弹性值可以很好解释破乳剂的脱水率变化规律.     

固体粒子稳定的乳状液研究进展

综述了固体粒子对乳状液稳定性影响的有关研究进展。微细不溶的固体粒子构成重要的一类乳化剂,被水相和油相部分润湿的固体粒子能够有效地稳定乳状液。固体粒子稳定乳状液的效果取决于以下因素:粒子大小、粒子间相互作用和粒子的润湿性质。固体粒子存在的油-水界面表现出粘弹行为,这种粘弹界面膜可大大地提高空间位阻,减缓乳状液液珠间液膜变薄的速率,从而提高乳状液地稳定性。原油中的粘土、胶质、沥青质和石蜡等胶体粒子被证明对乳状液的稳定性起很大的作用。     

电导法研究树脂与游离酸的相互作用

利用电导实验技术跟踪树脂吸附游离酸的行为 ,讨论了外加盐和乙醇等因素对吸附的影响 ,利用固 -液相互作用方程求取吸附剂 -吸附质相互作用能。实验结果表明 ,树脂吸附游离酸 ,其表观吸附速率常数随着外加盐离子浓度的增大而减少 ;表观吸附速率常数与吸附剂 -吸附质相互作用能存在线性关系。     

界面张力弛豫法研究不同分子量原油活性组分界面扩张粘弹性

采用界面张力弛豫法研究了不同分子量原油活性组分在正癸烷-水界面上的扩张粘弹性质,阐述了界面扩张模量的弹性和粘性随扩张频率的变化规律.研究发现,随着原油活性组分分子量的增大,极限扩张粘度明显增大,而极限扩张弹性逐渐增大;当分子量大于某一数值后,极限扩张弹性变化不明显.对界面张力弛豫实验结果进行拟合得到的参数表明,界面上和界面附近的微观弛豫过程的数目随原油活性组分分子量的增加而增加,弛豫过程的特征频率也呈规律性变化.不同原油活性组分的界面扩张粘弹性质可从其不同特征的微观弛豫过程得到解释.     

驱油体系化学剂间相互作用对界面吸附膜的影响

采用界面张力弛豫技术研究了不对称Gemini表面活性剂C12COONa-p-C9SO3Na、部分水解聚丙烯酰胺Mo-4000、疏水缔合水溶性聚丙烯酰胺(HMPAM)等驱油体系化学剂在癸烷/水界面上的扩张流变性质,考察了不同离子强度、不同类型电解质对体系界面流变性质的影响,计算得到界面扩张弹性模量和粘性模量的全频率谱,并通过归一化方法(cole-cole图)探讨了界面吸附膜的弛豫过程。研究发现,界面膜内分子重排和界面与体相间分子扩散交换是影响膜性质的主要弛豫过程。表面活性剂体相浓度增大有利于界面分子重排过程,而低频有利于扩散交换过程;不同结构聚合物以及不同离子强度、不同类型电解质对表面活性剂吸附膜有不同的影响。     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。 结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

Rheology of asphaltene-toluene/water interfaces

The stability of water-in-crude oil emulsions is frequently attributed to a rigid asphaltene film at the water/oil interface. The rheological properties of these films and their relationship to emulsion stability are ill defined. In this study, the interfacial tension, elastic modulus, and viscous modulus were measured using a drop shape analyzer for model oils consisting of asphaltenes dissolved in toluene for concentrations varying from 0.002 to 20 kg/m(3). The effects of oscillation frequency, asphaltene concentration, and interface aging time were examined. The films exhibited viscoelastic behavior. The total modulus increased as the interface aged at all asphaltene concentrations. An attempt was made to model the rheology for the full range of asphaltene concentration. The instantaneous elasticity was modeled with a surface equation of state (SEOS), and the elastic and viscous moduli, with the Lucassen-van den Tempel (LVDT) model. It was found that only the early-time data could be modeled using the SEOS-LVDT approach; that is, the instantaneous, elastic, and viscous moduli of interfaces aged for at most 10 minutes. At longer interface aging times, the SEOS-LVDT approach was invalid, likely because of irreversible adsorption of asphaltenes on the interface and the formation of a network structure.     

Effect of Demulsifier Structures on the Interfacial Dilational Properties of Oil–Water Films

The dilational properties of a branch-shaped polyether-type nonionic demulsifier (PEB), a comb-shaped polyether-type nonionic demulsifier (PEC), and a star-shaped polyether-type nonionic demulsifier (PES) at the decane–water interfaces were investigated by Langmuir trough method through oscillating barrier and interfacial tension relaxation methods, which are mainly in the influences of oscillating frequency and bulk concentration on dilational properties. Meanwhile, the effect of demulsifiers on interfacial dilational modulus of diluted crude oil was also explored. The experimental results indicate that all demulsifiers can decrease the dilational modulus of diluted crude oil at the experimental concentration. The addition of PEB causes the dilational modulus of crude oil to be lower than that at the water–decane interface. The demulsifier PEC has a similar effect with PES to influence the interfacial film of crude oil: at low concentration, the dilational modulus of mixed interfacial film is lower than that of demulsifier alone, while at high concentration, the dilational modulus of mixed interfacial film is slightly higher than that of demulsifier alone. The dependence of static modulus on the bulk concentration is consistent with the trend of interfacial dilational modulus with concentration for demulsifiers PEB, PEC, and PES. The studies about the structure modulus show that the new demulsifiers PEC and PES have a stronger ability than branch-shaped demulsifier PEB to destroy the interfacial film.     

Interfacial dilational rheology properties of films formed at the oil/water interface by reaction between tetrameric acid and calcium ion

This article aims to determine the applicability of interfacial dilational rheology to study the formation of viscoelastic film at the oil/water interface by reaction between tetrameric acids ARN and calcium ions, and to determine the influence of asphaltenes and naphthenic acids (NA) on this film. It was first found that the formation of viscoelastic film by reaction between ARN and calcium ions is easily observed by dilational rheology: Significantly high values of E′ (130?mN/m) were measured for this system at low ARN concentration (10?µM). These values are at least 5 to 10 times higher than values obtained for ARN without Ca²⁺ or other crude oil components such as asphaltenes and naphthenic acids.

The influence of asphaltenes and NA on the viscoelastic film formation has been studied. When asphaltenes or NA are present, the interfacial viscoelastic film is weakened: There is a gradual decrease of E′ and E″ when the asphaltenes or NA concentration increases. These two components can therefore inhibit the ARN/Ca²⁺ film formation. This decrease is similar to the one previously observed by shear rheology. Several explanations are proposed.     

Effect of Molecular Weight on the Interfacial Dilational Viscoelasticity of Anionic Polyelectrolyte/Surfactant Systems

In this article, the effect of molecular weight on the interfacial tension and interfacial dilational viscoelasticity of polystyrene sulfonate/surfactant adsorption films at the water-octane interface have been studied by spinning drop method and oscillating barriers method respectively. The experimental results show that different interfacial behaviors can be observed in different type of polyelectrolyte/surfactant systems. PSS/cationic surfactant CTAB systems show the classical behavior of oppositely charged polyelectrolyte/surfactant systems and can be well explained by electrostatic interaction. Molecular weight of PSS plays a crucial role in the nature of adsorption film. The complex formed by CTAB and higher molecular weight PSS, which has larger dimension and stronger interaction, results in higher dilational modulus at lower surfactant bulk concentration. In the case of PSS/anionic surfactant SDS systems, the co-adsorption of PSS at interface through hydrophobic interaction with alkyl chain of SDS leads to the increase of interfacial tension and the decrease of dilational modulus at lower surfactant bulk concentration. For PSS/nonionic surfactant T × 100 systems, PSS may form a sublayer contiguous to the aqueous phase, which has little effect on interfacial tension but slightly decreases dilational modulus.     

The Fast Relaxation Process between Hydrophobically Modified Associating Polyacrylamide and Different Surfactants at the Water‐Octane Interface

In our previous work (Macromolecules 2004, 37:2930), we found that the hydrophobic blocks of polyacrylamide modified with 2‐phenoxylethyl acrylate (POEA) and anionic surfactant sodium dodecyl sulfate (SDS) may form mixed associations at octane/water interface. However, the process involving the exchange of surfactant molecules between monomers and mixed associations in interface is so fast that we cannot obtain its characteristic time. In this article, the interfacial dilational viscoelastic properties of another hydrophobically associating block copolymer composed of acrylamide (AM) and a low amount of 2‐ethylhexyl acrylate (EHA) (<1.0 mol%) at the octane‐water interfaces were investigated by means of oscillating barriers method and interfacial tension relaxation method respectively. The influences of anionic surfactant SDS and nonionic surfactant Triton X‐100 on the dilational viscoelastic properties of 7000 ppm polymer solutions were studied. The results showed that the interaction between P(AM/2‐EHA) and SDS was similar to that of P(AM/POEA) and SDS. Moreover, we got the relaxation characteristic time of the fast process involving the exchange of s Triton X‐100 molecules between monomers and mixed associations.

We also found that the interfacial tension response of hydrophobically associating water‐soluble copolymers to the sinusoidal oscillation of interfacial area at low bulk concentration is as same as that of the typical surfactants: the interfacial tension decreases with the decrease of interfacial area because of the increase of interfacial active components. However, the interfacial tension increases with the decrease of interfacial area at 7000 ppm P(AM/2‐EHA), which is believed to be correlative with the structure of absorbed film. The results of another hydrophobically associating polymer P(AM/POEA) and polyelectrolyte polystyrene sulfonate (PSS) enhanced our supposition. The phase difference between area oscillation and tension oscillation has also been discussed considering the apparent negative value.     

Influence of Interfacial Rheological Properties on Stability of Asphaltene-Stabilized Emulsions

A series of oscillating droplet measurements have been performed on asphaltenes at the oil/water interface, in order to correlate the interfacial rheological behavior to their ability to stabilize emulsions. In the concentration sweep, the elastic modulus goes through a maximum around an asphaltene concentration of 0.05–0.10 g/l. This behavior was not in good correspondence with emulsion stability, which increased consistently from low to high concentrations. The decrease above 0.10 g/l was most likely an effect of diffusion of asphaltenes in the bulk to the interface, which became more significant at higher bulk concentrations. The rheology data as a function of concentration has been fitted to Butler's surface equation of state and the Lucassen–van den Tempel model. A decent correlation was found between emulsion stability and elasticity for both the effect of solvent aromaticity and pH. The elastic modulus displayed a gradual increase when xylene was mixed with heptane as the solvent, as was seen with emulsion stability. This was not caused by a significant increase of the adsorbed amount of asphaltene at the interface, as shown by a quartz crystal microbalance (QCM), but a more efficient reorganization of the already adsorbed asphaltenes. The ability asphaltenes displayed in stabilizing emulsions was significantly increased at both low and high pH, according to a previous study. The elastic modulus, on the other hand, only showed a very weak increase at pH 2, but a better correlation with emulsion stability above pH 8. From this it would appear that the dissociation of acid groups in the asphaltene structure at high pH has a bigger impact on the interfacial activity than the protonation of bases at low pH, while their effect on emulsion stability was the same.      

Water-in-model oil emulsions studied by small-angle neutron scattering: interfacial film thickness and composition

The ever-increasing worldwide demand for energy has led to the upgrading of heavy crude oil and asphaltene-rich feedstocks becoming viable refining options for the petroleum industry. Traditional problems associated with these feedstocks, particularly stable water-in-petroleum emulsions, are drawing increasing attention. Despite considerable research on the interfacial assembly of asphaltenes, resins, and naphthenic acids, much about the resulting interfacial films is not well understood. Here, we describe the use of small-angle neutron scattering (SANS) to elucidate interfacial film properties from model emulsion systems. Modeling the SANS data with both a polydisperse core/shell form factor as well as a thin sheet approximation, we have deduced the film thickness and the asphaltenic composition within the stabilizing interfacial films of water-in-model oil emulsions prepared in toluene, decalin, and 1-methylnaphthalene. Film thicknesses were found to be 100-110 A with little deviation among the three solvents. By contrast, asphaltene composition in the film varied significantly, with decalin leading to the most asphaltene-rich films (30% by volume of the film), while emulsions made in toluene and methylnaphthalene resulted in lower asphaltenic contents (12-15%). Through centrifugation and dilatational rheology, we found that trends of decreasing water resolution (i.e., increasing emulsion stability) and increasing long-time dilatational elasticity corresponded with increasing asphaltene composition in the film. In addition to the asphaltenic composition of the films, here we also deduce the film solvent and water content. Our analyses indicate that 1:1 (O/W) emulsions prepared with 3% (w/w) asphaltenes in toluene and 1 wt % NaCl aqueous solutions at pH 7 and pH 10 resulted in 80-90 A thick films, interfacial areas around 2600-3100 cm (2)/mL, and films that were roughly 25% (v/v) asphaltenic, 60-70% toluene, and 8-12% water. The increased asphaltene and water film composition at pH 10 versus pH 7, along with unique dynamic interfacial tension profiles, suggested that the protonation state of carboxylic moieties within asphaltenes impacts the final film properties. This was further supported when we characterized similar asphaltenic emulsions that also contained 9-anthracence carboxylic acid (ACA). Addition of this aromatic acid led to slightly thinner films (70-80 A) that were characteristically more aqueous (up to 20% by volume) and 5-6% (v/v) ACA. This unique in situ characterization (deduced entirely from SANS data from emulsion samples) of the entire film composition calls for further investigation regarding the role this film-based water plays in emulsion stability.     

Characterization of C80 Naphthenic Acid and Its Calcium Naphthenate

A C80 naphthenic acid (tetraacid) and its calcium naphthenate have been characterized with respect to their interfacial properties at both the oil/water and the air/water interfaces as well as their thermal properties. Naphthenic acids in crude oils may give rise to different problems in oil production including naphthenate deposition and formation of stable emulsions. This may lead to severe disturbances of regularity and shut‐in in the oil production. The interfacial activity and film properties of the compounds were examined by the oscillating drop method. The calcium naphthenate film was primarily elastic and solid‐like. Measurements on the acid gave similar results, an elastic, solid‐like film was formed, but the effect was less pronounced than for the calcium naphthenate. Langmuir‐Blodgett films of the acid and its naphthenate were deposited on conducting substrates and subsequently analyzed by scanning electron microscopy, SEM. It was found that the pure acid formed crystalline structures in the interfacial film on compression. The calcium naphthenate, on the other hand, form a continuous amorphous film on the substrate.     

A buckling mechanics approach to elastic modulus determination of glassy polymer films

Column buckling mechanics were examined as a technique to determine the modulus of glassy polymer films that fail at very low strains in tension. As an alternative modulus measurement technique, free‐standing column buckling (FSCB) mechanics were investigated here. Given the film geometries and the critical buckling load, classical relationships can be used to determine the modulus. Several polymeric materials were tested and compared to uniaxial tensile values to determine the robustness and validity of the technique. Film geometries were varied from 4 to 18 mm in width and from 15 to 60 mm in length. The films were compressed in plane until buckling occurred and the critical buckling load was measured for each geometry. The critical buckling load increased as film width increased and decreased as film length increased, while the thickness was held constant for each material. For polyethylene terephthalate films, the elastic modulus was determined to be 3.06 ± 0.58 GPa. This FSCB‐determined modulus was compared to the elastic modulus obtained by tensile testing (3.54 ± 0.2 GPa). The modulus measurement technique presented here has the potential to be used experimentally to determine the elastic modulus of glassy polymer films that perform poorly in tension. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 15–20