非比例循环塑性内时本构关系研究

在Valanis的内时本构理论的框架中,引入内结构张量以反映由于非比例加载而引起金属材料的附加等向强化及异向强化效应,同时提出材料强化程度的度量采用沿路径法线方向的塑性应变分量来描述.这些考虑的有效性已经通过用所建模型对304不锈钢材料在一些典型非比例循环加载路径下的响应进行的理论预测得到了验证;将该模型应用于U71Mn材料室温单轴棘轮行为描述中,结果显示内结构张量的引入不仅能较好地反映应变控制下的非比例附加效应,而且也能较好地反映应力控制下塑性应变的累积及变化率.     

Cyclic stress-strain behaviour of alloy AA6060, part I: Uniaxial experiments and modelling

An experimental and numerical study of the uniaxial cyclic behaviour of the aluminium alloy AA6060 in tempers T4 and T6 is reported. Material characteristics studied through the experimental programme are the monotonic stress-strain curve, the shape of the hysteresis loops, cyclic hardening and softening, mean stress relaxation and memorization of prior strain histories. A model of cyclic plasticity, proposed in the literature, is used to simulate the physical behaviour of the alloy in temper T4. The model utilizes multi-component forms of kinematic and isotropic hardening variables with non-linear evolutionary rules to describe the hysteresis loops and the transient behaviour of the material. The evolution of the Bauschinger effect and the memory of prior strain histories are properly modelled through additional internal variables. Tests and simulations are compared for temper T4, and good agreement is obtained between physical and correlated behaviour.     

Anisotropic strain hardening in polycrystalline copper and aluminium

A new viscoplastic model for the plastic stress-strain behaviour of f.c.c. metals is presented. In this model the strain hardening results from increasing dislocation densities. The observed stagnation of strain hardening after strain reversals is explained by a lowering of the increase in dislocations due to annihilation of dislocations with opposite polarity. The model is applied to Bauschinger and x-y tests on commercial copper and aluminium, and to cyclic tests on copper. The theoretical results are in good agreement with the measurements.     

考虑路径相关性的非比例循环塑性本构模型

根据非比例加载下金属材料响应的延迟特性及加载路径相关性,选取沿应力迹法向的塑性应变的累积量作为非比例加载影响的度量,相应给出反映非比例附加强化的变量,并假设其模量和强化率与加载路径的几何参数相关．为反映由于非比例加载而引起的材料强化的异向效应,在Valanis的塑性内时响应方程中引入与加载路径几何性质有关的应力项,构成非比例循环塑性本构关系．对316和304不锈钢材料在一些典型非比例循环加载路径下的应力响应进行了理论预测,与Benallal等及McDowell的实验结果取得了良好的一致．     

Cyclic stress-strain behaviour of alloy AA6060 T4, part II: Biaxial experiments and modelling

Laboratory tests have been conducted to investigate the inelastic behaviour of aluminium alloy AA6060 T4 subjected to non-proportional cyclic loading. The results of four tests with variable strain path shapes and strain amplitudes are reported in this paper. The tests were carried out by applying combined axial force and torque to thin-walled tubular specimens, using effective strain amplitudes in the range 0.4–0.8%. Major emphasis has been put on the two important material properties: plastic anisotropy and influence of strain range and strain path shapes on cyclic hardening. A constitutive model for cyclic plasticity is used to predict the stress response of the alloy for the non-proportional strain paths applied in the experiments. The model adopts a quadratic yield function and multi-component non-linear isotropic and kinematic hardening rules to describe plastic anisotropy, the shape of the hysteresis loops and the evolution of cyclic hardening. Good agreement is obtained between the physical and correlated stress response of the alloy.     

Effects of crystal content on the mechanical behaviour of polyethylene under finite strains: Experiments and constitutive modelling

The mechanical stress-strain behaviour of polyethylene (PE) materials under finite strains is studied both experimentally and theoretically. In order to gain insight into the structure and physical properties of investigated PE materials, a series of thermal (DSC and DMTA) and microstructural (small-angle X-ray scattering and AFM) characterizations have been undertaken. The influence of crystallinity on the various features of the tensile stress-strain response is considered over a large strain range, implying thermoplastic-like to elastomer-like mechanical behaviour. A physically-based hyperelastic-viscoplastic approach was adopted to develop a pertinent model for describing the mechanical behaviour of PE materials under finite strains. The semicrystalline polymer is being treated as a heterogeneous medium, and the model is based on a two-phase representation of the microstructure. The effective contribution of the crystalline and amorphous phases to the overall intermolecular resistance to deformation is treated in a composite framework, and coupled to a molecular network resistance to stretching and chain orientation capturing the overall strain hardening response. In order to extract the individual constitutive response of crystalline and amorphous phases, a proper identification scheme based on a deterministic approach was elaborated using the tensile test data of PE materials under different strain rates. Comparisons between the constitutive model and experiments show fair agreement over a wide range of crystallinities (from 15% to 72%) and strain rates. The constitutive model is found to successfully capture the important features of the observed monotonic stress-strain response: the thermoplastic-like behaviour for high crystallinity includes a stiff initial response, a yield-like event followed by a gradual increase of strain hardening at very large strains; for the elastomer-like behaviour observed in the low crystallinity material, the strain hardening response is largely predominant. Strain recovery upon unloading increases with decreasing crystallinity: this is quantitatively well reproduced for high crystallinity materials, whereas predictions significantly deviate from experiments at low crystallinity. Model refinements are finally proposed in order to improve the ability of the constitutive equations to predict the nonlinear unloading response whatever the crystal content.     

金属材料的强度与应力-应变关系的球压入测试方法

压入法获取材料单轴应力-应变关系和抗拉强度对服役结构完整性评价有重要的基础意义.假定材料均匀连续、各向同性、应力应变关系符合Hollomon律,基于能量等效假定,即代表性体积单元(representativevolume element, RVE)的vonMises等效和有效变形域内能量中值等效假定,本文提出了关联材料载荷、深度、球压头直径和Hollomon律的四参数半解析球压入(semi-analyticalspherical indentation,SSI)模型.通过球压入载荷-深度试验关系获得材料的应力-应变关系和抗拉强度.考虑压入过程中的损伤效应,针对金属材料提出了用于球压入测试的材料弹性模量修正模型.对11种延性金属材料完成了球压入试验,采用本文提出的球压入试验方法测到的弹性模量、应力-应变关系和抗拉强度与单轴拉伸试验结果吻合良好.      

Cyclic plasticity modeling with the distribution of non-linear relaxations approach

Motivated by the distribution of non-linear relaxation (DNLR) approach, a phenomenological model is proposed in order to describe the cyclic plasticity behavior of metals under proportional and non-proportional loading paths with strain-controlled conditions. Such a model is based on the generalization of the Gibbs's relationship outside the equilibrium of uniform system and the use of the fluctuation theory to analyze the material dissipation due to its internal reorganization. The non-linear cyclic stress–strain behavior of metals notably under complex loading is of particular interest in this study. Since the hardening effects are described appropriately and implicitly by the model, thus, a host of inelastic behavior of metals under uniaxial and multiaxial cyclic loading paths are successfully predicted such as, Bauschinger, strain memory effects as well as additional hardening. After calibrating the model parameters for two metallic materials, the model has demonstrated obviously its ability to describe the cyclic elastic-inelastic behavior of the nickel base alloy Waspaloy and the stainless steel 316L. The model is then implemented in a commercial finite element code simulating the cyclic stress–strain response of a thin-walled tube specimen. The numerical responses are in good agreement with experimental results.     

The implicit standard material theory for modelling the nonassociative behaviour of metals

Summary  Modelling the elastoplastic or elastoviscoplastic behaviour of metallic materials exhibiting strain hardening and damage leads to complex nonassociative constitutive equations, sources of many theoretical and numerical troubles. The usual modelling of a nonassociative constitutive equation leads to the loss of the interesting and very useful properties of generalised standard materials deriving from the key concepts of convexity and normality. The argument that will be developed is that the bipotential concept is an appropriate answer. In the first part, after introducing the state variables generally used to describe the behaviour of metallic materials, the constitutive equations subjected to the principles of thermodynamics are derived from two potentials. The state potential gives the state laws, and the bipotential of dissipation delivers the evolution laws for state variables, through the implicit normality assumption. The second part is devoted to several particular applications to metal elastoplasticity and elastoviscoplasticity models. Received 29 March 2000; accepted for publication 26 September 2000     

Zr基非晶合金JH-2模型的构建及应用

为构建Zr_62.5Nb₃Cu_14.5Ni₁₄Al₆非晶合金在高压、大应变、高应变率状态下的材料模型,采用根据实验数据理论推导和数值模拟对比反馈的方法,对材料的Johnson-Holmquist本构模型（JH-2模型）参数进行了研究:材料的静水压力-体应变关系通过平板冲击实验数据和理论推导得到;无损材料强度与应变、应变率的关系通过轴向压缩实验数据确定;材料损伤参数与破碎材料强度参数的关系通过平板冲击实验数据确定;破碎材料强度参数通过数值模拟与实验结果对比的反馈法得到。将材料模型应用于平板冲击和破片侵彻的数值模拟,通过数值模拟与实验结果对比的方式,验证材料模型的准确性。结果表明,平板冲击实验中,材料的自由面粒子速度曲线与数值模拟结果吻合度较高;破片侵彻实验中,破片对钢靶的侵彻深度、开坑孔径与数值模拟结果的一致性较好,构建的材料模型较准确反映了材料的动态力学特性。     

考虑塑性应变记忆恢复的循环棘轮本构模型研究

在统一粘塑性循环本构理论框架下,以Ohno-Abdel-Karim非线性随动硬化模型为基础,建立了一个循环本构模型。模型通过引入塑性应变幅值记忆效应,并在塑性应变记忆项中加入恢复系数,提高了对循环硬化材料单轴棘轮行为的预言能力。将模型应用于316L不锈钢单轴棘轮行为的描述中,模拟不同平均应力、应力幅值下的棘轮应变,均与实验数据吻合较好,证明本文改进的本构模型能合理地描述循环硬化材料的单轴棘轮行为。     

土的应力-应变关系的一种描述模式

通常将由土的剪切试验测得的应力-应变关系曲线(q～ε1曲线)分为应变硬化型和应变软化型,文中提出了一种能同时描述应变硬化型q～ε1曲线和应变软化型q～ε1曲线的新模式,并导出了统一的切线模量表达式,进一步探讨了该应力-应变关系曲线描述模式在拟合应变硬化型曲线时的简化形式,及简化形式中参数取值方法和参数与围压的关系等方面的问题。通过与邓肯-张模型和应变软化模型的对比,结果表明该应力-应变关系曲线描述模式能更好地与试验数据吻合,且用其简化形式拟合应变硬化型曲线时,可以通过调整其中一个参数值来表达出不同的曲线形式,从而体现出土体应力-应变关系的多样性。该应力-应变关系描述模式为发展更一般的非线性弹性模型提供了一定的理论基础。     

Constitutive modeling of temperature and strain rate dependent elastoplastic hardening materials using a corotational rate associated with the plastic deformation

In this paper, a constitutive model with a temperature and strain rate dependent flow stress (Bergstrom hardening rule) and modified Armstrong-Frederick kinematic evolution equation for elastoplastic hardening materials is introduced. Based on the multiplicative decomposition of the deformation gradient,new kinematic relations for the elastic and plastic left stretch tensors as well as the plastic deformation-dependent spin tensor are proposed. Also, a closed-form solution has been obtained for the elastic and plastic left stretch tensors for the simple shear problem.To evaluate model validity, results are compared with known experimental data for SUS 304 stainless steel, which shows a good agreement with the results of the proposed theoretical model.Finally, the stress-deformation curve, as predicted by the model, is plotted for the simple shear problem at room and elevated temperatures using the same material properties for AA5754-O aluminium alloy.     

预应变对中子辐照高纯铝拉伸性能的影响

金属材料的中子辐照硬化和脆化一直都是核能安全领域十分关注的重要问题之一. 为了进一步认识预应变对中子辐照金属材料塑性形变和最终断裂特性的影响规律, 及其微观机理, 本文研究了10%拉伸预应变高纯铝的拉伸应力-应变曲线、失稳应力和失稳应变等随辐照剂量的变化规律. 结果表明, 辐照剂量越高, 预应变高纯铝内部孔洞的尺寸和数密度越高, 导致屈服强度和极限拉伸强度越高, 均匀延伸率和失稳应变越小, 表现出典型的辐照硬化和脆化效应, 但失稳应力与辐照剂量几乎无关. 相同辐照剂量条件下, 预应变引入的高密度位错能够显著降低辐照孔洞的尺寸和数密度, 加之辐照退火效应的综合影响, 导致预应变能够降低高纯铝屈服强度的增长率和失稳应变的下降率, 从而表现出一定的抑制辐照硬化和脆化的能力, 预应变还能够提高高纯铝的失稳应力, 但整体而言预应变并不能提高高纯铝的延性. 最后, 基于J-C本构模型的中子辐照退火态金属材料的脆化模型能够直接应用于预应变金属材料, 且模型预测结果与实验结果吻合较好.      

A crystal plasticity model for strain-path changes in metals

A model is proposed that deals with the transient mechanical anisotropy during strain-path changes in metals. The basic mechanism is assumed to be latent hardening or softening of the slip systems, dependent on if they are active or passive during deformation, reflecting microstructural mechanisms that depend on the deformation mode rather than on the crystallography. The new model captures the experimentally observed behaviour of cross hardening in agreement with experiments for an AA3103 aluminium alloy. Generic results for strain reversals qualitatively agree with two types of behaviour reported in the literature – with or without a plateau on the stress–strain curve. The influence of the model parameters is studied through detailed calculations of the response of three selected parameter combinations, including the evolution of yield surface sections subsequent to 10% pre-strain. The mathematical complexity is kept to a minimum by avoiding explicit predictions related directly to underpinning microstructural changes. The starting point of the model is a combination of conventional texture and work hardening approaches, where an adapted full-constraints Taylor theory and a simple single-crystal work-hardening model for monotonic strain are used. However, the framework of the model is not restricted to these particular models.     

Constitutive model for uniaxial transformation ratchetting of super-elastic NiTi shape memory alloy at room temperature

The transformation ratchetting of super-elastic NiTi shape memory alloy was observed by the uniaxial stress-controlled cyclic tests [Kang, G.Z., Kan, Q.H., Qian, L.M., Liu, Y.J, 2009a. Ratchetting deformation of super-elastic and shape memory NiTi Alloys. Mech. Mater. 41, 139–153]. It is concluded that the NiTi alloy presents apparent ratchetting behaviour, and the ratchetting is collectively caused by the cyclic accumulation of residual induced-martensite and the transformation-induced plastic deformation (i.e., namely transformation ratchetting). Based on the experimental results, a cyclic constitutive model was constructed in the framework of generalized plasticity [Lubliner, J., Auricchio, F., 1996. Generalized plasticity and shape memory alloys. Int. J. Solids Struct. 33, 991–1003] to describe the transformation ratchetting of super-elastic NiTi alloy. The proposed model simultaneously accounts for the evolutions of residual induced-martensite and transformation-induced plastic strain during the stress-controlled cyclic loading by introducing an internal variable z_c, i.e., cumulated induced-martensite volume fraction. The dependence of transformation ratchetting on the applied stress levels and the phase transformation hardening behaviour of the NiTi alloy are also considered in the developed model. The anisotropic phase transformation behaviours of the alloy presented in the tension and compression cases are described by employing a Drucker–Prager-typed transformation surface. It is shown that the simulated results of transformation ratchetting obtained by the proposed model are in good agreement with the corresponding experiments, since the typical features of transformation ratchetting are reasonably captured by the proposed model.     

Plasticity with non-linear kinematic hardening: modelling and shakedown analysis by the bipotential approach

The class of generalised standard materials is not relevant to model the non-associative constitutive equations. The possible generalisation of Fenchel's inequality proposed by de Saxcé allows the recovery of flow rule normality for non-associative behaviours. The normality rule is written in the weak form of an implicit relation. This leads to the introduction of the class of implicit standard materials. This formulation is applied to constitutive equations involving non-linear kinematic hardening, indispensable to describe accurately and realistically the cyclic plasticity of metallic materials. For these plastic flow rules shakedown bound theorems can be extended; an analytical example of the shakedown of a thin-walled tube under constant traction and alternate cyclic torsion is considered and the obtained solution is proved to be exact.     

New flow rules in elasto-viscoplastic constitutive models for spheroidal graphite cast-iron

A specific flow rules and the corresponding constitutive elasto-viscoplastic model combined with new experimental strategy are introduced in order to represent a spheroidal graphite cast-iron behaviour on a wide range of strain, strain rate and temperature. A “full model” is first proposed to correctly reproduce the alloy behaviour even for very small strain levels. A “light model” with a bit poorer experimental agreement but a simpler formulation is also proposed. These macroscopic models, whose equations are based on physical phenomena observed at the dislocation scale, are able to cope with the various load conditions tested – progressive straining and cyclic hardening tests – and to correctly describe anisothermal evolution. The accuracy of these two models and the experimental databases to which they are linked is estimated on different types of experimental tests and compared with the accuracy of more standard Chaboche-type constitutive models. Each test leads to the superiority of the “full model”, particularly for slow strain rates regimes. After developing a material user subroutine, FEM simulations are performed on Abaqus for a car engine exhaust manifold and confirm the good results obtained from the experimental basis. We obtain more accurate results than those given by more traditional laws. A very good correlation is observed between the simulations and the engine bench tests.     

异种不锈钢激光焊缝材料的动态本构关系

利用等应变测试法获取了304及316L激光焊接焊缝材料的准静态应力应变曲线,发现焊缝材料 具有明显的细晶硬脆化趋势。利用SHTB技术对304、316L及焊接构件材料高温动态力学性能进行了研究。 根据动态实验数据对不锈钢304及316L母材应变率及温度相关的Johnson-Cook本构方程参数进行了拟合。 利用LS-DYNA建立了SHTB动态拉伸实验数值模型,发现了在应力波加载初始阶段由于结构效应及材料 阻抗不匹配引起的应力不平衡现象。通过动态实验与数值模拟相结合的方法确定了焊缝材料的应变率相关 本构参数。