Vapor-phase oxidation of β-picoline to nicotinic acid on V2O5 and modified vanadium oxide catalysts

Modification of V₂O₅ with Ti, Sn, Zr, Nb, and Al oxides improves the activity and selectivity of the vanadium oxide catalyst in vapor-phase oxidation of β-picoline to give nicotinic acid. It is shown that the conversion of β-picoline and the yield of nicotinic acid on two-component V₂O₅-TiO₂, V₂O₅-SnO₂, V₂O₅-ZtrO₂, V₂O₅-Nb₂O₅, and V₂O₅-Al₂O₃ catalysts may be several times those on the V₂O₅ catalyst. It was found that, on passing from V₂O₅ to double-component vanadium-containing catalysts, the proton affinity of active oxygen bonded to vanadium, calculated by the quantum-chemical method, grows simultaneously with the increase in the activity of the catalysts in the oxidation reaction.     

Deep oxidation of chlorobenzene on complex catalysts

Deep oxidation of chlorobenzene on γ-alumina catalysts whose active components are V₂O₅, CuCl, or their mixture was studied in relation to the temperature, contact time, and load on the catalyst. The activation energy of the chlorobenzene oxidation on the CuCl-V₂O₅/γ-Al₂O₃ catalyst was determined.     

n-Butane Oxidation over γ-Al2O3 Supported Vanadium Phosphate Catalysts

Four vanadium phosphate catalysts supported onγ-Al_2O_3(20 wt%)were synthesized via wetness impregnation of VOHPO_4·0.5H_2O precursor and calcined for different durations(6,10,30 and 75 h)at 673 K in a reaction flow of n-butane/air mixture.The samples calcined for 6 and 10 h produced only a single phase of(VO)_2P_2O_7.However,the VOPO_4 phase(β-VOPO_4)was detected and became more prominent with only a minor pyrophosphate peaks were found after 30 h of calcination.All these pyrophosphate peaks disappeared after 75 h of calcination.The formation of V~(5 )phase was also observed in the SEM micrographs.The redox properties and the nature of oxidants of the catalysts employed in this study were investigated by H_2-TPR analysis.Selective oxidation of n-butane to maleic anhydride(MA) over these catalysts shows that the percentage of n-butane conversion decreases with the transformation of the catalysts from V~(4 )to V~(5 )phases.An appropriate ratio of V~(5 )/V~(4 )can enhance the performance of the VPO catalyst.However,a higher amount of V~(5 )and its associated oxygen species are responsible to promote the MA selectivity.     

V?Mo?Ox/SiO2 catalysts for acrolein oxidation I. The nature of active sites

The influence of the annealing temperature and the activation of V–Mo–O_x/SiO₂ catalysts for acrolein oxidation has been studied. The catalyst activity decreases with increasing temperature of annealing due to lowering of the number of active sites of V⁴⁺ and the content of active component VMo₃O_11+x.     

贵金属铱对氨分解用镍基催化剂的促进作用研究

用湿式浸渍法制备了不同贵金属质量分数的镍-铱双金属催化剂,以氨分解为模型反应对其催化性能进行考察.结果表明,贵金属铱的添加提高了10%Ni/γ-Al2O3的低温活性.在铱的质量分数不高于1%时,氨分解反应活性随铱质量分数的增加出现最大值(相应的Ir质量分数为0.7%),对应的10%Ni-0.7%Ir/γ-Al2O3催化剂在400 ℃时,氨分解率为43.55%,较单组分的Ni催化剂高40.0%.用H2-TPR、H2-TPD 、BET和XRD表征方法对催化剂进行了表征.结果表明,Ir与活性组分Ni之间存在协同作用.铱的添加促进了活性组分的分散、减小了镍的晶粒尺寸,且增加了催化剂活性位的数量,从而提高了催化剂的氨分解性能.     

不同磷含量对NiMoP/Al2O3加氢处理催化剂的影响

采用NiMoP浸渍液浸渍载体γ Al₂O₃制备了不同磷含量的NiMoP/Al₂O₃加氢处理催化剂。为了研究磷对该系列催化剂活性相结构的影响,用二苯并噻吩（DBT）和喹啉为模型化合物,考察了催化剂的加氢脱硫（HDS）和加氢脱氮（HDN）性能。结果表明,添加适当的磷能够提高催化剂的HDS和HDN活性,但是高含量的磷能显著的降低催化剂的催化性能。通过对催化剂进行XRD和HRTEM表征发现,添加磷能够增加MoS2的堆积层数以及Ⅱ型“Ni-Mo-S”相的相对含量,这是因为在制备过程中添加磷降低了活性组分与载体之间的相互作用。     

Selective oxidation of methanol on V2O5 and V2O5?MoO3 supported on montrmorillonite

Methanol oxidation on V₂O₅ and V₂O₅–MoO₃ catalysts supported on montmorillonite has been studied in the temperature range of 250–500°C. The V₂O₅–MoO₃ containing sample shows higher selectivity towards formaldehyde formation than the V₂O₅ catalyst.     

Role of metal Cu species on methyl laurate catalytic hydrogenation to oxygen-containing compounds

The Cu/γ-Al₂O₃ catalysts with different Cu loadings were prepared by impregnation method. The physicochemical properties of these Cu/γ-Al₂O₃ catalysts were characterized by H₂-TPR, XRD, and in-situ XPS. The catalytic hydrogenation performances of methyl laurate over Cu/γ-Al₂O₃ catalysts were studied. The results show that the hydrogenation performances of methyl laurate on Cu/γ-Al₂O₃ catalyst are related to the dispersion, crystallite size, and content of the active component Cu⁰. The 10CA catalyst has the best hydrogenation performances for methyl laurate to produce C₁₂ alcohol. At 300 °C, the conversion of methyl laurate and the selectivity of C₁₂ alcohol are 55.6% and 30.4%, respectively.     

Dehydrogenation of Isobutane Over V2O5/γ-Al2O3 Catalyst

The effect of the type of the support and the amount of V₂O₅ loading on the activity of V₂O₅/γ-Al₂O₃ catalyst for the dehydrogenation of isobutane have been investigated. Based on the experimental results of TPR, XRD and ESR spectroscopy, it is suggested that there are strong interactions between vanadia and carrier and that the V⁴⁺ species on the surface is the active site of V₂O₅/γ-Al₂O₃ for this reaction. This revised version was published online in June 2006 with corrections to the Cover Date.     

Fe- and Cu-oxides supported on γ-Al2O3 as catalysts for the selective catalytic reduction of NO with ethanol. Part I: catalyst preparation,characterization, and activity

Fe- and Cu-oxides supported on γ-alumina (γ-Al₂O₃; metal loading of 3 mass %) were investigated as alternative catalysts to the conventional Ag-based system in the selective catalytic reduction of NO with ethanol (EtOH-SCR). The catalysts were characterized by elemental analysis, N₂ sorption, X-ray diffraction, temperature-prgrammed desorption of NH₃, temperature-programmed reduction with H2, diffuse reflectance UV-VIS (DR-UV-VIS) spectroscopy, and compared with 3 mass % Ag/γ-Al₂O₃ as a reference catalyst. Catalytic experiments were carried out between 423 K and 773 K in the steady state and by temperature-programmed surface reaction (TPSR) experiments. For all catalysts, the highest NO conversion (900 ppm (ppm = parts of the mixture component per million parts of all mixture components) NO, 900 ppm EtOH, 0.5 vol. % H₂O, 4 vol. % O₂ in He) was found at 573 K. While 84 % of NO were converted over the Ag-based catalysts, only 20–60 % NO conversion was observed for the Fe- and Cu-containing catalysts. Total oxidation of ethanol as an unwanted side reaction occurs over 3 mass % Cu on γ-Al₂O₃ already at 573 K, whereas the highest activity of 3 mass % Fe on γ-Al₂O₃ for this conversion was reached at 743 K. For lower temperatures, partial oxidation of ethanol leads to organic by-products which can act as active intermediates in EtOH-SCR. TPSR experiments show that ethanol reacts over both the Fe- and the Cu-based catalysts to organic by-products, such as ethene or acetaldehyde, which affect the EtOH-SCR reaction.     

Ultra‐deep desulfurization of a model fuel using novel VOHPO4 0.5H2O/boehmite catalysts

A high‐surface‐area boehmite was used as the support for a series of vanadium phosphate catalysts. The catalysts were prepared by heating of V₂O₅ in an isobutyl alcohol and benzyl alcohol mixture at 140°C for 5 h to reduce V⁵⁺ to more active V⁴⁺ in the presence of phosphoric acid. Then a series of catalysts with various VPO loadings on boehmite were synthesized. The catalysts were characterized using various techniques. The catalysts were utilized for extraction combined with catalytic oxidation of dibenzothiophene. The important factors influencing the desulfurization process, including reaction time, temperature, H₂O₂, catalyst loading, catalyst amount and solvents, were systematically investigated. Under the optimized reaction conditions, i.e. 30 mg of catalyst loading at 50°C and in 60 min, sulfur removal reached 94%. The catalyst was recycled and reused five times.     

Photocatalytic degradation of organophosphate flame retardant TBEP: kinetics and identification of transformation products by orbitrap mass spectrometry

The photocatalytic degradation of tris (2–butoxyethyl) phosphate (TBEP) flame retardant using visible light response catalysts TiO₂/V₂O₅, (N,F-doped)-TiO₂/V₂O₅, and N-doped-SrTiO₃ has been studied by high-resolution orbitrap mass spectrometry. TBEP degradation followed first-order kinetics with half-life values ranging between 9.8 and 83.5 min. N-doped-SrTiO₃ was the catalyst with better photocatalytic performance while activity for TiO₂/V₂O₅ composites followed the trend: N, F- TiO₂/V₂O₅ > N-TiO₂/V₂O₅> TiO₂/V₂O₅. The identified degradation products (DPs) revealed hydroxylation, further oxidation and dealkylation as major degradation pathways. Based on the identified DPs and scavenging experiments, ^?OH radical-mediated reactions can be considered for the degradation of TBEP using TiO₂ and SrTiO₃-based photocatalytic materials.     

Ce改性的Pt/γ-AlO3催化剂用于富氢气氛下CO选择氧化

研究了Ce改性的Pt/γ-AlO3对于富氢气氛下CO选择氧化反应的催化行为考察了制备条件（共沉积沉淀法、分步沉积沉淀法以及沉积沉淀温度）对催化活性的影响．结果表明，在80℃时用共沉积沉淀方法制备的催化剂Pt/γ-AlO3-CP-80对CO氧化反应表现出良好的活性和选择性，CO转化率在120℃时可以达到85％．利用氢气程序升温还原和原位漫反射红外光谱对不同条件下制备的催化剂进行了表征，分析了Cc的促进作用．     

High catalytic activity of V2O5-ZrO2 modified with H2SO4 for propene partial oxidation

For V₂O₅–ZrO₂ catalysts, up to 10 mol% the crystalline structure of V₂O₅ was not observed, indicating a good dispersity the surface of ZrO₂. V₂O₅–ZrO₂ catalyst modified with H₂SO₄ exhibited much on higher catalytic activity for propene partial oxidation than unmodified catalysts due to the increased acidity and acid strength of modified catalyst.     

Effect of Mg/Al atom ratio of support on catalytic performance of Co-Mo/MgO-Al2O3 catalyst for water gas shift reaction

Co-Mo-based catalysts supported on mixed oxide supports MgO-Al₂O₃ with different Mg/Al atom ratios for water gas shift reaction were studied by means of TPR, Raman, XPS and ESR. It was found that the octahedral Mo species in oxidized Co-Mo/MgO(x)-Al₂O₃ catalyst and the contents of Mo⁵⁺, Mo⁴⁺, S²⁻ and S²⁻₂ species in the functioning catalysts increased with increasing the Mg/Al atom ratio of the support under the studied experimental conditions. This is favorable for the formation of the active Co-Mo-S phase of the catalysts. Catalytic performance testing results showed that the catalysts Co-Mo/MgO-Al₂O₃ with the Mg/Al atom ratio of the support in the range of 0.475–0.525 exhibited optimal catalytic activity for the reaction.     

Preparation of Highly Active Pt-K/γ-Al2O3 Catalyst for o-Phenylphenol Synthesis from o-Cyclohexenyl-cyclohexanone Dehydrogenation

0.5%Pt-K/γ-Al2O3 catalysts for the synthesis of o-phenylphenol（OPP） from o-cyclohexenyl-cyclohexanone （dimer） dehydrogenation were prepared by means of a two subsequent impregnation method. The effects of catalyst preparation parameters, such as K promoters, calcination, and reduction conditions, were investigated. The results showed that the addition of K2SO4 to Pt/γ-Al2O3 catalyst notably promoted the selectivity of OPP, and its optimum content was found to be 6% in mass fraction. The higher activity was obtained when Pt/γ-Al2O3 catalyst was calcined in nitrogen atmosphere at 400--500 ℃ and then reduced at the same temperature for 3 h in hydrogen atmosphere. The conversion of the dimer and the selectivity of OPP were always above 99% and 90%, respectively, over 0.5%Pt-6% K2SO4/γ-Al2O3 catalyst during the pilot scale test of 8000 h.     

Kinetic Peculiarities in the Low-Temperature Oxidation of H2S on Vanadium Catalysts

H₂S oxidation by oxygen on catalysts V₂O₅/Al₂O₃, V₂O₅/TiO₂, V₂O₅/Al₂O₃/TiO₂ was studied at temperatures below the sulfur dew point. High activity and the oscillation character of the oxidation were demonstrated by catalysts with low contents of V₂O₅ (3–5 wt.%). The increase in the V₂O₅ concentration to 10–20 wt.% results in the reduction of the catalytic activity and oscillation ability. On a pure V₂O₅ catalyst, the oscillations were not detected. The difference between the catalysts with the high and low concentrations of V₂O₅ is explained in terms of the structures of the V⁵⁺ species formed in the catalysts. This revised version was published online in June 2006 with corrections to the Cover Date.     

Oxidation of methane, butane and carbon monoxide on Al?Fe oxide catalysts

The activity of the catalysts obtained by supporting Fe³⁺ oxalate complexes on -and -Al₂O₃ in oxidation of CH₄, C₄H₁₀ and CO has been studied. The composition of the impregnating solution and the temperature of catalyst thermal treatment were varied. The most active catalysts were prepared by impregnation of -Al₂O₃ with (NH₄)₃[Fe(C₂O₄)₃] solutions at pH=2.0–3.5. Their activity appears to be close to that of Al-Mg-Cr catalysts in butane oxidation and even exceeds this in CO oxidation.     

Cerium-containing catalysts for converting ethanol into ethylene

Ce/γ-Al₂O₃ and CeLa/γ-Al₂O₃ catalysts are studied via electron microscopy and temperature-programmed desorption of ammonia. Their activity in the dehydration of ethanol is investigated. Doping Ce/γ-Al₂O₃ catalyst with lanthanum is shown to increase its dispersion and the number of active acid sites, thereby improving its activity.