利用水热合成方法制备正交氮化硼微晶

利用水热方法制备了正交氮化硼微晶, 于400 ℃时制备的氮化硼结晶质量较高, 主要物相为正交氮化硼(oBN). 在反应原料中加入水合肼和氯化铵都有利于样品结晶质量的改善和产率的提高. 在合成氮化硼反应过程中, 适当减慢反应体系的升温速率有利于提高oBN的结晶质量和产率, 但是当升温速率过慢时, oBN的稳定性有所降低, 立方氮化硼(cBN)的稳定性则在一定程度上得到提高. 此外, 反应过程中的原料配比对样品的物相及其结晶质量也有很大影响.     

Effects of Temperature Raising Speed on the Growth of BN Crystals in Hydrothermal Solutions

Cubic boron nitride (cBN) and orthorhombic boron nitride (oBN) crystals have been prepared in hydrothermal solutions by reacting H3BO3 NaN3 P and H3BO3 NaN3 N2H4 respectively. The experimental results indicated that, if the temperature was increased rapidly, both the yield and perfectness of BN crystals became poor. On the contrast, the yield and perfectness of BN crystals can be improved very much by slowly increasing the temperature of the reaction mixture. The results of X-ray powder diffraction (XRD), Fourier transform infrared spectrum (FTIR) and high resolution transmission electron microscopy (HRTEM) proved that the samples were composed of oBN and cBN.     

Multi-step Reaction Route Developed for Improving Crystallinity of Boron Nitride Nanoparticles

A multi-step reaction route was developed to synthesize boron nitride(BN) nanoparticles via the reaction between NaN₃ and BCl₃ in a benzene-thermal solution. By means of this route, the crystallinity of BN nanoparticles was improved via increasing the reaction steps. Meanwhile, a phase transformation from hexagonal BN(hBN) or turbostratic BN(tBN) to cubic BN(cBN) occurred, resulting in the increase of cBN content. Moreover, the content of cBN also slightly increased when the temperature was elevated from 265 ℃ to 280 ℃.     

Studying the growth of cubic boron nitride on amorphous tetrahedral carbon interlayers

The growth of cubic boron nitride (cBN) films on bare silicon and amorphous tetrahedral carbon (ta-C) layers prepared on silicon substrates was studied. The cBN films were prepared by radio frequency magnetron sputter deposition at approximately 870 degrees C. The original ta-C interlayers were graphitized and restructured under high temperature and possibly under ion bombardment during BN deposition. The majority of graphitic basal planes were nearly perpendicular to the surface of silicon substrates. The BN films grown on these restructured carbon layers were deposited with higher content of cubic phase and did not show delamination signs. Turbostratic BN (tBN) basal planes extended carbon basal planes and their edges served as cBN nucleation sites. The cBN films grown on textured ta-C interlayers were insensitive to the ambient environment. The residual sp(3)-bonded carbon phase confined in the interlayers probably acts as a diffusion barrier preventing the oxidation of dangling bonds near BN interface and thus precludes weakening the interface as a result of volume expansion. The carbon interlayers also improve the crystallinity of the oriented tBN because they are continuation of carbon graphitic basal planes so that the volume fraction of nitrogen-void (N-void) defects in the sp(2)-bonded BN intermediate layers is reduced. The strong sp(3)-bonded carbon matrix could thereto withstand large compressive stress and facilitates deposition of thicker cBN films.     

高温高压Li3N-hBN体系cBN转变的热力学分析

以经典热力学第二定律ΔG<0为依据,分析了静态高温高压触媒法合成立方氮化硼(cBN)过程中发生的可能反应.考虑温度和压强对反应物相体积的影响,计算了六方氮化硼(Li3N-hBN)体系中hBN+Li3N→Li3BN2,h BN→cBN及Li3BN2→Li3N+cBN反应在高温高压条件下的ΔG.结果证实,Li3BN2由Li3N与hBN在高温高压(T>1300 K,P>3.0 GPa)条件下反应得到,在cBN的合成(T=1600～1800 K,P=4.6～6.0 GPa)条件下,hBN和Li3BN2都有向cBN转化的倾向,但由hBN向cBN直接转变的反应自由能比Li3BN2分解生成cBN的反应自由能更负,反应的可能性更大.探讨了高温高压条件下立方氮化硼的转变机理。     

Phase transformation of boron nitride under hypothermal conditions

Phase transformation among different boron nitride (BN) phases in hydrothermal solution was investigated. It was found that hexagonal boron nitride (hBN) firstly formed in the solution at relatively low temperature (i.e., 220 °C). After that, a spot of hBN began to transform into wurtzite boron nitride (wBN) and cubic boron nitride (cBN) at 230 °C. More and more hBN converted into wBN and cBN with the increase in temperature, and this transformation process completed at 300 °C. In this paper, we have explained the mechanism of the above phase transformation by using a reported “puckering mechanism”.     

水相循环对玉米秸秆水热液化成油特性影响的研究

以玉米秸秆为原料,以去离子水为介质,研究水相循环对玉米秸秆水热液化成油特性的影响。循环过程中不额外添加去离子水,对循环前后的水相产物、生物原油和固体产物进行对比研究发现,水相循环产生有机酸的富集效应,促进酮酚类的转化,两者共同作用提高生物原油和固体产物的产率和品质。具体表现为:水相循环对水相pH值影响较小(3. 62-3. 91),但可以使乙酸和丙酸等有机酸不断累积,同时使酮类、酚类化合物含量逐渐减少;水相循环可以使生物原油产率从20. 42%逐步提高至24. 31%,且可略提升油品质;水相循环可以使固体产物的碳含量由60. 94%提升至61. 74%。     

Interfacial study of cubic boron nitride films deposited on diamond

We have studied the nucleation and growth of cubic boron nitride (cBN) films deposited on silicon and diamond-coated silicon substrates using fluorine-assisted chemical vapor deposition (CVD). These comparative studies substantiate that the incubation amorphous/turbostratic BN layers, essential for the cBN nucleation on silicon, are not vital precursors for cBN nucleation on diamond, and they are inherently eliminated. At vastly reduced critical bias voltage, down to -10 V, cBN growth is still maintained on diamond surfaces, and cBN and underlying diamond crystallites exhibit an epitaxial relationship. However, the epitaxial growth is associated with stress in the cBN-diamond interfacial region. In addition, some twinning of crystallites and small-angle grain boundaries are observed between the cBN and diamond crystallites because of the slight lattice mismatch of 1.36%. The small-angle grain boundaries could be eliminated by imposing a little higher bias voltage during the initial growth stage. The heteroepitaxial growth of cBN films on different substrate materials are discussed in the view of lattice matching, surface-energy compatibility, and stability of the substrate against ion irradiation.     

Radiochemical and biological characteristics of radioactive iodine labeled indomethacin for imaging of inflammation

Summary Indomethacin was successfully labeled with ¹²⁵I. This labeling reaction was carried out via electrophilic substitution of hydrogen atom with the iodonium atom I⁺. The reaction was found to be strongly dependent on pH of the reaction medium. At neutral pH value, 7 the labeling yield was maximum. This may be due to the good solubility of indomethacin, good protonation and good working of the oxidizing agent at this pH value. Towards the acidic pH value, the yield decreased and towards the alkaline pH value the yield decreased due to the decomposition of the indomethacin. The labeling reaction is very fast but needs five minutes for completion. The produced ¹²⁵I-indomethacin was found stable in-vivo as the thyroid gland uptake did not exceed 2%. Labeled indomethacin shows a good localization in inflamed muscle, either septic or sterile. It excretes mainly via liver and to some extent via kidney. The imaging must be carried out at 24-hour post injection, after that time, the background activity has cleared and the activity is concentrated in the target site.     

Hydrothermal hot-pressing induced phase transition in hexagonal boron nitride

The phase transition of hBN nanocrystals induced by hydrothermal hot-pressing process has been investigated by XRD, FTIR, TEM and HRTEM. It was found that a phase transition of hBN → tBN → aBN occurred with increasing hot-pressing temperature, i.e., hBN transformed into tBN at above 270 °C, and followed by another transformation from tBN to aBN at 310 °C. In addition, FTIR spectra and HRTEM images indicate that a small amount of cBN formed directly from the amorphous BN matrix at 75 MPa and 310 °C. This phenomenon is similar to what happened in conventional high temperature and high pressure method, which is believed to promote the phase transition from hBN to cBN.     

Facile Fabrication of Nanorod‐Assembled Fluorine‐Substituted Hydroxyapatite (FHA) Microspheres

Nanorod‐assembled FHA microspheres with different F contents were for the first time prepared through a facile one‐step hydrothermal method. The effect of the reaction time and pH value of reaction solutions on the FHA morphology was investigated to elucidate the self‐assembly process of FHA microspheres. The results showed pH values had significant effect on the morphology of the formed FHA crystals, which were self‐assembled into sphere‐like sturctures at high pH conditions and rod‐like structures at low pH values. The results suggested that formation of FHA crystals with varied morphology may be directly related to Ca²⁺ release kinetics from EDTA‐Ca‐Na₂ at different pH conditions. Furthermore, it was found that the chemical stability of FHA microspheres was dependent on the F content in the materials, and high F contents in FHA microspheres lead to improved chemical stability. These results suggest that the prepared self‐assembled FHA microspheres may be used for teeth substitution materials due to their unique hierarchical structures and controllable chemical stability.     

自发团聚诱导高比例立方氮化硼微晶的水热合成

利用水热法合成了立方氮化硼（cBN）. 通常水热法制备的氮化硼样品是立方氮化硼（cBN）和六方氮化硼（hBN）及其它晶相的混合物,这限制了该方法的应用前景. 文中利用立方氮化硼在特定反应条件下的自发团聚现象,成功地发展了一种使混合物中的立方氮化硼在反应过程中自发纯化的新方法. 提高原料浓度和反应温度,有利于获得更大粒径的立方氮化硼和尺寸分布更均匀的团聚颗粒,提高搅拌转速来改善溶液的均匀性也有同样效果;而提高反应压力则会导致相反的结果. 文中也探讨了自团聚现象在生长大尺寸立方氮化硼晶体以及非均相合成中的潜在应用价值.     

水热处理对白石湖煤热解过程中钠钙迁移行为的影响

采用高压釜对富镜质组白石湖煤进行了水热处理,通过傅里叶红外光谱(FT-IR)分峰拟合方法分析了煤中含氧官能团变化。在固定床中开展分离废液和未分离废液水热处理煤样的热解实验,利用原子吸收分光光度计(AAS)测定了热解产物中钠钙含量。结果表明,白石湖煤经水热处理后水分、挥发分、氧含量以及Cl、Na和Ca等无机元素含量明显降低。水热处理过程中芳香醚水解和羧酸盐发生离子交换反应使得氢含量和H/C原子比增加,促进固定床热解焦油产率升高。300℃下水热处理脱除了部分有机形式Ca后随水废液被分离;废液中钠钙等无机元素的催化作用导致未分离废液较分离废液的样品具有更高热解气产率和更低焦油产率。白石湖原煤及其水热处理样品热解产物中Na含量和分布由高到低顺序均为:热解焦热解水焦油热解气,Ca含量和分布顺序为:热解焦焦油热解水热解气。水热处理温度越高,热解过程钠和钙释放率越低,释放的Na主要进入热解水,其次焦油;而释放的Ca则主要分布于焦油中,其次热解水。     

氢氧化镍纳米棒的水热制备及其表征

以Ni₂SO₄·6H₂O和NaOH为原料,在水热条件下制备了氢氧化镍纳米棒.运用透射电子显微镜(TEM)和X射线衍射仪(XRD)对样品进行了表征,考察了水热反应温度和pH值对产物的形貌和结构的影响.结果表明,氢氧化镍纳米棒形成的最佳条件是180～200℃,pH为9～10.     

酶法动力学拆分制备光学活性γ-内酯

研究了脂肪酶对桃醛和γ-癸内酯的水解动力学拆分反应,考察了温度、pH值、酶的用量等因素对酶催化水解拆分过程的影响.选择氯化钙-阿拉伯胶水溶液作为反应介质,使γ-内酯拆分产物取得较高的ee值.回收拆分中产生的γ-羟基酸,外消旋化后再内酯化,投入下一批反应,提高了光学活性γ-内酯的总得率.     

高性能自修复微胶囊预聚物组成的研究

为了指导高性能自修复微胶囊的制备研究, 利用偏光显微熔点仪、红外光谱和核磁共振氢谱定量研究了微胶囊预聚物组成随反应条件如反应温度、pH 值和甲醛-尿素物质的量比的变化. 研究结果表明, 升高体系温度和pH 值都会显著促进副反应的发生从而降低产物中二羟甲基脲的产率; 而提高甲醛-尿素的物质的量比, 二羟甲基脲的产率增加,同时三羟甲基脲的产率降低. 此外, 还研究了升温过程中反应体系的温度变化情况. 研究发现: 升温速率一定时, 反应体系的温度变化均匀, 没有温度骤变阶段.     

钛硅分子筛催化1-丁烯环氧化反应溶剂效应和酸碱效应研究

研究了用双氧水为氧化剂，钛硅分子筛TS-1催化1-丁烯环氧化反应的溶剂效应．研究发现，在质子性溶剂中1-丁烯环氧化反应活性高于非质子性溶剂，而以甲醇为溶剂H2O2转化率最高．分别利用碱性添加物稀氨水溶液和酸性添加物稀盐酸溶液调变反应介质的pH值，考察了介质的pH值对1-丁烯环氧化反应的影响，结果表明，随pH值提高，1，2-环氧丁烷(B0)的选择性略提高，但是过量稀氨水的加入会导致催化剂失活，双氧水的转化率及利用率明显下降．与钛硅分子筛催化丙烯环氧化相比，酸性添加物的加入对反应结果的影响不大，随反应介质的pH值降低1，2-环氧丁烷的选择性没有明显下降．     

利用偏钛酸浆料制备大比表面纳米管钛酸工艺的研究

以偏钛酸浆料为原料通过水热法合成了纳米管钛酸,并采用TEM,比表面积测定仪等分析手段观察其形貌和管径大小,测定了其比表面积和孔体积.同时运用正交实验法考察了反应温度、反应时间对纳米管钛酸比表面积和孔体积的影响.实验结果表明,所制备的纳米管钛酸平均比表面积高达 340m2 /g,最佳的制备工艺是:工业碱NaOH的质量分数为 25. 7 %、偏钛酸浆料的质量分数为 17. 1 %、后处理酸度为pH=1、反应温度为 120℃、反应时间为 20h.     

碳纳米管/氧化锌纳米复合材料的制备及其形貌控制

0引言碳纳米管(CNT)优良的力学、电学、热学性能使其在材料、储能、传感等许多领域都有广泛的应用前景,近年来,以碳纳米管为载体制备的纳米复合材料因其独特的应用潜力而受到广泛关注:彭峰等[1]用FeSO4-H2O2体系修饰碳纳米管,成功地制备了由碳纳米管负载的Fe2O3催化剂;Chen等[2]用溶胶凝胶法制备了CNT/SnO复合材料,作为Li离子电池阴极材料,测试表明它的电化学性能比单独的CNT和SnO材料都有所增强;Jitianu等[3]用溶胶凝胶和水热方法得到不同形貌的TiO2/CNT复合结构,这种新型的纳米复合材料在光催化方面有着重要的应用前景。纳米Z…     

YBO3:Eu荧光粉的水热法制备及形貌控制

用水热法在低于300℃成功地制备出具有不同形貌的YBO3:Eu3+荧光粉,其反应温度比固相反应了约800℃.研究了初始原料、pH值、反应温度、反应溶剂和催化剂等条件对目的产物形貌及粒度的,得到了具有Vaterite结构、粒度分布均匀的球形荧光粉的最佳合成工艺.在254nm激发下,水热法的球形Y0.95Eu0.05BO3荧光粉最强发射峰位于598nm处,属于Eu3+的5D0→7F1的跃迁,是固相反应所品的1.5倍.这些结果表明,在PDP和荧光灯等显示和照明用荧光粉的制备中水热法具有潜在的应用.