低温静电自组装法制备贵金属修饰TiO_2纳米结构薄膜及其增强的光催化性能(英文)

以碱-水热法在金属Ti片上原位生长了TiO2纳米结构(纳米花和纳米线)薄膜,并采用低温静电自组装方法将超细贵金属(金、铂、钯)纳米颗粒均匀沉积于多孔TiO2薄膜上.负载于Ti片上的贵金属/TiO2纳米结构薄膜具有一体化结构、多孔架构和高光催化活性.超高分辨率场发射扫描电子显微镜(FESEM)直接观察表明贵金属纳米颗粒在TiO2表面分布均匀,且颗粒之间相互分离,金、铂、钯纳米颗粒的平均粒径分别约为4.0、2.0和10.0nm.俄歇电子能谱(AES)纵深成分分析表明贵金属不仅沉积于薄膜表面,且大量分布于TiO2纳米结构薄膜内部,其深度超过580 nm.X射线光电子能谱(XPS)分析表明,经300°C下在空气中热处理后,纳米金仍保持金属态,纳米铂部分被氧化成PtOabs,而钯粒子则完全被氧化成氧化钯(PdO).以低温静电自组装法沉积贵金属,贵金属负载量可通过调节组装时间与溶胶pH值来控制.光催化降解甲基橙的结果表明,沉积的纳米金和铂能显著增加TiO2纳米结构薄膜的光催化活性,说明金和铂粒子可促进光生载流子的分离;但负载的PdO对TiO2薄膜的光催化性能增强几乎无作用.     

Preparation of nanocrystalline porous titania films on titanium substrates by a sol–gel method with polyethylene glycol as a template

Porous nanocrystalline TiO₂ films have been prepared on cp-Ti substrates for biomedical usage by a sol–gel process from the solutions containing polyethylene glycol (PEG) as a template. Variations of the crystal structure with heat-treatment temperature determined by XRD are different for TiO₂ films and powders, due to the effect of titanium substrate. The surface texture of porous TiO₂ films is analyzed by means of SEM and found to greatly depend on the concentration and molecular weight of PEG. The pore formation mechanism is discussed in relation to the self-assembly of PEG and phase separation between PEG adsorbed on TiO₂ oligomers and ethanol.     

Macroporous ordered titanium dioxide (TiO2) inverse opal as a new label-free immunosensor

Photonic crystal sensing materials have been validated that they are very sensitive to refractive index changes. Herein, three-dimensionally ordered macroporous (3DOM) (>50 nm) TiO₂ inverse opal film has been fabricated by the self-assembly technique. Based on the TiO₂ inverse opal film, the optical spectrometer was established for label-free immunosensor. The sensing performance of the 3DOM TiO₂ was investigated using human IgG/goat anti-human IgG couple, which showed that the sensitivity of 3DOM TiO₂ inverse opal film could reach to 1 μg mL⁻¹ (equivalent to 1.5 pg mm⁻²) of protein concentration detection limit. The 3DOM TiO₂ inverse opal has a large internal surface area, low fluorescence background and unique optical properties. These characteristics indicated the feasibility of 3DOM TiO₂ inverse opal in label-free immunoassay.     

Titania-lanthanum phosphate photoactive and hydrophobic new generation catalyst

Titania-lanthanum phosphate nanocomposites with multifunctional properties have been synthesized by aqueous sol-gel method. The precursor sols with varying TiO₂:LaPO₄ ratios were applied as thin coating on glass substrates in order to be transparent, hydrophobic, photocatalytically active coatings. The phase compositions of the composite powders were identified by powder X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HR-TEM). The anatase phase of TiO₂ in TiO₂-LaPO₄ composite precursors was found to be stable even on annealing at 800 °C. The glass substrates, coated with TL1 (TiO₂-LaPO₄ composition with 1 mol% LaPO₄) and TL50 (composite precursor containing TiO₂ and LaPO₄ with molar ratio 1:1) sols and annealed at 400 °C, produced contact angles of 74° and 92°, respectively, though it is only 62° for pure TiO₂ coating. The glass substrates, coated with TL50 sol, produced surfaces with relatively high roughness and uneven morphology. The TL1 material, annealed at 800 °C, has shown the highest UV photoactivity with an apparent rate constant, k_app=24×10⁻³ min⁻¹, which is over five times higher than that observed with standard Hombikat UV 100 (k_app=4×10⁻³ min⁻¹). The photoactivity combined with a moderate contact angle (85.3°) shows that this material has a promise as an efficient self-cleaning precursor.     

Fabrication and photoelectrochemical properties of porous ZnWO4 film

Porous ZnWO₄ films have been fabricated on Indium-tin oxide (ITO) glass and its photoelectrochemical properties and high photocatalytic activities towards degradation of rhodamine B (RhB) has been investigated. Using amorphous heteronuclear complex as precursor and with the addition of polyethylene glycol (PEG, molecular weight=400), the porous ZnWO₄ films have been achieved at the temperature of 500 °C via dip-coating method. It is composed of approximately 70 nm-sized particles and exhibits substantial porosity. The textures and porosity of ZnWO₄ films are dependent on preparation factors, such as the ratio of precursor/PEG and the annealing conditions. The formation mechanism of porous ZnWO₄ films was proposed. The porous ZnWO₄ films exhibited high photocatalytic activities towards degrading RhB. The top of valence band and the bottom of the conduction band was estimated to be −0.56 and 3.45 eV (vs. saturated calomel electrode (SCE)), respectively.     

Highly conducting gold nanoparticles-graphene nanohybrid films for ultrasensitive detection of carcinoembryonic antigen

A new label-free amperometric immunosensor was developed for detection of carcinoembryonic antigen (CEA) based on chitosan-ferrocene (CS-Fc) and nano-TiO₂ (CS-Fc + TiO₂) complex film and gold nanoparticles-graphene (Au-Gra) nanohybrid. CS-Fc + TiO₂ composite membrane was first modified on a bare glass carbon electrode. Then Au-Gra nanohybrid was formed on the CS-Fc + TiO₂ membrane by self-assembly strategy. Next, further immobilization of anti-CEA was constructed according to the strong interaction between Au-Gra and the amido groups of anti-CEA. Since Au-Gra nanohybrid films provided a congenial microenvironment for the immobilization of biomolecules, the surface coverage of antibody protein could be enhanced and the sensitivity of the immunosensor has been improved. The good electronic conductive characteristic might be attributed to the synergistic effect of graphene nanosheets and Au NPs. The modified process was characterized by scanning electron microscope (SEM) and cyclic voltammetry (CV). Under optimized conditions, the resulting biosensor displayed good amperometric response to CEA with linear range from 0.01 to 80 ng/mL and a detection limit of 3.4 pg/mL (signal/noise = 3). The results demonstrated that the immunosensor has advantages of high conduction, sensitivity, and long life time. This assay approach showed a great potential in clinical applications and detection of low level proteins.     

Optimization of the photocatalytic activity of CdO + CdTiO3 coupled oxide thin films obtained by sol-gel technique

In the preparation of CdO + CdTiO₃ polycrystalline thin films by the sol-gel method, the optical, structural and crystalline properties, as well as the photocatalytic activity (PA) depends strongly on the sintering temperature (Ts) of the films and of the Ti/Cd ratio used in the precursor solution. In this work, CdO + CdTiO₃ thin films were prepared using a Ti/Cd constant ratio in the precursor solution. The films were sintered at six different Ts in the 450-550 °C range, in an open atmosphere. The structure of the films was characterized by X-ray diffraction and the PA was evaluated by the photobleaching of methylene blue in an aqueous solution using a UV-vis spectrometer. The relative intensity of the diffraction peaks associated with CdO and CdTiO₃, change with the Ts. The better photocatalytic activities were obtained for the films sintered at 490 °C and 550 °C. When the CdO was removed from the films by chemical etching the PA decreased, showing the importance of coupling both oxides.     

钛、铝和玻璃上TiO2光催化膜的失活研究

采用浸渍提拉法，在平行条件下制备了钛、铝和玻璃载体上的TiO₂膜TiO₂ / Ti、TiO₂ / Al和TiO₂ / G，利用X射线光电子能谱(XPS)、原子力显微镜(AFM)和光催化降解实验等手段对膜样品进行了表征和活性评价。实验结果表明，在铝和玻璃基材上制膜时发生了显著的基材元素溢出，使各膜样品的化学组成不同，同时TiO₂粒子和膜表面形貌也因前驱物烧结行为不同而差异较大。TiO_{2相似文献}   

Novel low humidity sensor made of TiO(2) nanowires/poly(2-acrylamido-2-methylpropane sulfonate) composite material film combined with quartz crystal microbalance

A novel ceramic nanowires of TiO₂ and poly(2-acrylamido-2-methylpropane sulfonate) (TiO₂ NWs/PAMPS) composite material films coated on quartz crystal microbalance (QCM) was prepared as a low humidity sensor. The 50 wt.% of TiO₂ NWs/PAMPS composite material films showed excellent sensitivity (2.63 −ΔHz/Δppm_v) at 31.5 ppm_v), linearity (R² = 0.9959) and acceptable response time (64 s at 34.6 ppm_v). The low humidity sensing mechanism was discussed in terms of surface texture and nanostructured morphology of the composite materials. Moreover, the adsorption dynamic analysis, molecular mechanics calculation (association constant), was used to elucidate the effect of adding 50 wt.% TiO₂ NWs into PAMPS in the increased sensitivity of low humidity sensing.     

Characterization and photocatalytic activity of Fe- and N-co-deposited TiO2 and first-principles study for electronic structure

Titanium dioxide (TiO₂), co-deposited with Fe and N, is first implanted with Fe by a metal plasma ion implantation (MPII) process and then annealed in N₂ atmosphere at a temperature regime of 400-600 °C. First-principle calculations show that the (Fe, N) co-deposited TiO₂ films produced additional band gap levels at the bottom of the conduction band (CB) and on the top of the valence band (VB). The (Fe, N) co-deposited TiO₂ films were effective in both prohibiting electron-hole recombination and generating additional Fe-O and N-Ti-O impurity levels for the TiO₂ band gap. The (Fe, N) co-deposited TiO₂ has a narrower band gap of 1.97 eV than Fe-implanted TiO₂ (3.14 eV) and N-doped TiO₂ (2.16 eV). A significant reduction of TiO₂ band gap energy from 3.22 to 1.97 eV was achieved, which resulted in the extension of photocatalytic activity of TiO₂ from UV to Vis regime. The photocatalytic activity and removal rate were approximately two-fold higher than that of the Fe-implanted TiO₂ under visible light irradiation.     

CdS thin films on LiNbO3 (1 0 4) and silicon (1 1 1) substrates prepared through an atom substitution method

CdS thin films on LiNbO₃ (1 0 4) and silicon (1 1 1) substrates were prepared through an atom substitution technique using cadmium nitrate as a reactant in an H₂S atmosphere at 230 °C. X−ray diffraction, scanning electron microscopy and transmission microscopy results indicate that the CdS film grows on LiNbO₃ oriented along the [0 0 1] axis in form of crystallized nanoplates, while that deposited on silicon forms randomly oriented nanoparticles. Investigation of the precursor thin film suggests that CdS forms from the O in the CdO precursor thin film being substituted by S from H₂S in the surrounding environment, which is designated as an atom substitution process. This novel method involving an atom substitution reaction between the CdO precursor thin film and its environment can provide a new low cost approach to the preparation of chalcogenide or other compound thin films. A schematic illustration and corresponding mechanism describing the details of this method are proposed.     

Characterization of silicone oil emulsions stabilized by TiO2 suspensions pre-adsorbed SDS

To study the effects of pre-adsorbed emulsifier on Pickering emulsion stability, the preparation of silicone oil emulsions by TiO₂ suspensions pre-adsorbed sodium dodecyl sulfate (SDS) at the fixed TiO₂ concentration of 0.15 g was carried out below a fiftieth of critical micelle concentration (cmc) of SDS, where all added amounts of SDS are adsorbed on the TiO₂ particles. The stability of the Pickering emulsions incorporating TiO₂ suspensions pre-adsorbed SDS was investigated by measuring the volume fraction of emulsified silicone oil, adsorbed amounts of TiO₂ suspensions pre-adsorbed SDS, oil droplet size, and some rheological responses such as the stress-strain sweep curve and strain and frequency dependences of dynamic viscoelastic moduli. The silicone oil was almost emulsified by TiO₂ suspensions pre-adsorbed SDS above cmc/10³. Increasing in the adsorbed amount of SDS on the TiO₂ particles leads to an increase in the adsorbed amounts of TiO₂ suspensions pre-adsorbed SDS. Such silicone oil emulsions for the first time showed two yield stresses in the stress-strain sweep curve as well as the oscillatory stress-strain curve. The respective yield stresses also increase with an increase in the adsorbed amounts of TiO₂ suspensions pre-adsorbed SDS. From such characteristic rheological properties and a partial sedimentation of some TiO₂ particles remained in the dispersion medium, we proposed the formation of a three dimensional network of the flocculated TiO₂ particles pre-adsorbed SDS on the silicone oil droplets.     

Synthesis and characterization of metal substituted AlxCr1−x(acetylacetonate)3 single-source precursors for their application to MOCVD of thin films

A detailed study, involving the synthesis of a single-source precursor containing two metal ions sharing the same crystallographic site, has been undertaken to elucidate the use of such a single-source precursor in a CVD process for growing thin films of oxides comprising these two metals, ensuring a uniform composition and distribution of metal ions. The substituted complexes Cr_1−xAl_x(acac)₃, where acac = acetylacetonate, have been prepared by a co-synthesis method, and characterized using UV–Vis spectroscopy, TGA/DTA measurements, and single crystal X-ray diffraction at low temperature. All the studied compositions crystallize in the monoclinic space group P2₁/c with Z = 4 in the unit cell. It was observed that the ratio (Al:Cr) of the site occupancy for the metal ions, obtained from single crystal refinement, is in agreement with the results obtained from complexometric titrations. All the solid state structures have the metal in an octahedral environment forming six-membered chelate rings. M–O acac bond lengths and disorder in the terminal carbon have been studied in detail for these substituted metal–organic complexes. One composition among these was chosen to evaluate their suitability as a single-source precursor in a LPMOCVD process (low-pressure metal–organic chemical vapour deposition) for the deposition of a substituted binary metal oxide thin film. The resulting thin films were characterized by X-ray diffraction, scanning electron microscopy, and infrared spectroscopy.     

Bi2WO6 photocatalytic films fabricated by layer-by-layer technique from Bi2WO6 nanoplates and its spectral selectivity

Bi₂WO₆ multilayer films have been fabricated successfully by a layer-by-layer (LbL) technique from Bi₂WO₆ nanoplates, which show higher visible-light photoactivity (λ>420 nm) than that of Bi₂WO₆ nanoplate powders and P25 TiO₂ films. The films were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and UV-visible absorption spectroscopy. Photocatalytic activities of the films were evaluated by the rhodamine B (RhB) decomposition under UV and visible-light irradiation. Thickness and photoactivity of the film can be modified easily by changing the deposition cycles. Bi₂WO₆ films have the spectral selectivity of the photocatalytic degradation of RhB. Under the wavelength greater than 300 nm, the RhB molecules tend to be transformed to rhodamine over Bi₂WO₆ films selectively. However, in the case of shorter wavelength (λ=254 nm) light irradiation, the RhB molecules can be photodegraded completely.     

Low-temperature, solution processing of TiO2 thin films and fabrication of multilayer dielectric optical elements

High-quality TiO₂ thin films have been deposited from aqueous titanium-peroxo solutions via spin coating. The effects of precursor solution pH on the crystallization behavior, morphology, density, and refractive index of the films are reported. From X-ray diffraction measurements, the amorphous as-deposited films are found to crystallize in the anatase phase at 250 °C. Surface and cross-section SEM images reveal that films deposited from an acidic precursor are more uniform and denser than those deposited from a basic precursor. X-ray reflectivity measurements show that films with smooth surfaces and high densities (up to 87% of single-crystal anatase) can be produced at temperatures as low as 300 °C. Measured densities are consistent with high refractive indices at 633 nm of 2.24 and 2.11 for films derived from acidic and basic precursors, respectively. The uniformity and dense nature of the films have allowed fabrication of multilayer dielectric optical elements with thermal processing at only 300 °C. The distributed Bragg reflector with four bilayers exhibits a reflectance of 92% and a stop band width of 150 nm. The optical microcavity has a quality factor of 20. The optical properties of all elements agree well with theoretical models, indicating good optical quality. Use of the precursor chemistry for direct photopatterning of TiO₂ films without a polymer resist is also demonstrated.     

Influences of Solvent on Properties of TiO<Subscript>2</Subscript> Porous Films Prepared by a Sol-Gel Method from the System Containing PEG

Ethanol, n-butanol, mixed ethanol/terpineol and ethanol/1-decanol were used as the solvents to prepare porous TiO₂ films by the sol-gel method from the system containing tetrabutylorthotitanate as starting material and PEG as a template. The comparison of effects of the four solvents on the porous structure, film thickness, crystallization behavior from amorphous to anatase and optical properties of the resultant TiO₂ porous films are discussed. The maximum thickness of the film prepared by one-run dip-coating reaches over 1.17 μm when 1-decanol is used as the solvent. The mechanism for formation of the porous structure is interpreted based on the phase separation and self-assembly of PEG in the sol systems.     

Synthesis of titanate, TiO2 (B), and anatase TiO2 nanofibers from natural rutile sand

Titanate nanofibers were synthesized by hydrothermal method (150 °C for 72 h) using natural rutile sand as the starting materials. TiO₂ (B) and anatase TiO₂ (high crystallinity) nanofibers with the diameters of 20-100 nm and the lengths of 10-100 μm were obtained by calcined titanate nanofibers for 4 h at 400 and 700 °C (in air), respectively. The samples characterized by XRD, SEM, TEM, SAED, HRTEM, and BET surface area. This synthesis method provides a simple route to fabricate one-dimensional nanostructured TiO₂ from low cost material.     

TiO2/carbon nanotube hybrid nanostructures: Solvothermal synthesis and their visible light photocatalytic activity

MWCNT/TiO₂ hybrid nanostructures were prepared via solvothermal synthesis and sol-gel method with benzyl alcohol as a surfactant. As-prepared hybrid materials were characterized by X-ray diffraction, transmission electron microscopy, UV-vis diffuse reflectance spectra and X-ray photoelectron spectroscopy. The results showed that MWCNTs were uniformly decorated with anatase nanocrystals in solvothermal condition, but MWCNTs were embedded in a majority of TiO₂ nanoparticles by sol-gel method. When the weight ratio of MWCNTs to TiO₂ was 20%, MWCNT/TiO₂ hybrid nanostructures prepared by solvothermal synthesis exhibited higher visible-light-driven photocatalytic activity than that prepared by sol-gel method. Post-annealing of MWCNT/TiO₂ nanostructures at 400 °C resulted in the formation of the carbonaceous Ti-C bonds on the interface between TiO₂ and MWCNTs, which enhanced the photoabsorbance of the hybrid materials in the visible light region and improved the visible-light degradation efficiency of methylene blue.     

Formation and performances of porous InVO4 films

Porous complex oxide films consisting of preferentially orientated orthorhombic phase of InVO₄ have been prepared using a novel simple method by pyrolysis of amorphous complex precursor. The formation and controlling of porous InVO₄ films can be easily obtained by modifying the calcination temperature. The pure orthorhombic InVO₄ phase can be obtained at a relatively lower temperature (500 °C), and the films are preferential orientation of the (200) face parallel to the substrate. The phase separation mechanism was suggested for the formation of porous films. Under visible light irradiation (λ>400 nm), porous InVO₄ films have shown the photocatalytic activity for photodegradation of gaseous formaldehyde, and can generate photocurrent. The electrochemical properties of the films with different crystal structure and pore structure were also investigated.     

Preparation and characterization of SiO2/TiO2 composite microspheres with microporous SiO2 core/mesoporous TiO2 shell

SiO₂/TiO₂ composite microspheres with microporous SiO₂ core/mesoporous TiO₂ shell structures were prepared by hydrolysis of titanium tetrabutylorthotitanate (TTBT) in the presence of microporous silica microspheres using hydroxypropyl cellulose (HPC) as a surface esterification agent and porous template, and then dried and calcined at different temperatures. The as-prepared products were characterized with differential thermal analysis and thermogravimetric (DTA/TG), scanning electron microscopy (SEM), X-ray diffraction (XRD), nitrogen adsorption. The results showed that composite particles were about 1.8 μm in diameter, and had a spherical morphology and a narrow size distribution. Uniform mesoporous titania coatings on the surfaces of microporous silica microspheres could be obtained by adjusting the HPC concentration to an optimal concentration of about 3.2 mmol L⁻¹. The anatase and rutile phase in the SiO₂/TiO₂ composite microspheres began to form at 700 and 900 °C, respectively. At 700 °C, the specific surface area and pore volume of the SiO₂/TiO₂ composite microspheres were 552 and 0.652 mL g⁻¹, respectively. However, at 900 °C, the specific surface area and pore volume significantly decreased due to the phase transformation from anatase to rutile.