端羟基聚丙烯酸酯改性水性聚氨酯

将丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)通过溶液自由基聚合,用巯基乙醇作为链转移剂调控合成了一定分子量的端羟基聚丙烯酸酯(PA),再与聚氨酯(PU)预聚体反应,在水中分散得到PA-PU-PA三嵌段共聚复合乳液。 采用FTIR和¹HNMR测试技术对共聚物结构进行了表征。 结果表明,随着PU与PA质量比的降低,共聚物中丙烯酸酯含量随之增加;PU软硬链段之间的氢键化作用减弱。 TEM显示,复合乳胶粒子形态均匀规整,并呈现明显的核壳结构。改性后的乳胶膜耐水、耐热性能均随着PU/PA质量比的减小而提高,吸水率由25%降低至5%,最大热失重温度由369 ℃提高至432 ℃。     

丁苯、丁腈基聚氨酯的形态与性能

用示差扫描量热法 (DSC)、红外分光光度计 (FTIR)和原子力显微镜 (AFM)研究了端羟基聚丁二烯 苯乙烯共聚物 (HTBS)、端羟基聚丁二烯 丙烯腈共聚物 (HTBN)和端羟基聚丁二烯 (HTPB)与甲苯二异氰酸酯、1 ,4 丁二醇构成的溶液法聚二烯烃基聚氨酯 (PU)的形态结构 .结果表明HTPB和HTBS基PU的相分离程度很大 ,而HTBN基PU的相分离程度小 .这可能归因于HTBS软段的极性低 ,不能与硬段形成氢键 ,而HTBN软段中的腈基具有很强的极性 ,且可以与硬段形成氢键作用 ,增加了软硬段间的相容性 ,相分离程度明显降低 .AFM表明HTBN PU随着硬段含量提高 ,表面粗糙度增大 ,由软段为连续相逐渐过渡到双连续结构 .在硬段含量 6 3%时 ,HTBN和HTPB基PU均呈双连续结构 ,而HTBS PU中硬段为连续相 .HTBN PU软段的相区尺寸在1 2nm左右 ,表面粗糙度较大 ,HPBS PU软段的相区尺寸在 1 1nm左右 ,表面粗糙度最小 ,HTPB PU存在 1 4nm和 5 0nm大小不等的软段相区尺寸 .力学性能表明 ,在软段中引入苯乙烯和丙烯腈结构 ,可使聚氨酯抗张强度分别提高 1 5和 2倍 ,模量和断裂伸长率也明显提高     

具有超支化结构的聚醚型脂肪族聚氨酯弹性体的合成与表征及力学性能研究

用聚四氢呋喃醚二醇、端羟基超支化聚酯(HB-20)、异佛尔酮二异氰酸酯和1,4-丁二醇,合成了含有超支化结构的聚醚型脂肪族聚氨酯(PU)弹性体.通过Flory-Rehner公式计算了体系的交联密度;用FT-IR、WAXD和DSC表征了超支化PU的氢键化程度和形态.实验结果表明,在PU弹性体中引入少量的HB-20,能提高氨基甲酸酯羰基的氢键化程度和软硬段间的微相分离程度,从而显著提高材料的拉伸强度.由于氢键化程度和交联密度双重效应的影响,含6 wt%HB-20的聚醚型PU与不含HB-20的PU相比拉伸强度提高了2倍多,达到37.9 MPa,断裂伸长率仍高达414%.     

用FTIR研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用溶液法得到线形多嵌段聚氨酯（PU）与聚氯乙烯（PV）、氯化聚氯乙烯（CPVC）的共混物。用FTIR研究PU/PVC、PU／CPVC共混物的相容性，发现PVC、CPVC的加入破坏了PU中原来的氢键，并且PU中的炭基（C=0）与PVC、CPVC中的α－H形成了新的氢键，因而说明了PU／PVC、PU／CPVC共混物具有良好的相容性。     

乙烯-丙烯酸共聚物非晶区结构和分子运动的固体核磁共振研究

利用固体高分辨1 3CCP MAS和变温固体质子宽线技术对乙烯 丙烯酸共聚物 (EAA)非晶区的结构和分子运动进行了研究 ,结果发现 ,非晶区中羧基之间可以形成氢键 ,其数量随着共聚物中丙烯酸共聚单体含量的增加而增加 ,使得共聚物中非晶区分子运动能力随非晶区相对含量的增加而减弱 ,这是一种与一般的乙烯共聚物相反的变化趋势 .通过交叉极化方法间接测量了非晶区中乙烯链段的1 H自旋 自旋弛豫时间 (T2 ) ,表明非晶区中乙烯链段的运动同样受到氢键的束缚 .随着温度的升高 ,羧基之间的氢键发生解离 ,非晶区的柔性增强     

聚氨酯/Al2O3纳米复合材料的制备和性能

采用原位聚合法制备聚氨酯(PU)/Al2O3纳米复合材料.DSC和FT-IR测试结果表明:PU/Al2O3纳米复合材料中的氨酯羰基氢键化程度和硬段的有序化程度较纯PU低,且PU软硬段间有更好的相混合程度;TEM照片显示:Al2O3以纳米尺寸较均匀地分散在PU体系中,且纳米Al2O3粒子与PU基体有较强的界面作用;力学性能测试结果表明:少量纳米Al2O3粒子的加入,对PU材料有很好的增强和增韧效果.     

溶剂在丁腈基聚氨酯中的溶解和扩散

用石英弹簧法和示差扫描量热法 (DSC)、红外分光光度计 (FTIR)研究了苯、乙醇、丙酮、醋酸乙酯和1,2 二氯乙烷五种溶剂在端羟基聚丁二烯 丙烯腈共聚物为软段的聚氨酯中的溶解和扩散行为 .结果表明所有溶剂在丁腈聚氨酯中的扩散均为非费克扩散 ,且随着溶剂蒸汽压增大偏离费克扩散的程度增大 .相同相对蒸汽压下 1,2 二氯乙烷和醋酸乙酯偏离费克 (Fickian)扩散的程度较大 ,而乙醇、丙酮和苯则较小 ,这主要与它们和丁腈软段溶解度参数的极性分量和氢键分量有关 .1,2 二氯乙烷和苯在HTBN PU中的溶解度较高 ,而乙醇 ,醋酸乙酯和丙酮较低 ,主要与它们和丁腈软段溶解度参数的色散分量有关 .所有溶剂均表现出近似Flory Huggins型等温吸收曲线 .红外表明吸收溶剂后 ,氨基甲酸酯基团的氢键化程度有不同程度的下降 ,和溶剂与之形成氢键的能力大小有关 .力学性能表明非极性溶剂苯对材料的力学性能影响较小 ,而乙醇 ,醋酸乙酯和丙酮由于可与氨酯基团形成氢键 ,对原HTBN PU中氨酯键氢键的破坏大 ,力学性能下降大     

用DSC研究线形多嵌段聚氨酯与聚氯乙烯、氯化聚氯乙烯共混相容性

用示差扫描量热法（DSC）研究了线形多嵌段聚氨酯（PU）与聚氯乙烯（PVC）、氯化聚氯乙烯（CPVC）共混相容性，说明了PU／VC、PU／CPVC的相容是由于共混物中形成了新的氢键的缘故．聚酯型聚氨酯与PVC、CPVC的相容性要好子聚酸型聚氨酯，CPVC与PU的相容性又要好于PVC．聚氨酯中硬段的引入不利于PU／PVC、PU／CPVC的相容性．     

PAA/PU合金制备多孔PI薄膜及结构与性能研究

以N,N-二甲基乙酰胺(DMAc)为溶剂, 在聚氨酯(PU)溶液中使均苯四酸二酐(PMDA)与4,4′-二氨基二苯醚(4,4′-ODA)缩聚成聚酰亚胺(PI)预聚体聚酰胺酸(PAA), 从而制成PAA/PU的混合溶液, 然后刮涂成膜, 经过热处理使得PAA亚胺化和PU降解, 制备多孔PI薄膜. 通过对薄膜进行红外光谱,热失重分析及透射电镜(TEM)观察, 结果表明, 最佳的PU热降解温度为360 ℃, PU降解后在PI基体中留下长条状纳米孔, 且孔径大小随聚氨酯含量的增加而增大. 通过对薄膜进行力学性能、 介电性能和吸水率研究, 结果表明, 随着体系中PU用量的增加, 热处理后的多孔PI薄膜的介电常数逐渐下降, 但拉伸强度降低, 吸水率上升.     

反应注射成型聚氨酯互穿聚合物网络研究——刚性网络对于体系形态及性能的影响

用微型反应注射成型机制备了以聚氨酯(PU)为弹性相的两类同步互穿聚合物网络(SIN),其刚性相分别采用保留仲羟基的乙烯基酯树脂(VERH)以及封闭仲羟基的乙烯基酯树脂(VERA)。用傅里叶变换红外光谱在线跟踪了这类互穿网络的生成过程,发现刚性网络抑制了PU网络中硬段有序结构的形成,两个网络间有一定程度的互穿,而两个网络间的化学键作用进一步削弱氢键强度。自旋—自旋弛豫时间的测定进一步表明网络间存在一定的互穿以及刚性相对于PU硬段结晶的抑制作用。材料的力学性能与其SIN的形态有关。VERA网络对PU表现出明显的增强作用,而由VERH网络形成的SIN则由于体系相分离进程受到严重阻碍而使材料性能恶化。     

Corrosion inhibition performance of tannins for mild steel in hydrochloric acid solution

Research on Chemical Intermediates - The corrosion inhibition behavior of commercial hydrolysable tannin (tara tannin), condensed tannin (black wattle tannin) and complex tannin (bayberry tannin)...     

Properties of poly(lactic acid-co-glycolic acid) film modified by blending with polyurethane

A number of poly(lactic acid-co-glycolic acid)/polyurethane (PLGA/PU) blend films with various PU mole contents were prepared by casting the polymer blend solution in chloroform. The surface morphologies of the PLGA/PU blend films were studied by scanning electron microscopy (SEM). The thermal, mechanical and chemical properties of the PLGA/PU blend films were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile tests and surface contact angle tests. The results revealed that the introduction of PU could markedly modify the properties of PLGA films.     

应用单宁与淀粉为交联剂改性聚氨酯

通过植物原料单宁与淀粉对聚氨酯的改性可提高聚氨酯的机械性能和热性能 ,单宁成分的导入还能有效提高聚氨酯交联点密度、组分相容性和体系的形态结构均匀性 .当单宁的含量占投入的植物原料的6 0wt%时 ,单宁和淀粉聚氨酯网络互相贯穿表现出良好的相容性 ,其拉伸强度、杨氏模量分别提高到 5 1 9MPa和 30 8 4MPa ,积分程序分解温度达到 375℃ .同时单宁成分有望在一定范围内调节聚氨酯的降解速度 .     

Thermal,mechanical, and morphological properties of soybean oil-based polyurethane/epoxy resin interpenetrating polymer networks (IPNs)

A series of interpenetrating polymer networks (IPNs) based on epoxy (EP) resin and polyurethane (PU) prepolymer derived from soybean oil-based polyols with different mass ratios were synthesized. The structure, thermal properties, damping properties, tensile properties, and morphology of soybean oil-based PU/EP IPNs were characterized by Fourier-transform infrared spectroscopy, differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), universal test machine, and scanning electron microscopy (SEM). DSC and DMA results show that the glass transition temperature of the soybean oil-based PU/EP IPN decreases with the increase of PU prepolymer contents. Soybean oil-based PU/EP IPNs have better damping properties than that of the pure epoxy resin. The tensile strength and modulus of PU/EP IPNs decrease, while elongation at break increases with the increase of PU prepolymer contents. SEM observations reveal that phase separation appears in PU/EP IPNs with higher PU prepolymer contents.     

Fabrication of graphene‐silver/polyurethane nanofibrous scaffolds for cardiac tissue engineering

The graphene‐based nanocomposites are considered as great candidates for enhancing electrical and mechanical properties of nonconductive scaffolds in cardiac tissue engineering. In this study, reduced graphene oxide‐silver (rGO‐Ag) nanocomposites (1 and 2 wt%) were synthesized and incorporated into polyurethane (PU) nanofibers via electrospinning technique. Next, the human cardiac progenitor cells (hCPCs) were seed on these scaffolds for in vitro studies. The rGO‐Ag nanocomposites were studied by X‐ray diffraction (XRD), Raman spectroscopy, and transmission electron microscope (TEM). After incorporation of rGO‐Ag into PU nanofibers, the related characterizations were carried out including scanning electron microscope (SEM), TEM, water contact angle, and mechanical properties. Furthermore, PU and PU/nanocomposites scaffolds were used for in vitro studies, wherein hCPCs showed good cytocompatibility via 3‐(4, 5‐dimethylthiazol‐2‐yl)‐2,5‐diphenyl tetrazolium bromide (MTT) assay and considerable attachment on the scaffold using SEM studies. Real‐time polymerase chain reaction (PCR) and immunostaining studies confirmed the upregulation of cardiac specific genes including GATA‐4, T‐box 18 (TBX 18), cardiac troponin T (cTnT), and alpha‐myosin heavy chain (α‐MHC) in the PU/rGO‐Ag scaffolds in comparison with neat PU ones. Therefore, these nanofibrous rGO‐Ag–reinforced PU scaffolds can be considered as suitable candidates in cardiac tissue engineering.     

Recovery of Th(IV) from aqueous solution by reassembled collagen-tannin fiber adsorbent

A novel adsorbent, collagen immobilized tannin adsorbent (CITA), was prepared and its adsorption behaviors to Th(IV) were investigated. CITA was in fibrous state due to the reassembly of collagen molecules by the inducement of tannin. This adsorbent loaded a greater amount of tannin and exhibited higher adsorption capacity to Th(IV) than the tannin immobilized adsorbent prepared from collagen fiber. The adsorption of CITA to Th(IV) is mainly attributed to surface complexation, which is a pH- rather than an ionic strength-dependent process. The adsorption kinetics and isotherms were described by pseudo-second-order rate model and Freundlich equation, respectively. Column adsorption studies indicated that CITA is available for effectively recovering Th(IV) from aqueous solution.     

氨基硅油扩链改性水性聚氨酯的研究

通过将由甲苯二异氰酸酯与聚四氢呋喃,二羟甲基丙酸反应制得的聚氨酯预聚体在低浓度氨基硅油的水乳液中扩链,合成了一种硅氧烷改性的聚氨酯水乳液,并用傅立叶红外光谱,ＥＳＣＡ能谱,接触角仪,电子拉力试验机,吸水率测定及乳液稳定性测试对其进行研究。     

植物多酚在高分子材料中的应用

植物多酚类物质又叫单宁,是一类多羟基酚类化合物,具有良好的生物相容性和可降解性;由于多元酚的结构赋予了一系列独特的性质.植物多酚不但可以与醛类物质发生缩聚反应,还可以通过氢键、疏水键或者共价键与众多高分子化合物接枝、共聚或共混制备出新型的功能高分子材料.基于文献,对植物多酚在高分子材料,比如:聚氨酯、酚醛树脂、聚酯和一些天然高分子中的应用,如:增加高分子材料的抗菌、可降解以及抗氧化性等性能进行了综述.     

Study on thermal properties of polyurethane nanocomposites based on organo-sepiolite

The effects of sepiolite modified with γ-aminopropyltriethoxylsilane (KH550-Sp) on thermal properties of polyurethane (PU) nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TG), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), and tensile test. The DSC results showed that the glass transition temperature of hard segments in PU/KH550-Sp nanocomposite increased with the increase of KH550-Sp, because sepiolite restricted the formation of hydrogen bonding within hard segments of polyurethane. TG results revealed that the thermal stability of PU was improved by KH550-Sp, and the onset decomposition temperature for PU nanocomposites with a KH550-Sp content of 3 wt% was about 20 °C higher than that for pure PU. The tensile properties of pure PU and nanocomposites before and after ageing 120 °C for 72 h were determined, and it was observed that the percentage loss in tensile strength decreased with the addition of KH550-Sp because of an oxidation barrier of KH550-Sp confirmed by ATR-FTIR.     

聚氨酯/蒙脱土纳米复合材料的制备与性能研究

纳米复合材料由于其纳米尺寸效应 ,表面效应以及纳米粒子与基体界面间强的相互作用 ,具有优于相同组分常规复合材料的力学 ,热学等性能 ,引起了人们的广泛关注 .用纳米材料改性聚合物 ,制备纳米复合材料是获得高性能高分子复合材料的重要方法 ,采用较多的是插层复合法 ,可分为两类 ,一是单体预先插层于层状结构填料的晶片层间 ,然后聚合 ;二是聚合物溶液或熔体直接插层于层状结构填料的晶片层间 .聚氨酯 (PU)是由多异氰酸酯与多元醇通过加聚反应而形成的高聚物 ,其重复结构单元是氨基甲酸酯链段( R2 OCONHR1NHCOO) .PU弹性体具有耐磨…