Friction and wear of rare earths modified carbon fibers filled PTFE composite under dry sliding condition

Carbon fibers (CF) were surface treated with air-oxidation and rare earths (RE), respectively. The friction and wear properties of polytetrafluoroethylene (PTFE) composites filled with differently surface treated carbon fibers, sliding against GCr15 steel under dry sliding condition, were investigated on a block-on-ring M-2000 tribometer. Experimental results revealed that RE treatment largely reduced the friction and wear of CF reinforced PTFE (CF/PTFE) composites. The RE treated composite exhibited the lowest friction and wear under dry sliding. Scanning electron microscopy (SEM) investigation of worn surfaces and transfer films of CF/PTFE composites showed that RE treated CF/PTFE composites had the smoothest worn surface under given load and sliding speed, and a continuous and uniform transfer film formed on the counterface. X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the oxygen concentration was obviously increased after RE treatment, and more carboxyl groups were introduced onto CF surfaces after RE treatment. The increase in the amount of oxygen-containing groups increased the interfacial adhesion between CF and PTFE matrix, and accordingly increased the tribological properties of the composite.     

Effect of Carbon Fiber Surface Oxidation on Tribological Properties of PTFE Composite under Oil-Lubricated Conditions

Air-oxidation and ozone surface treatment of carbon fibers (CF) on tribological properties of CF reinforced polytetrafluoroethylene (PTFE) composites under oil-lubricated conditions was investigated. Experimental results revealed that ozone treated CF reinforced PTFE (CF/PTFE) composite had the lowest friction coefficient and wear under various applied loads and sliding speeds compared with untreated and air-oxidated composites. X-ray photoelectron spectroscopy (XPS) study of the carbon fiber surface showed that, after ozone treatment, oxygen concentration was obviously increased, and the amount of oxygen-containing groups on CF surfaces were increased greatly. The increase in the amount of oxygen-containing groups enhanced interfacial adhesion between CF and PTFE matrix, and large scale rubbing-off of PTFE was prevented; therefore, the tribological properties of the composite were improved.     

The effect of surface treatment of carbon fiber on the flexural property of thermoplastic polyimide composite

Rare earth solution (RES) surface modification and air-oxidation methods were used to improve the interfacial adhesion of the carbon fiber reinforced polyimide (CF/PI) composite. The flexural property of the PI composites reinforced by the carbon fibers treated with different surface modification methods was comparatively investigated. Results showed that the flexural strength of CF/PI composite was improved after RES treatment. The improvement of impact and flexural property of the CF/PI composite was mainly due to the improvement in interfacial adhesion after RES treatment. X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the oxygen concentration was obviously increased after RES treatment. The increase in the amount of organic functional groups increased the interfacial adhesion between CF and PI matrix.     

Effects of carbon fiber surface treatment on the tribological properties of 2D woven carbon fabric/polyimide composites

Polyacrylonitrile (PAN)-based carbon fabric (CF) was modified with strong HNO₃ oxidation and then introduced into polyimide (PI) composites. The friction and wear properties of the carbon fabric reinforced polyimide composites (CFRP), sliding against GCr15 stainless steel rings, were investigated on an M-2000 model ring-on-block test rig under dry sliding. Experimental results revealed that the carbon fiber surface treatment largely reduced the friction and wear of the CFRP. Compared with the untreated ones, the surface-modified CF can enhance the tribological properties of CFRP efficiently due to the improved adhesion between the CF and the PI matrix. Scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS) study of the carbon fiber surface showed that the fiber surface became rougher and the oxygen concentration increased greatly after surface treatment, which improved the adhesion between the fiber and the PI matrix and improved the friction-reduction and anti-wear properties of the CFRP. An erratum to this article can be found at     

Influence of carbon fiber’s surface state on interlaminar shear properties of CFRP laminate

In order to investigate the influence of carbon fiber’s surface state on the interlaminar shear properties of carbon fiber-reinforced plastic (CFRP) laminate, the carbon fiber’s surface state was modified by thermal treatment at elevated temperatures. The interlaminar shear strength (ILSS) of CFRP laminates reinforced with treated fibers was measured by means of short-beam shear test, and the surface state of fiber was characterized by Electron Spectroscopy for Chemical Analysis (ESCA) analysis to reveal the dominate factor for controlling the ILSS. Combining the ILSS measurement with the ESCA analysis, the results indicated that: (1) the ILSS is strongly dependent on the oxygen-containing functional groups on the surface of carbon fiber; (2) the fiber treated at 600?°C has the highest oxygen-containing functional groups that lead to the highest ILSS of CFRP; and (3) at temperatures beyond 600?°C, the oxygen-containing functional groups decrease with increasing the heat treatment temperature, resulting in a low ILSS of CFRP laminates. Furthermore, from the microstructure observation, it was found that the CFRP mainly failed in the mode of multi-interlaminar shear. The multi-interlaminar shear failure in the CFRP laminates with low ILSS is more severe due to a weak fiber-matrix interface.     

Carbon fiber/epoxy composite materials cured thermally and with microwave irradiation

In this paper, composite materials of short carbon fibers (CFs) and a thermosetting epoxy were prepared in three different ways: without curing, thermal curing, and thermal curing followed by microwave irradiation. Mechanical properties of the three kinds of CF reinforced plastic (CFRP) composites were studied to explore the effect of microwave irradiation. Microscopic study with the aid of a scanning electron microscope (SEM) was performed on fractured composite surfaces to identify the principle features of failure. Degree of polymerization of the epoxy resin in the three CFRP composites was evaluated by infrared (IR) spectroscopy. The microwave irradiated CFRP exhibited mechanically ductile behavior even though its highest degree of polymerization. Use of microwaves and resultant stronger physico-chemical linkage at the interface between CF and epoxy resin are the main feature of this study.     

Surface treatment of CFRP composites using femtosecond laser radiation

In the present work, we investigate the surface treatment of carbon fiber-reinforced polymer (CFRP) composites by laser ablation with femtosecond laser radiation. For this purpose, unidirectional carbon fiber-reinforced epoxy matrix composites were treated with femtosecond laser pulses of 1024 nm wavelength and 550 fs duration. Laser tracks were inscribed on the material surface using pulse energies and scanning speeds in the range 0.1–0.5 mJ and 0.1–5 mm/s, respectively. The morphology of the laser treated surfaces was investigated by field emission scanning electron microscopy. We show that, by using the appropriate processing parameters, a selective removal of the epoxy resin can be achieved, leaving the carbon fibers exposed. In addition, sub-micron laser induced periodic surface structures (LIPSS) are created on the carbon fibers surface, which may be potentially beneficial for the improvement of the fiber to matrix adhesion in adhesive bonds between CFRP parts.     

Fiber-matrix adhesion mechanism of pitch-based carbon fiber composites

The fiber-matrix adhesion mechanism in high modulus pitch-based carbon fiber-epoxy matrix composites has been studied. The surface morphology and chemistry of the carbon fibers were examined by microscopic (SEM, STM), thermodynamic and spectroscopic (XPS, Raman) techniques. The interlaminar shear strength and transverse tensile strength of the composites made from surface-treated and untreated fibers were also obtained. In the microscopic analysis, there was no difference in the surface roughness between the surface-treated and untreated fibers. In the thermodynamic and spectroscopic analyses, surface treatment of the carbon fibers increased the amount of surface oxygen. The results indicated that the major role of the surface treatment on the carbon fiber-epoxy resin adhesion is not the mechanical interlocking effect by the surface roughness. The formation of surface oxygen-containing functional groups is assumed to account for the increase in fiber-matrix interfacial adhesion.     

Influence of Fiber Surface Treatment on Mechanical Properties of CF/PET Composites

Carbon fiber (CF) / poly (ethylene terephthalate) (PET) composites were prepared with various contents (2–15wt%) of short carbon fibers. To investigate the effect of surface treatment of the CF on the mechanical properties of the composites, three specimens were prepared; those with short carbon fibers (called SCF), short carbon fibers oxidized with nitric acid (called NASCF) and the fibers oxidized with nitric acid and treated with silane coupling agent (called SCSCF). Flexural, tensile and impact tests were performed to observe mechanical behavior of the specimens. The morphology of the specimens was also studied with a scanning electron microscope (SEM). SCSCF composite had better mechanical properties than the other composites with the same content of carbon fibers since the coupling agent resulted in better interfacial adhesion between the fiber and the matrix.     

Study on the surface properties of wood/polyethylene composites treated under plasma

Wood/polyethylene (PE) composites are widely used in many fields for its excellent properties, but they are hard to adhere for the surface lacking of polarity. So low-pressure glow discharge of air plasma was used to improve the adhesion properties of wood/PE composites. The composites were treated by plasma under different discharge power. And the changes on the surface properties of the treated and untreated composites were studied by contact angle, Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS) analysis. The measurement showed that the contact angle decreased after plasma treatment, and the contact angle decreased gradually with the increasing of discharge power. The FTIR analysis results showed that the polar groups such as hydroxyl, carbonyl and carboxyl were formed on the surface of the composites treated under plasma. SEM and AFM results showed that the roughness of plasma treated samples increased. XPS analysis results indicated that the content of carbon element decreased while the content of oxygen element in the composition of wood/PE composites surface element increased and it reached a balance in a higher power, meanwhile a lot of carboxyl groups were formed. The newly formed polar groups are benefit for the adhesion of composites. The shear bonding strength test showed that the adhesion properties of wood/PE composites improved effectively after plasma treatment.     

Influence of γ-ray radiation grafting on interfacial properties of aramid fibers and epoxy resin composites

This research used Co⁶⁰ γ-ray radiation to modify Armos fibers in 1,2-epoxy-3-chloropropane. After the treatment, the interlaminar shear strength (ILSS) values of aramid/epoxy composites were improved by about 20%. Surface elements of Armos fibers were determined by XPS analysis, which indicated that the oxygen/carbon ratio was increased. The surface of the fibers treated was rougher than that of the untreated fibers when examined by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Fourier transform infrared (FT-IR) spectra confirmed that the epoxy group was grafted onto the fibers. The wettability of the fibers' surface was also enhanced by the treatment. Nanoindentation technique analysis showed that the nanohardnesses of the various phases (the fiber, the interface and the matrix) in the composite, whose fibers were treated, were correspondingly higher than those in the composite, whose fibers were untreated. The results indicate that γ-ray irradiation grafting technique, which is a suitable batch process for industrialization, can modify the physicochemical properties of Armos fibers and improve the interfacial adhesion of its composite.     

The effect of interphase modification on carbon fiber/polyarylacetylene resin composites

Interfacial modification for carbon fiber (CF) reinforced polyarylacetylene (PAA) resin, a kind of non-polar, was investigated. The high carbon phenolic resin was used as coating to treat the surface of CF after oxidation. Atomic force microscopy (AFM) with force modulation mode was used to analyze the interphase of composite. The interlaminar shear strength (ILSS) and mechanical properties of CF/PAA composites were also measured. It was found that the CF/PAA composites treated with oxidation and coating after oxidation had transition area between carbon fiber and PAA resin. The existence of transition area led to the improvement of interfacial performance of composites. Specially, the thickness and stiffness of interphase of composite treated with coating after oxidation were more suitable for CF/PAA composites. Thus, the composite treated with coating after oxidation had the highest value of ILSS and the best mechanical properties.     

Roles of interfaces between carbon fibers and epoxy matrix on interlaminar fracture toughness of composites

The effect of atmospheric-pressure plasma treatment on high strength PAN-based carbon fibers had been studied in terms of fiber surface energetics and mode I and II interlaminar fracture toughness of unidirectional carbon fibers/epoxy matrix composites. The surface characterization of plasma treated carbon fibers was investigated by X-ray photoelectron spectroscopy (XPS) and contact angles. As a result, the plasma treatment changed the surface properties of the carbon fibers, mainly through formation of oxygen functional groups like hydroxyl, carbonyl, and carboxyl groups. According to contact angle measurements, it was observed that plasma treatment led to an increase in surface free energy of the fibers, mainly due to the increase of its specific component. Fracture toughness test results employing double-cantilever beam (DCB) and end notched flexure (ENF) specimens also showed that the increase in specific components or hydrogen bonding between the –OH groups on carbon fibers and the =O ring in epoxy matrix resins played an important role in improving the degree of adhesion at interfaces, resulting in an increase in the interfacial fracture toughness of the composites studied.     

Enhanced interfacial adhesion between PMMA and carbon fiber by graphene oxide coating

The purpose of this study is to increase the interfacial properties in PMMA/carbon fiber (PMMA/CF) composites Graphene oxide (GO) and brached polyethyleneimine were coated onto the surface of carbon fiber by layer-by-layer assembly in this work. Compared with the origin PMMA/CF composite, the composites reinforced by PMMA/CF–GO showed significant enhancement in interFacial shear strength (IFSS). The improved fiber–matrix adhesion was proved by fracture morphology observation of scanning electron microscopy and almost unaffected mechanical properties of the fiber itself during the coating process. The optimal assembly time was found to be 10 for enhancing the overall composite mechanical performance.     

Surface modification of polyacrylonitrile-based carbon fiber and its interaction with imide

In this work, sized polyacrylonitrile (PAN)-based carbon fibers were chemically modified with nitric acid and maleic anhydride (MA) in order to improve the interaction between carbon fiber surface and polyimide matrix. Bismaleimide (BMI) was selected as a model compound of polyimide to react with modified carbon fiber. The surface characteristic changing after modification and surface reaction was investigated by element analysis (EA), scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and surface enhanced Raman scattering (SERS). The results indicated that the modification of carbon fiber surface with MA might follow the Diels Alder reaction mechanism. In the surface reaction between modified fibers and BMI, among the various surface functional groups, the hydroxyl group provided from phenolic hydroxyl group and bridged structure on carbon fiber may be the most effective group reacted with imide structure. The results may shed some light on the design of the appropriate surface structure, which could react with polyimide, and the manufacture of the carbon fiber-reinforced polyimide matrix composites.     

Effect of the surface roughness on interfacial properties of carbon fibers reinforced epoxy resin composites

The effect of the surface roughness on interfacial properties of carbon fibers (CFs) reinforced epoxy (EP) resin composite is studied. Aqueous ammonia was applied to modify the surfaces of CFs. The morphologies and chemical compositions of original CFs and treated CFs (a-CFs) were characterized by Atomic Force Microscopy (AFM), and X-ray Photoelectron Spectroscopy (XPS). Compared with the smooth surface of original CF, the surface of a-CF has bigger roughness; moreover, the roughness increases with the increase of the treating time. On the other hand, no obvious change in chemical composition takes place, indicating that the treating mechanism of CFs by aqueous ammonia is to physically change the morphologies rather than chemical compositions. In order to investigate the effect of surface roughness on the interfacial properties of CF/EP composites, the wettability and Interfacial Shear Strength (IFSS) were measured. Results show that with the increase of the roughness, the wettabilities of CFs against both water and ethylene glycol improves; in addition, the IFSS value of composites also increases. These attractive phenomena prove that the surface roughness of CFs can effectively overcome the poor interfacial adhesions between CFs and organic matrix, and thus make it possible to fabricate advanced composites based on CFs.     

Study on the surface performance of carbon fibres irradiated by γ-ray under different irradiation dose

The technology of high-energy irradiation is widely used in the field of material interface modification because of its high efficiency, energy conservation and environment friendliness. In this paper, γ-ray irradiation graft technology was used in order to enhance the surface performance of the carbon fibre (CF). The surface chemical elements and functional groups of untreated and irradiated CF were observed by photoelectron spectroscopy (XPS). The results show that the value of O/C and the quantity of oxygen functional groups on CF surface were enhanced efficiently after treatment by γ-ray irradiation graft technology. The morphology of CF was characterized by scanning electron microscopy (SEM) and atom forced microscopy (AFM), respectively. The surface roughness of CF was greatly increased compared with the untreated CF. Moreover, the interface performance was clearly improved after irradiation.     

Friction and Wear Behaviors of Surface-Modified Carbon Fabric/Epoxy Resin Composites

Carbon fabric (CF) was pretreated by air-plasma bombardment and then further modified by deposition of polydopamine on the surface of the pretreated CF. Epoxy resin composites reinforced by unmodified or surface-modified carbon fabric were fabricated. The friction and wear behaviors of the resulting composites were evaluated in a ring-on-block contact mode. The flexural strength and Rockwell hardness of the composites were also evaluated. The morphologies of the worn surfaces of the unmodified and modified composites were analyzed by scanning electron microscopy. The surface treatment increased the surface roughness and changed the surface topography of the CF, which contributed to enhancing the interfacial adhesion of the composites and thus improved the mechanical properties and tribo-performance. The friction and wear properties of both the unfilled and filled composites were highly dependent on the load and sliding velocity. Moreover, the results were supplemented with scanning electron micrographs to help understand the possible wear mechanisms.     

Effect of the molecular weight of sizing agent on the surface of carbon fibres and interface of its composites

The influence of different molecular weight sizing agent on the performances of carbon fibres and carbon fibres composites were studied. Three different kinds of molecular weight sizing were used. Surface composition of the fibres modified with aqueous sizing and topographies of carbon fibres surface were characterized by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and scanning electron microscope (SEM). The interlaminar shear strength and hygrothermal ageing test have been used to study the effect of fibres coatings on the adhesion of surface. The results of the study indicate that the molecular weight of sizing agent has an important influence to the carbon fibres and carbon fibres composites. The high and low molecular weight sizing agent decreased the interfacial shear strengths and hygrothermal ageing of carbon fibres composite. The moderate molecular weight of sizing agent showed an improvement of the interfacial adhesion and hygrothermal ageing.     

Improved mechanical properties of carbon fiber reinforced PTFE composites by growing graphene oxide on carbon fiber surface

The mechanical properties of carbon fiber reinforced polymer composites depend upon fiber-matrix interfacial properties. To improve the mechanical properties of ?bers/PTFE composites without sacri?cing tensile strength of ?bers, graphene oxide (GO) was introduced onto the surface of CFs by chemical vapour deposition (CVD). This hybrid coating increased the wettability and surface roughness of carbon fibers, which led to improved affinity between the carbon fibers and PTFE matrix. The resulting hybrid-coated carbon fiber-reinforced composites showed an enhancement in the short beam strength compared to un-coated carbon fiber composites. Meanwhile, a signi?cant increase of interlaminar shear strength (ILSS), interface shear strength tests (IFSS) and impact property were achieved in the 5-min-modi?ed CFs.