Access to nonisocyanate poly(thio)urethanes: A comparative study

This article describes the synthesis of new cyclic compounds able to react with amines to get nonisocyanate polyurethanes (NIPUs). The contribution of the most studied five‐membered cyclic carbonate was compared to five‐membered cyclic dithiocarbonate analogous and to a six‐membered cyclic carbonate. Difunctional reactive species were obtained by a simple substitution reaction or an efficient thiol–ene coupling reaction. The products, obtained with high yields, were characterized by 1H NMR, 13C NMR, and Fourier tansform infrared spectroscopy analysis. The dicyclocarbonates were then used to synthesize NIPUs by step growth polymerization with several diamines. These materials exhibited glass transition temperatures from 19 to ?29 °C, molar mass from 1800 to 20,400 g mol^?1, and a 20% mass loss temperature (T_d = 20%) between 249 and 296 °C. Such materials are interesting candidates for coating applications. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3284–3296     

Thiourethane‐based thiol‐ene high Tg networks: Preparation,thermal, mechanical,and physical properties

Thiourethane‐based thiol‐ene (TUTE) films were prepared from diisocyanates, tetrafunctional thiols and trienes. The incorporation of thiourethane linkages into the thiol‐ene networks results in TUTE films with high glass transition temperatures. Increases of T_g were achieved by aging at room temperature and annealing the UV cured films at 85 °C. The aged/annealed film with thiol prepared from isophorone diisocyanate and cured with a 10,080‐mJ/cm² radiant exposure had the highest DMA‐based glass transition temperature (108 °C) and a tan δ peak with a full width at half maximum (FWHM) of 22 °C, indicating a very uniform matrix structure. All of the initially prepared TUTE films exhibited good physical and mechanical properties based on pencil hardness, pendulum hardness, impact, and bending tests. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5103–5111, 2007     

Thiol–ene polymerizations using imide‐based monomers

New diene and dithiol monomers, based on aromatic imides such as benzophenone‐3,3′,4,4′‐tetracarboxylic diimide were synthesized and used in thiol‐ene polymerizations which yield poly(imide‐co‐thioether)s. These linear polymers exhibit limited solubility in various organic solvents. The molecular weights of the polymers were found to decrease with increasing imide content. The glass transition temperature (T_g) of these polymers is dependent on imide content, with T_g values ranging from ?55 °C (with no imide) up to 13 °C (with 70% imide). These thermal property improvements are due to the H‐bonding and rigidity of the aromatic imide moieties. Thermal degradation, as studied by thermogravimetric analysis, was not significantly different to the nonimide containing thiol‐ene polymers made using trimethyloylpropane diallyl ether and 3,5‐dioxa‐1,8‐dithiooctane. It is expected that such monomers may lead to increased glass transition temperatures in other thiol‐ene polymer systems as these normally exhibit low glass transition temperatures. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4637–4642     

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions as a route to well‐defined mono and bis end‐functionalized poly(N‐isopropylacrylamide)

Sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used as a facile and quantitative method for modifying end‐groups on an N‐isopropylacrylamide (NIPAm) homopolymer. A well‐defined precursor of polyNIPAm (PNIPAm) was prepared via reversible addition‐fragmentation chain transfer (RAFT) polymerization in DMF at 70 °C using the 1‐cyano‐1‐methylethyl dithiobenzoate/2,2′‐azobis(2‐methylpropionitrile) chain transfer agent/initiator combination yielding a homopolymer with an absolute molecular weight of 5880 and polydispersity index of 1.18. The dithiobenzoate end‐groups were modified in a one‐pot process via primary amine cleavage followed by phosphine‐mediated nucleophilic thiol‐ene click reactions with either allyl methacrylate or propargyl acrylate yielding ene and yne terminal PNIPAm homopolymers quantitatively. The ene and yne groups were then modified, quantitatively as determined by ¹H NMR spectroscopy, via radical thiol‐ene and radical thiol‐yne reactions with three representative commercially available thiols yielding the mono and bis end functional NIPAm homopolymers. This is the first time such sequential thiol‐ene/thiol‐ene and thiol‐ene/thiol‐yne reactions have been used in polymer synthesis/end‐group modification. The lower critical solution temperatures (LCST) were then determined for all PNIPAm homopolymers using a combination of optical measurements and dynamic light scattering. It is shown that the LCST varies depending on the chemical nature of the end‐groups with measured values lying in the range 26–35 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 3544–3557, 2009     

Photoinduced thiol–ene crosslinking of globalide/ε‐caprolactone copolymers: Curing performance and resulting thermoset properties

The increasing demand for bioderived polymers led us to investigate the potential use of the macrolactone globalide in thermoset synthesis via the photoinduced thiol–ene reaction. A series of six lipase‐catalyzed poly(globalide‐caprolactone) copolyesters bearing internal main‐chain unsaturations ranging from 10 to 50 and 100 mol % were successfully crosslinked in the melt with equal amounts of thiol groups from trimethylolpropane‐trimercapto propionate affording fully transparent amorphous elastomeric materials with different thermal and viscoelastic properties. Three major conclusions can be drawn from this study: (i) high thiol–ene conversions (>80%) were easily attained for all cases, while maintaining the cure behavior, and irrespective of functionality at reasonable reaction rates; (ii) parallel chain‐growth homopropagation of the ene monomer is insignificant when compared with the main thiol–ene coupling route; and (iii) high ene‐density copolymers result in much lower extracted sol fractions and high T_g values as a result of a more dense and homogeneous crosslinked network. The thiol–ene system evaluated in this contribution serve as model example for the sustainable use of naturally occurring 1,2‐disubstituted alkenes in making semisynthetic polymeric materials in high conversions with a range of properties. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012.     

An efficient nonisocyanate route to polyurethanes via thiol‐ene self‐addition

A novel and efficient strategy for the synthesis of nonisocyanate polyurethanes has been developed via thiol–ene self‐photopolymerization. An aliphatic thiol–ene carbamate monomer (allyl(2‐mercaptoethyl)carbamate, AMC) was synthesized by a one‐step synthesis procedure, from cysteamine and allyl chloroformate. The urethane group was therefore incorporated directly into the monomer precursor, avoiding the problems associated to toxic isocyanates. AMC was successfully stabilized with the radical inhibitor pyrogallol (1% wt). In addition, the use of phenyl phosphonic acid as coadditive allowed its stabilization for lower concentrations of pyrogallol (0.1% wt). AMC was directly transformed into thermoplastic polyurethane (TPU) through thiol–ene photopolymerization by UV‐irradiation at 365 nm. The obtained TPU presented semi‐crystalline nature and very high thermal stability (T_5% ～325 °C). It was found that high concentrations of pyrogallol decreased the reaction rate and final conversion of photopolymerization. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3017–3025     

Synthesis and Properties of Polycarbosilanes Having Lactose‐Derived Structures

A polycarbosilane having lactose‐derived structures was synthesized, and its thermal property, cytotoxicity, chemical crosslinking, and protein adsorption properties were investigated. The polycarbosilane (PSB‐Lac) was prepared by a thiol‐ene reaction between precursor poly(1‐(3‐butenyl)‐1‐methylsilacyclubane) (PSB) and heptaacetyl lactose that carried a thiol group at the anomeric position, and the successive deprotection of the acetyl groups. The lactose introduction efficiency determined by ¹H NMR measurement was 75%. TGA and DSC revealed that the polymer had a 5 wt% decomposition temperature of 260 °C and glass transition temperature (T_g) of 84 °C, which indicated that PSB‐Lac was a thermally stable polymer. PSB‐Lac had no significant cytotoxicity, which was evaluated by human liver cancer cell line HepG2 cultivation on the polystyrene dishes coated with the polymer. Urethane‐crosslinked PSB‐Lac films were prepared by casting solutions of PSB‐Lac and hexamethylene diisocyanate and heating at 120 °C after evaporation of the solvent. The crosslinked PSB‐Lac showed higher adsorption of bovine serum albumin than the similarly crosslinked polycarbosilane that had a glucose structure (PSB‐Glc). © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2420–2425     

Lignin,a biomass crosslinker,in a shape memory polycaprolactone network

This work reports a new direction of natural lignin valorization, which utilizes lignin to produce crosslinked polycaprolactone (PCL) via a straightforward synthesis. Lignin's hydroxyl groups of its multibranched phenolic structure allow lignin to serve as crosslinkers, whereas the aromatic groups serve as hard segments. The modified natural lignin containing alkene terminals is crosslinked with a thiol‐terminal PCL via Ru‐catalyzed photoredox thiol‐ene reaction. The high rate of gel contents measured for all crosslinked polymers, with the least being 84% of gel content, indicates efficient crosslinking. The prepared flat rectangular shape lignin‐crosslinked PCL sample demonstrates rapid thermal responsive shape memory behavior at 10 °C and 80 °C showing interconversion between a permanent and temporary shape. The melting temperature of the lignin‐crosslinked PCL is tunable by varying the percent weight of lignin. The 11, 21, and 30 wt % lignin demonstrated T_m of 42 °C, 35 °C, and 26 °C, respectively. The role of lignin as a crosslinker presented in this work suggests that lignin can serve as an efficient biomass‐based functional additive to polymers. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2121–2130     

New photo‐induced thiol‐ene crosslinked films based on linear methacrylate copolymer polythiols

Thiol‐ene radical addition by photolysis is a highly efficient click reaction of sufhydryl groups with reactive enes that has been extensively explored as a promising means to construct multifunctional materials. Here, photo‐induced thiol‐ene crosslinked films composed of linear methacrylate copolymer polythiols (MCPsh) are reported. Well‐defined MCPsh copolymers were prepared by thiol‐responsive cleavage of pendant disulfide linkages positioned in the corresponding methacrylate copolymers with narrow molecular weight distribution which were synthesized by a controlled radical polymerization method. With a commercially available multifunctional acrylate as a model ene, photo‐induced thiol‐ene radical polyaddition of these polythiols is competitive to free‐radical homopolymerization of acrylates, yielding crosslinked films exhibiting rapid cure, uniform network, and enhanced mechanical properties; these properties are required for high performance coating materials. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2860–2868.     

Facile synthesis and crosslinking reaction of trifunctional five‐membered cyclic carbonate and dithiocarbonate

The trifunctional five‐membered cyclic carbonate 2 and dithiocarbonate 3 were successfully synthesized by the reaction of trifunctional epoxide 1 with carbon dioxide and carbon disulfide, respectively. The crosslinking reactions of 2 with p‐xylylenediamine or hexamethylenediamine were carried out in dimethyl sulfoxide at 100 °C for 48 h to produce the corresponding crosslinked poly(hydroxyurethane)s quantitatively. The crosslinking reactions of 3 with both p‐xylylenediamine and hexamethylenediamine, followed by acetylation of thiol moiety, produced the corresponding crosslinked poly(thioester–thiourethane)s quantitatively. The obtained crosslinked poly(hydroxyurethane)s were thermally more stable than the analogous crosslinked poly(thioester–thiourethane)s, probably because of less thermal stability of thiourethane moiety than hydroxyurethane moiety. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5983–5989, 2004     

Poly(Alkyl Glycidate Carbonate)s as Degradable Pressure‐Sensitive Adhesives

Insertion of CO₂ into the polyacrylate backbone, forming poly(carbonate) analogues, provides an environmentally friendly and biocompatible alternative. The synthesis of five poly(carbonate) analogues of poly(methyl acrylate), poly(ethyl acrylate), and poly(butyl acrylate) is described. The polymers are prepared using the salen cobalt(III) complex catalyzed copolymerization of CO₂ and a derivatized oxirane. All the carbonate analogues possess higher glass‐transition temperatures (T_g=32 to ?5 °C) than alkyl acrylates (T_g=10 to ?50 °C), however, the carbonate analogues (T_d≈230 °C) undergo thermal decomposition at lower temperatures than their acrylate counterparts (T_d≈380 °C). The poly(alkyl carbonates) exhibit compositional‐dependent adhesivity. The poly(carbonate) analogues degrade into glycerol, alcohol, and CO₂ in a time‐ and pH‐dependent manner with the rate of degradation accelerated at higher pH conditions, in contrast to poly(acrylate)s.     

Polyaddition of bis(seven‐membered cyclic carbonate) with diamines: A novel and efficient synthetic method for polyhydroxyurethanes

This article deals with the polyaddition of a novel bis(seven‐membered cyclic carbonate), 1,2‐bis[3‐(1,3‐dioxepan‐2‐one‐5‐yl)‐propylthio]ethane, with the diamines 4,9‐dioxa‐1,12‐dodecanediamine and p‐xylylenediamine. The polyaddition was carried out at 30–70 °C for 6–24 h in dimethyl sulfoxide to obtain the corresponding polyhydroxyurethanes with number‐average molecular weights of 10,900–35,700 in good yields. The reaction of a monofunctional seven‐membered cyclic carbonate, 5‐allyl‐1,3‐dioxepan‐2‐one (7CC), with monoamines was also carried out to examine the reactivity in comparison with that of six‐ and five‐membered cyclic carbonates. The reaction rate constants of 7CC with n‐hexylamine and benzylamine were estimated to be 48.5 and 11.0 L/mol · h, respectively, in dimethyl sulfoxide‐d₆ (initial reagent concentration = 1 M) at 30 °C. The seven‐membered cyclic carbonate ring was 2.98 and 5.82 kcal/mol more strained than those of the six‐ and five‐membered cyclic carbonates, respectively, according to a semiempirical molecular orbital calculation with the PM3 Hamiltonian. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4091–4100, 2001     

Reactivity comparison of five‐ and six‐membered cyclic carbonates with amines: Basic evaluation for synthesis of poly(hydroxyurethane)

The reaction of six‐ and five‐membered cyclic carbonates, 5‐(2‐propenyl)‐1,3‐dioxan‐2‐one ( 1 ) and 4‐(3‐butenyl)‐1,3‐dioxolan‐2‐one ( 2 ) with hexylamine and benzylamine was carried out in N,N‐dimethylacetamide at 30, 50, and 70 °C. The six‐membered cyclic carbonate 1 proceeded quantitatively with hexylamine at 30 °C for 24 h, while the five‐membered cyclic carbonate 2 converted in 34%. The reaction rate constants at 50 °C are evaluated as follows; 1.42 L/mol · h ( 1 with hexylamine) > 0.29 L/mol · h ( 1 with benzylamine) > 0.04 L/mol · h ( 2 with hexylamine) > 0.01 L/mol · h ( 2 with benzylamine). The activation energies in the reactions of 1 and 2 with hexylamine were estimated to be 10.1 and 24.6 kJ/mol, respectively. The ring‐strain energy was calculated by the semi‐empirical method using the PM3 Hamiltonian. The ring‐strain energy of the six‐membered cyclic carbonate was 2.86 kcal/mol larger than that of five‐membered one. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 162–168, 2001     

Stereoregular polycarbonate synthesis: Alternating copolymerization of CO2 with aliphatic terminal epoxides catalyzed by multichiral cobalt(III) complexes

Completely stereoregular polycarbonate synthesis was achieved with the use of unsymmetric multichiral cobalt‐based complexes bearing a derived chiral BINOL and an appended 1,5,7‐triabicyclo[4.4.0] dec‐5‐ene as catalyst for the copolymerization of CO₂ and aliphatic terminal epoxides at mild conditions. The (S,S,S)‐Co(III) complex 1c with sterically hindered substituent group is more stereoregular catalyst for the copolymerization of CO₂ and racemic propylene oxide to afford a perfectly regioregular poly(propylene carbonate) (PPC), with >99% head‐to‐tail linkages, >99% carbonate linkages, and a K_rel of 24.4 for the enchainment of (R)‐epoxide over (S)‐epoxide. The isotactic PPC exhibits an enhanced glass transition temperature of 47 °C, which is 10–12 °C higher than that of the corresponding irregular polycarbonate. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.     

Photo‐induced thiol‐ene polysulfide‐crosslinked materials with tunable thermal and mechanical properties

Photo‐induced thiol‐ene crosslinked polymeric networks have been extensively explored in constructing a variety of new materials with enhanced mechanical properties for optical, biomedical, and sensing applications. Toward the broad applications, however, tunable mechanical properties are greatly desired. Here, an effective approach utilizing high‐molecular‐weight methacrylate copolymers having pendant thiol and vinyl groups (MCPsh and MCPenes) to modulate thermal and mechanical properties of photo‐induced thiol‐ene crosslinked materials is reported. The MCP copolymers are synthesized by an industrially friendly polymerization method, followed by post‐modification including either a facile coupling reaction or reductive cleavage. Upon UV irradiation, thiol‐ene reactive blends of MCPsh and MCPenes yield highly crosslinked materials through the formation of flexible sulfide linkages. These polysulfide‐crosslinked materials based on rigid MCP backbones exhibit enhanced mechanical properties. Further, their thermal and mechanical properties are tuned by modulating monomer compositions of MCPs as well as varying numbers of pendant SH or vinyl groups (i.e., extent of crosslinking densities). This approach is versatile and effective for development of high performance polymeric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3060–3068     

Crosslinkable poly(propylene carbonate): High‐yield synthesis and performance improvement

A crosslinking strategy was used to improve the thermal and mechanical performance of poly(propylene carbonate) (PPC): PPC bearing a small moiety of pendant C?C groups was synthesized by the terpolymerization of allyl glycidyl ether (AGE), propylene oxide (PO), and carbon dioxide (CO₂). Almost no yield loss was found in comparison with that of the PO and CO₂ copolymer when the concentration of AGE units in the terpolymer was less than 5 mol %. Once subjected to UV‐radiation crosslinking, the crosslinked PPC film showed an elastic modulus 1 order of magnitude higher than that of the uncrosslinked one. Moreover, crosslinked PPC showed hot‐set elongation at 65 °C of 17.2% and permanent deformation approaching 0, whereas they were 35.3 and 17.2% for uncrosslinked PPC, respectively. Therefore, the PPC application window was enlarged to a higher temperature zone by the crosslinking strategy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5329–5336, 2006     

Crosslinked poly(ethylene oxide) containing siloxanes fabricated through thiol‐ene photochemistry

Homogenous amphiphilic crosslinked polymer films comprising of poly(ethylene oxide) and polysiloxane were synthesized utilizing thiol‐ene “ click ” photochemistry. A systematic variation in polymer composition was Carried out to obtain high quality films with varied amount of siloxane and poly(ethylene oxide). These films showed improved gas separation performance with high gas permeabilities with good CO₂/N₂ selectivity. Furthermore, the resulting films were also tested for its biocompatibility, as a carrier media which allow human adult mesenchymal stem cells to retain their capacity for osteoblastic differentiation after transplantation. The obtained crosslinked films were characterized using differential scanning calorimetry, dynamic mechanical analysis, thermogravimetric analysis, FTIR, Raman‐IR , and small angle X‐ray scattering. The synthesis ease and commercial availability of the starting materials suggests that these new crosslinked polymer networks could find applications in wide range of applications. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1548–1557     

Orthogonal multifunctionalization of aliphatic polycarbonate via sequential Michael addition and radical‐thiol‐ene click reactions

Aliphatic polycarbonate (PC) copolymer is synthesized by ring opening copolymerization of acrylate‐ and allyl‐functional cyclic carbonate monomers. The post‐polymerization functionalization of the resulting copolymer is performed quantitatively using a variety of thiol compounds via sequential Michael addition and photo‐induced radical thiol‐ene click reactions within relatively short reaction time at ambient temperature. This metal‐free click chemistry methodology affords the synthesis of biocompatible PC copolymer with multifunctional groups. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1581–1587     

Cyclic carbonate synthesis from epoxides and CO2 over cyanocobalamin/n‐Bu4NI

The synthesis of cyclic carbonates from epoxides and carbon dioxide catalyzed by cyanocobalamin and n‐Bu₄NI system was achieved under 0.8 MPa CO₂ pressure at 140°C without organic solvents. Propylene carbonate was obtained in 99% yield within 6 h under the optimized reaction conditions. The cyanocobalamin catalyst could be recycled with water and retained moderate catalytic activity. Copyright © 2012 John Wiley & Sons, Ltd.