脂肪族水性聚氨酯的动态力学行为研究

合成了一系列脂肪族水性聚氨酯 .考察了软段的组成、软段分子量及DMPA用量对产物动态力学性能的影响作用 .实验结果表明 ,软段的化学结构对水性聚氨酯的相态结构影响很大 .聚醚型水性聚氨酯具有较低的软段玻璃化转变温度 (Tgs) .聚醚型产物的微相分离程度高于聚酯型产物 .当采用聚酯和聚醚二元醇为混合软段时 ,Tgs随软段中聚醚含量的提高而逐渐降低 .提高DMPA用量 ,软段玻璃化转变温度Tgs移向低温区 ,硬段玻璃化转变温度Tgh移向高温区 ,说明体系的微相分离程度加大 .当软段分子量较低时 ,产物为半相容结构 ,只有一个主转变峰 ,软段的玻璃化转变以肩峰的形式出现 ;当软段分子量较高时 ,产物的微相分离程度较高 ,可以分别观察到软段及硬段的玻璃化转变 .总之 ,通过改变软段的种类、组成和分子量以及DMPA用量 ,可以大幅度地改变水性聚氨酯的形态结构 .     

液化MDI/PHMA体系形状记忆聚氨酯结构与性能的研究

用聚已二酸已二酯(PHMA)为软段,液化MDI和BDO为硬段,采用两步溶液法合成了具有形状记忆功能的多嵌段聚氨酯,利用DSC,WAXD等测试手段分析了该体系的形态结构,同时讨论了该体系的形状记忆行为、拉伸力学性能及动态力学性能.结果发现,该体系SMPU的硬段以无定形存在,软段具有很好的结晶性能;具有很好的形状记忆性能,形状固定率可达100%,形状回复率在97%以上,回复温度在35~45℃;同时它兼有较高的拉伸强度(约为28~50 MPa)和断裂伸长率(约为900%~1400%);动态力学性能卓越,其室温模量可达279.8 MPa,软段熔融前后模量比可达140.     

二苯醚—对苯二甲酰氯—4,4‘—二苯氧基二苯砜三元共聚物的合成与性能

以无水ＡｌＣｌ３／ＣｌＣＨ２ＣＨ２Ｃｌ／ＮＭＰ为催化剂／溶剂体系，通过缩聚反应，由二苯醚，对苯二甲酰氯和４，４－二苯氧基二苯砜合成了聚醚酮酮和聚醚砜醚酮酮共聚物（ＰＥＫＫ／ＰＥＳＥＫＫ）．考察了单体浓度、反应时间对聚合物分子量的影响，并对其进行了ＩＲ、ＤＳＣ、ＷＡＸＤ等分析表征．结果表明，共聚物具有优异的耐热性，随着共聚物中ＰＥＳＥＫＫ单元含量的增加，其玻璃化温度逐渐升高，而熔融温度和结晶度逐渐降低．与聚醚酮酮（ＰＥＫＫ）相比，共聚物的断裂伸长率明显提高，而拉伸强度和拉伸模量却有所下降，但仍具有良好的力学性能．     

短纤维/硅树脂复合材料的性能研究

分别用ＰＥＴ短纤维和硅灰石（无机针状晶须）增强甲基乙烯基硅树脂,研究了纤维长度、含量与复合材料力学性能的关系,并考察了增强纤维对硅树脂热稳定性的影响。结果表明：ＰＥＴ短纤维增强硅树脂复合材料的拉伸强度、模量和硬度显著提高,断裂伸长率下降;ＰＥＴ纤维长径比在１８０～３００范围内时,复合材料的拉伸强度增大;硅灰石增强的复合材料强度、模量及硬度提高相对较小,断裂伸长率随强体用量增多,先增加而后降低,存在     

用可再生原料合成聚氨酯脲水分散液——成膜后的结构与性能研究

以不同组成的蓖麻油和二官能度聚醚多元醇 (GE 2 10 )等原料合成了聚氨酯脲 (PUU)水分散液 ,研究了蓖麻油 GE 2 10的组成对PUU膜结构与性能的影响 .结果表明 ,由GE 2 10合成的PUU虽软硬段间存在一定的相容性 ,但其中脲羰基的氢键化程度高 ,硬段形成较好的有序结构 ,导致PUU膜具有较高的拉伸强度及断裂伸长率 ,但弹性模量和硬度下降 .在蓖麻油合成的PUU中脲羰基的氢键化程度及硬段有序结构均受到化学交联结构的抑制 ,故PUU膜的拉伸强度和断裂伸长率降低 ,但弹性模量及硬度较高 .由蓖麻油与GE 2 10在一定的组成范围内合成的PUU膜 ,具有优良的综合平衡的力学性能 ,后者与材料的结构形态相符     

高分子量聚乙烯醇增强冰的研究

以本体光聚合法制备的高分子量聚乙烯醇(HMWPVA)为增强剂,考察了增强冰的力学性能.当HMWPVA的浓度为3%(质量分数)时,增强冰的拉伸强度、断裂伸长率、压缩强度和压缩模量分别为普通冰的11.7,3.5,2.3和2.1倍.对比试验发现PVA分子量对冰的拉伸性能影响较大,对冰的压缩性能影响较小.此外,在室温29℃时纯冰的融化时间为5 min,而4%HMWPVA增强冰的融化时间长达240 min.     

软段对水性聚氨酯结构与性能的影响

以低聚物多元醇、异氟尔酮二异氰酸酯(IPDI)、亲水单体二羟甲基丙酸(DMPA),乙二胺为主要原料,制备了一组不同组成的聚氨酯乳液。通过粘度测定、粒度分析、力学性能和耐水性能测试、原子力显微镜(AFM)分析,研究了软段类型、软段分子量对乳液及其胶膜性能的影响。结果表明,分子结构规整、易结晶的软段合成的聚氨酯树脂力学性能和耐水性能都较好,对聚己二酸酯而言,分子量减小,其合成的水性聚氨酯拉伸强度提高,耐水性能却有很大程度的下降。     

谷朊粉/淀粉/甘油混合体系的流变行为与力学性能

研究了甘油增塑谷朊粉/淀粉混合体系的动态流变行为与单轴拉伸力学性能,考察了淀粉与水含量的影响.研究结果表明,含水量10%的混合体系储能模量(G′)随淀粉含量增大而增大,并在100℃出现橡胶平台.增塑谷朊粉在30℃呈现凝胶特性,在80℃出现交联网络结构.淀粉粒子可与小麦蛋白质形成复杂相互作用,阻碍蛋白质链段运动,导致模量与强度增加,断裂伸长率降低.含水量为20%与25%时,水份在淀粉粒子与蛋白质网络间起稀释和润滑作用,拉伸强度与断裂伸长率随淀粉含量的增高而降低.     

聚β-羟基丁酸酯/聚氧化乙烯共混体系力学性能研究

本文详细研究了可完全生物降解的聚 β 羟基丁酸酯 (PHB)与水溶性聚氧化乙烯 (PEO)两元共混体系的拉伸力学性能 .讨论了PEO分子量、共混组成及热处理条件对共混体系力学性能的影响 .其中 ,PHB与超高分子量PEO(重均分子量 5× 10 6)共混 ,两组分力学上具有相容性 ,共混物的拉伸强度、断裂伸长率及模量都有明显的正的协同效应 .共混改性效果显著PHB的力学性能得到很大改善 ,尤其PHB的脆性缺陷 .并且 ,共混物在经过适当温度退火处理之后 ,共混物性能还可进一步改善     

MC尼龙-纳米La2O3复合材料的制备及性能研究

用原位分散聚合法制备了一系列MC尼龙／纳米La2O3复合材料，研究了纳米La2O3用量对复合材料力学性能的影响，用SEM观察了La2O3粒子在MC尼龙基体中的分散情况，用XRD对复合材料的晶体结构进行了表征。SEM观察结果表明，当纳米La2O3用量小于1％时，纳米La2O3均匀分散于MC尼龙基体中，团聚情况很少，当纳米La2O3用量大于1％时，纳米La2O3开始团聚；XRD研究结果表明，纳米La2O3没有改变MC尼龙的结晶形态；力学性能的研究结果表明，随着纳米La2O3用量的增加，复合材料的拉伸强度、断裂伸长率、缺口冲击强度、弯曲强度和弯曲模量都呈先升后降的趋势，当纳米La2O3用量为0．5％时，复合材料的拉伸强度和断裂伸长率达到最大值，分别比MC尼龙提高17．9％和52．1％，当纳米La2O3的用量为1．0％时，复合材料的缺口冲击强度、弯曲强度和弯曲模量达到最大值，分别比MC尼龙基体提高36，6％．12．7％和16．3％。     

Influence of plasticizers and crosslinking on the properties of biodegradable films made from sodium caseinate

Plasticized protein films were prepared by the casting method from water solution of sodium caseinate and plasticizers with the aim to obtain environmentally friendly materials for packaging applications. Mechanical properties (tensile strength, elongation and Young’s modulus) of caseinate based films were determined versus ratio of protein to plasticizer, plasticizer type and relative humidity conditions. Among the different polyol-type plasticizers tested, glycerol (Gly) and triethanolamine (TEA) were the most efficient for the improvement of mechanical properties (high strains for low stresses). Further, chemical crosslinking between formaldehyde (HCHO) and free amino groups (ε-NH₂) of sodium caseinate was performed to increase water resistance of TEA plasticized films. Optimal mechanical properties, i.e. elastic modulus of 105 MPa, tensile strength of 8-9 MPa for elongation at break about 110-125% were obtained for HCHO/ε-NH₂ ratios higher than 1.35. Protein specific water solubility was determined from a 280 nm absorbance. For convenient crosslinker (HCHO) content sodium caseinate solubility can be lowered to less than 5 wt% after 24 h immersion in water.     

Polyurethane cationomers. I. Structure-property relationships

Polyether polyurethane cationomers are prepared using poly (tetramethylene oxide) of molecular weight 2000 as soft segments, N-methyl-diethanolamine as chain extender, glycolic acid as quaternization agent, methyl ethyl ketone as solvent, and three different diisocyanates. The three diisocyanates are 4,4′-diphenylenemethylene diisocyanate (MDI), hexamethylene diisocyanate (HDI), and toluene diisocyanate (TDI). Properties of the films cast from solutions of the three series of ionomers are studied by infrared spectroscopy, dynamic mechanical analysis, thermogravimetric analysis, differential scanning calorimetry, wide angle x-ray diffraction, and tensile elongation testing. In the un-ionized and ionized systems, the hard segments exhibit disordered and ordered arrangements, respectively. Ionization disrupts the order and produces increased cohesion in the hard domains, which have opposing effects on the tensile elongation properties. In the MDI and TDI systems, cohesion is predominant, leading to an increased tensile strength and modulus and decreased elongation at break. But in the HDI system, the disruption of the order is predominant, leading to decreased tensile strength and only insignificant reduction in the elongation at break. In the TDI system, the tensile strength is rather low, which is attributed to the poor order in the hard domains resulting from the high content of the asymmetric 2,4-isomer of the urethane.     

鞋用水性聚氨酯胶黏剂的制备及表征

通过预聚体分散法,以二羟甲基丙酸(DMPA)、蔗糖(sucrose)为亲水扩链剂和交联剂制备了一种鞋用水性聚氨酯胶黏剂.通过FTIR、DSC、力学性能、固化速度等研究了蔗糖用量对聚氨酯结构与性能的影响.结果表明蔗糖己引入聚氨酯主链.随着蔗糖用量的增加,相同处理温度下聚氨酯胶液的固化速度提高,胶膜的吸水率降低,拉伸强度增大,断裂伸长率减小,粘接试样的T-剥离强度逐渐增大.当蔗糖用量超过5.52 wt%时,合成及乳化过程中体系容易凝聚,且所制得的胶黏剂粘接强度有所下降.总之,通过改变蔗糖用量可以显著改变水性聚氨酯结构与性能.     

Comparison of the properties of waterborne polyurethane/multiwalled carbon nanotube and acid‐treated multiwalled carbon nanotube composites prepared by in situ polymerization

A series of waterborne polyurethane (WBPU)/multiwalled carbon nanotube (CNT) and WBPU/nitric acid treated multiwalled carbon nanotube (A‐CNT) composites were prepared by in situ polymerization in an aqueous medium. The optimum nitric acid treatment time was about 0.5 h. The effects of the CNT and A‐CNT contents on the dynamic mechanical thermal properties, mechanical properties, hardness, electrical conductivity, and antistatic properties of the two kinds of composites were compared. The tensile strength and modulus, the glass‐transition temperatures of the soft and hard segments (T_gs and T_gh, respectively), and ΔT_g (T_gh − T_gs) of WBPU for both composites increased with increasing CNT and A‐CNT contents. However, these properties of the WBPU/A‐CNT composites were higher than those of the WBPU/CNT composites with the same CNT content. The electrical conductivities of the WBPU/CNT1.5 and WBPU/A‐CNT1.5 composites containing 1.5 wt % CNTs (8.0 × 10⁻⁴ and 1.1 × 10⁻³ S/cm) were nearly 8 and 9 orders of magnitude higher than that of WBPU (2.5 × 10⁻¹² S/cm), respectively. The half‐life of the electrostatic charge (τ_1/2) values of the WBPU/CNT0.1 and WBPU/A‐CNT0.1 composites containing 0.1 wt % CNTs were below 10 s, and the composites had good antistatic properties. From these results, A‐CNT was found to be a better reinforcer than CNT. These results suggest that WBPU/A‐CNT composites prepared by in situ polymerization have high potential as new materials for waterborne coatings with good physical, antistatic, and conductive properties. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3973–3985, 2005     

Study of viscoelastic properties of white carbon black reinforced synthetic polyisoprene

The viscoelastic properties of synthetic polyisoprenes(PI) reinforced by white carbon black(WCB) have been investigated and compared with WCB reinforced natural rubber(NR), including cure characteristics, physio-mechanical and dynamic mechanical properties. Compared with NR, PI loaded with the same amount of WCB(PI/WCB) exhibited shorter scorch time and optimal cure time, indicating that WCB fillers are comparatively easier to conjugate with PI. The tensile strength and elongation at break decreased with WCB filling in both PI and NR vulcanizates. The hardness of the rubber vulcanizates increased with the WCB filling in the rubber matrix. PI/WCB blends exhibited smaller hardness data, lower tensile strength, as well as lower elongation at break and tensile stress. Increasing the amount of WCB in rubber matrix induced the Payne effect. However, the Payne effect is much more obvious for the PI/WCB system, and PI/WCB also displayed higher storage modulus whereas lower loss modulus and loss tangent than NR/WCB, which could all be attributed to the poor dispersibilities of WCB in the PI matrix.     

Optimisation of physical and mechanical properties of rubber compounds by response surface methodology--Two component modelling using vegetable oil and carbon black

Response surface methodology was used for predicting the optimal composition of vegetable oil and carbon black in rubber compounding. Central composite rotatable design for two variables at five levels was chosen as the experimental design. The data obtained from measurement of properties was fitted as a two variable second order equation and were plotted as contour plots using programme developed in MATLAB v.5. It is observed from the contour plots that the increase in cross-link density caused by the formation of rubber mono-layer from its multi-layer on increasing the carbon black loading upto the central point (50 phr) of experimental region increases 300% modulus and elongation at break and reduces the ultimate properties like tear strength and tensile strength. On the other-hand hardness increases with increase in solid inclusion of carbon black. From the contours it is observed that the addition of vegetable oil upto 2-3 phr, cross-link density increases due to its coupling action leading to increase in hardness and modulus and lowering of ultimate properties like tensile strength and elongation at break. Addition of further amount of vegetable oil shows less coupling and more plasticising effect leading to increase in tear strength, tensile strength and elongation at break and decrease in hardness and 300% modulus.     

Effects of monomer structure and imidization degree on mechanical properties and viscoelastic behavior of thermoplastic polyimide films

Two thermoplastic polyimides based on a common diamine (3,4′-ODA) were synthesized using different dianhydrides, namely ODPA and BPDA by a two step method. Molecular weight was controlled by using PA as an end capping agent. Effects of imidization degree on the mechanical properties and viscoelastic behavior of thermoplastic polyimide films were investigated. Film samples with varying degrees of imidization were characterized using FTIR, DMTA and tensile properties testing. It was found that two polyimides have different rates of imidization because of difference in monomer reactivity and molecular structure. It was observed that with an increase in imidization degree there was a decrease in thermoplastic response and a change in viscoelastic behavior from liquid-like to solid-like. With increase in imidization degree the tensile modulus and tensile strength of the films were increased, whereas elongation at break and tensile breaking energy were found to decrease after a certain imidization temperature.     

Preparation and characterization of waterborne polyurethane/attapulgite nanocomposites

In this paper, waterbrone polyurethane (WPU)/attapulgite (AT) nanocomposites have been prepared by direct emulsion blending. The WPU was synthesized from poly(tetramethylene glycol), 4,4-diphenylmethane diisocyanate, dimethylol butanic acid, and neutralized by triethylamine. SEM examination of fractured surfaces showed that AT particles were irregularly dispersed in the WPU matrix. FTIR analysis suggested no major chemical structural changed in the presence of a small amount of AT. DMA results showed that the storage modulus of WPU/AT nanocomposites was increased and the glass transition temperatures of both soft and hard segments shifted to higher temperature compared to the pristine WPU. Thermal resistance of the samples measured by TGA was improved with the addition of AT. The mechanical properties of the nanocomposites, examined by tensile tests, showed higher tensile strength and elongation at break than that of the pristine WPU.