Hole‐buffer polymer composed of alternating p‐terphenyl and tetraethylene glycol ether moieties: Synthesis and application in polymer light‐emitting diodes

Carrier balance is essential to obtain efficient emission in polymer light‐emitting diodes (PLEDs). A new polymer 3P5O composed of alternating p‐terphenyl and tetraethylene glycol ether segments is designed and synthesized by the Suzuki coupling reaction and successfully employed as hole‐buffer layer to improve carrier balance. Multilayer PLEDs [ITO/PEDOT:PSS/ 3P5O /SY/LiF/Al], with Super Yellow (SY) as the emitting layer and 3P5O as the hole‐buffer layer, reveal maximum luminance (17,050 cd/m²) and maximum current efficiency (6.6 cd/A) superior to that without the hole‐buffer layer (10,017 cd/m², 3.0 cd/A). Moreover, it also shows better performance than that using conventional BCP as hole‐blocking layer [ITO/PEDOT:PSS/SY/BCP/LiF/Al (80 nm): 13,639 cd/m², 4.1 cd/A]. The performance enhancement has been attributed to hole‐buffering characteristics of 3P5O that results in improved carrier recombination ratio and wider carrier recombination region. Current results indicate that the 3P5O is a promising hole‐buffer polymer to enhance the performance of optoelectronic devices. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 785–794     

Cascade hole transport in efficient green phosphorescent light‐emitting devices achieved by layer‐by‐layer solution deposition using photocrosslinkable‐conjugated polymers containing oxetane side‐chain moieties

A hole‐injection/transport bilayer structure on an indium tin oxide (ITO) layer was fabricated using two photocrosslinkable polymers with different molecular energy levels. Two photoreactive polymers were synthesized using 2,7‐(or 3,6‐)‐dibromo‐9‐(6‐((3‐methyloxetan‐3‐yl)methoxy)hexyl)‐9H‐carbazole) and 2,4‐dimethyl‐N,N‐bis(4‐ (4,4,5,5‐tetramethyl‐1,3,2‐dioxaborolan‐2‐yl)phenyl)aniline via a Suzuki coupling reaction. When the oxetane groups were photopolymerized in the presence of a cationic photoinitiator, the photocured film showed good solvent resistance and compatibility with a poly(N‐vinylcarbazole) (PVK)‐based emitting layer. Without the use of a conventional hole injection layer (HIL) of poly(3,4‐ethylenedioxythiophene)/(polystyrenesulfonate) (PEDOT:PSS), the resulting green light‐emitting device bearing PVK: 5‐4‐tert‐butylphenyl‐1,3,4‐oxadiazole (PBD):Ir(Cz‐ppy)3 exhibited a maximum external quantum efficiency of 9.69%; this corresponds to a luminous efficiency of 29.57 cd/A for the device K‐4 configuration ITO/POx‐I/POx‐II/PVK:PBD:Ir(Cz‐ppy)3/triazole/Alq3/LiF/Al. These values are much higher than those of PLEDs using conventional PEDOT:PSS as a single HIL. The significant improvement in device efficiency is the result of suppression of the hole injection/transport properties through double‐layered photocrosslinked‐conjugated polymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Electroluminescent properties of a partially‐conjugated hyperbranched poly(p‐phenylene vinylene)

In this paper, the electroluminescent properties of a new partially‐conjugated hyperbranched poly (p‐phenylene vinylene) (HPPV) were studied. The single layer light‐emitting device with HPPV as the emitting layer emits blue‐green light at 496 nm, with a luminance of 160 cd/m² at 9 V, a turn‐on voltage of 4.3 V and an electroluminescent efficiency of 0.028 cd/A. By doping an electron‐transport material [2‐(4‐biphenylyl)‐5‐phenyl‐1,3,4‐oxadiazole, PBD] into the emitting layer and inserting a thin layer of tris(8‐hydroxy‐quinoline)aluminum (Alq₃) as electron transporting/hole blocking layer for the devices, the electroluminescent efficiency of 1.42 cd/A and luminance of 1700 cd/m² were achieved. The results demonstrate that the devices with the hyperbranched polymers as emitting material can achieve high efficiency through optimization of device structures. Copyright © 2006 John Wiley & Sons, Ltd.     

A novel bright blue electroluminescent polymer: poly[4,4′‐biphenylene‐α‐(9″,9″‐dihexyl‐3‐fluorenyl) vinylene]

Poly[4,4′‐biphenylene‐α‐(9”,9”‐dihexyl‐2‐fluorenyl)vinylene] (PBPHFV) was synthesized by nickel catalyzed coupling reaction of 1,2‐bis(bromophenyl)‐1‐(9”,9”‐dihexyl‐2‐fluorenyl)ethene and characterized by spectroscopic methods and elemental analysis. PBPHFV is soluble in common organic solvents. The weight average molecular weight (Mw) of PBPHFV is about 15000. PBPHFV showed good thermal stability as weight loss was less than 5 % on heating to 420 C under nitrogen atmosphere. The polymer film showed maximum absorption and emission at 370 nm and 485 nm, respectively. A bright blue electroluminescence (λ_max = 465nm, maximum intensity = 4116 cd/m²) was obtained when the device was fabricated with the structure of ITO/PEDOT/PBPHFV/LiF/Al. The turn on voltage of the device was 4.3 V and the maximum efficiency was 0.22 lm/W. When the blend with PVK (PBPHFV : PVK = 1:5) was used as an emitting layer, the maximum brightness and efficiency of the device were 9342 cd/m² and 1.66 lm/W, respectively.     

A novel oligothiophene derivative as a hole‐transport with emitting material for OLED

A novel oligothiophene derivative containing the triphenylamine moiety with high glass transition temperature (T_g; 135 °C), 5,5′‐{bis[4‐di(4‐thiophenyl)amino]phenyl}‐2,2′‐bithiophene (TTPA‐dimer) was synthesized by the dimerization of tris[4‐(2‐thienyl)phenyl]amine (TTPA) with a palladium catalysis. Some types of electroluminescent (EL) devices that use the amorphous material for a hole‐ and an electron‐transporting with an emitting layer were fabricated. These devices emitted a bright green‐yellowish light (λ_emi; around 510 nm) with a small full width at half maximum (FWHM) rather than that of Alq₃. The single layer EL device showed a maximum luminance of 221 cd/m² at 8 V (0.06 lm/W at 100 cd/m²). On the other hand, the double layer (TTPA‐dimer/Alq₃) EL device that used Alq₃ as the electron transport material was increased up to 10830 cd/m² at 12 V (0.89 lm/W at 300 cd/m²) and with a lower turn‐on voltage (3.2 V at 0.1 cd/m²) than other types of EL devices. Copyright © 2003 John Wiley & Sons, Ltd.     

Thermally crosslinkable hole‐transporting poly(fluorene‐co‐triphenylamine) for multilayer polymer light‐emitting diodes

This article reports the synthesis and characterization of a novel thermally crosslinkable hole‐transporting poly (fluorene‐co‐triphenylamine) (PFO‐TPA) by Suzuki coupling reaction, followed with its application in the fabrication of multilayer light‐emitting diodes by wet processes. The thermal, photophysical, and electrochemical properties of PFO‐TPA were investigated by differential scanning calorimeter, thermogravimetric analysis, optical spectroscopy, and cyclic voltammetry, respectively. Thermally crosslinked PFO‐TPA, through pendant styryl groups, demonstrates excellent thermal stability (T_d > 400 °C, T_g = 152 °C), solvent resistance, and film homogeneity. Its highest occupied molecular orbital level (?5.30 eV) lies between those of PEDOT:PSS (?5.0 ～ ?5.2 eV) and poly(9,9‐dioctylfluorene) (PFO: ?5.70 eV), forming a stepwise energy ladder to facilitate hole injection. Multilayer device with crosslinked PFO‐TPA as hole‐injection layer (HIL) (ITO/PEDOT:PSS/HIL/PFO/LiF/Ca/Al) was readily fabricated by successive spin‐coating processes, its maximum luminance efficiency (3.16 cd/A) were about six times higher than those without PFO‐TPA layer (0.50 cd/A). The result of hole‐only device also confirmed hole‐injection and hole‐transport abilities of crosslinked PFO‐TPA layer. Consequently, the device performance enhancement is attributed to more balanced charges injection in the presence of crosslinked PFO‐TPA layer. The thermally crosslinkable PFO‐TPA is a promising material for the fabrication of efficient multilayer polymer light‐emitting diodes because it is not only a hole‐transporting polymer but also thermally crosslinkable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

The Effect of Controlled Dopant Concentration on the Performance of Blue Polymer Light‐emitting Diodes

The performance of a blue polymer light‐emitting diodes (PLED) was significantly improved by doping a controlled amount (<1%) of a hole transport molecule N,N′‐bis‐(1‐naphthyl)‐N,N′‐diphenyl‐1,1′‐biphenyl‐4,4″‐diamine (NPB) into the emitting layer. Hole carrier mobility of the blue emitting polymer, BP105 (trade name of The Dow Chemicals Co.), increased from 5.27 × 10^‐7 cm^‐2/Vs of the pristine BP105 to 1.80 × 10^‐6 cm^‐2/Vs with the addition of 1% NPB in BP105. The enhanced carrier mobility greatly promoted performance of a blue PLED device with a device structure of ITO/PEDOT:PSS/BP105+x% NPB/LiF/Ca/Al. Luminance increased from 573 cd/m² to 2,720 cd/m² at 6V and efficiency increased from 1.1 lm/W to 1.6 lm/W at 1,000 cd/m² with 1% NPB in BP105. The most important improvement was an increase in the lifetime of the blue device from 80 to 120 hours at an initial luminance of 400 cd/m². We found that by choosing the appropriate dopant with good energy alignment and controlled dopant concentration, the performance of a blue PLED device could be greatly improved.     

Synthesis of novel nitrogen‐ and sulfur‐containing conjugated polymers used as hole‐transporting materials for organic light‐emitting diodes

Two series of highly soluble novel nitrogen‐ and sulfur‐containing conjugated polymers were synthesized via an acid‐induced self‐polycondensation of functional monomers with methyl sulfinyl and aromatic groups. The well‐defined structures of synthesized polymers were confirmed by their NMR and IR spectra. The highest occupied molecular orbital energy values for these materials, estimated by cyclic voltammetry, showed a broad range of values from about 5.0 to 5.2 eV used as hole‐transport layers (HTL) in two‐layer light‐emitting diodes ITO/HTL/Alq₃/Mg:Ag [ITO = indium tin oxide, and Alq₃ = tris(8‐quinolinato) aluminum]. The typical turn‐on voltage of these diodes was about 4–5 V. The maximum brightness of the device was about 3440 cd/m² at 20 V. The maximum efficiency was estimated to be 0.15 lm/W at 10 V. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1321–1333, 2002     

Anthracene‐Cored Dendrimer for Solution‐Processible Blue Emitter: Syntheses,Characterizations, Photoluminescence,and Electroluminescence

Summary: A second‐generation blue fluorescent anthracene‐cored dendrimer EH‐G2AN was readily synthesized via a convergent method. Its monodispersity was confirmed by ¹H NMR and MALDI‐TOF mass measurement. The peak emission of EH‐G2AN in a dilute CH₂Cl₂ solution was observed at 416 nm with a shoulder at 434 nm and moved to 418 nm in the solid film with the shoulder at 433 nm. The nearly “perfect” overlap of solution and solid emission spectra revealed the absence of molecular aggregations in the solid film, which was apparently suppressed by the presence of rigid and bulky 1,3,5‐phenylene‐based dendrons and 2‐ethylhexyloxy solubilizing peripheral groups. EH‐G2AN appeared strikingly stable with the onset decomposition temperature above 350 °C and remained at the high temperature of 428 °C where 5% weight loss occurred. The electroluminescent device [ITO/PEDOT:PSS/EH‐G2AN/Ba/Al] showed a peak emission at 442 nm and maximal external device efficiency of 0.82%@170 cd · m⁻². After inserting a PVK layer between the hole injection layer and emitting layer, a maximal external device efficiency of 1.05%@184 cd · m⁻² was obtained with a narrow FWHI of merely ca. 42 nm in the device configuration [ITO/PEDOT:PSS/PVK/EH‐G2AN/Ba/Al].

     

Synthesis and characterization of light‐emitting oligo(p‐phenylene‐vinylene)s and polymeric derivatives containing three‐ and five‐conjugated phenylene rings. II. Electro‐optical properties and optimization of PLED performance

A series of multilayer polymeric light‐emitting diodes (PLEDs) containing an electron‐transporting layer (ETL), that is tris(8‐quinolinolato)‐aluminum(III) (Alq) and 2,2′,2″‐(1,3,5‐phenylene)‐tris[1‐phenyl‐1H‐benzimidazole] (TPBI), were fabricated by doping fluorescent oligo(p‐phenylene‐vinylene)s (BIII and BV) and polymer derivatives (PBV) into poly(N‐vinyl carbazole) (PVK). These PLEDs can be optimized by the design of multilayer device configurations (brightness increased 8–15 times by addition of ETL) and possess greenish electroluminescent (EL) spectra peaked about 500–540 nm. A remarkably high brightness of 56,935 cd/m² with a power efficiency of 3.25 lm/W was obtained in the device of PVK:BVOC₈‐OC₈ (100:20)/Alq (60 nm/60 nm). It suggests that the emission mechanism (including the conjugated and excimer emissions of BVOC₈‐OC₈ emitters) originates from both of BVOC₈‐OC₈ and ETL (Alq and TPBI) by varying the concentration of chromophores and adjusting the thickness of ETL. The concentration effect of the emitters in PVK (i.e. PVK:BVOC₈‐OC₈ = 100:5, 100:20, and 100:100 wt %) and the influence of the ETL (including its thickness) on the EL characteristics are also reported. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2922–2936, 2006     

Solution‐processable and thermally cross‐linkable fluorene‐cored triple‐triphenylamines with terminal vinyl groups to enhance electroluminescence of MEH‐PPV: Synthesis,curing, and optoelectronic properties

This study reports the synthesis, curing, and optoelectronic properties of a solution‐processable, thermally cross‐linkable electron‐ and hole‐blocking material containing fluorene‐core and three periphery N‐phenyl‐N‐(4‐vinylphenyl)benzeneamine ( FTV ). The FTV exhibited good thermal stability with T_d above 478 °C in nitrogen atmosphere. The FTV is readily cross‐linked via terminal vinyl groups by heating at 160 °C for 30 min to obtain homogeneous film with excellent solvent resistance. Multilayer PLED device [ITO/PEDOT:PSS/cured‐ FTV /MEH‐PPV/Ca (50 nm)/Al (100 nm)] was successfully fabricated using solution processed. Inserting cured‐ FTV is between PEDOT:PSS and MEH‐PPV results in simultaneous reduction in hole injection from PEDOT:PSS to MEH‐PPV and blocking in electron transport from MEH‐PPV to anode. The maximum luminance and maximum current efficiency were enhanced from 1810 and 0.27 to 4640 cd/m² and 1.08 cd/A, respectively, after inserting cured‐ FTV layer. Current results demonstrate that the thermally cross‐linkable FTV enhances not only device efficiency but also film homogeneity after thermal curing. FTV is a promising electron‐ and hole‐blocking material applicable for the fabrication of multilayer PLEDs based on PPV derivatives. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 000: 000–000, 2012     

Copoly(p‐phenylene)s containing bipolar triphenylamine and 1,2,4‐triazole groups: Synthesis,optoelectronic properties,and applications

Two novel copoly(p‐phenylene)s ( P1 – P2 ) containing bipolar groups (12.8 and 6.8 mol %, respectively), directly linked hole transporting triphenylamine and electron transporting aromatic 1,2,4‐triazole, were synthesized to enhance electroluminescence (EL) of poly(p‐phenylene vinylene) (PPV) derivatives. The bipolar groups not only enhance thermal stability but also promote electron affinity and hole affinity of the resulting copoly(p‐phenylene)s. Blending the bipolar copoly‐(p‐phenylene)s ( P1 – P2 ) with PPV derivatives ( d6‐PPV ) as an emitting layer effectively improve the emission efficiency of its electroluminescent devices [indium tin oxide (ITO)/poly(3,4‐ethylenedioxythiophene) (PEDOT):poly(styrenesulfonate) (PSS)/polymer blend/Ca (50 nm)/Al (100 nm)]. The maximum luminance and maximum luminance efficiency were significantly enhanced from 310 cd m^?2 and 0.03 cd A^?1 ( d6‐PPV ‐based device) to 1450 cd m^?2 and 0.20 cd A^?1 (blend device with d6‐PPV / P1 = 96/4 containing ～0.5 wt % of bipolar groups), respectively. Our results demonstrate the efficacy of the copoly(p‐phenylene)s with bipolar groups in enhancing EL of PPV derivatives. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Deep‐red light‐emitting phosphorescent dendrimer encapsulated tris‐[2‐benzo[b]thiophen‐2‐yl‐pyridyl] iridium (III) core for light‐emitting device applications

New deep‐red light‐emitting phosphorescent dendrimers with hole‐transporting carbazole dendrons were synthesized by reacting tris(2‐benzo[b]thiophen‐2‐yl‐pyridyl) iridium (III) complex with carbazolyl dendrons by DCC‐catalyzed esterification. The resulting first‐, second‐, and third‐generation dendrimers were found to be highly efficient as solution‐processable emitting materials and for use in host‐free electrophosphorescent light‐emitting diodes. We fabricated a host‐free dendrimer EL device with configuration ITO/PEDOT:PSS (40 nm)/dendrimer (55 nm)/BCP (10 nm)/Alq₃ (40 nm)/LiF (1 nm)/Al (100 nm) and characterized the device performance. The multilayered devices showed luminance of 561 cd/m² at 383.4 mA/cm² (12 V) for 15 , 1302 cd/m² at 321.3 mA/cm² (14 V) for 16 , and 422 cd/m² at 94.4 mA/cm² (18 V) for 17 . The third‐generation dendrimer, 17 (η_ext = 6.12% at 7.5 V), showed the highest external quantum efficiency (EQE) with an increase in the density of the light‐harvesting carbazole dendron. Three dendrimers exhibited considerably pure deep‐red emission with CIE 1931 (Commission International de L'Eclairage) chromaticity coordinates of x = 0.70, y = 0.30. The CIE coordinates remained very stable with the current density. The integration of rigid hole‐transporting dendrons and phosphorescent complexes provides a new route to design highly efficient solution‐processable materials for dendrimer light‐emitting diode (DLED) applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 7517–7533, 2008     

Synthesis and characterization of polyfluorenes containing bisphenazine units

Novel conjugated copolymers based on 9,9‐dioctylfluorene and bisphenazine (BP) were synthesized by Suzuki polymerization. Energy transfer from the conjugated main chain to the BP moieties was observed. Full energy transfer was achieved when the molar content of the bisphenazine was 20% (20BPPF) in toluene solution. The similar phenomena were observed even for 1% bisphenazine content copolymer (1BPPF) in film. The lowest occupied molecular orbital (LUMO) energy levels (?3.06 eV) of the copolymers were lower than that of the polyfluorene homopolymer (PFO; ?2.65 eV), indicating that the introduction of the BP unit was benefit to electron injection. Single‐layer electroluminescent devices (ITO/PEDOT:PSS/polymer/LiF/Al) were fabricated to investigate their electroluminescence (EL) performances. The maximum brightness and current efficiency of all BPPF copolymers surpassed the PFO homopolymer. The best single‐layer device was based on 5BPPF, with a maximum brightness of 1532 cd/m² and current efficiency of 1.09 cd/A. Much higher efficiency could be achieved for multilayer EL devices of 5BPPF (ITO/PEDOT:PSS/PVK/polymer/TPBI/LiF/Al), which showed a maximum current efficiency of 10.01 cd/A. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1990–1999, 2010     

Organic electroluminescent devices using europium complex‐doped poly(N‐vinylcarbazole)

Electroluminescence (EL) properties of europium (Eu) complex‐doped poly(N‐vinylcarbazole) (PVK) were investigated. A device structure of glass substrate/indium‐tin oxide/hole‐injection layer/Eu complex‐doped PVK/hole‐blocking layer/electron transport layer/electron‐injection layer/Al was employed. Red emission originating from Eu complex was observed. Relatively high luminance of 50 cd/m² and an efficiency of 0.2% were obtained. Copyright © 2004 John Wiley & Sons, Ltd.     

带烷氧基的苯基蒎烯吡啶铱配合物在聚合物电致发光器件中的应用研究

采用旋涂法将一组带烷氧基的苯基蒎烯吡啶铱(Ⅲ)配合物(Ir(RO-pppy)₃)磷光材料掺杂到PVK中,制作出了聚合物电致发光器件:ITO/PE-DOT:PSS(40 nm)/PVK_0.7:PBD_0.3:(x%.)Ir-complex(80 nm)/CsF(1.5 nm)/Mg:Ag(200 nm).实验结果表明,带有长烷氧基链配体的铱(Ⅲ)配合物能表现出更好的器件行为,当掺杂浓度为3.2%时,器件的最高发光效率达19.9 cd/A(7.8 lm/W,9.1V),CIE为(0.20,0.56);器件最大亮度为15700 cd/m²(8.4V).通过对这组铱(Ⅲ)配合物的光物理行为及电化学性能的研究,考察了主体材料与配合物之间的能级配置以及能量转移的机理.     

Copolyphenylenes with pendant benzimidazolyl and diethanolaminohexyloxy groups: Synthesis and electron‐transporting application in PLEDs

Two new electron‐transporting copolyphenylenes P1NH and P2NH possessing balanced charges crucial to emission efficiency of polymer light‐emitting diodes (PLEDs) have been synthesized and applied as an electron‐transporting layer (ETL). The main chain structure is all para‐linkage for P1NH and both para‐ and meta‐linkage for P2NH , with the same pendant electron‐withdrawing benzimidazolyl and polar diethanolaminohexyloxy groups. Both copolymers possess excellent thermal stability (T _d > 300 °C, T _g > 100 °C) due to their rigid backbones. In addition, the pendant groups effectively lower LUMO (～ ?2.70 eV) and HOMO (～ ?5.70 eV) levels, resulting in improved electron‐transporting and hole‐blocking capabilities. Multilayer yellow‐emitting PLEDs with a configuration of ITO/PEDOT:PSS/SY/ETL/LiF/Al were successfully fabricated by the spin‐coating process. The maximum luminance and maximum current efficiency of the P1NH ‐based device were 12,881 cd/m² and 10.94 cd/A, respectively, superior to the performance of P2NH ‐based device (4938 cd/m², 3.70 cd/A) and the device without ETL (8690 cd/m², 2.78 cd/A). Current results indicate that P1NH is highly effective in enhancing electron transport and device performance. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 2494–2505     

Carbazole end‐capped pyrene starburst with enhanced electrochemical stability and device performance

Carbazole end‐capped starburst molecule based on pyrene core “4CzFP” was synthesized and characterized. The starburst material shows good film‐forming ability and bright blue fluorescence. In cyclic voltammetry test, 4CzFP shows a high highest occupied molecular orbital energy level of ?5.26 eV, indicating it has good hole‐injection ability. The material is quite stable under series of cyclic voltammetry scans, implying its good electrochemical stability. Single‐layered electroluminescent device takes on stable blue emission with a peak current efficiency of 0.84 cd/A. Double‐layered device by adding Poly(N‐vinylcarbazole) (PVK) as a hole‐injection layer does not show any improvement, indicating that 4CzFP could be efficiently used as the hole‐injection/light‐emitting layer. The device performance is largely improved by adding a thin TPBI electron‐injection/transporting layer. The peak efficiency reaches 3.28 cd/A and the maximum brightness is over 2200 cd/m². © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Copolyfluorenes containing pendant bipolar carbazole and 1,2,4‐triazole groups: Synthesis,characterization, and optoelectronic applications

Three novel copolyfluorenes ( P1 ‐ P3 ) containing pendant bipolar groups (2.5–7.7 mol %), directly linked hole‐transporting carbazole and electron‐transporting aromatic 1,2,4‐triazole, were synthesized by the Suzuki coupling reaction and applied to enhance emission efficiency of polymer light‐emitting diodes based on conventional MEH‐PPV. The bipolar groups not only suppress undesirable green emission of polyfluorene under thermal annealing, but also promote electron‐ and hole‐affinity of the resulting copolyfluorenes. Blending the bipolar copolyfluorenes with MEH‐PPV results in significant enhancement of device performance [ITO/PEDOT:PSS/MEH‐PPV+ P1 , P2 or P3 /Ca(50 nm)/Al(100 nm)]. The maximum luminance and luminance efficiency were enhanced from 3230 cd/m² and 0.29 cd/A of MEH‐PPV‐only device to 15,690 cd/m² and 0.81 cd/A (blend device with MEH‐PPV/ P3 = 94/6 containing about 0.46 wt % of pendant bipolar residues), respectively. Our results demonstrate the efficacy of the bipolar copolyfluorenes in enhancing emission efficiency of MEH‐PPV. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Intramolecular energy transferable (2,2‐diphenylvinyl)phenyl substituted poly(p‐phenylenevinylene) derivative with efficient photoluminescence and electroluminescence

A poly(p‐phenylenevinylene) (PPV) derivative containing a bulky (2,2‐diphenylvinyl)phenyl group in the side chain, EHDVP‐PPV, was synthesized by Gilch route. The reduced tolane‐bisbenzyl (TBB) defects, as well as the structure of the polymer, was confirmed by various spectroscopic methods. The intramolecular energy transfer from the (2,2‐diphenylvinyl)phenyl side group to the PPV backbone was studied by UV‐vis and photoluminescence (PL) of the obtained polymer and model compound. The polymer film showed maximum absorption and emission peaks at 454 and 546 nm, respectively, and high PL efficiency of 57%. A yellow electroluminescence (λ_max = 548 nm) was obtained with intensities of 6479 cd/m² when the light‐emitting diodes of ITO/PEDOT/EHDVP‐PPV/LiF/Al were fabricated. The maximum power efficiency of the devices was 0.729 lm/W with a turn‐on voltage of 3.6 V. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5636–5646, 2004