A dielectric study of poly(ethylene-co-vinylacetate)–poly(vinyl chloride) blends. I. Miscibility and phase behavior

Measurements of the complex permittivity were used to study miscibility and phase behavior in blends of poly(vinyl chloride) (PVC) with two random ethylene—vinyl acetate (EVA) copolymers containing 45 and 70 wt % of vinyl acetate. The dielectric β relaxation of the pure polymers and blends was followed as a function of temperature and frequency for different blend compositions and thermal treatments. Blends of EVA 70/PVC were found to be miscible for compositions of about 25% EVA 70 and higher. Blends of lower EVA 70 content showed evidence of two-phase behavior. EVA 45/PVC blends were found to be miscible only at the composition extremes; at intermediate compositions these blends were two-phase, partially miscible. Both blend systems showed lower critical solution temperature behavior. Phase separation studies revealed that in the EVA 45/PVC blends, PVC was capable of diffusing into the higher T_g phase at temperatures below the T_g of the upper phase. In the blends, ion transport losses were significant above the loss peak temperatures, and in the two-phase systems, often obscured the upper temperature loss process. It was shown possible, however, to correct the loss curves for this transport contribution.     

Miscibility of semirigid thermotropic liquid crystalline polycarbonate with poly(vinyl chloride)

Miscibility and morphology of polymer blends of semirigid thermotropic liquid crystalline (LC) polycarbonate (LCPC) with three commercial amorphous poly(vinyl chloride)s (PVC) having various molecular weights were investigated by means of differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). No phase separation was observed in the LCPC/PVC polymer blends. LCPC forms miscible polymer blends with the PVCs independent of molecular weight. The dynamic storage modulus of the LCPC/PVC polymer blends changes systematically with blend composition.     

Thermal degradation studies in poly(vinyl chloride)/poly(methyl methacrylate) blends

The miscibility, morphology, and thermal properties of poly(vinyl chloride) (PVC) blends with different concentrations of poly(methyl methacylate) (PMMA) have been studied. The interaction between the phases was studied by FTIR and by measuring the glass transition temperature (T_g) of the blends using differential scanning calorimetry. Distribution of the phases at different compositions was studied through scanning electron microscopy. The FTIR and SEM results show little interaction and gross phase separation. The thermogravimetric studies on these blends were carried out under inert atmosphere from ambient to 800 °C at different heating rates varying from 2.5 to 20 °C/min. The thermal decomposition temperatures of the first and second stage of degradation in PVC in the presence of PMMA were higher than the pure. The stabilization effect on PVC was found most significant with 10 wt% PMMA content in the PVC matrix. These results agree with the isothermal degradation studies using dehydrochlorination and UV-vis spectroscopic results carried out on these blends. Using multiple heating rate kinetics the activation energies of the degradation process in PVC and its blends have been reported.     

Segmental orientation in blends of poly(ϵ-caprolactone) with poly(vinyl chloride) and nitrocellulose

Binary blends of polycaprolactone (PCL) with poly(vinyl chloride) (PVC) and nitrocellulose (NC) have been shown to be compatible over a wide range of composition. In this study, segmental orientation was determined by dynamic, differential infrared dichroism for each component in the PVC and NC blends with PCL. In compatible amorphous blends, PCL orientation behavior was essentially the same as for the orientation of NC or the isotactic segments of PVC. Syndiotactic PVC segments showed higher orientations, reflecting the greater intrachain stiffness of the microcrystalline PVC phase. PCL segments in the blends where the PCL component was semicrystalline were found to exhibit orientation characteristics which were quite different from the orientation of the nitrocellulose and PVC components of the blends. By assuming that the NC orientation represented the response of the amorphous PCL, the orientation of the crystalline PCL was determined for a NC blend using a simple model of additive dichroism response. In PVC blends, a similar analysis using the amorphous-component response of PVC was made. In both cases the results from the dichroism model showed fair agreement with the PCL unit cell C-axis orientation from independent dichroism calculations.     

Morphology and properties of poly(vinyl chloride)–poly(butadiene-co-acrylonitrile) blends

The objective of this research was to study the structure-property relationships of two poly(vinyl chloride) (PVC)–poly(butadiene-co-acrylonitrile) (BAN) blends which exhibit differences in blend compatibility. Studies were carried out utilizing differential scanning calorimetry, dynamic mechanical testing, stress–strain, transmission electron microscopy (TEM), and infrared dichroism experiments at different temperatures. The BAN 31/PVC (BAN containing 31% acrylonitrile) system is considered to be nearly compatible as evidenced by T_g shifts, stress–strain results, orientation characteristics, and TEM micrographs. Similar experiments indicate that the BAN 44/PVC system is incompatible, and contains a mixed phase of BAN 44-PVC and a pure BAN 44 phase. The extent of heterogeneity in the compatible BAN 31/PVC system, however, plays an important role in the orientation characteristics of the blends.     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.     

聚ε-己内酯/聚氯乙烯球晶表面的XPS研究

聚合物薄膜在微电子领域中的应用日益增加.聚ε-己内酯/聚氯乙烯（PCL/PVC）是研究得最广泛的聚合物共混薄膜之一.PCL与PVC以一定比例混合时,可以形成环带球晶；同时,体系分为结晶PCL相及PCL/PVC非晶混溶相.用XPS和成象XPS分析技术,对PCL/PVC膜的表面化学组成和元素分布情况进行了研究.观察到PCL在薄膜表面富集.此外,成象XPS表明,PVC在球晶边界处富集,且球晶边界宽度约15 μm.     

Miscibility of poly(vinyl chloride) with poly(methyl-co-hexyl acrylate) and poly(methyl-co-2 ethyl hexyl acrylate)

The miscibility and phase behavior in blends of PVC with poly(methyl-co-hexyl acrylate)[MHA] and poly(methyl-co-2 ethyl hexyl acrylate)[MEH] were studied. It was found that PVC is miscible with MHA copolymers having a HA volume fraction from 0.30 to 0.92 and MEH copolymers having an EH volume fraction from 0.30 to 0.83 at 100°C. By applying the mean field theory to the phase diagrams of these blend systems, segmental interaction parameters which represent the binary interaction between different monomer units were estimated. The calculated values reflect the fact that the miscibility window observed for PVC/MHA and PVC/MEH blend systems was attributed to the effect of repulsion between different monomer units within the copolymer. To investigate the effect of specific interaction on the miscibility for these blend systems, an attempt was also made to describe the blend interaction parameter as a function of polar group concentration in the acrylate copolymer. The blend interaction parameter values exhibit a u-shaped curve as a function of the weight fraction of C?O group in the copolymer, and the lowest blend interaction parameter value appears at about 0.24 C?O weight fraction.     

Studies of photooxidative degradation of poly(vinyl chloride)/poly(ethylene oxide) blends

The photooxidative degradation of blends (in a full range of compositions) of amorphous poly(vinyl chloride) (PVC) with semicrystalline poly(ethylene oxide) (PEO) in the form of thin films is investigated using absorption spectroscopy (UV–visible and Fourier transform infrared) and atomic force microscopy (AFM). The amount of insoluble gel formed as a result of photocrosslinking is estimated gravimetrically. It is found that the PVC/PEO blendsí susceptibility to photooxidative degradation differs from that pure of the components and depends on the blend composition and morphology. Photoreactions such as degradation and oxidation are accelerated whereas dehydrochlorination is retarded in blends. The photocrosslinking efficiency in PVC/PEO blends is higher than in PVC; moreover, PEO is also involved in this process. AFM images showing the lamellar structure of semicrystalline PEO in the blend lead to the conclusion that the presence of PVC does not disturb the crystallization process of PEO. The changes induced by UV irradiation allow the observation of more of the distinct PEO crystallites. This is probably caused by recrystallization of short, more mobile chains in degraded PEO or by partial removal of the less stable amorphous phase from the film surface. These results confirm previous information on the miscibility of PVC with PEO. The mechanism of the interactions between the components and the blend photodegradation are discussed. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 585–602, 2004     

Miscibility of poly(vinyl chloride) with chitin derivatives having poly(2-methyl-2-oxazoline) side chains

Binary blends of poly(vinyl chloride) (PVC) and chitin-graft-poly(2-methyl-2-oxazoline) showed miscibility in the blend fraction range of the latter lower than ca. 10 wt.-%. The glass transition temperature of PVC, which was determined by differential scanning calorimetry, changed to lower temperatures with increasing modified chitin contents up to 10 wt.-%. Segmental interaction between PVC and the graft copolymer was confirmed by the carbonyl stretching band shift in the FT-IR analysis.     

Compatibility of poly(vinyl chloride) with polyalkyleneoxides. II. Poly(propylene oxide) and poly(tetramethylene oxide)

This study [Part II of a series dealing with the compatibility of polyalkyleneoxides with poly(vinyl chloride)] examines blends of PVC with poly(propylene oxide) (PPrO) and poly(tetra-methylene oxide) (PTMO), covering the entire composition range. Morphological, dynamic mechanical and thermal properties investigated indicate that PVC/PPrO blends are incompatible, whereas the PVC/PTMO system shows miscibility in the melt. For this polyblend and at high polyether compositions where the Hoffman–Weeks analysis can be applied, T_m equilibrium data allow the determination of the thermodynamic interaction parameter, χ₁₂ = ?0.15. Experimental compatibility data of all polyether-PVC pairs investigated in Parts I and II are also used to test various blend miscibility prediction schemes, using solubility parameter theory and recent theory on copolymer-copolymer miscibility.     

Thermal conductivity of poly(vinyl chloride)/polycaprolactone blends

Thermal diffusivity, heat capacity, and density of polyvinyl chloride/polycaprolactone (PVC/PCL) blends were measured by the laser flash method, DSC, and pycnometry, respectively. The thermal conductivity of the PVC/PCL blends was determined from the results. The miscibility of the blend and crystallinity of PCL were determined by DSC. The effect of blend structure on thermal conductivity is discussed. The phase compositions of the PVC/PCL blends are of three types depending on PCL content: i.e., up to 33%, from 33 to 70%, and above 70% PCL by weight. Thermal conductivity, thermal diffusivity, and heat capacity of the PVC/PCL blends are strongly affected by the phase composition of the blend, which changes in a complicated way with PCL content. © 1994 John Wiley & Sons, Inc.     

The influence of core-shell structured modifiers on the toughness of poly (vinyl chloride)

The core-shell structured grafted copolymer particles of polybutadiene grafted polymethyl methacrylate (PB-g-PMMA, MB) were prepared by emulsion polymerization. The MB particles were used to modify poly (vinyl chloride) (PVC) by melt blending. The mechanical properties of the PVC blends were investigated. The micro-morphology of the PVC blends was observed by scanning electron microscopy (SEM). The results indicated that the samples with the best impact strength could be obtained when the core-shell weight ratio of PB to PMMA is lower than 93:7, the mechanical properties correlated well with SEM morphologies, the addition of modifier with the ratio core to shell of 93:7 could reduce the domain size of the dispersed phase. Furthermore, the compatibility and properties of the blends were greatly enhanced and improved. The modifier particles could be well dispersed in the PVC matrix.     

Investigation of polymer miscibility by spectroscopic methods V. Effect of molecular weight and block copolymerization of syndiotactic poly(methyl methacrylate) on its miscibility with poly(vinyl chloride)

Investigated by nonradiative energy transfer (NRET), the state of mixing of PVC and s.PMMA which is on the dimensional scale of a few nanometers is significantly affected by the chain length. When PVC is blended with s.PMMA of increasing molecular weight (MW), the longest chains of s.PMMA are likely to segregate from a homogeneous blend formed by PVC and low-MW s.PMMA. The phase separation should therefore be of purely entropic origin and strongly dependent on both the relative percentage and the chain length of each component. These results are in qualitative agreement with conclusions previously drawn from DSC and transmission electron microscopy. NRET is a more powerful tool in probing heterogeneities compared to DSC and the thermally stimulated depolarization current method; it provides evidence against the previously suggested model of a 1:1 PVC/s.PMMA aggregate.     

共混方法对聚氯乙烯/聚丙撑碳酸酯相容性影响

本文分别用溶液法和熔融法制得聚氯乙烯（PVC）与聚丙撑碳酸酯（PPC）共混试样，用DSC证明PVC／PPC共混物不相容，但它们不相容的程度受分子量、共混比例等因素的影响，并根据玻璃化转变温度（Tg）计算出溶液共混试样PPC富相中PVC的重量百分含量。NBR／PPC弹性体作偶联剂对PVC／PPC共混体系具有较好的增容作用，共混物中PPC的用量及分子量对共混体系性能有一定的影响。     

Phase behavior and morphology in epoxy resin/poly(L-lactide) blends. Comparison with epoxy resin/poly(L,D-lactide) blends

Thermoset/thermoplastic blends were prepared with epoxy–aromatic diamine mixtures and poly(L-lactide) (PLLA), as semicrystalline thermoplastic, in concentrations ranging from 4 to 25 wt.%. In some cases, poly(L,D-lactide) (PDLLA), an amorphous thermoplastic, was used instead for comparative purposes. Diglycidyl ether of bisphenol-A (DGEBA) was employed as epoxy resin and 4,4′-diaminodiphenylmethane (DDM) as curing agent. Phase behavior and morphology were studied during curing at 140 °C. Initially, all blends were homogeneous; however, the curing reaction of the epoxy resin caused a liquid–liquid phase separation. A co-continuous morphology was formed at the beginning of the phase separation in all the considered blend compositions. Blends evolved to a particle/matrix structure or to a phase-inverted structure depending on the initial blend composition. At 140 °C, crystallization only occurred in blends with 16 and 25 wt.% PLLA. This crystallization originates changes in the surface of the epoxy-rich droplets developed with the phase separation.     

Studies on phase separation and coarsening in blends of poly(vinylidene-fluoride) and poly(ethyl-acrylate)

The phase diagram of blends of poly(vinylidene fluoride) and poly (ethyl acrylate) was established by X-ray scattering, optical microscopy and calorimetric techniques. Structure formation, involving phase separation and coarsening was analyzed as a function of temperature variations and annealing times. The variations consisted of increasing or decreasing the temperature stepwise, starting either in the one-phase or in the two-phase state of the melt.Dedicated to Prof. R. Bonart (Univ. Regensburg) on the occasion of his 60^th birthday     

Degradation of polymer mixtures. VII. Blends of poly(vinyl acetate) with polystyrene

The degradation of films containing both PVA and PS has been investigated for comparison with the behavior already reported for PVC/PS blends. The presence of PS had little, if any, effect on the behavior of PVA, but PVA had an effect similar to that of PVC on the degradation of PS. Styrene production was retarded in the blend, compared to PS alone, and an increase in the rate of chain scission was observed for a high molecular weight sample. The molecular weight effect, however, was much smaller than in corresponding experiments with PVC/PS blends. Interference with intermolecular transfer in PS is again advanced as the probable explanation of the stabilization of PS.     

Degradation of polymer mixtures. IV. Blends of poly(vinyl acetate) with poly(vinyl chloride) and other chlorine-containing polymers

The degradation of the binary polymer blends, poly(vinyl acetate)/poly(vinyl chloride), poly(vinyl acetate)/poly(vinylidene chloride) and poly(vinyl acetate)/polychloroprene has been studied by using thermal volatilization analysis, thermogravimetry, evolved gas analysis for hydrogen chloride and acetic acid, and spectroscopic methods. For the first two systems named, strong interaction occurs in the degrading blend, but the polychloroprene blends showed no indication of interaction. In the PVA/PVC and PVA/PVDC blends, hydrogen chloride from the chlorinated polymer causes substantial acceleration in the deacetylation of PVA. Acetic acid from PVA destabilizes PVC but has little effect in the case of PVDC because of the widely differing degradation temperatures of PVA and PVDC. The presence of hydrogen chloride during the degradation of PVA results in the formation of longer conjugated sequences, and the regression in sequence length at high extents of deacetylation found for PVA degraded alone is not observed.     

Biodegradation of plasticized poly(vinyl chloride) containing cellulose

The plasticized poly(vinyl chloride) (PVC‐P) and its blend with cellulose (PVC‐P/cell) were prepared by means of extrusion. The samples were then biodegraded in forest soil as well as in soil enriched with cellulolytic microorganisms. Moreover, the samples were vaccinated with chosen species of fungi whose direct effect on polymer was then observed. The course of biodegradation was monitored in terms of, and by means of the following: weight loss, carbon dioxide evolved, attenuated total reflectance infrared (FTIR‐ATR) spectroscopy, gel permeation chromatography (GPC), as well as visual and microscopic observation (OM, SEM). The mechanical properties of samples were studied using the standard tensile tests. It was found that biodegradation in soil occurs in PVC‐P and this process is accelerated in the composition of PVC‐P with cellulose. The biodecomposition yield of PVC‐P/cellulose blends (calculated as relative percentage weight loss) is several dozen times higher than that of PVC‐P. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 903–919, 2007