苯乙烯-甲基丙烯酸甲酯的高温阴离子溶液共聚

以正丁基锂(n-BuLi)为引发剂、四氢呋喃(THF)为极性调节剂,采用具有较大空间位阻和特定电荷环境的P配合物作为抑制剂,在80℃下实现了苯乙烯(St)与甲基丙烯酸甲酯(MMA)的阴离子嵌段共聚.采用GPC、FT-IR、1H-NMR等手段对共聚物的结构及分子量进行了分析.结果表明:共聚物中各链节的分子量与设计分子量接...     

乙烯基单体-N-苯基马来酰亚胺共聚物序列结构研究

用NMR谱研究了甲基丙烯酸甲酯(MMA)-N-苯基马来酰亚胺(PMI)、苯乙烯(St)-PMI共聚物的序列结构.结果表明,MMA-PMI共聚物单元属无规序列分布,St-PMI共聚物单元属交替序列分布.由¹HNMR结果可得MMA-PMI共聚物空间立构部分信息,由¹³CNMR三单元组实验结果算得的序列长度与末端基理论计算结果一致,且MMA-PMI共聚物链属一级Markov链.由St-PMI共聚物序列长度与末端基理论计算结果的偏差提出更为合理的增长基元反应.     

水分散体系中苯乙烯和甲基丙烯酸甲酯梯度共聚物的合成与表征

以2-溴代异丁酸乙酯(EBiB)为引发剂,CuBr/CuBr₂/1,10-邻二氮菲(phen)为复合催化剂,十二烷基磺酸钠(SLS)为乳化剂,考察了水分散体系中苯乙烯(St)和甲基丙烯酸甲酯(MMA)的原子转移自由基共聚合的可控性和相对反应活性.在此基础上,通过反应进料法在水分散体系中进行了St和MMA的梯度共聚合,反应表现出“活性”聚合的特征,即所得共聚物的数均分子量随着单体转化率的增加而增大,分子量分布较窄(M_w/M_n<1.50).用¹HNMR跟踪分析了聚合反应过程中共聚物微观组成的变化规律,结果表明,共聚物链中MMA链节的累积含量和瞬时含量都随着共聚物相对链长的增加而增加,即随着聚合物相对链长的增加共聚物的微观组成从St链节占主导地位逐渐变化为以MMA链节占主导地位,表明确实形成了St和MMA的梯度或渐变共聚物.     

乙烯基单体/N-取代马来酰亚胺共聚合动力学

详细研究了聚合温度、引发剂用量、单体配比对苯乙烯(St)/N-苯基马来酰亚胺(PMI)共聚合动力学的影响.对St、甲基丙烯酸甲酯(MMA)和丙烯腈(AN)等单一或混合单体与PMI、N-环己基马来酰亚胺(ChMI)和N-邻氯苯基马来酰亚胺(o-CPMI)的共聚合进行了研究,并讨论了单体结构的影响.     

含氟丙烯酸酯与苯乙烯共聚物的RAFT合成及表征

通过可逆加成-断链链转移(RAFT)溶液聚合,以三硫代碳酸酯为RAFT试剂,偶氮二异丁腈(AIBN)为引发剂,1,4-二氧六环为溶剂,制备甲基丙烯酸(2,2,2-三氟)乙酯(TFEMA)和苯乙烯(St)共聚物.详细研究了不同引发剂的用量、RAFT试剂与引发剂摩尔比以及聚合温度等实验条件对聚合反应过程的影响.通过GPC、FTIR测试共聚物的分子量、分子量分布和分子结构,并用静态接触角仪和AFM分别表征聚合物膜的接触角、表面能及膜的表面形貌.     

具有预期结构的苯乙烯与丙烯酸丁酯接枝共聚物的合成与表征

通过苯乙烯 (St)与 4 对氯甲基苯乙烯 (CMS)进行氮氧稳定自由基共聚合反应 ,合成了二元共聚物P(St co CMS) ,并以此共聚物引发丙烯酸丁酯进行原子转移自由基聚合 ,成功地合成了结构明晰的以聚苯乙烯为主链、聚丙烯酸丁酯为支链的接枝共聚物 ,研究了共聚合反应动力学 .P(St co CMS)和接枝共聚物的结构通过1 H NMR得到确认 ,并表征了接枝共聚物平均侧链数目和平均侧链长度     

丙烯酰胺-苯乙烯双亲嵌段共聚物水溶液的表面活性及增溶性

在微乳液介质中制备了系列的丙烯酰胺 (AM)与苯乙烯 (St)的双亲嵌段共聚物 (PAM b PSt) ,用紫外分光光度法测定了共聚物的组成 ,用乌氏粘度计测定了共聚物的特性粘数 [η],并用其相对表征共聚物的分子量大小 .重点研究了双亲嵌段共聚物 (PAM b PSt)疏水链段在水溶液中的缔合行为、共聚物的表面活性及其对有机物的增溶性能 ,考察了共聚物分子组成 (疏水链段含量 )与分子量对其表面活性与增溶性能的影响规律 .研究结果表明 ,由于疏水链段的憎水性 ,PAM b PSt的分子链在水溶液表面会形成表面吸附 ,从而降低水溶液的表面张力 ;而在水溶液中 ,在疏水相互作用下 ,PAM b PSt分子链中的苯乙烯疏水链段会形成分子间或分子内的胶束 ,烃类有机物可增溶其中 ;疏水链段含量越大 ,分子量越小 ,PAM b PSt的表面活性与增溶性能越强     

AN/St悬浮共聚体系中AN在水/油两相间分配及其对共聚物组成的影响

研究了丙烯腈/苯乙烯(AN/St)悬浮共聚体系中AN在水/油两相间的分配及其对AN/St共聚物组成的影响.结果表明,AN分配于水/油两相间,使油相AN的含量低于相同单体配料比的本体聚合,导致生成的AN/St共聚物组成偏离本体共聚.为了准确预测进而控制AN/St悬浮共聚物的组成,提出了在考虑AN相分配的基础上计算AN/St悬浮共聚物组成的模型.计算结果与实验值一致,计算中用到的油相实际竞聚率与本体聚合相同,但该悬浮聚合的表观竞聚率随水/油比的变化而发生较大改变.     

一种大分子引发剂的引发作用研究

将溶液聚合合成的α-甲基苯乙烯(AMS)和甲基丙烯酸缩水甘油酯(GMA)的低相对分子质量共聚物(计为PAG)作为大分子引发剂,分别研究了PAG引发单体甲基丙烯酸甲酯(MMA)和苯乙烯(St)的本体聚合反应,采用GPC和FTIR等手段对聚合产物进行了表征.研究结果表明,在加热到一定温度时,PAG具有引发作用,可以引发MMA和St进行本体聚合反应;聚合产物具有再引发功能,且其分子量与聚合物产率和聚合反应时间之间均有较好的线性关系.     

在α-甲基苯乙烯二聚体调节作用下的苯乙烯-丙烯腈乳液共聚

<正> 由于苯乙烯(St)和丙烯腈(AN)竞聚率的差异,在乳液共聚中所得产物为组成不均匀的共聚物,因此一般在反应后期通过复杂计算和实验验证补加消耗快的单体,或采用回收大量单体等方法得到组成均匀的共聚物。St-AN乳液共聚物的分子量较大,产物不     

New potentially environmentally friendly copolymer of styrene and maleic acid—castor oil monoester

The maleic acid‐castor oil monoester (MACO) was synthesized and was used as monomer to synthesize a new potentially environmentally friendly copolymer of styrene and MACO (poly‐St/MACO) by suspension polymerization. Under the appropriate conditions, the poly‐St/MACO with yield of 81%, number average molecular weight of 44100 g/mol, and molecular weight distribution of 1.5 could be obtained. The chemical structures of the MACO and resulting copolymer were confirmed by Mass Spectrometry Infrared Spectroscopy and Nuclear Magnetic Resonance Spectroscopy H[1]. The results of thermogravimetric analysis and biodegradation test showed the poly‐St/MACO can be used as a new potentially environmentally friendly material with excellent thermal stability. Copyright © 2011 John Wiley & Sons, Ltd.     

氯乙烯/N-苯基马来酰亚胺共聚物组成控制和优化

研究了氯乙烯 /N 苯基马来酰亚胺 (VC/PMI)共聚物组成随转化率的变化 ,体系中共聚物的累积组成偏差小于 0 0 5或 0 1的单体配比范围很小 ,采用加入第三单体丙烯腈 (AN)的方法进行改善 ,并以PMI在共聚物中的累积组成偏差作为控制参数 ,得到了PMI在共聚物中的累积组成偏差小于 0 0 5和 0 1的VC/PMIlAN较优的配比范围 .结合悬浮聚合工艺的特点 ,确定了VC/PMI/AN悬浮共聚的最佳单体配比范围为f1=0 72～ 0 84 ,f2 =0 0 2～ 0 0 4 ,f3 =0 1 2～ 0 2 4 .     

马来酸酐和苯乙烯的可逆加成-断链链转移聚合及新型嵌段共聚物的合成

马来酸酐和苯乙烯是被广为研究的一对电荷转移复合物 (Ｃｈａｒｇｅｔｒａｎｓｆｅｒｃｏｍｐｌｅｘ,简称ＣＴＣ) ,而且能通过通常的自由基聚合发生交替共聚[1] .所得的聚合物由于酸酐基团的存在 ,很易进行大分子改性得到具有某些特殊功能的高分子 .不过 ,所得共聚物的分子量难以控制且分子量分布也较宽 .近年来发展起来的“活性” 可控自由基聚合越来越为人们所关注 ,因为采用这种方法不仅可对聚合物的分子量进行设计 ,同时分子量分布也较窄 ,也不需要活性离子型聚合那样严格的聚合条件 .关于烯类单体的活性自由基聚合迄今主要有氮氧自由基…     

Preparation of Quaternary Amphiphilic Block Copolymer PMA-b-P (NVP/MAH/St) and Its Application in Surface Modification of Aluminum Nitride Powders

Poly(methyl acrylate)-b-poly(N-vinyl pyrrolidone/maleic anhydride/styrene) (PMA-b-P (NVP/MAH/St)) quaternary amphiphilic block copolymer prepared by reversible addition-fragmentation chain transfer (RAFT) was used to improve the anti-hydrolysis and dispersion properties of aluminum nitride (AIN) powders that were modified by copolymers. Its structure was characterized by Fourier transform infrared spectroscopy (FT-IR) and Hydrogen nuclear magnetic spectroscopy (¹H-NMR). The results demonstrate that the molecular weight distribution of the quaternary amphiphilic block copolymers is 1.35–1.60, which is characteristic of controlled molecular weight and narrow molecular weight distribution. Through charge transfer complexes, NVP/MAH/St produces a regular alternating arrangement structure. After being treated with micro-crosslinking, AlN powder modified by copolymer PMA-b-P(NVP/MAH/St) exhibits outstanding resistance to hydrolysis and can be stabilized in hot water at 50 °C for more than 14 h, and the agglomeration of powder particles was improved remarkably.     

Isospecific copolymerization of styrene and a styrene‐terminated polyisoprene macromonomer with the Ni(acac)2/MAO catalyst

The copolymerization of styrene (St) with a styrene‐terminated polyisoprene macromonomer (SIPM) by a nickel(II) acetylacetonate [Ni(acac)₂] catalyst in combination with methylaluminoxane (MAO) was investigated. A SIPM with a high terminal degree of functionalization and a narrow molecular weight distribution was used for the copolymerization of St. The copolymerization proceeded easily to give a high molecular weight graft copolymer. After fractionation of the resulting copolymer with methyl ethyl ketone, the insoluble part had highly isotactic polystyrene in the main chain and polyisoprene in the side chain. Lowering the MAO/Ni molar ratio and the polymerization temperature were favorable to producing isospecific active sites. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1241–1246, 2000     

Synthesis of graft copolymer from copolymerization of styrene‐terminated poly(ethylene oxide) macromonomer and styrene with CpTiCl3/methylaluminoxane catalyst

Copolymerization of styrene (St) and St‐terminated poly(ethylene oxide) macromonomer (SEOM) with CpTiCl₃/methylaluminoxane (MAO) catalyst in toluene was investigated. The copolymerization of St and SEOM proceeded easily to give a graft copolymer consisting of syndiotactic polystyrene as the main chain and hydrophilic poly(ethylene oxide) as the side chain. A number of side chains in the graft copolymer could be controlled by the amount of SEOM in the feed. The reactivity of SEOM was determined from copolymerization of St and SEOM with the CpTiCl₃/MAO catalyst, and the reactivity of SEOM depended on the molecular weight of SEOM. The thermal properties of the graft copolymer such as the melting temperature were influenced by the introduction of SEOM. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2904–2910, 2004     

钴系丁二烯苯乙烯共聚合及共聚物序列结构的研究

<正> 高顺式丁苯胶的合成研究已有二、三十年的历史。除了存在共聚物的苯乙烯结合量偏低以及混有一定量的均聚苯乙烯等问题外,共聚物分子链上各结构单元偏离无规分布可能是一个重要原因。 1983年古川淳二等曾用C-NMR方法对镍系高顺式丁苯共聚物分子链上顺-1,4(C)、反-1,4(T)、1,2结构(V)、苯乙烯(St)四种结构单元的键接几率做过分析。例如,     

不饱和环缩醛与苯乙烯的原子转移自由基共聚合反应

不饱和环状单体与烯类单体共聚所得的共聚物 ,已经或正在开发成一系列新的产品 .例如 ,水解后得到末端带有—OH,— SH,—COOH等官能团的聚苯乙烯、聚乙烯、聚甲基丙烯酸甲酯等的低聚物[1] ,用于制备新型聚酯和聚氨酯 ;与乙烯的共聚物可在细菌作用下彻底分解成脂肪酸或醇 ,可赋予聚合物生物降解活性 ;与双甲基丙烯酸酯等的共混物 ,可用于制作高强度补牙材料[2 ] 等 .以前报道的不饱和环状单体与烯类单体的共聚反应 ,均为无规共聚 ,而且是普通自由基引发聚合 ,不能控制分子量 ,分子量分布很宽 .原子转移自由基聚合是近几年发展起来的实现…     

Studies on microstructure and aqueous solution properties of block copolymer of acrylamide-styrene

Three series of block copolymers of acrylamide (AM) and styrene (St) as hydrophobic comonomer with varied microstructures were prepared in microemulsion medium by changing feed ratio of monomers, ratio of St to surfactant, and amount of initiator, respectively. The effects of microstructure factors of the amphiphilic block copolymers PAM-b-PSt on their aqueous solution properties were investigated by fluorescence probe technique and surface tension measurement in detail. The experimental results show that the aqueous solution properties of PAM-b-PSt are strongly dependent on their microstructure factors, such as the length and content of PSt hydrophobic blocks in the copolymers and their molecular weight. It was found that the main microstructure factors which effect the hydrophobic association behavior of the copolymer PAM-b-PSt are the length and content of PSt hydrophobic blocks in the copolymer, whereas the hydrophobic association behavior of the copolymer is not affected nearly so much by molecular weight in more dilute regions. At the same time, it was also found that the main microstructure factors which affect the surface activity of the copolymer are the content of PSt hydrophobic blocks in the copolymer and molecular weight, whereas the length of PSt blocks in copolymer does not affect surface activity of the copolymer nearly so much under fixed content of PSt hydrophobic blocks and molecular weight in the copolymer.