Deposition and characterization of binary Al2O3/SiO2 coating layers on the surfaces of rutile TiO2 and the pigmentary properties

Binary Al₂O₃/SiO₂-coated rutile TiO₂ composites were prepared by a liquid-phase deposition method starting from Na₂SiO₃·9H₂O and NaAlO₂. The chemical structure and morphology of binary Al₂O₃/SiO₂ coating layers were investigated by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, TG-DSC, Zeta potential, powder X-ray diffraction, and transmission electron microscopy techniques. Binary Al₂O₃/SiO₂ coating layers both in amorphous phase were formed at TiO₂ surfaces. The silica coating layers were anchored at TiO₂ surfaces via Si-O-Ti bonds and the alumina coating layers were probably anchored at the SiO₂-coated TiO₂ surfaces via Al-O-Si bonds. The formation of continuous and dense binary Al₂O₃/SiO₂ coating layers depended on the pH value of reaction solution and the alumina loading. The binary Al₂O₃/SiO₂-coated TiO₂ composites had a high dispersibility in water. The whiteness and brightness of the binary Al₂O₃/SiO₂-coated TiO₂ composites were higher than those of the naked rutile TiO₂ and the SiO₂-coated TiO₂ samples. The relative light scattering index was found to depend on the composition of coating layers.     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Promotion of surface SOx on the selective catalytic reduction of NO by hydrocarbons over Ag/Al2O3

The promotion of sulfur oxides on the selective catalytic reduction (SCR) of NO by hydrocarbons in the presence of a low concentration of sulfur oxides over Ag/Al₂O₃ has been investigated by a flow reaction test and in situ infrared spectroscopy. When the C₃H₆ (or C₁₀H₂₂) + NO + O₂ feed-flow reaction was tested, maximum NO reduction was below 30% over fresh Ag/Al₂O₃. After the addition of SO₂ to the feed flow, conversion increased slightly. Conversion increased further after SO₂ was cut-off from the feed flow. This demonstrated that the increase in NO reduction activity of the catalyst was related to SO_x adsorbed on the catalyst. SO_x adsorbed on the catalytic surface (1375 cm⁻¹) was detected by IR spectroscopy and was stable within the temperature range. NCO species, as an intermediate in NO reduction, on SO_x-adsorbed Ag/Al₂O₃ in a C₃H₆ + NO + O₂ feed flow was observed in in situ IR spectra during the elevation of the reaction temperature from 473 to 673 K, while it was only observed at 673 K on fresh Ag/Al₂O₃ under the same experimental conditions. We suggest that SO_x in low concentrations depressed the combustion of reductants by contaminating hydrocarbon combustion active sites on the catalyst, resulting in an increase in NO reduction efficiency of the reductants.     

The improvement of Al2O3/AlGaN/GaN MISHEMT performance by N2 plasma pretreatment

This paper discusses the effect of N 2 plasma treatment before dielectric deposition on the electrical performance of a Al2O3 /AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor(MISHEMT),with Al2O3 deposited by atomic layer deposition.The results indicated that the gate leakage was decreased two orders of magnitude after the Al2O3 /AlGaN interface was pretreated by N 2 plasma.Furthermore,effects of N 2 plasma pretreatment on the electrical properties of the AlGaN/Al2O3 interface were investigated by x-ray photoelectron spectroscopy measurements and the interface quality between Al2O3 and AlGaN film was improved.     

Er3+掺杂SiO2复合的Al2O3粉末结构及光致发光特性

采用溶胶-凝胶(sol-gel)工艺制备0.1 mol% Er³⁺掺杂Al₂O₃体系和SiO₂-Al₂O₃复合体系粉末. 实验结果表明：5 mol%的SiO₂复合加入Al₂O₃抑制γ→θ和θ→α相转变. 掺0.1 mol%Er³⁺:Al₂O₃体系粉末，900℃烧结，在1.47—1.63μm波段内光致发光(PL)谱为中心波长1.53 μm、半高宽56 nm的单一宽峰，1000—1200℃烧结，劈裂为多峰PL谱. 掺0.1 mol%Er³⁺:SiO₂-Al₂O₃复合体系粉末，在高达1200℃烧结，仍保持中心波长1.53 μm的单一宽峰PL谱，由于—OH更完全的脱除，PL强度较900℃烧结Al₂O₃体系，SiO₂-Al₂O₃复合体系均提高1个数量级. 关键词： 2-Al₂O₃复合体系')" href="#">SiO₂-Al₂O₃复合体系 掺铒 溶胶-凝胶工艺 光致发光     

Investigation on densification of Al2O3/B4C ceramic by ab initio calculation and experiment

Compared to experiment, the adsorption energies, bonding properties, and electronic structure of two different Al₂O₃/B₄C bridge sites with seven different Al₂O₃ surfaces are investigated by ab initio periodic density functional theory. The Al₂O₃/B₄C ceramic sintered in Ar is synthesized and measured by XRD and TEM. The calculated results reveal that the densification of O_bridge site of Al₂O₃/B₄C surface is better than that of Al_bridge. The Al₂O₃ (1 1 3)/B₄C with O_bridge is the most favorable and stable. The electronic structure shows that the electron hybridization exists between Al, O atoms and C, B atoms. The results indicate that the calculated results are in good agreement with the experiment.     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Al2O3-Y2O3-ZrO2三相复合陶瓷的介电谱研究

采用传统的固相反应法,在1400–1500 ℃下烧结,制备得到Al₂O₃-Y₂O₃-ZrO₂三相复合陶瓷.样品的结构、形貌和电性能分别用X射线衍射(XRD)、扫描电子显微镜(SEM)及介电谱表征.XRD表明此三相复合体系无其他杂相,加入Y₂O₃及ZrO₂后使得Al₂O₃成瓷温度降低;SEM表明此体系晶粒直径为200–500 nm,并且样品随烧结温度的升高而变得更加致密,晶界更加清晰;介电损耗谱中出现峰值弛豫现象,根据Cole-Cole复阻抗谱得出其为非德拜弛豫. 关键词： 2O₃-Y₂O₃-ZrO₂三相陶瓷')" href="#">Al₂O₃-Y₂O₃-ZrO₂三相陶瓷 介电弛豫 阻抗谱 热导率     

Study of Al2O3/TiO2 reflectivity enhancing bi-layer films on bright aluminium substrates

Al₂O₃/TiO₂ bi-layer films on aluminium substrates have been obtained by combining anodising and TiO₂ sol-gel deposition. The reflectivity enhancing properties of these Al₂O₃/TiO₂ bi-layer films have been studied in relation to the refractive index and thickness of the Al₂O₃ and TiO₂ single-layers. It is shown that a significant improvement of reflectivity can be achieved by a proper optimisation of the bi-layer elaboration parameters.     

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

Fe₂O₃/Al₂O₃ catalysts were prepared by solid state reaction method using α-Fe₂O₃ and γ-Al₂O₃ nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ₃ and τ₄ are attributed to positronium annihilation in two types of pores distributed inside Al₂O₃ grain and between the grains, respectively. With increasing Fe₂O₃ content from 3 wt% to 40 wt%, the lifetime τ₃ keeps nearly unchanged, while the longest lifetime τ₄ shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe₂O₃ content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ₄ is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Photoluminescence and thermoluminescence of Ce and Eu in Ca2Al2SiO7 matrix

The Ca₂Al₂SiO₇ samples doped with Ce³⁺ and Eu²⁺ are synthesized via a high temperature solid-state reaction. Ca₂Al₂SiO₇: Ce³⁺ emits a strong UV-violet emission while Ca₂Al₂SiO₇: Eu²⁺ emits a blue-green emission. The Stokes shift of the latter is greater due to a stronger crystal repulsion from ligands to Eu²⁺ ions. Ca₂Al₂SiO₇: Ce³⁺ exhibits a stronger initial intensity and longer duration of afterglow due to the higher liberated probability of the trapped carriers. The thermoluminescence curves reveal that at least three traps exist in the phosphors. Ca²⁺ vacancies may enhance the electron trapping and then lead to a stronger afterglow. A possible explanation will be provided.     

Synthesis and characterization of Sr3Al2O6：Eu2＋, Dy3＋ phosphors prepared by sol-gel-combustion processing

A type of red luminescent Sr3Al2O6:Eu2+, Dy3+ phosphor powder is synthesised by sol-gel-combustion processing, with metal nitrates used as the source of metal ions and citric acid as a chelating agent of metal ions. By tracing the formation process of the sol-gel, it is found that it is necessary to reduce the amount of NO3- by dropping ethanol into the solution for forming a stable and homogeneous sol-gel. Thermogravimetric and Differential Scanning Calorimeter Analysis, x-ray diffractionmeter, scanning electron microscopy and photoluminescence spectroscopy are used to investigate the luminescent properties of the as-synthesised Sr3Al2O6:Eu2+, Dy3+. The results reveal that the Sr3Al2O6 crystallises completely when the combustion ash is sintered at 1250 C. The excitation and the emission spectra indicate that the excitation broadband lies mainly in a visible range and the phosphors emit a strong light at 618 nm under the excitation of 472 nm. The afterglow of (Sr0.94Eu0.03Dy0.03)3Al2O6 phosphors sintered at 1250 ℃ lasts for over 1000 s when the excited source is cut off.     

Dy含量对红色长余辉发光材料Sr3Al2Ｏ6:Eu2＋,Dy3＋性能的影响

采用溶胶凝胶法制备了Sr₃Al₂Ｏ₆:Eu^2＋,Dy^3＋红色长余辉发光材料,利用X射线衍射仪对材料的物相进行了分析,结果表明,1200℃下制备的样品的物相为Sr₃Al₂Ｏ₆,少量的Eu和Dy掺杂没有影响样品的相组成.采用荧光分光光度计、照度计测定了样品的发光特性.结果表明Sr₃Al₂Ｏ关键词： 红色长余辉 3Al₂Ｏ₆')" href="#">Sr₃Al₂Ｏ₆ 溶胶凝胶法     

有机金属化学气相沉积法制备的Ni/Al2O3纳米复合材料的氢吸附

研究了通过有机金属化学气相沉积技术及单源分子前躯体方法制备的Ni/Al₂O₃纳米复合材料的氢吸附(存储). 在冷壁的有机金属化学气相沉积反应器中,通过降解Ni(acac)₂粉末基底上的[H₂Al(OtBu)]₂制备的Ni/Al₂O₃纳米复合材料. 通过X射线粉末衍射、扫描电镜、透射电镜以及能量色散型X射线荧光光谱等技术表征该复合材料. 采用自制Sievert's设备研究该复合材料的氢吸附(存储),可以储存约2.9%(重量比)的氢.     

Microstructure and mechanical properties of Al2O3-Al composite coatings deposited by plasma spraying

Al₂O₃ and Al₂O₃-Al composite coatings were prepared by plasma spraying. Phase composition of powders and as-sprayed coatings was determined by X-ray diffraction (XRD), while optical microscopy (OM) and scanning electron microscopy (SEM) were employed to investigate the morphology of impacted droplets, polished and fractured surface, and the element distribution in terms of wavelength-dispersive spectrometer (WDS). Mechanical properties including microhardness, adhesion and bending strength, fracture toughness and sliding wear rate were evaluated. The results indicated that the addition of Al into Al₂O₃ was beneficial to decrease the splashing of impinging droplets and to increase the deposition efficiency. The Al₂O₃-Al composite coating exhibited homogeneously dispersed pores and the co-sprayed Al particles were considered to be distributed in the splat boundary. Compared with Al₂O₃ coating, the composite coating showed slightly lower hardness, whereas the coexistence of metal Al phase and Al₂O₃ ceramic phase effectively improved the toughness, strength and wear resistance of coatings.     

Effects of CeO2-ZrO2 present in Pd/Al2O3 catalysts on the redox behavior of PdOx and their combustion activity

The ceria-zirconium-modified alumina-supported palladium catalysts are prepared using impregnation method with H₂PdCl₄ as Pd source, hydrazine hydrate as reducing agent. The physicochemical properties of these catalysts are characterized by BET surface area (BET), X-ray powder diffraction (XRD), transmission electron microscopy (TEM), temperature programmed reduction (H₂-TPR) and temperature programmed oxidation (O₂-TPO) techniques, and their catalytic activities for the combustion of methane are examined. The results show that the palladium mainly exist in a highly dispersed PdO species on Ce-Zr-rich grains as well as Al₂O₃-rich grains surfaces, and a stable PdO species due to the strong interaction between PdO and CeO₂-ZrO₂ on the Ce-Zr/Al₂O₃ surfaces. The catalytic activity is strongly related to the redox behavior of PdO species highly dispersed on Ce-Zr-rich grains and Al₂O₃-rich grains surfaces, and the higher the reducibility of the PdO species, the higher the catalytic activity. The presence of Ce-Zr in Pd/Al₂O₃ catalyst would inhibit the site growth of PdO_x particles and decomposition of PdO to Pd⁰, and the reoxidation property of Pd⁰ to PdO_x is significantly improved, which obviously increases thermal stability and catalytic activity of Pd/Ce-Zr/Al₂O₃ catalyst for the methane combustion.     

Synthesis and characterization of monodisperse spherical core-shell structured SiO2@Y3Al5O12:Ce3+/Tb3+ phosphors for field emission displays

Nanocrystalline Y₃Al₅O₁₂: Ce³⁺/Tb³⁺ (average crystalline size 30 nm) phosphor layers were coated on non-aggregated, monodisperse and spherical SiO₂ particles by the sol-gel method, resulting in the formation of core-shell structured SiO₂@Y₃Al₅O₁₂:Ce³⁺/Tb³⁺ particles. X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, photoluminescence, cathodoluminescence spectra, as well as lifetimes were utilized to characterize the core-shell structured SiO₂@Y₃Al₅O₁₂:Ce³⁺/Tb³⁺ phosphor particles. The obtained core-shell structured phosphors consist of well-dispersed submicron spherical particles with a narrow size distribution. The thickness of the Y₃Al₅O₁₂:Ce³⁺/Tb³⁺ shells on the SiO₂ cores (average size about 500 nm, crystalline size about 30 nm) could be easily tailored by varying the number of deposition cycles (100 nm for four deposition cycles). Under the excitation of ultraviolet and low-voltage electron beams (1–3 kV), the core-shell SiO₂@Y₃Al₅O₁₂:Ce³⁺/Tb³⁺ particles show strong yellow-green and green emission corresponding to the 5d–4f emission of Ce³⁺ and ⁵D₄–⁷F _J (J = 6, 5, 4, 3) emission of Tb³⁺, respectively. These phosphors may have potential application in field emission displays.     

Al2O3钝化及其在晶硅太阳电池中的应用

介绍了Al₂O₃的材料性质及其原子层沉积制备方法, 详细阐述了该材料的钝化机制(化学钝化和场效应钝化), 并从薄膜厚度、热稳定性及叠层钝化等角度阐释其优化方案. 概述了Al₂O₃钝化在晶体硅太阳电池中的应用, 主要包括钝化发射极及背面局部扩散电池和钝化发射极及背表面电池. 最后, 对Al₂O₃钝化工艺的未来研究方向和大规模的工业应用进行了展望.